HMPP-386x Series MiniPak Surface Mount RF PIN Diodes Data Sheet Description/Applications Features These ultra-miniature products represent the blending of Avago Technologies' proven semiconductor and the latest in leadless packaging technology. * Surface mount MiniPak package The HMPP-386x series of general purpose PIN diodes are designed for two classes of applications. The first is attenuators where current consumption is the most important design consideration. The second application for this series of diodes is in switches where low capacitance with no reverse bias is the driving issue for the designer. * Single and dual versions The low dielectric relaxation frequency of the HMPP-386x insures that low capacitance can be reached at zero volts reverse bias at frequencies above 1 GHz, making this PIN diode ideal for hand held applications. Low junction capacitance of the PIN diode chip, combined with ultra low package parasitics, mean that these products may be used at frequencies which are higher than the upper limit for conventional PIN diodes. Note that Avago's manufacturing techniques assure that dice packaged in pairs are taken from adjacent sites on the wafer, assuring the highest degree of match. Minipak 1412 is a ceramic based package, while Minipak QFN is a leadframe based package. Package Lead Code Identification (Top View) Single 3 2 #0 (Minipak 1412) Anti-parallel 4 3 1 2 #2 (Minipak 1412) 3 1 2 4 1 #5 (Minipak 1412) * Matched diodes for consistent performance * Low capacitance at zero volts * Low resistance * Low FIT (Failure in Time) rate* * Six-sigma quality level * For more information, see the Surface Mount Schottky Reliability Data Sheet. Pin Connections and Package Marking 3 AA 2 Product code 4 1 Date code Notes: 1. Package marking provides orientation and identification. 2. See "Electrical Specifications" for appropriate package marking. Parallel 4 * Better thermal conductivity for higher power dissipation HMPP-386x Series Absolute Maximum Ratings [1], Tc = 25C Symbol Parameter Units MiniPak 1412 / MiniPak QFN If Forward Current (1 s pulse) Amp 1 PIV Peak Inverse Voltage V 100 Notes: 1. Operation in excess of any one of these conditions may result in permanent damage to the device. 2. TC = +25C, where TC is defined to be the temperature at the package pins where contact is made to the circuit board. Tj Junction Temperature C 150 ESD WARNING: Tstg Storage Temperature C -65 to +150 Handling Precautions Should Be Taken To Avoid Static Discharge. jc Thermal Resistance [2] C/W 150 MiniPak1412 Electrical Specifications, Tc = +25C, each diode Part Number HMPP- Package Marking Code Lead Code Configuration Minimum Breakdown Voltage (V) Typical Series Resistance () 3860 3862 3865 H F E 50 3.0/1.5* VR = VBR Measure IR 10 A IF = 10 mA f = 100 MHz *IF = 100 mA 0 2 5 Single Anti-parallel Parallel Test Conditions MiniPak1412 Typical Parameters, Tc = +25C Part Number HMPP- Total Resistance RT () Carrier Lifetime (ns) Reverse Recovery Time Trr (ns) Total Capacitance CT (pF) 3860 3862 3865 22 500 80 0.20 VR = 10 V IF = 20 mA 90% Recovery VR = 50V f = 1 MHz Test Conditions IF = 1 mA IF = 50 mA f = 100 MHz TR = 250 mA MiniPak 1412 HMPP-386x Series Typical Performance TC = +25 C (unless otherwise noted), each diode 1000 1 MHz 0.25 100 MHz 0.20 0.15 1 GHz 0 2 4 6 8 100 10 1 0.01 10 12 14 16 18 20 0.1 Figure 1. RF Capacitance vs. Reverse Bias. 100 VR = 5 V VR = 10 V 100 VR = 20 V 10 20 30 FORWARD CURRENT (mA) Figure 4. Reverse Recovery Time vs. Forward Current for Various Reverse Voltages. 10 1 0.1 0.01 125 C 0 0.2 0.4 25 C 0.6 -50 C 0.8 115 110 Diode Mounted as a Series Switch in a 50 Microstrip and Tested at 123 MHz Intercept point will be higher at higher frequencies 105 100 95 90 85 1 10 30 IF - FORWARD BIAS CURRENT (mA) 100 IF - FORWARD CURRENT (mA) Trr - REVERSE RECOVERY TIME (ns) 10 Figure 2. Typical RF Resistance vs. Forward Bias Current. 1000 1 BIAS CURRENT (mA) REVERSE VOLTAGE (V) 10 120 TA = +85 C TA = +25 C TA = -55 C INPUT INTERCEPT POINT (dBm) 0.30 RF RESISTANCE (OHMS) TOTAL CAPACITANCE (pF) 0.35 1.0 VF - FORWARD VOLTAGE (mA) Figure 5. Forward Current vs. Forward Voltage. 1.2 Figure 3. 