POWER SIL06C Series C-Class Non-Isolated Data Sheet Total Power: Input Voltage: # of Outputs: 30 Watts 4.5 - 13.8 Vdc Single SPECIAL FEATURES 6 A current rating Input voltage range: 4.5 - 5.5 Vdc or 10.2 - 13.8 Vdc Output voltage: 0.9 - 5.0 V Industry-leading value Cost optimized design Excellent transient response Output voltage adjustability Electrical Specifications Input Input voltage range 5 V input model 12 V input model 4.5 - 5.5 Vdc 10.2 - 13.8 Vdc Input current No load Remote OFF 50 mA 5 mA Input current (max.) (See Note 9) 5 V input model 12 V input model 5.1 A @ lo max. 1.6 A @ Io max. Input reflected ripple (See Note 2) 5 V input model 12 V input model 52 mA (pk-pk) 56 mA (pk-pk) Path for future upgrades Supports silicon voltage migration Reduced design-in and qual time Designed-in reliability: MTBF of 7 million hours per Telcordia SR-332 Available RoHS compliant Two year warranty SAFETY UL, cUL CAN/CSA 22.2 No. E139421 UL6950 File No. E139421 TUV Product Service (EN60950) Certificate No. B 04 08 19870 228 CB report and certificate to IEC60950 Remote ON/OFF Logic compatibility ON OFF Active high >2.4 Vdc <0.8 Vdc Start-up time Power up Remote ON/OFF <20 ms <20 ms Turn ON threshold 5 Vin 12 Vin 4.5 Vdc 9.0 Vdc Turn OFF threshold 5 Vin 12 Vin 4.3 Vdc 7.5 Vdc Voltage adjustability (See Note 7) 5 V input model 12 V input model 0.9 - 3.3 Vdc 0.9 - 5.0 Vdc Output setpoint accuracy with 1.0% trim resistors 2.5% Line regulation Low line to high line 0.2% Load regulation Full load to min. load 0.5% Output Min/Max load Overshoot (at turn on) 0 A/6 A 5 V input model 12 V input model Undershoot 3.0% max. 1.0% max. 100 mV max. Ripple and noise 5 Hz to 20 MHz (See Note 2) See table Transient response (See Note 1) Deviation 75 mV; 150 s recovery to within regulation band All specifications are typical at nominal input, full load at 25C unless otherwise stated. SIL06C Data Sheet General Specifications Efficiency Switching frequency Approvals and standards Fixed (See Note 4) Material flammability Weight MTBF Telcordia SR-332 Environmental Specifications See Table Thermal performance Operating ambient temperature -0 C to +80 C 200 kHz typical (See Note 8) Non-operating temperature -40 C to +125 C TUV Product Services EN60950, UL/cUL60950 Protection UL94V-0 Recommended System Capacitance 9.3 g (0.3 oz) Input capacitance (See Note 11) 270 F / 20 mW ESR max. Output capacitance (See Note 11) 680 F / 10 mW ESR max. Short-circuit Hiccup, non latching 7,562,142 hours Ordering Information Model Number (3,5) Regulation Output Power (Max.) Input Voltage Output Voltage Output Current (Min.) Output Current (Max.) Efficiency (Typical) Line Load SIL06C-05SADJ-VJ 20 W 4.5 - 5.5 Vdc 0.9 - 3.3 V 0A 6A 89% 0.2% 0.5% SIL06C-12SADJ-VJ 30 W 10.2 - 13.8 Vdc 0.9 - 5.0 V 0A 6A 91% 0.2% 0.5% Part Number System with Options Product Family SIL Rated Output Current Performance 06 Input Voltage C 06 = 06 Amps - C = Cost Optimized 12 Mounting Option - Single Adjustable Output V V = Vertical H = Horizontal Packaging Options J J = Pb free (RoHS 6/6 compliant) Notes: Output Voltage Adjustment The ultra-wide output voltage trim range offers major advantages to users who select the SIL06C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the SIL06C series converterleaves the factory the output has been adjusted to the default voltage of 0.9 V. 1. di/dt = 10 A/s, Vin = Nom, Tc = 25 C, load change = 0.5 lo max. to 0.75 lo max. and 0.75 lo max to 0.5 lo max. 2. Measured with external filter. See Application Note 131 for details. 3. Power up is the time from application of dc input to Power Good enabled. Remote ON/OFF is from ON/OFF asserted high to Power Good enabled. 4. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand-alone product. 5. The standard unit with the suffix `-V' is for vertical mounting. To order a unit with horizontal mounting, please add the suffix `-H' to the model number, e.g. SIL06C-05SADJ-HJ.6. Airflow dependent, 300 LFM minimum required. Ripple and Noise Specification Model SADJ 05 = 4.5 - 5.5 12 = 10.2 - 13.8 SIL = Single In Line Number of Outputs Output Voltage Pk - Pk RMS 5 V input models 0.9 - 2.5 Vdc 3.3 Vdc 30 mV 40 mV 15 mV 15 mV 12 V input models 0.9 - 2.5 Vdc 3.3 Vdc 40 mV 50 mV 20 mV 20 mV 6. Measured as per recommended set-up. Cin = 270 F (20 mW ESR max.). Cout = 680 F (10 mW ESR max.). 7. Uses external resistor from trim to output ground. Minimum value 485 for 5 V model, 280 for 12 V model. See Applications Note 131 for details. 8. Signal line assumed <3 m. 9. External input fusing recommended. 10. See Application Note 131 for operation above 50 C. 11. See Application Note 131 for more details. 12. These models have a wide trim output. 5 Vin has an output of 0.9 Vdc to 3.3 Vdc and 12 Vin has an output of 0.9 Vdc to 5 Vdc. An external resistor adjusts the output voltage. 13. To order a unit with a pin length of 0.150", please add suffix `P4' to the model number, e.g. SIL06C-05SADJ-HP4J. 14. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/power to find a suitable alternative. SIL06C Data Sheet Mechanical Drawings Mating Connectors Horizontal Mount 0.040 (1.02) 0.530 (15.01) 0.610 (15.49) 0.120 (3.05) 9 Places 0.150 (3.81) Ref 0.062 (1.57) PCB Ref 0.315 (8.00) max 1.200 (30.48) 0.050 (1.27) 0.025 0.001 (0.64) Typ. 0.025 Pin 1 0.015 (0.38) 0.150 (3.80) 0.527 (13.38) Pin 8 5X 0.100 (2.54) 0.950 (24.13) Mechanical Support Pin 0.025 0.001 (0.64) Typ. 0.025 All dimensions in INCHES (mm) General tolerance 0.01in ( 0.25mm) except where specified otherwise Vertical Mount Pin 1 0.025 0.001 (0.64) Typ. 0.025 0.050 (1.27) 0.315 (8.00) max. Pin Assignments Pin Function 1 2 3 4 5 6 7 8 9 Vout Trim Ground Power Good Remote ON/OFF Vin Mechanical support Mechanical support Mechanical support (Horiz only) 0.150 (3.81) 8 Places Pin 8 0.150 (3.81) 0.062 (1.57) Ref. 0.040 (1.02) Ref. 0.610 (15.49) 0.070 (1.78) 1.200 (30.48) 5X 0.100 (2.54) 0.050 (1.27) Typ. 0.025 0.001 (0.64) Typ. 0.025 0.950 (24.13) All dimensions in inches (mm) General tolerance 0.01in ( 0.25mm) except where specified otherwise WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. (c) 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com SIL06C DS 26Mar2015