WSXS-SPIBUS TD - Teledyne LeCroy

I2C, SPI, UART,

RS-232

Serial Data

Trigger and

Decode

The Most Intuitive Decode

Advanced software algorithms

decon struct the waveform into

protocol information, then overlay

the decoded data on the waveform.

Decode information condenses

or expands depending on the

timebase/zoom ratio setting, so

understanding messages is easy.

Various sections of the protocol

are color-coded to make it easy

to understand, especially for users

new to I2C, SPI, UART, and RS-232

serial data. The decode operation is

fast—even with long acquisitions.

The user can choose to decode into

Hex, Binary, or ASCII formats.

Teledyne LeCroy’s decode algorithms

allow the CLOCK signal to be input to

the external channel, which saves

valuable channels for other signals.

Or, if the CLOCK signal is input to

a channel, it can be turned OFF as

desired to reduce display clutter.

Powerful Conditional

Data Triggering

Completely isolate speciﬁc I2C,

SPI, UART, or RS-232 message

events for better understanding

and debug. Use a conditional DATA

trigger to select a range of DATA

values to trigger on, not just a single

DATA value. Oftentimes, I2C utilizes

DATA bytes to specify sub-addresses

for accessing memory locations in

EEPROMs. Condi tional DATA trigger

allows triggering on a range of DATA

bytes that correspond to reads or

writes to speciﬁc sub-address memory

blocks in the EEPROM. It can also

aid in monitoring DATA outputs from

I2C-based sensors, such as analog-to-

digital con verters, and triggering

when DATA is outside a safe operating

range. In both cases, verifying proper

operation becomes a simple task.

Of course, all the basic I2C and SPI

triggering capability you would expect

is also included.

Full UART and RS-232

Capability and Customization

Complete support for any conﬁgura-

tion of UART and standard RS-232.

Generic UART is commonly used

as the backbone for proprietary

protocols, and the ﬂexible setup

conﬁguration allows deﬁnition to meet

your exact need.

Key Features

• I2C, SPI, UART and RS-232

Trigger and Decode

• Color-coded decode overlaid

on the waveform is intuitive

and easy to read

•

Powerful and ﬂexible

conditional DATA triggering

(=, not =, >, >=, <, <=, <>, in

range, out of range).

• Hex, Binary or ASCII decoding

• Decode information expands

as the timebase is adjusted

or zoomed

• Convenient table display with

quick “zoom to message”

capability

• Quick search capability for

speciﬁc messages

• Set an ACK condition (ACK,

NO ACK, Don’t Care) in all

frame trigger setups (I2C)

• Decode does not require clock

trace to be displayed (I2C, SPI)

• Supports UART address (9-bit)

Byte triggering

• Supports trigger and decode

of user deﬁned proprietary

protocols based on a UART

backbone

Color-coded overlaid protocol decode makes it easy to understand your serial data messages.

POWERFUL TRIGGERING, INTUITIVE DECODING

Flexible Triggering

I2C, SPI, and UART all have special

use cases and the Teledyne LeCroy

Trigger and Decode solutions address

these cases. The I2C trigger can be

conﬁgured for 7 or 10-bit addressing

with out without inclusion of the R/W

bit. The SPI trigger can be conﬁgured

for a range of CPOL and CPHA set-

tings as well as the Simpliﬁed SPI

protocol. With the UART trigger 8 and

9-bit (8+1) formats are supported.

Convenient Table Display

Summarizes Results

Turn your oscilloscope into a protocol

analyzer with the Table display

of protocol information. Custom

conﬁgure the Table to display

only the infor mation you want, and

export Table data to an Excel ﬁle.

Touch a message in the table and

auto matically zoom for detail. In

all cases, the Table never obscures

your waveform data.

Search and Zoom

I2C, SPI, UART, and RS-232

messages can be quickly located

by search ing on Address (I2C) or

DATA (I2C, SPI, UART, RS-232).

Pressing an arrow button advances

the single zoomed message view

one message to the right or left

of the current message. Search through long record of decoded data by entering the message

or address you are looking for and clicking the right or left search

arrows.

Display your values in an easy-to-understand table. Touch a row to zoom, or export to

Excel with one button push.

Simultaneously decode up to 4 serial data buses. When using the MSO option on

WaveRunner Xi or WaveSurfer Xs the digital inputs D0, D1, D2, etc. can be used as

the source for a serial data trigger and decode.

continues

I2Cbus TD SPIbus TD UART-RS232bus TD

Deﬁnition

Protocol Setup N.A. Select CPOL, CPHA, DATA = MSB

or LSB.

Also, may select SIOP or SSPI defaults.

For UART

Select BitRate

Select # Data Bits (5-9)

Select Parity (Odd, Even, None)

Select # Stop Bits (1, 1.5, 2)

Select Bit Order (MSB or LSB)

Select Polarity (IdleLow or IdleHigh)

For RS-232

Select BitRate

Select # Data Bits (5-8)

Select Parity (Odd, Even, None)

Select # Stop Bits (1, 1.5, 2)

Decode Capability

Format Hexadecimal, Binary, ASCII Hexadecimal, Binary, ASCII Hexadecimal, Binary, or ASCII

Decode Setup Threshold deﬁnition required.

Default is to Percent amplitude.

Choose to Decode address values

including/not including the R/W bit in

address value.

Threshold deﬁnition required.

Default is to Percent amplitude.

Select CPOL, CPHA, DATA = MSB

or LSB.

Threshold deﬁnition required. Default is

to Percent amplitude. Select BitRate, #

Data Bits, Parity, # Stop Bits, Bit Order,

and Polarity (for RS-232, no Bit Order or

Polarity setup).

Decode Input Any analog Channel, Memory, or Math

trace.