2nd Harmonic Input Intercept Point vs. Forward Bias Current for Switch Diodes. Typical Applications RF COMMON RF COMMON 2 3 1 4 RF 1 RF 2 BIAS 1 3 4 3 4 2 1 2 1 RF 1 RF 2 BIAS 2 BIAS Figure 7. High Isolation SPDT Switch Using Dual Bias. Figure 6. Simple SPDT Switch Using Only Positive Bias. RF COMMON VARIABLE BIAS 1 4 RF 1 3 4 2 1 3 2 3 4 2 1 3 4 1 2 2 1 4 3 RF IN/OUT INPUT RF 2 FIXED BIAS VOLTAGE BIAS Figure 9. Four Diode p Attenuator. See AN1048 for details. Figure 8. Very High Isolation SPDT Switch, Dual Bias. Figure 9. Four Diode Attenuator. See AN1048 for details. BIAS 3 4 3 4 2 1 2 1 Figure 10. High Isolation SPST Switch (Repeat Cells as Required). Diode Lifetime and Resistance Dielectric Relaxation Frequency and Diode Capacitance The resistance of a PIN diode is controlled by the conductivity (or resistivity) of the I layer. This conductivity is controlled by the density of the cloud of carriers (charges) in the I layer (which is, in turn, controlled by the DC bias). Minority carrier lifetime, indicated by the Greek symbol , is a measure of the time it takes for the charge stored in the I layer to decay, when forward bias is replaced with reverse bias, to some predetermined value. This lifetime can be short (35 to 200 nsec. for epitaxial diodes) or it can be relatively long (400 to 3000 nsec. for bulk diodes). Lifetime has a strong influence over a number of PIN diode parameters, among which are distortion and basic diode behavior. fDR (Dielectric Relaxation Frequency) for a PIN diode is given by the equation f = 1 To study the effect of lifetime on diode behavior, we first define a cutoff frequency fC = 1/. For short lifetime diodes, this cutoff frequency can be as high as 30 MHz while for our longer lifetime diodes fC 400 KHz. At frequencies which are ten times fC (or more), a PIN diode does indeed act like a current controlled variable resistor. At frequencies which are one tenth (or less) of fC, a PIN diode acts like an ordinary PN junction diode. Finally, at 0.1fC f 10fC, the behavior of the diode is very complex. Suffice it to mention that in this frequency range, the diode can exhibit very strong capacitive or inductive reactance -- it will not behave at all like a resistor. The HMPP-386x family features a typical lifetime of 300 to 500 ns, so 10fC for this part is 5 MHz. At any frequency over 5 MHz, the resistance of this diode will follow the curve given in Figure 2. From this curve, it can be seen that the HMPP-386x family produces a lower resistance at a given value of bias current than most attenuator PIN diodes, making it ideal for applications where current consumption is important. DR 2 where... = bulk resistivity of the I-layer = 0 R = 10 -12 F/cm = bulk susceptance of silicon In the case of an epitaxial diode with a value for of 10cm, fDR will be in Ku-Band. For a bulk diode fabricated on very pure material, can be as high as 2000, resulting in a value of fDR of 80 MHz. The implications of a low fDR are very important in RF attenuator and switch circuits. At operating frequencies below fDR, reverse bias (as much as 50V) is needed to minimize junction capacitance. At operating frequencies well above fDR, the curve of capacitance vs. reverse bias is flat. For the HMPP-386x family, fDR is around 500 MHz, resulting in very low capacitance at zero bias for frequencies above 1 GHz. See Figure 1. Linear Equivalent Circuit In order to predict the performance of the HMPP-386x as a switch or an attenuator, it is necessary to construct a model which can then be used in one of the several linear analysis programs presently on the market. Such a model is given in Figure 16, where RS + Rj is given in Figure 2 and Cj is provided in Figure 1. Careful examination of Figure 16 will reveal the fact that the package parasitics (inductance and capacitance) are much lower for the MiniPak than they are for leaded plastic packages such as the SOT-23, SOT323 or others. This will permit the HMPP-386x family to be used at higher frequencies than its conventional leaded counterparts. 