Date: 19.09.2005 IXYS Data Sheet Issue: 3 Thyristor/Diode Modules M## 500 Absolute Maximum Ratings VRRM VDRM [V] MCC MCD MDC MCA MCK MCDA MDCA 2000 500-20io1 500-20io1 500-20io1 500-20io1 500-20io1 500-20io1 500-20io1 2200 500-22io1 500-22io1 500-22io1 500-22io1 500-22io1 500-22io1 500-22io1 VOLTAGE RATINGS VDRM VDSM VRRM VRSM Repetitive peak off-state voltage 1) Non-repetitive peak off-state voltage Repetitive peak reverse voltage 1) 1) Non-repetitive peak reverse voltage 1) OTHER RATINGS IT(AV)M IT(AV)M IT(AV)M V 2000-2200 V 2100-2300 V MAXIMUM LIMITS UNITS A Maximum average on-state current. TC = 85C 460 A 323 A 1071 A 879 A 14.0 kA Maximum average on-state current. TC = 100C 2) 2) Peak non-repetitive surge tp = 10 ms, VRM = 60%VRRM Peak non-repetitive surge tp = 10 ms, VRM 10V 2 I t capacity for fusing tp = 10 ms, VRM = 60%VRRM 2 I t capacity for fusing tp = 10 ms, VRM 10 V 2 3) 3) 2 (di/dt)cr 2000-2200 500 D.C. on-state current, TC = 55C It V 2) IT(d.c.) It 2000-2200 2) Nominal RMS on-state current, TC = 55C ITSM2 UNITS Maximum average on-state current, TC = 80C IT(RMS)M ITSM MAXIMUM LIMITS 15.4 3) 3) Critical rate of rise of on-state current (repetitive) 4) Critical rate of rise of on-state current (non-repetitive) 4) kA 0.98x10 6 As 2 1.19x10 6 As 2 150 A/s 300 A/s VRGM Peak reverse gate voltage 5 V PG(AV) Mean forward gate power 4 W PGM Peak forward gate power 30 W 3500 V 5) VISOL Isolation Voltage Tvj op Operating temperature range -40 to +125 C Tstg Storage temperature range -40 to +150 C Notes: 1) 2) 3) 4) 5) De-rating factor of 0.13% per C is applicable for Tvj below 25C. Single phase; 50 Hz, 180 half-sinewave. Half-sinewave, 125C Tvj initial. VD = 67% VDRM, IFG = 2 A, tr 0.5s, TC = 125C. AC RMS voltage, 50 Hz, 1min test Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 Page 1 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Thyristor Characteristics PARAMETER MIN. TYP. MAX. TEST CONDITIONS 1) UNITS VTM Maximum peak on-state voltage - - 1.65 ITM = 1700 A V VTM Maximum peak on-state voltage - - 1.57 ITM = 1500 A V VT0 Threshold voltage - - 0.88 V rT Slope resistance - - 0.46 m (dv/dt)cr Critical rate of rise of off-state voltage 1000 - - IDRM Peak off-state current - - IRRM Peak reverse current - VGT Gate trigger voltage IGT VD = 80% VDRM, linear ramp, Gate o/c V/s 70 Rated VDRM mA - 70 Rated VRRM mA - - 3.0 Gate trigger current - - 300 IH Holding current - - 1000 tgd Gate controlled turn-on delay time - 0.6 1.5 tgt Turn-on time - 1.2 2.5 Qrr Recovered Charge - 3000 - Qra Recovered Charge, 50% chord - 1800 2400 Irm Reverse recovery current - 140 - trr Reverse recovery time, 50% chord - 26 - - 200 - tq Turn-off time - 300 - - - 0.062 Single Thyristor K/W - - 0.031 Whole Module K/W - - 0.02 Single Thyristor K/W - - 0.01 Whole Module K/W 4.25 - 5.75 RthJC Thermal resistance, junction to case RthCH Thermal resistance, case to heatsink F1 Mounting force (to heatsink) F2 Mounting force (to terminals) Wt Weight 10.2 - 13.8 - 1.5 - MIN. TYP. V Tvj = 25C, VD = 10 V, IT = 3 A mA Tvj = 25C mA IFG = 2 A, tr = 0.5 s, VD = 67%VDRM, ITM = 2000 A, di/dt = 10 A/s, Tvj = 25C s C ITM = 1000 A, tp = 1 ms, di/dt = 10A/s, VR = 50 V C A s ITM = 1000 A, tp = 1 ms, di/dt = 10 A/s, VR = 50 V, VDR = 80%VDRM, dvDR/dt = 20 V/s ITM = 1000 A, tp = 1 ms, di/dt = 10 A/s, VR = 50 V, VDR = 80%VDRM, dvDR/dt = 200 V/s s Nm 2) Nm kg Diode Characteristics PARAMETER MAX. TEST CONDITIONS 1) UNITS VFM Maximum peak forward voltage - - 1.09 ITM = 1700 A V VT0 Threshold voltage - - 0.72 V rT Slope resistance - - 0.143 m IRRM Peak reverse current - - 50 Qrr Recovered Charge - 2200 - Qra Recovered Charge, 50% chord - 1800 2250 Irm Reverse recovery current - 145 - trr Reverse recovery time, 50% chord - 25 - Rated VRRM mA C ITM = 1000 A, tp = 1ms, di/dt = 10 A/s, VR = 50 V C A s Notes: 1) Unless otherwise indicated Tvj=125C. 2) Screws must be lubricated Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 Page 2 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Notes on Ratings and Characteristics 1.0 Voltage Grade Table VDRM VDSM VRRM V 2000 2200 Voltage Grade 20 22 VRSM V 2100 2300 VD VR DC V 1250 1350 2.0 Extension of Voltage Grades This report is applicable to other voltage grades when supply has been agreed by Sales/Production. 3.0 De-rating Factor A blocking voltage de-rating factor of 0.13%/C is applicable to this device for Tvj below 25C. 4.0 Repetitive dv/dt Standard dv/dt is 1000V/s. 5.0 Snubber Components When selecting snubber components, care must be taken not to use excessively large values of snubber capacitor or excessively small values of snubber resistor. Such excessive component values may lead to device damage due to the large resultant values of snubber discharge current. If required, please consult the factory for assistance. 6.0 Rate of rise of on-state current The maximum un-primed rate of rise of on-state current must not exceed 300A/s at any time during turnon on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not exceed 150A/s at any time during turn-on. Note that these values of rate of rise of current apply to the total device current including that from any local snubber network. 7.0 Gate Drive The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least 30V is assumed. This gate drive must be applied when using the full di/dt capability of the device. IGM 4A/s IG tp1 The magnitude of IGM should be between five and ten times IGT, which is shown on page 2. Its duration (tp1) should be 20s or sufficient to allow the anode current to reach ten times IL, whichever is greater. Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The `back-porch' current IG should remain flowing for the same duration as the anode current and have a magnitude in the order of 1.5 times IGT. Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 Page 3 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 8.0 Computer Modelling Parameters 8.1 Thyristor Dissipation Calculations 2 I AV = WAV = 2 - VT 0 + VT 0 + 4 ff rT WAV 2 ff 2 rT and: T Rth T = T j max - TK Where VT0 = 0.88 V, rT = 0.46 m, Rth = Supplementary thermal impedance, see table below and ff = Form factor, see table below. Supplementary Thermal Impedance Conduction Angle 30 60 90 120 180 270 d.c. Square wave 0.07067 0.06791 0.06629 0.06525 0.06395 0.06277 0.062 Sine wave 0.06767 0.06536 0.06408 0.0633 0.062 Form Factors Conduction Angle 30 60 90 120 180 270 d.c. Square wave 3.464 2.449 2 1.732 1.414 1.149 1 Sine wave 3.98 2.778 2.22 1.879 1.57 8.2 Calculating VT/VF using ABCD Coefficients The on-state/forward characteristics, IT vs. VT, on pages 6 & 9 are represented in two ways; (i) the well established VT0 and rT tangent used for rating purposes and (ii) a set of constants A, B, C, D, forming the coefficients of the representative equation for VT in terms of IT given below: VT = A + B ln (I T ) + C I T + D I T The constants, derived by curve fitting software, are given below for both hot and cold characteristics. The resulting values for VT agree with the true device characteristic over a current range, which is limited to that plotted. Thyristor coefficients 25C 125C A 2.296566505 0.617965877 B -0.3387419 0.01056009 -5 -4 C -6.25982x10 2.13809x10 D 0.04767141 0.01430982 Diode coefficients 25C 125C A 0.578986196 -0.214099731 B 0.1048225 0.2916851 -4 C 1.61162x10 D -7.480625x10 Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 -3 Page 4 of 11 -4 5.15459x10 -0.04232154 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 8.3 D.C. Thermal Impedance Calculation -t rt = rp 1 - e p p =1 p=n Where p = 1 to n n t rt rp p = = = = = number of terms in the series Duration of heating pulse in seconds. Thermal resistance at time t. Amplitude of pth term. Time Constant of rth term. The coefficients for this device are shown in the tables below: D.C. Term 1 2 3 -3 4 -3 -3 rp 0.05428 4.4894x10 2.3382x10 0.8759x10 p 2.69428 0.126017 0.013878 1.435x10 -3 9.0 Reverse recovery ratings (i) Qra is based on 50% Irm chord as shown in Fig. 1 Fig. 1 (ii) Qrr is based on a 150 s integration time i.e. 150 s Qrr = i rr .dt 0 (iii) K Factor = t1 t2 Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 Page 5 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Thyristor Curves Figure 1 - On-state characteristics of Limit device Figure 2 - Transient thermal impedance 0.1 10000 M##500-20io1-22io1 Issue 3 Tj = 25C M##500-20io1-22io1 Issue 3 Single Thyristor Tj = 125C Thermal impedance (K/W) Instantaneous On-state current - I TM (A) 0.01 1000 0.001 0.0001 100 0 0.5 1 1.5 2 2.5 3 0.00001 0.00001 0.0001 3.5 Instantaneous On-state voltage - VTM (V) 0.1 1 10 100 Figure 4 - Gate characteristics - Power curves 35 M##500-20io1-22io1 Issue 3 Tj=25C M##500-20io1-22io1 Issue 3 Tj=25C 7 30 6 Max VG dc Gate Trigger Voltage - VGT (V) 4 IGT, VGT 20 15 PG Max 30W dc 10 -40C 25C -10C 3 2 Max VG dc 25 5 125C Gate Trigger Voltage - VGT (V) 0.01 Time (s) Figure 3 - Gate characteristics - Trigger limits 8 0.001 PG 4W dc 5 1 Min VG dc IGD, VGD Min VG dc 0 0 0 0.2 0.4 0.6 0.8 0 1 Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 2 4 6 8 10 Gate Trigger Current - IGT (A) Gate Trigger Current - IGT (A) Page 6 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Figure 5 - Total recovered charge, Qrr 10000 Figure 6 - Recovered charge, Qra (50% chord) 10000 M##500-20io1-22io1 Issue 3 Tj=125C M##500-20io1-22io1 Issue 3 Tj=125C 2000A 1500A 1000A Recovered charge - Qrr (C) Recovered charge - Qra, 50% chord (C) 500A 1000 2000A 1500A 1000A 500A 1000 1 10 100 1000 1 10 di/dt (A/s) 100 Figure 7 - Peak reverse recovery current, Irm Figure 8 - Maximum recovery time, trr (50% chord) 100 10000 M##500-20io1-22io1 Issue 3 Tj=125C M##500-20io1-22io1 Issue 3 Reverse recovery time (50% chord) - trr (s) Tj=125C Reverse recovery current - Irm (A) 1000 di/dt (A/s) 2000A 1500A 1000A 500A 1000 100 10 2000A 1500A 1000A 500A 1 10 1 10 100 1 1000 Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 10 100 1000 di/dt (A/s) di/dt (A/s) Page 7 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Figure 9 - On-state current vs. Power dissipation - Sine wave 1800 Figure 10 - On-state current vs. case temperature - Sine wave 140 M##500-20io1-22io1 Issue 3 1600 60 M##500-20io1-22io1 Issue 3 180 90 120 120 30 Maximum permissable heatsink temperature (C) Maximum forward dissipation (W) 1400 1200 1000 800 600 100 80 60 40 400 30 20 60 90 120 180 200 0 0 0 200 400 600 800 0 1000 Figure 11 - On-state current vs. Power dissipation - Square wave 1800 200 400 600 800 1000 Mean forward current (A) (Whole cycle averaged) Mean forward current (A) (Whole cycle averaged) Figure 12 - On-state current vs. case temperature - Square wave 140 M##500-20io1-22io1 Issue 3 M##500-20io1-22io1 Issue 3 1600 120 Maximum permissible heatsink temperature (C) Maximum forward dissipation (W) 1400 1200 d.c. 270 180 120 90 60 30 1000 800 600 100 80 30 60 90 120 180 270 d.c. 60 40 400 20 200 0 0 0 200 400 600 800 1000 1200 1400 0 Mean Forward Current (Amps) (Whole Cycle Averaged) Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 