EC3700ETTTS-100.000M TR REGULATORY COMPLIANCE (Data Sheet downloaded on Jan 19, 2018) 2011/65 + 2015/863 174 SVHC ITEM DESCRIPTION Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 2.5Vdc 4 Pad 3.2mm x 5.0mm Ceramic Surface Mount (SMD) 100.000MHz 100ppm -40C to +85C ELECTRICAL SPECIFICATIONS Nominal Frequency 100.000MHz Frequency Tolerance/Stability 100ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25C, Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Ouput Load Change, First Year Aging at 25C, Shock, and Vibration) Operating Temperature Range -40C to +85C Supply Voltage 2.5Vdc 5% Input Current 13mA Maximum Output Voltage Logic High (Voh) 90% of Vdd Minimum (IOH = -4mA) Output Voltage Logic Low (Vol) 10% of Vdd Maximum (IOL = +4mA) Rise/Fall Time 3nSec Maximum (Measured at 20% to 80% of waveform) Duty Cycle 50 5(%) (Measured at 50% of waveform) Load Drive Capability 15pF Maximum Output Logic Type CMOS Pin 1 Connection Tri-State (High Impedance) Tri-State Input Voltage (Vih and Vil) 90% of Vdd Minimum or No Connect to Enable Output, 10% of Vdd Maximum to Disable Output (High Impedance) Standby Current 10A Maximum (Disabled Output: High Impedance) RMS Phase Jitter 1pSec Maximum (12kHz to 20MHz offset frequency) Start Up Time 10mSec Maximum Storage Temperature Range -55C to +125C ENVIRONMENTAL & MECHANICAL SPECIFICATIONS ESD Susceptibility MIL-STD-883, Method 3015, Class 1, HBM: 1500V Fine Leak Test MIL-STD-883, Method 1014, Condition A Flammability UL94-V0 Gross Leak Test MIL-STD-883, Method 1014, Condition C Mechanical Shock MIL-STD-883, Method 2002, Condition B Moisture Resistance MIL-STD-883, Method 1004 Moisture Sensitivity J-STD-020, MSL 1 Resistance to Soldering Heat MIL-STD-202, Method 210, Condition K Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010, Condition B Vibration MIL-STD-883, Method 2007, Condition A www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 1 of 5 Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EC3700ETTTS-100.000M TR MECHANICAL DIMENSIONS (all dimensions in millimeters) 3.20 0.20 1.00 0.20 (x4) MARKING ORIENTATION 5.00 0.20 1.3 MAX 2 3 1.20 0.20 CONNECTION 1 Tri-State 2 Ground 3 Output 4 Supply Voltage LINE MARKING 2.54 0.15 1 PIN 4 1 E100.00 E=Ecliptek Designator 2 XXXXX XXXXX=Ecliptek Manufacturing Identifier 1.20 0.20 (x4) Suggested Solder Pad Layout All Dimensions in Millimeters 1.20 (X4) 1.40 (X4) Solder Land (X4) 1.14 1.00 All Tolerances are 0.1 www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 2 of 5 Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EC3700ETTTS-100.000M TR CLOCK OUTPUT TRI-STATE INPUT OUTPUT WAVEFORM & TIMING DIAGRAM VIH VIL VOH 80% of Waveform OUTPUT DISABLE (HIGH IMPEDANCE STATE) 50% of Waveform 20% of Waveform VOL tPLZ Fall Time Rise Time tPZL TW T Duty Cycle (%) = TW/T x 100 www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 3 of 5 Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 EC3700ETTTS-100.000M TR Test Circuit for CMOS Output Frequency Counter Oscilloscope + + Power Supply _ Current Meter _ Supply Voltage (VDD) Probe (Note 2) Output + Voltage Meter _ 0.01F (Note 1) 0.1F (Note 1) Ground CL (Note 3) No Connect or Tri-State Note 1: An external 0.1F low frequency tantalum bypass capacitor in parallel with a 0.01F high frequency ceramic bypass capacitor close to the package ground and VDD pin is required. Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth (>300MHz) passive probe is recommended. Note 3: Capacitance value CL includes sum of all probe and fixture capacitance. www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 4 of 5 Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200 PART NUMBER DATA SHEET EC3700ETTTS-100.000M TR Tape & Reel Dimensions Quantity Per Reel: 1,000 units All Dimensions in Millimeters Compliant to EIA-481 4.00 0.10 0.60 MAX DIA 1.50 +0.10/-0.00 0.10 MAX 2.00 0.10 1.75 0.10 7.50 0.10 MARKING ORIENTATION 16.00 0.30 DIA 1.50 MIN 8.00 0.10 B0 A0 K0 Direction of Unreeling 1.50 MIN 22.40 MAX DIA 40 MIN Access Hole at Slot Location 180 MAX DIA 50 MIN DIA 20.20 MIN DIA 13.00 0.20 2.50 MIN Width 10 MIN Depth Tape slot in Core for Tape Start 16.40 +2.00/-0.00 www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 5 of 5 Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200