NSPM0061 ESD Protection Diode Features * Protection for the following IEC Standards: * IEC61000-4-2 Level 4: 30 kV Contact Discharge IEC61000-4-5 (Lightning) 70 A (8/20 ms) These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant 1 Cathode MAXIMUM RATINGS Rating IEC 61000-4-2 (ESD) www.onsemi.com Symbol Value Unit 30 30 kV TJ, Tstg -65 to +150 C IPP 70 A Contact Air Operating Junction and Storage Temperature Range Maximum Peak Pulse Current 8/20 ms @ TA = 25C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 2 Anode MARKING DIAGRAM UDFN2 CASE 517CZ F M FM = Specific Device Code = Date Code ORDERING INFORMATION Device Package Shipping NSPM0061MUT5G UDFN2 (Pb-Free) 8000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. (c) Semiconductor Components Industries, LLC, 2017 October, 2017 - Rev. 2 1 Publication Order Number: NSPM0061/D NSPM0061 ELECTRICAL CHARACTERISTICS I (TA = 25C unless otherwise noted) IF Parameter Symbol IPP Maximum Reverse Peak Pulse Current VC Clamping Voltage @ IPP VRWM IR VBR IT VC VBR VRWM Working Peak Reverse Voltage V IR VF IT Maximum Reverse Leakage Current @ VRWM Breakdown Voltage @ IT Test Current *See Application Note AND8308/D for detailed explanations of datasheet parameters. IPP Uni-Directional ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise specified) Parameter Reverse Working Voltage Breakdown Voltage (Note 1) Symbol Conditions Min Typ VRWM VBR IT = 1 mA 6.5 Unit 6.3 V 9.0 V 1 mA IPP = 1 A, tp = 8 x 20 ms 7.5 V VC IPP = 35 A, tp = 8 x 20 ms 9.5 V Clamping Voltage (Note 2) VC IPP = 70 A, tp = 8 x 20 ms 11.5 V Junction Capacitance CJ VR = 0 V, f = 1 MHz Dynamic Resistance RDYN Reverse Leakage Current IR VRWM = 6.3 V Clamping Voltage (Note 2) VC Clamping Voltage (Note 2) TLP Pulse 7.3 Max 12 pF 0.04 W Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. 1. Breakdown voltage is tested from pin 1 to 2 and pin 2 to 1. 2. Non-repetitive current pulse at TA = 25C, per IEC61000-4-5 waveform. www.onsemi.com 2 NSPM0061 14 9 8 12 7 10 Vpk (V) 5 4 3 6 2 1 0 8 4 2 0 5 10 15 20 25 0 30 0 10 20 30 40 50 60 70 Ipk (A) Ipk (A) Figure 1. Positive TLP I-V Curve Figure 2. Clamping Voltage vs. Peak Pulse Current (tp = 8/20 ms) 50 45 40 35 C (pF) Vpk (V) 6 30 25 20 15 10 5 0 0 1 2 3 4 VBias (V) Figure 3. CV Characteristics www.onsemi.com 3 5 6 80 NSPM0061 Transmission Line Pulse (TLP) Measurement L Transmission Line Pulse (TLP) provides current versus voltage (I-V) curves in which each data point is obtained from a 100 ns long rectangular pulse from a charged transmission line. A simplified schematic of a typical TLP system is shown in Figure 4. TLP I-V curves of ESD protection devices accurately demonstrate the product's ESD capability because the 10s of amps current levels and under 100 ns time scale match those of an ESD event. This is illustrated in Figure 5 where an 8 kV IEC 61000-4-2 current waveform is compared with TLP current pulses at 8 A and 16 A. A TLP I-V curve shows the voltage at which the device turns on as well as how well the device clamps voltage over a range of current levels. For more information on TLP measurements and how to interpret them please refer to AND9007/D. S Attenuator / 50 W Coax Cable 10 MW IM 50 W Coax Cable VM DUT VC Oscilloscope Figure 4. Simplified Schematic of a Typical TLP System Figure 5. Comparison Between 8 kV IEC 61000-4-2 and 8 A and 16 A TLP Waveforms www.onsemi.com 4 NSPM0061 IEC61000-4-2 Waveform IEC 61000-4-2 Spec. Ipeak Level Test Voltage (kV) First Peak Current (A) Current at 30 ns (A) Current at 60 ns (A) 1 2 7.5 4 2 2 4 15 8 4 3 6 22.5 12 6 4 8 30 16 8 100% 90% I @ 30 ns I @ 60 ns 10% tP = 0.7 ns to 1 ns Figure 6. IEC61000-4-2 Spec Device ESD Gun Under Oscilloscope Test 50 W 50 W Cable Figure 7. Diagram of ESD Test Setup ESD Voltage Clamping at the device level. ON Semiconductor has developed a way to examine the entire voltage waveform across the ESD protection diode over the time domain of an ESD pulse in the form of an oscilloscope screenshot, which can be found on the datasheets for all ESD protection diodes. For more information on how ON Semiconductor creates these screenshots and how to interpret them please refer to AND8307/D. For sensitive circuit elements it is important to limit the voltage that an IC will be exposed to during an ESD event to as low a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per the IEC61000-4-2 waveform. Since the IEC61000-4-2 was written as a pass/fail spec for larger systems such as cell phones or laptop computers it is not clearly defined in the spec how to specify a clamping voltage % OF PEAK PULSE CURRENT 100 PEAK VALUE IRSM @ 8 ms tr 90 PULSE WIDTH (tP) IS DEFINED AS THAT POINT WHERE THE PEAK CURRENT DECAY = 8 ms 80 70 60 HALF VALUE IRSM/2 @ 20 ms 50 40 30 tP 20 10 0 0 20 40 t, TIME (ms) 60 Figure 8. 8 x 20 ms Pulse Waveform www.onsemi.com 5 80 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS UDFN2 1.6x1.0, 1.1P CASE 517CZ ISSUE D SCALE 4:1 DATE 02 JUL 2020 GENERIC MARKING DIAGRAM* XXM XX M = Specific Device Code = Date Code *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G", may or not be present. Some products may not follow the Generic Marking. DOCUMENT NUMBER: DESCRIPTION: 98AON88716F UDFN2 1.6x1.0, 1.1P Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2018 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative