AS1358-BTTT-15 - Austriamicrosystems

AS1358 / AS1359

150mA/300mA, Ultra-Low-Noise, High-PSRR Low Dropout Regulators

www.austriamicrosystems.com Revision 1.5 1 - 16

Datasheet

1 General Description

The AS1358 / AS1359 are ultra-low-noise, low-dropout linear

regulators specifically designed to deliver up to 150/300mA

continuous output current, and can achieve a low 140mV dropout for

300mA load current. The LDOs are designed and optimized to work

with low-cost, small-capacitance ceramic capacitors.

The devices are available as the standard products listed in Table 1.

An integrated P-channel MOSFET pass transistor allows the devices

to maintain extremely low quiescent current (40µA).

The AS1358 / AS1359 uses an advanced architecture to achieve

ultra-low output voltage noise of 9µVRMS and a power-supply

rejection-ratio of better than 80dB (up to 10kHz).

The AS1358 / AS1359 requires only 1µF output capacitor for stability

at any load. When the LDO is disabled, current consumption drops

below 500nA.

The devices are available in a TSOT23 5-pin package.

Figure 1. Typical Application Circuit

2 Key Features

Preset Output Voltages: 1.5V to 4.5V (in 50mV steps)

Output Noise: 9µVRMS @ 100Hz to 100kHz

Power-Supply Rejection Ratio: 92dB @ 1kHz

Low Dropout: 140mV @ 300mA Load

Stable with 1µF Ceramic Capacitor for any Load

Guaranteed 150mA / 300mA Output

1.25V Internal Reference

Extremely-Low Quiescent Current: 40µA

Excellent Load/Line Transient

Overcurrent and Thermal Protection

TSOT23 5-pin Package

3 Applications

The devices are ideal for mobile phones, wireless phones, PDAs,

handheld computers, mobile phone base stations, Bluetooth portable

radios and accessories, wireless LANs, digital cameras, personal

audio devices, and any other portable, battery-powered application.

Table 1. Standard Products

Model Load Current Output Voltage

AS1358 150mA Preset – 1.5V to 4.5V

AS1359 300mA Preset – 1.5V to 4.5V

AS1358 / AS1359

BYPASS

GND

OUT

SHDNN

CIN

1µF

Off

Input

2V to 5.5V

COUT

1µF

Output

1.5V to 4.5V

CBYPASS

10nF

www.austriamicrosystems.com Revision 1.5 2 - 16

AS1358 / AS1359

Datasheet - Pin Assignments

4 Pin Assignments

Figure 2. Pin Assignments (Top View)

4.1 Pin Descriptions

Table 2. Pin Descriptions

Pin Number Pin Name Description

1IN

Unregulated Input Supply.

2GND

Ground. Provides the electrical connection to system ground and also serves as a heat sink.

Connect pin GND to the system ground using a large pad or ground plane.

3 SHDNN Shutdown. Pull this pin low to disable the LDO.

4 BYPASS Noise Bypass for Low-Noise Operation. Connect a 10nF capacitor from this pin to OUT.

Note: This pin is shorted to GND in shutdown mode.

5OUT

Regulated Output Voltage. Bypass this pin with a capacitor to GND.

3SHDNN

2GND

1IN

4 BYPASS

5OUT

TSOT23 5-pin

AS1358 /

AS1359

www.austriamicrosystems.com Revision 1.5 3 - 16

AS1358 / AS1359

Datasheet - Absolute Maximum Ratings

5 Absolute Maximum Ratings

Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of

the device at these or any other conditions beyond those indicated in Electrical Characteristics on page 4 is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.

Table 3. Absolute Maximum Ratings

Parameter Min Max Units Comments

IN to GND -0.3 +7 V

OUT, SHDNN to GND -0.3 IN +0.3 V

BYPASS to GND -0.3 OUT +0.3 V

Output Short-Circuit Duration Infinite

Thermal Resistance JA 201.7 ºC/W

Junction-to-ambient thermal resistance is very dependent

on application and board-layout. In situations where high

maximum power dissipation exists, special attention must

be paid to thermal dissipation during board design.