200 400 600 800 1000 1200 1400 Mean Forward Current (Amps) (Whole Cycle Averaged) Page 8 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 2 Figure 13 - Maximum surge and I t Ratings Gate may temporarily lose control of conduction angle 1.00E+07 I2t: VRRM 10V I2t: 60% VRRM Maximum I2t (A2s) Total peak half sine surge current (A) 100000 1.00E+06 10000 ITSM: VRRM 10V ITSM: 60% VRRM Tj (initial) = 125C M##500-20io1-22io1 Issue 3 1000 1 3 5 10 1 5 Duration of surge (ms) 10 50 1.00E+05 100 Duration of surge (cycles @ 50Hz) Diode curves Figure 14 - Instantaneous forward voltage VF Figure 15 - Transient thermal impedance 0.1 10000 M##500-20io1-22io1 Issue 3 Single Diode M##500-20io1-22io1 Issue 3 Tj = 125C Tj = 25C Thermal impedance (K/W) Instantaneous On-state current - IFM (A) 0.01 1000 0.001 0.0001 0.00001 100 0 0.5 1 1.5 2 0.000001 1E-05 0.0001 0.001 2.5 Instantaneous On-state voltage - VFM (V) Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 0.01 0.1 1 10 100 Time (s) Page 9 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Figure 16 - Total recovered charge, Qrr 10000 Figure 17 - Recovered charge, Qra (50% chord) 10000 M##500-20io1-22io1 Issue 3 Tj=125C M##500-20io1-22io1 Issue 3 Tj=125C 2000A 1500A Recovered charge - Qra, 50% chord (C) 1000A Recovered charge - Qrr (C) 500A 1000 2000A 1500A 1000A 500A 1000 1 10 100 1000 1 10 di/dt (A/s) Figure 18 - Peak reverse recovery current, Irm 1000 Figure 19 - Maximum recovery time, trr (50% chord) 100 10000 M##500-20io1-22io1 Issue 3 Tj=125C Reverse recovery time (50% chord) - trr (s) M##500-20io1-22io1 Issue 3 Tj=125C Reverse recovery current - Irm (A) 100 di/dt (A/s) 2000A 1500A 1000A 500A 1000 10 2000A 1500A 1000A 500A 1 100 1 10 100 1 1000 Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 10 100 1000 di/dt (A/s) di/dt (A/s) Page 10 of 11 September, 2005 IXYS Thyristor/Diode Module Types M##500-20io1 and M##500-22io1 Outline Drawing & Ordering Information 3 67 1 5 4 2 3 1 5 4 2 3 67 1 2 1 5 4 2 MCC MCD MDC 376 MCA 3 67 1 4 5 2 3 1 5 4 2 37 6 1 2 MCK MCDA MDCA ORDERING INFORMATION M ## Fixed Type Code Configuration code CC, CD, DC, CA, CK, CDA, DCA (Please quote 11 digit code as below) 500 io 1 Average Current Rating Voltage code VRRM/100 20-22 i = Critical dv/dt 1000 V/s o = Typical turn-off time Fixed Version Code Order code: MCD500-20io1- MCD configuration, 2000V VRRM IXYS IXYS Semiconductor GmbH Edisonstrae 15 D-68623 Lampertheim Tel: +49 6206 503-0 Fax: +49 6206 503-627 E-mail: marcom@ixys.de IXYS Corporation 3540 Bassett Street Santa Clara CA 95054 USA Tel: +1 (408) 982 0700 Fax: +1 (408) 496 0670 E-mail: sales@ixys.net www.ixys.com WESTCODE An Westcode Semiconductors Ltd Langley Park Way, Langley Park, Chippenham, Wiltshire, SN15 1GE. Tel: +44 (0)1249 444524 Fax: +44 (0)1249 659448 E-mail: WSL.sales@westcode,com Westcode Semiconductors Inc 3270 Cherry Avenue Long Beach CA 90807 USA Tel: +1 (562) 595 6971 Fax: +1 (562) 595 8182 E-mail: WSI.sales@westcode.com IXYS Company www.westcode.com The information contained herein is confidential and is protected by Copyright. The information may not be used or disclosed except with the written permission of and in the manner permitted by the proprietors IXYS Semiconductors GmbH. (c) IXYS Semiconductor GmbH. In the interest of product improvement, IXYS reserves the right to change specifications at any time without prior notice. Devices with a suffix code (2-letter, 3-letter or letter/digit/letter combination) added to their generic code are not necessarily subject to the conditions and limits contained in this report. Rating Report. Types M##500-20io1 and M##500-22io1 Issue 3 Page 11 of 11 September, 2005