# of Decode

Waveforms

Up to 4 buses may be decoded at

one time.

Sources can be Channels or Memory

Waveforms.

In addition, zooms can be displayed (with

decoded information).

Up to 4 buses may be decoded at

one time.

Sources can be Channels or Memory

Waveforms.

In addition, zooms can be displayed

(with decoded information).

Up to 4 buses may be decoded at

one time.

In addition, zooms can be displayed

(with decoded information).

Location Overlaid over DATA waveform, on Grid Overlaid over DATA waveform, on Grid Overlaid over DATA waveform, on

Grid. (Note: Use multi-grid if there is

more than one decoder ON)

Visual Aid Color Coding for FRAME, START/

ReSTART bit, ADDR, R/W, DATA,

ACK, and STOP bit

Color Coding for FRAME and DATA Color Coding for Start Bit, Stop

Bit, Parity Bit, and DATA. Decode

information is intelligently annotated

based on timebase setting.

Trigger Capability

Format Hexadecimal or Binary.

ADDRESS and DATA can be set up with

different formats.

Hexadecimal or Binary Hexadecimal or Binary

Trigger Setup Trigger on START, ReSTART, STOP,

ADDR, DATA, ADDR+DATA, Data

Length, Missing ACK

Trigger on DATA Trigger on DATA or Parity ERROR

ADDRESS

(ID) Condition

Setup

Specify one ADDRESS with condition

of = 7 or 10-bit ADDRESS supported with

full Read, Write, or R/W=”Don’t Care”

selectability on both 7 and

10-bit ADDRESSes

Choose to Trigger on address values

that include/don’t include R/W bit in

address value.

N.A. N.A.

DATA Condition

Setup

<=, <, =, >, >=, <>, in range, out of

range, don’t care.

=<=, <, =, >, >=, <>, in range, out of

range, don’t care.

SPECIFICATIONS

I2Cbus TD SPIbus TD UART-RS232bus TD

DATA Setup Hexadecimal: # Data Bytes = 0 to 12.

Data can be deﬁned by nibble.

Binary: Any combination of 0,1, or X for

1-96 bits.

Data pattern can be set to start on any

byte in a 2048-byte window (EEPROM

mode only).

Hexadecimal: # Data Bytes = 0 to 12.

Data can be deﬁned by nibble.

Binary: Any combination of 0,1, or X for

1-96 bits.

Triggers on that data pattern in a speciﬁed

location.

Hexadecimal: # Data Bytes = 0 to 12.

Data can be deﬁned by nibble.

Binary: Any combination of 0,1, or X for

1-96 bits.

May specify particular data position

anywhere in a 2048 byte sequence.

ACK Condition

Setup

For any ADDR, ADDR+DATA,

ADDR+DATA LENGTH, or EEPROM

frame setup, select an ACK Condition of

ACK, NO ACK, and DON’T CARE.

N.A. N.A.

Bit RatesFull range over I2C speciﬁcation for

Standard, Fast, Fast-Mode Plus, and High-

speed modes.

Auto-detected

Any.

Auto-detected

Any from 300 b/s to 10 Mb/s

(User settable)

Trigger Input Any analog Channel or the EXT input.

Clock may be input to EXT to conserve

available analog Channels.

Any analog Channel or the EXT input.

Clock or Slave Select may be input to EXT

to conserve available analog Channels.

Any analog Channel or the EXT input.

Trigger Design Internal to oscilloscope, settable like any

other oscilloscope trigger

Internal to oscilloscope, settable like any

other oscilloscope trigger

Internal to oscilloscope, settable like any

other oscilloscope trigger.

Search Capability

Pattern Search Search by ADDRESS or DATA in

Hexadecimal format

Search by ADDRESS or DATA in

Hexadecimal format

Search by DATA in Hexadecimal

formats, or for Next ERROR.

Other

Compatible

With

TD (Trigger & Decode) Option compatible

with all WaveMaster 8Zi/Zi-A, WavePro 7Zi/

Zi-A, WaveRunner 6Zi, WaveRunner® Xi

and WaveSurfer® Xs

TD (Trigger & Decode) Option compatible

with all WaveMaster® 8 Zi/Zi-A,

WavePro® 7 Zi/Zi-A, WaveRunner® 6Zi,

WaveRunner® Xi and WaveSurfer® Xs

TD (Trigger & Decode) Option compatible

with all WaveMaster® 8 Zi/Zi-A, WavePro®

7 Zi/Zi-A, WaveRunner® 6Zi, WaveRunner

Xi and WaveSurfer Xs

Ordering Information

Produt or brand names are trademarks or requested trademarks of their respective holders.

i2c-spiuart_ds_10june13

Product Description Product Code

I2C Trigger and Decode Option for WaveRunner Xi WRXi-I2Cbus TD

I2C Trigger and Decode Option for WaveRunner 6Zi WR6Zi-I2Cbus TD

I2C Trigger and Decode Option for WavePro Zi/Zi-A WPZi-I2Cbus TD

I2C Trigger and Decode Option for WaveSurfer MXs-B WSXs-I2Cbus TD

I2C Trigger and Decode Option for WaveMaster 8Zi/Zi-A WM8Zi-I2Cbus TD

SPI Trigger and Decode Option for WaveRunner Xi WRXi-SPIbus TD

SPI Trigger and Decode Option for WaveRunner 6Zi WR6Zi-SPIbus TD

SPI Trigger and Decode Option for WavePro Zi/Zi-A WPZi-SPIbus TD

SPI Trigger and Decode Option for WaveSurfer MXs-B WSXs-SPIbus TD

SPI Trigger and Decode Option for WaveMaster 8Zi/Zi-A WM8Zi-SPIbus TD