Operating Temperature Range -40 +85 ºC

Junction Temperature +125 ºC

Storage Temperature Range -65 +150 ºC

Package Body Temperature +260 ºC

The reflow peak soldering temperature (body temperature)

specified is in accordance with IPC/JEDEC J-STD-020D

“Moisture/Reflow Sensitivity Classification for Non-

Hermetic Solid State Surface Mount Devices”.

The lead finish for Pb-free leaded packages is matte tin

(100% Sn).

www.austriamicrosystems.com Revision 1.5 4 - 16

AS1358 / AS1359

Datasheet - Electrical Characteristics

6 Electrical Characteristics

All limits are guaranteed. The parameters with Min and Max values are guaranteed by production tests or SQC (Statistical Quality Control)

methods.

VIN = VOUT +0.5V, CIN = 1µF, COUT = 1µF, CBYPASS = 10nF, TAMB = -40 to +85ºC (unless otherwise specified).

Typical values are at TAMB = +25ºC.

Table 4. Electrical Characteristics

Symbol Parameter Condition Min Typ Max Unit

VIN Input Voltage Range 2 5.5 V

Output Voltage Accuracy

IOUT = 1mA, TAMB = +25ºC -0.5 +0.5

IOUT = 100µA to 150mA,

TAMB = +25ºC (AS1358) -0.75 +0.75

IOUT = 100µA to 300mA,

TAMB = +25ºC (AS1359) -1.0 +1.0

IOUT = 100µA to 150mA, (AS1358) -1.5 +1.5

IOUT = 100µA to 300mA, (AS1359) -2.0 +2.0

IOUT Maximum Output Current AS1358 150 mA

AS1359 300

ILIMIT Current Limit AS1358, OUT = 90% of nom., TAMB = +25ºC 270 mA

AS1359, OUT = 90% of nom., TAMB = +25ºC 510

Dropout Voltage 1

1. Dropout is defined as VIN - VOUT when VOUT is 100mV below the value of VOUT for VIN = VOUT + 0.5V

VOUT  3V, IOUT = 150mA 70 95

VOUT  3V, IOUT = 300mA, (AS1359 only) 140 200

2.5V VOUT  3V, IOUT = 150mA 90 120

2.5V VOUT  3V, IOUT = 300mA,

(AS1359 only) 170 230

2.0V VOUT  2.5V, IOUT = 150mA 140 190

2.0V VOUT  2.5V, IOUT = 300mA,

(AS1359 only) 270 350

IQQuiescent Current IOUT = 0.05mA 40 90 µA

VIN = VOUTNOM - 0.1V, IOUT = 0mA 150 250

VLNR Line Regulation VIN = (VOUT +0.5V) to 5.5V, IOUT = 0.1mA 0.02 %/V

VLDR Load Regulation IOUT = 1 to 150mA / 300mA 0.0005 %/mA

ISHDNN Shutdown Supply Current SHDNN = 0V 9 500 nA

PSRR Ripple Rejection

f = 1kHz, IOUT = 10mA 92

dBf = 10kHz, IOUT = 10mA 80

f = 100kHz, IOUT = 10mA 62

Output Noise Voltage (RMS) f = 100Hz to 100kHz,

ILOAD = 0 to 150mA / 300mA 9µV

Shutdown

Shutdown Exit Delay 2

2. Time needed for VOUT to reach 90% of final value

RLOAD = 50300 µs

SHDNN Logic Low Level VIN = 2V to 5.5V 0.4 V

SHDNN Logic High Level VIN = 2V to 5.5V 1.5 V

Thermal Protection

TSHDNM Thermal Shutdown Temperature 160 ºC

TSHDNM Thermal Shutdown Hysteresis 15 ºC

www.austriamicrosystems.com Revision 1.5 5 - 16

AS1358 / AS1359

Datasheet - Typical Operating Characteristics

7 Typical Operating Characteristics

VIN = VOUT + 0.5V, CIN = COUT = 1µF, CBYPASS = 10nF, TAMB = 25°C (unless otherwise specified).