20 fF 3 30 fF 4 1.1 nH 2 30 fF 1 20 fF Single diode package (HMPP-3860) 20 fF 3 2 0.05 nH 30 fF 0.05 nH 0.5 nH 0.5 nH 0.5 nH 0.05 nH 12 fF 30 fF 0.05 nH 0.5 nH 4 1 20 fF Anti-parallel diode package (HMPP-3862) 20 fF 3 2 0.05 nH 30 fF 0.05 nH 0.5 nH 0.5 nH 0.5 nH 0.05 nH 12 fF 30 fF 0.05 nH 0.5 nH 4 1 20 fF Parallel diode package (HMPP-3865) Figure 11. Linear Equivalent Circuit of the MiniPak 1412 PIN Diode. MiniPak 1412 Outline Drawing 1.44 (0.057) 1.40 (0.055) 1.12 (0.044) 1.08 (0.043) 0.82 (0.032) 0.78 (0.031) 1.20 (0.047) 1.16 (0.046) 0.32 (0.013) 0.28 (0.011) 0.00 Top view 0.00 0.70 (0.028) 0.58 (0.023) Side view Dimensions are in millimeters (inches) -0.07 (-0.003) -0.03 (-0.001) 0.92 (0.036) 0.88 (0.035) 0.42 (0.017) 0.38 (0.015) Bottom view 1.32 (0.052) 1.28 (0.050) -0.07 (-0.003) -0.03 (-0.001) Assembly Information SMT Assembly The MiniPak diode is mounted to the PCB or microstrip board using the pad pattern shown in Figure 17. Reliable assembly of surface mount components is a complex process that involves many material, process, and equipment factors, including: method of heating (e.g., IR or vapor phase reflow, wave soldering, etc.) circuit board material, conductor thickness and pattern, type of solder alloy, and the thermal conductivity and thermal mass of components. Components with a low mass, such as the MiniPak package, will reach solder reflow temperatures faster than those with a greater mass. 0.4 0.5 0.4 0.3 0.5 0.3 Figure 12. PCB Pad Layout, MiniPak (dimensions in mm). This mounting pad pattern is satisfactory for most applications. However, there are applications where a high degree of isolation is required between one diode and the other is required. For such applications, the mounting pad pattern of Figure 18 is recommended. 0.40 mm via hole (4 places) 0.20 2.40 0.8 0.40 2.60 Figure 13. PCB Pad Layout, High Isolation MiniPak (dimensions in mm). This pattern uses four via holes, connecting the crossed ground strip pattern to the ground plane of the board. After ramping up from room temperature, the circuit board with components attached to it (held in place with solder paste) passes through one or more preheat zones. The preheat zones increase the temperature of the board and components to prevent thermal shock and begin evaporating solvents from the solder paste. The reflow zone briefly elevates the temperature sufficiently to produce a reflow of the solder. The rates of change of temperature for the ramp-up and cool-down zones are chosen to be low enough to not cause deformation of the board or damage to components due to thermal shock. The maximum temperature in the reflow zone (TMAX) should not exceed 260C. These parameters are typical for a surface mount assembly process for Avago diodes. As a general guideline, the circuit board and components should be exposed only to the minimum temperatures and times necessary to achieve a uniform reflow of solder. Ordering Information Part Number No. of Devices Container HMPP-386x-TR2 10000 13 Reel HMPP-386x-TR1 3000 7 Reel HMPP-386x-BLK 100 antistatic bag Device Orientation REEL TOP VIEW END VIEW 4 mm CARRIER TAPE AA AA AA COVER TAPE 8 mm AA USER FEED DIRECTION Note: "AA" represents package marking code. Package marking is right side up with carrier tape perforations at top. Conforms to Electronic Industries RS-481, "Taping of Surface Mounted Components for Automated Placement." Standard quantity is 3,000 devices per reel. Tape Dimensions and Product Orientation For Outline 4T (MiniPak 1412) P P2 D P0 E F W C D1 t 1 (CARRIER TAPE THICKNESS) K0 5 MAX. 5 MAX. A0 DESCRIPTION T t (COVER TAPE THICKNESS) B0 SYMBOL SIZE (mm) SIZE (INCHES) 0.002 0.002 0.002 0.004 0.002 LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A0 B0 K0 P D1 1.40 1.63 0.80 4.00 0.80 PERFORATION DIAMETER PITCH POSITION D P0 E 1.50 0.10 4.00 0.10 1.75 0.10 0.060 0.004 0.157 0.004 0.069 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 + 0.30 - 0.10 0.254 0.02 0.315 + 0.012 - 0.004 0.010 0.001 COVER TAPE WIDTH TAPE THICKNESS C Tt 5.40 0.10 0.062 0.001 0.213 0.004 0.002 0.00004 DISTANCE CAVITY TO PERFORATION (WIDTH DIRECTION) F 3.50 0.05 0.138 0.002 CAVITY TO PERFORATION (LENGTH DIRECTION) P2 2.00 0.05 0.079 0.002 For product information and a complete list of distributors, please go to our web site: 0.05 0.05 0.05 0.10 0.05 0.055 0.064 0.031 0.157 0.031 CAVITY www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2008 Avago Technologies. All rights reserved. Obsoletes 5989-3629EN AV02-0652EN - November 24, 2008