LM2734Z LM2734Z/LM2734ZQ Thin SOT23 1A Load Step-Down DC-DC Regulator Literature Number: SNVS334D LM2734Z/LM2734ZQ Thin SOT23 1A Load Step-Down DC-DC Regulator General Description Features The LM2734Z regulator is a monolithic, high frequency, PWM step-down DC/DC converter assembled in a 6-pin Thin SOT23 and LLP non pull back package. It provides all the active functions to provide local DC/DC conversion with fast transient response and accurate regulation in the smallest possible PCB area. With a minimum of external components and online design support through WEBENCH(R)TM, the LM2734Z is easy to use. The ability to drive 1A loads with an internal 300m NMOS switch using state-of-the-art 0.5m BiCMOS technology results in the best power density available. The world class control circuitry allows for on-times as low as 13ns, thus supporting exceptionally high frequency conversion over the entire 3V to 20V input operating range down to the minimum output voltage of 0.8V. Switching frequency is internally set to 3MHz, allowing the use of extremely small surface mount inductors and chip capacitors. Even though the operating frequency is very high, efficiencies up to 85% are easy to achieve. External shutdown is included, featuring an ultra-low stand-by current of 30nA. The LM2734Z utilizes current-mode control and internal compensation to provide high-performance regulation over a wide range of operating conditions. Additional features include internal soft-start circuitry to reduce inrush current, pulse-by-pulse current limit, thermal shutdown, and output over-voltage protection. Thin SOT23-6 package, or 6 lead LLP package 3.0V to 20V input voltage range 0.8V to 18V output voltage range 1A output current 3MHz switching frequency 300m NMOS switch 30nA shutdown current 0.8V, 2% internal voltage reference Internal soft-start Current-Mode, PWM operation Thermal shutdown LM2734ZQ is AEC-Q100 Grade 1 qualified and is manufactured on an Automotive Grade Flow Applications DSL Modems Local Point of Load Regulation Battery Powered Devices USB Powered Devices Automotive Typical Application Circuit Efficiency vs Load Current VIN = 5V, VOUT = 3.3V 20130301 20130345 WEBENCHTM is a trademark of Transim. (c) 2008 National Semiconductor Corporation 201303 www.national.com LM2734Z/LM2734ZQ Thin SOT23 1A Load Step-Down DC-DC Regulator June 12, 2008 LM2734Z/LM2734ZQ Connection Diagrams 20130305 20130360 6-Lead TSOT NS Package Number MK06A 6-Lead LLP (3mm x 3mm) NS Package Number SDE06A Ordering Information Order Number Package Type NSC Package Drawing LM2734ZMK LM2734ZMKX LM2734ZQMKE TSOT-6 MK06A Package Marking Supplied As SFTB 1000 Units on Tape and Reel SFTB 3000 Units on Tape and Reel SVBB Features LM2734ZQMKX SVBB 250 Units on Tape and Reel AEC-Q100 Grade 1 1000 Units on Tape and Reel Qualified. Automotive-Grade Production Flow* 3000 Units on Tape and Reel LM2734ZSD L163B 1000 Units on Tape and Reel LM2734ZSDX L163B 4500 Units on Tape and Reel L238B 250 Units on Tape and Reel AEC-Q100 Grade 1 1000 Units on Tape and Reel Qualified. Automotive-Grade Production Flow* 4500 Units on Tape and Reel LM2734ZQMK LM2734ZQSDE SVBB 6-Lead LLP SDE06A LM2734ZQSD L238B LM2734ZQSDX L238B *Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including defect detection methodologies. Reliability qualification is compliant with the requirements and temperature grades defined in the AEC-Q100 standard. Automotive grade products are identified with the letter Q. For more information go to http://www.national.com/automotive. Pin Descriptions Pin Name Function 1 BOOST Boost voltage that drives the internal NMOS control switch. A bootstrap capacitor is connected between the BOOST and SW pins. 2 GND 3 FB Feedback pin. Connect FB to the external resistor divider to set output voltage. 