Figure 3. Output Voltage vs. Input Voltage Figure 4. Output Voltage Accuracy vs. Load Current

0.5

1.5

2.5

3.5

0123456

Input Voltage (V)

Output Voltage (V) .

IOUT = 300mA

IOUT = 150mA

-0.5

-0.4

-0.3

-0.2

-0.1

0.1

0.2

0.3

0.4

0.5

0 50 100 150 200 250 300

Load Current (mA)

Output Voltage Deviation (%) .

Temp = 85°C

Temp = 25°C

Temp = -4 5 °C

Figure 5. Output Voltage Accuracy vs. Temperature Figure 6. Dropout Voltage vs. Load Current

-1

-0.8

-0.6

-0.4

-0.2

0.2

0.4

0.6

0.8

-40 -15 10 35 60 85

Temperature (°C)

Output Voltage Deviation (%) .

100

120

140

0 50 100 150 200 250 300

Load Current (mA)

Dropout Voltage (mV) .

Temp = 85°C

Temp = 25°C

Temp = -4 5 °C

Figure 7. Dropout Voltage vs. Output Voltage Figure 8. Ground Pin Current vs. Input Voltage

2 2.2 2.4 2.6 2.8 3 3.2

Output Voltage (V)

Dropout Voltage (mV) .

100

125

150

0123456

Input Voltage (V)

Ground Pin Current (µA) .

IOUT = 0mA

IOUT= 300mA

IOUT = 150mA

www.austriamicrosystems.com Revision 1.5 6 - 16

AS1358 / AS1359

Datasheet - Typical Operating Characteristics

Figure 9. Ground Pin Current vs. Load Current Figure 10. Ground Pin Current vs. Temperature

0 50 100 150 200 250 300

Load Current (mA)

Ground Pin Current (µA) .

-40 -15 10 35 60 85

Temperature (°C)

Ground Pin Current (µA) .

Figure 11. PSRR vs. Frequency; IOUT = 10mA Figure 12. Output Noise Spectral Density vs. Frequency

100

1000

10000

0.01 0.1 1 10 100

Frequency (kHz)

Output Noise Density (nV/ Hz) .

Figure 13. Output Noise vs. Bypass Capacitance Figure 14. Load Transient Response, VIN = 3.8V, VOUT = 3.3V

110100

Capacitance (nF)

Noise (µVrms) .

200µs/Div

VOUT IOUT

20mV/DIV 20mA/Div

www.austriamicrosystems.com Revision 1.5 7 - 16

AS1358 / AS1359

Datasheet - Typical Operating Characteristics

Figure 15. Load Transient Response near Dropout,

VIN = 3.4V, VOUT = 3.3V

Figure 16. Line Transient Response

200µs/Div

VOUT IOUT

20mV/DIV 20mA/Div

200µs/Div

VOUT

20mV/DIV 500mV/Div

VIN

Figure 17. Enter & Exit Shutdown Delay

200µs/Div

2V/Div

VOUT SHDNN

2V/Div

www.austriamicrosystems.com Revision 1.5 8 - 16

AS1358 / AS1359

Datasheet - Detailed Description

8 Detailed Description

The AS1358 / AS1359 are ultra-low-noise, low-dropout, low-quiescent current linear-regulators specifically designed for space-limited

applications. The devices are available with preset output voltages from 1.5V to 4.5V in 50mV increments.

These devices can supply loads up to 150mA / 300mA. As shown in Figure 18, the AS1358 / AS1359 consist of an integrated bandgap core and

noise bypass circuitry, error amplifier, P-channel MOSFET pass transistor, and internal feedback voltage-divider.

Figure 18 shows the block diagram of the AS1358 / AS1359. It identifies the basics of a series linear regulator employing a 0.5 (typ) P-Channel

MOSFET as the control element. A stable voltage reference (REF in Figure 18) is compared with an attenuated sample of the output voltage.

Any difference between the two voltages (reference and sample) creates an output from the error amplifier that drives the series control element

to reduce the difference to a minimum. The error amplifier incorporates additional buffering to drive the relatively large gate capacitance of the

series pass P-channel MOSFET, when additional drive current is required under transient conditions. Input supply variations are absorbed by the

series element and output voltage variations with loading are absorbed by the low output impedance of the regulator.

The AS1358 / AS1359 deliver preset output voltages from 1.5V to 4.5V, in 50mV increments (see Ordering Information on page 15).

The output voltage is fed back through an internal resistor voltage-divider connected to pin OUT. An external bypass capacitor connected to pin

BYPASS reduces noise at the output. Startup time is minimized by internal power-on circuitry which pre-charges CBYPASS. Additional blocks

include a current limiter, thermal sensor, and shutdown logic.

Figure 18. AS1358 / AS1359 Block Diagram

OUT

SHDNN

BYPASS

GND

AS1358 /

AS1359

Thermal

Sensor

1.25 Reference and

Noise Bypass

Error

Amp

MOS

Driver w/

ILIMIT

Shutdown and

Power-Down

Control

www.austriamicrosystems.com Revision 1.5 9 - 16

AS1358 / AS1359

Datasheet - Application Information

9 Application Information

9.1 Dropout Voltage

Dropout is the input to output voltage difference, below which the linear regulator ceases to regulate. At this point, the output voltage change

follows the input voltage change. Dropout voltage may be measured at different currents and, in particular at the regulator maximum one. From

this is obtained the MOSFET maximum series resistance over temperature etc. More generally:

(EQ 1)

Dropout is probably the most important specification when the regulator is used in a battery application. The dropout performance of the

regulator defines the useful “end of life” of the battery before replacement or re-charge is required.

Figure 19. Graphical Representation of Dropout Voltage

Figure 19 shows the variation of VOUT as VIN is varied for a certain load current. The practical value of dropout is the differential voltage (VOUT-

VIN) measured at the point where the LDO output voltage has fallen by 100mV below the nominal, fully regulated output value. The nominal

regulated output voltage of the LDO is that obtained when there is 500mV (or greater) input-output voltage differential.

9.2 Efficiency

Low quiescent current and low input-output voltage differential are important in battery applications amongst others, as the regulator efficiency is

directly related to quiescent current and dropout voltage. Efficiency is given by:

Efficiency = % (EQ 2)

Where:

IQ = Quiescent current of LDO

VDROPOUT ILOAD RSERIES

=

Dropout

Voltage

100mV

VIN

VOUT

VIN

VOUT

VIN =V

OUT(TYP) +0.5V

VIN

VLOAD ILOAD



VIN IQILOAD

+

---------------------------------------100

www.austriamicrosystems.com Revision 1.5 10 - 16

AS1358 / AS1359

Datasheet - Application Information

9.3 Power Dissipation

Maximum power dissipation (PD) of the LDO is the sum of the power dissipated by the internal series MOSFET and the quiescent current

required to bias the internal voltage reference and the internal error amplifier, and is calculated as:

Watts (EQ 3)

Internal power dissipation as a result of the bias current for the internal voltage reference and the error amplifier is calculated as:

Watts (EQ 4)

Total LDO power dissipation is calculated as:

Watts (EQ 5)

9.4 Junction Temperature

Under all operating conditions, the maximum junction temperature should not be allowed to exceed 125ºC (unless the data sheet specifically

allows). Limiting the maximum junction temperature requires knowledge of the heat path from junction to case (JCºC/W fixed by the IC

manufacturer), and adjustment of the case to ambient heat path (CAºC/W) by manipulation of the PCB copper area adjacent to the IC position.

Figure 20. Package Physical Arrangements

Figure 21. Steady State Heat Flow Equivalent Circuit

PD MAX

SeriespassILOAD MAX

=VIN MAX

VOUT MIN

–

PD MAX

BiasVIN MAX

PD MAX

TotalPD MAX

SeriespassPD MAX

+Bias=

Bond Wire

Chip

PCB

Package

Lead Frame

SOTxx Package

Junction

TJ°C

Package

TC°C

PCB/Heatsink

TS°C

Ambient

TA°C

Chip

Power

RJC RCS RSA

www.austriamicrosystems.com Revision 1.5 11 - 16

AS1358 / AS1359

Datasheet - Application Information

Total Thermal Path Resistance:

(EQ 6)

Junction Temperature (TJºC) is determined by:

ºC (EQ 7)

9.5 Explanation of Steady State Specifications

9.5.1 Line Regulation

Line regulation is defined as the change in output voltage when the input (or line) voltage is changed by a known quantity. It is a measure of the

regulator’s ability to maintain a constant output voltage when the input voltage changes. Line regulation is a measure of the DC open loop gain

of the error amplifier. More generally:

Line Regulation = and is a pure number (EQ 8)

In practise, line regulation is referred to the regulator output voltage in terms of % / VOUT. This is particularly useful when the same regulator is

available with numerous output voltage trim options.

Line Regulation = % / V (EQ 9)

9.5.2 Load Regulation

Load regulation is defined as the change of the output voltage when the load current is changed by a known quantity. It is a measure of the

regulator’s ability to maintain a constant output voltage when the load changes. Load regulation is a measure of the DC closed loop output

resistance of the regulator. More generally:

Load Regulation = and is units of ohms ()(EQ 10)

In practise, load regulation is referred to the regulator output voltage in terms of % / mA. This is particularly useful when the same regulator is

available with numerous output voltage trim options.

Load Regulation = % / mA (EQ 11)

9.5.3 Setting Accuracy

The regulator is supplied pre-trimmed, so that the output voltage accuracy is fully defined in the output voltage specification.

9.5.4 Total Accuracy

Away from dropout, total steady state accuracy is the sum of setting accuracy, load regulation and line regulation. Generally:

Total % Accuracy = Setting % Accuracy + Load Regulation % + Line Regulation % (EQ 12)

9.6 Explanation of Dynamic Specifications

9.6.1 Power Supply Rejection Ratio (PSRR)

Known also as Ripple Rejection, this specification measures the ability of the regulator to reject noise and ripple beyond DC. PSRR is a

summation of the individual rejections of the error amplifier, reference and AC leakage through the series pass transistor. The specification, in

the form of a typical attenuation plot with respect to frequency, shows up the gain bandwidth compromises forced upon the designer in low

quiescent current conditions. Generally:

PSSR = dB using lower case to indicate AC values (EQ 13)

Power supply rejection ratio is fixed by the internal design of the regulator. Additional rejection must be provided externally.

RJA RJC RCS RSA

++=

TJPD MAX

RJA

TAMB

VOUT

VIN

----------------

VOUT

VIN

---------------- 100

VOUT

------------



VOUT

IOUT

----------------

VOUT

IOUT

---------------- 100

VOUT

----------------



20LogVOUT

VIN

----------------



www.austriamicrosystems.com Revision 1.5 12 - 16

AS1358 / AS1359

Datasheet - Application Information

9.6.2 Output Capacitor ESR

The series regulator is a negative feedback amplifier, and as such is conditionally stable. The ESR of the output capacitor is usually used to

cancel one of the open loop poles of the error amplifier in order to produce a single pole response. Excessive ESR values may actually cause

instability by excessive changes to the closed loop unity gain frequency crossover point. The range of ESR values for stability is usually shown

either by a plot of stable ESR versus load current, or a limit statement in the datasheet.

Some ceramic capacitors exhibit large capacitance and ESR variations with temperature. Z5U and Y5V capacitors may be required to ensure

stability at temperatures below TAMB = -10ºC. With X7R or X5R capacitors, a 1.0µF capacitor should be sufficient at all operating temperatures.

Larger output capacitor values (2.2µF max) help to reduce noise and improve load transient-response, stability and power-supply rejection.

9.6.3 Input Capacitor

An input capacitor at VIN is required for stability. It is recommended that a 1.0µF capacitor be connected between the AS1358 / AS1359 power

supply input pin VIN and ground (capacitance value may be increased without limit subject to ESR limits). This capacitor must be located at a

distance of not more than 1cm from the VIN pin and returned to a clean analog ground. Any good quality ceramic, tantalum, or film capacitor may

be used at the input.

9.6.4 Noise

The regulator output is a DC voltage with noise superimposed on the output. The noise comes from three sources; the reference, the error

amplifier input stage, and the output voltage setting resistors. Noise is a random fluctuation and if not minimized in some applications, will

produce system problems. The AS1358/9 architecture provides enhance noise reduction when an external 10nF capacitor is connected between

Bypass and Output pins, and 1µF connected as the output capacitor.

The leakage current going into the BYPASS pin should be less than 10nA. Increasing the capacitance slightly decreases the output noise.

Values above 0.1µF and below 0.001µF are not recommended.

9.6.5 Transient Response

The series regulator is a negative feedback system, and therefore any change at the output will take a finite time to be corrected by the error

loop. This “propagation time” is related to the bandwidth of the error loop. The initial response to an output transient comes from the output

capacitance, and during this time, ESR is the dominant mechanism causing voltage transients at the output. More generally:

Units are Volts, Amps, Ohms. (EQ 14)

Thus an initial +50mA change of output current will produce a -12mV transient when the ESR=240m. Remember to keep the ESR within

stability recommendations when reducing ESR by adding multiple parallel output capacitors.

After the initial ESR transient, there follows a voltage droop during the time that the LDO feedback loop takes to respond to the output change.

This drift is approximately linear in time and sums with the ESR contribution to make a total transient variation at the output of:

Units are Volts, Seconds, Farads, Ohms. (EQ 15)

Where:

CLOAD is output capacitor

T = Propagation delay of the LDO

This shows why it is convenient to increase the output capacitor value for a better support for fast load changes. Of course the formula holds for

t < “propagation time”, so that a faster LDO needs a smaller cap at the load to achieve a similar transient response. For instance 50mA load

current step produces 50mV output drop if the LDO response is 1usec and the load cap is 1µF.

There is also a steady state error caused by the finite output impedance of the regulator. This is derived from the load regulation specification

discussed above.

9.6.6 Turn On Time

This specification defines the time taken for the LDO to awake from shutdown. The time is measured from the release of the enable pin to the

time that the output voltage is within 5% of the final value. It assumes that the voltage at VIN is stable and within the regulator Min and Max limits.

Shutdown reduces the quiescent current to very low, mostly leakage values (<1µA).

9.6.7 Thermal Protection

To prevent operation under extreme fault conditions, such as a permanent short circuit at the output, thermal protection is built into the device.

Die temperature is measured, and when a 160ºC threshold is reached, the device enters shutdown. When the die cools sufficiently, the device

will restart (assuming input voltage exists and the device is enabled). Hysteresis of 15ºC prevents low frequency oscillation between start-up and

shutdown around the temperature threshold.

VTRANSIENT IOUTPUT RESR

=

VTRANSIENT IOUTPUT

=RESR

CLOAD

----------------







www.austriamicrosystems.com Revision 1.5 13 - 16

AS1358 / AS1359

Datasheet - Package Drawings and Markings

10 Package Drawings and Markings

The devices are available in a TSOT23 5-pin package.

Figure 22. TSOT23 5-pin Package

Notes:

1. Dimensioning and tolerancing conform to ASME Y14.5M - 1994.

2. Dimensions are in millimeters.

3. Dimension D does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, and gate burrs shall not exceed 0.15mm per

end. Dimension E1 does not include interlead flash or protrusion. Interlead flash or protrusion shall not exceed 0.15mm per side. Dimen-

sions D and E1 are determined at datum H.

4. The package top can be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic

body exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but include any mistmatches between the top of the package

body and the bottom. D and E1 are determined at datum H.

Symbol Min Typ Max Notes Symbol Min Typ Max Notes

A 1.00 L 0.30 0.40 0.50

A1 0.01 0.05 0.10 L1 0.60REF

A2 0.84 0.87 0.90 L2 0.25BSC

b 0.30 0.45 N 5

b1 0.31 0.35 0.39 R 0.10

c 0.12 0.15 0.20 R1 0.10 0.25

c1 0.08 0.13 0.16 0º 4º 8º

D 2.90BSC 3,4 14º 10º 12º

E 2.80BSC 3,4 Tolerances of Form and Position

E1 1.60BSC 3,4 aaa 0.15

e 0.95BSC bbb 0.25

e1 1.90BSC ccc 0.10

ddd 0.20

www.austriamicrosystems.com Revision 1.5 14 - 16

AS1358 / AS1359

Datasheet

Revision History

Note: Typos may not be explicitly mentioned under revision history.

Revision Date Owner Description

1.4 - afe Initial revisions

1.5 13 Jun, 2012

www.austriamicrosystems.com Revision 1.5 15 - 16

AS1358 / AS1359

Datasheet - Ordering Information

11 Ordering Information

The devices are available as the standard products shown in Table 5.

Non-standard devices from 1.5V to 4.5V are available in 50mV steps. For more information and inquiries contact

http://www.austriamicrosystems.com/contact

Note: All products are RoHS compliant and Pb-free.

Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect

For further information and requests, please contact us mailto:sales@austriamicrosystems.com

or find your local distributor at http://www.austriamicrosystems.com/distributor

Table 5. Ordering Information

Ordering Code Marking Output Current Output Voltage Delivery Form Package

AS1358-BTTT-15 ASLI 150mA 1.5V Tape and Reel TSOT23 5-pin

AS1358-BTTT-18 ASLJ 150mA 1.8V Tape and Reel TSOT23 5-pin

AS1358-BTTT-25 ASLK 150mA 2.5V Tape and Reel TSOT23 5-pin

AS1358-BTTT-26 ASLL 150mA 2.6V Tape and Reel TSOT23 5-pin

AS1358-BTTT-27 ASLM 150mA 2.7V Tape and Reel TSOT23 5-pin

AS1358-BTTT-28 ASLN 150mA 2.8V Tape and Reel TSOT23 5-pin

AS1358-BTTT-285 ASLO 150mA 2.85V Tape and Reel TSOT23 5-pin

AS1358-BTTT-30 ASLP 150mA 3.0V Tape and Reel TSOT23 5-pin

AS1358-BTTT-33 ASLQ 150mA 3.3V Tape and Reel TSOT23 5-pin

AS1358-BTTT-45 ASLR 150mA 4.5V Tape and Reel TSOT23 5-pin

AS1359-BTTT-15 ASLS 300mA 1.5V Tape and Reel TSOT23 5-pin

AS1359-BTTT-18 ASLT 300mA 1.8V Tape and Reel TSOT23 5-pin

AS1359-BTTT-25 ASLU 300mA 2.5V Tape and Reel TSOT23 5-pin

AS1359-BTTT-26 ASLV 300mA 2.6V Tape and Reel TSOT23 5-pin

AS1359-BTTT-27 ASLW 300mA 2.7V Tape and Reel TSOT23 5-pin

AS1359-BTTT-28 ASLX 300mA 2.8V Tape and Reel TSOT23 5-pin

AS1359-BTTT-285 ASLY 300mA 2.85V Tape and Reel TSOT23 5-pin

AS1359-BTTT-30 ASLZ 300mA 3.0V Tape and Reel TSOT23 5-pin

AS1359-BTTT-31 ASSA 300mA 3.1V Tape and Reel TSOT23 5-pin

AS1359-BTTT-33 ASL0 300mA 3.3V Tape and Reel TSOT23 5-pin

AS1359-BTTT-45 ASL1 300mA 4.5V Tape and Reel TSOT23 5-pin

www.austriamicrosystems.com Revision 1.5 16 - 16

AS1358 / AS1359

Datasheet - Ordering Information

Copyrights

the copyright owner.

All products and companies mentioned are trademarks or registered trademarks of their respective companies.

Disclaimer

Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale.

austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding

the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at

any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for

current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range,

unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are

specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100

parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location.

The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not

be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use,

interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing,

performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of

austriamicrosystems AG rendering of technical or other services.

Contact Information

Headquarters

austriamicrosystems AG

Tobelbaderstrasse 30

A-8141 Unterpremstaetten, Austria

Tel: +43 (0) 3136 500 0

Fax: +43 (0) 3136 525 01

For Sales Offices, Distributors and Representatives, please visit:

http://www.austriamicrosystems.com/contact