4 EN Enable control input. Logic high enables operation. Do not allow this pin to float or be greater than VIN + 0.3V. 5 VIN Input supply voltage. Connect a bypass capacitor to this pin. 6 SW Output switch. Connects to the inductor, catch diode, and bootstrap capacitor. DAP GND www.national.com Signal and Power ground pin. Place the bottom resistor of the feedback network as close as possible to this pin for accurate regulation. The Die Attach Pad is internally connected to GND 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN SW Voltage Boost Voltage Boost to SW Voltage FB Voltage EN Voltage Junction Temperature ESD Susceptibility (Note 2) Storage Temp. Range Operating Ratings -0.5V to 24V -0.5V to 24V -0.5V to 30V -0.5V to 6.0V -0.5V to 3.0V -0.5V to (VIN + 0.3V) 150C 2kV -65C to 150C 220C 260C (Note 1) VIN SW Voltage Boost Voltage Boost to SW Voltage Junction Temperature Range 3V to 20V -0.5V to 20V -0.5V to 25V 1.6V to 5.5V -40C to +125C Thermal Resistance JA (Note 3) TSOT23-6 118C/W Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those in boldface type apply over the full Operating Temperature Range (TJ = -40C to 125C). VIN = 5V, VBOOST - VSW = 5V unless otherwise specified. Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Symbol VFB VFB/VIN IFB UVLO Parameter Conditions Feedback Voltage Feedback Voltage Line Regulation VIN = 3V to 20V Feedback Input Bias Current Sink/Source Undervoltage Lockout VIN Rising Undervoltage Lockout VIN Falling Min (Note 4) Typ (Note 5) Max (Note 4) Units 0.784 0.800 0.816 V 0.01 %/V 10 250 2.74 2.90 2.0 2.3 nA V UVLO Hysteresis 0.30 0.44 0.62 FSW Switching Frequency 2.2 3.0 3.6 DMAX Maximum Duty Cycle 78 85 % DMIN Minimum Duty Cycle 8 % RDS(ON) Switch ON Resistance VBOOST - VSW = 3V (TSOT Package) 300 600 m VBOOST - VSW = 3V (LLP Package) 340 650 m 1.7 2.5 A 2.5 mA 6 mA ICL Switch Current Limit VBOOST - VSW = 3V IQ Quiescent Current Switching 1.5 Quiescent Current (shutdown) VEN = 0V 30 Boost Pin Current (Switching) Shutdown Threshold Voltage VEN Falling Enable Threshold Voltage VEN Rising IEN Enable Pin Current Sink/Source ISW Switch Leakage IBOOST VEN_TH MHz 1.2 4.25 nA 0.4 1.8 V 10 nA 40 nA Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see Electrical Characteristics. Note 2: Human body model, 1.5k in series with 100pF. Note 3: Thermal shutdown will occur if the junction temperature exceeds 165C. The maximum power dissipation is a function of TJ(MAX) , JA and TA . The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/JA . All numbers apply for packages soldered directly onto a 3" x 3" PC board with 2oz. copper on 4 layers in still air. For a 2 layer board using 1 oz. copper in still air, JA = 204C/W. Note 4: Guaranteed to National's Average Outgoing Quality Level (AOQL). Note 5: Typicals represent the most likely parametric norm. 3 www.national.com LM2734Z/LM2734ZQ Soldering Information Infrared/Convection Reflow (15sec) Wave Soldering Lead Temp. (10sec) Absolute Maximum Ratings (Note 1) LM2734Z/LM2734ZQ Typical Performance Characteristics All curves taken at VIN = 5V, VBOOST - VSW = 5V, L1 = 2.2 H and TA = 25C, unless specified otherwise. Efficiency vs Load Current VOUT = 5V Efficiency vs Load Current VOUT = 3.3V 20130336 20130351 Efficiency vs Load Current VOUT = 1.5V Oscillator Frequency vs Temperature 20130327 20130337 Line Regulation VOUT = 1.5V, IOUT = 500mA Line Regulation VOUT = 3.3V, IOUT = 500mA 20130354 www.national.com 20130355 4 LM2734Z/LM2734ZQ Block Diagram 20130306 FIGURE 1. During the switch off-time, inductor current discharges through Schottky diode D1, which forces the SW pin to swing below ground by the forward voltage (VD) of the catch diode. The regulator loop adjusts the duty cycle (D) to maintain a constant output voltage. Application Information THEORY OF OPERATION The LM2734Z is a constant frequency PWM buck regulator IC that delivers a 1A load current. The regulator has a preset switching frequency of 3MHz. This high frequency allows the LM2734Z to operate with small surface mount capacitors and inductors, resulting in a DC/DC converter that requires a minimum amount of board space. The LM2734Z is internally compensated, so it is simple to use, and requires few external components. The LM2734Z uses current-mode control to regulate the output voltage. The following operating description of the LM2734Z will refer to the Simplified Block Diagram (Figure 1) and to the waveforms in Figure 2. The LM2734Z supplies a regulated output voltage by switching the internal NMOS control switch at constant frequency and variable duty cycle. A switching cycle begins at the falling edge of the reset pulse generated by the internal oscillator. When this pulse goes low, the output control logic turns on the internal NMOS control switch. During this on-time, the SW pin voltage (VSW) swings up to approximately VIN, and the inductor current (IL) increases with a linear slope. IL is measured by the current-sense amplifier, which generates an output proportional to the switch current. The sense signal is summed with the regulator's corrective ramp and compared to the error amplifier's output, which is proportional to the difference between the feedback voltage and VREF. When the PWM comparator output goes high, the output switch turns off until the next switching cycle begins. 20130307 FIGURE 2. LM2734Z Waveforms of SW Pin Voltage and Inductor Current 5 www.national.com LM2734Z/LM2734ZQ applied to the internal switch. In this circuit, CBOOST provides a gate drive voltage that is slightly less than VOUT. In applications where both VIN and VOUT are greater than 5.5V, or less than 3V, CBOOST cannot be charged directly from these voltages. If VIN and VOUT are greater than 5.5V, CBOOST can be charged from VIN or VOUT minus a zener voltage by placing a zener diode D3 in series with D2, as shown in Figure 4. When using a series zener diode from the input, ensure that the regulation of the input supply doesn't create a voltage that falls outside the recommended VBOOST voltage. BOOST FUNCTION Capacitor CBOOST and diode D2 in Figure 3 are used to generate a voltage VBOOST. VBOOST - VSW is the gate drive voltage to the internal NMOS control switch. To properly drive the internal NMOS switch during its on-time, VBOOST needs to be at least 1.6V greater than VSW. Although the LM2734Z will operate with this minimum voltage, it may not have sufficient gate drive to supply large values of output current. Therefore, it is recommended that VBOOST be greater than 2.5V above VSW for best efficiency. VBOOST - VSW should not exceed the maximum operating limit of 5.5V. 5.5V > VBOOST - VSW > 2.5V for best performance. (VINMAX - VD3) < 5.5V (VINMIN - VD3) > 1.6V 20130308 FIGURE 3. VOUT Charges CBOOST 20130309 FIGURE 4. Zener Reduces Boost Voltage from VIN When the LM2734Z starts up, internal circuitry from the BOOST pin supplies a maximum of 20mA to CBOOST. This current charges CBOOST to a voltage sufficient to turn the switch on. The BOOST pin will continue to source current to CBOOST until the voltage at the feedback pin is greater than 0.76V. There are various methods to derive VBOOST: 1. From the input voltage (VIN) 2. From the output voltage (VOUT) 3. From an external distributed voltage rail (VEXT) 4. From a shunt or series zener diode In the Simplifed Block Diagram of Figure 1, capacitor CBOOST and diode D2 supply the gate-drive current for the NMOS switch. Capacitor CBOOST is charged via diode D2 by VIN. During a normal switching cycle, when the internal NMOS control switch is off (TOFF) (refer to Figure 2), VBOOST equals VIN minus the forward voltage of D2 (VFD2), during which the current in the inductor (L) forward biases the Schottky diode D1 (VFD1). Therefore the voltage stored across CBOOST is An alternative method is to place the zener diode D3 in a shunt configuration as shown in Figure 5. A small 350mW to 500mW 5.1V zener in a SOT-23 or SOD package can be used for this purpose. A small ceramic capacitor such as a 6.3V, 0.1F capacitor (C4) should be placed in parallel with the zener diode. When the internal NMOS switch turns on, a pulse of current is drawn to charge the internal NMOS gate capacitance. The 0.1 F parallel shunt capacitor ensures that the VBOOST voltage is maintained during this time. Resistor R3 should be chosen to provide enough RMS current to the zener diode (D3) and to the BOOST pin. A recommended choice for the zener current (IZENER) is 1 mA. The current I BOOST into the BOOST pin supplies the gate current of the NMOS control switch and varies typically according to the following formula: IBOOST = (D + 0.5) x (VZENER - VD2) mA where D is the duty cycle, VZENER and VD2 are in volts, and IBOOST is in milliamps. VZENER is the voltage applied to the anode of the boost diode (D2), and VD2 is the average forward voltage across D2. Note that this formula for IBOOST gives typical current. For the worst case IBOOST, increase the current by 25%. In that case, the worst case boost current will be VBOOST - VSW = VIN - VFD2 + VFD1 When the NMOS switch turns on (TON), the switch pin rises to VSW = VIN - (RDSON x IL), IBOOST-MAX = 1.25 x IBOOST forcing VBOOST to rise thus reverse biasing D2. The voltage at VBOOST is then R3 will then be given by R3 = (VIN - VZENER) / (1.25 x IBOOST + IZENER) VBOOST = 2VIN - (RDSON x IL) - VFD2 + VFD1 For example, let VIN = 10V, VZENER = 5V, VD2 = 0.7V, IZENER = 1mA, and duty cycle D = 50%. Then which is approximately 2VIN - 0.4V IBOOST = (0.5 + 0.5) x (5 - 0.7) mA = 4.3mA for many applications. Thus the gate-drive voltage of the NMOS switch is approximately R3 = (10V - 5V) / (1.25 x 4.3mA + 1mA) = 787 VIN - 0.2V An alternate method for charging CBOOST is to connect D2 to the output as shown in Figure 3. The output voltage should be between 2.5V and 5.5V, so that proper gate voltage will be www.national.com 6 INDUCTOR SELECTION The Duty Cycle (D) can be approximated quickly using the ratio of output voltage (VO) to input voltage (VIN): The catch diode (D1) forward voltage drop and the voltage drop across the internal NMOS must be included to calculate a more accurate duty cycle. Calculate D by using the following formula: 20130348 FIGURE 5. Boost Voltage Supplied from the Shunt Zener on VIN ENABLE PIN / SHUTDOWN MODE The LM2734Z has a shutdown mode that is controlled by the enable pin (EN). When a logic low voltage is applied to EN, the part is in shutdown mode and its quiescent current drops to typically 30nA. Switch leakage adds another 40nA from the input supply. The voltage at this pin should never exceed VIN + 0.3V. VSW can be approximated by: VSW = IO x RDS(ON) The diode forward drop (VD) can range from 0.3V to 0.7V depending on the quality of the diode. The lower VD is, the higher the operating efficiency of the converter. The inductor value determines the output ripple current. Lower inductor values decrease the size of the inductor, but increase the output ripple current. An increase in the inductor value will decrease the output ripple current. The ratio of ripple current (iL) to output current (IO) is optimized when it is set between 0.3 and 0.4 at 1A. The ratio r is defined as: SOFT-START This function forces VOUT to increase at a controlled rate during start up. During soft-start, the error amplifier's reference voltage ramps from 0V to its nominal value of 0.8V in approximately 200s. This forces the regulator output to ramp up in a more linear and controlled fashion, which helps reduce inrush current. OUTPUT OVERVOLTAGE PROTECTION The overvoltage comparator compares the FB pin voltage to a voltage that is 10% higher than the internal reference Vref. Once the FB pin voltage goes 10% above the internal reference, the internal NMOS control switch is turned off, which allows the output voltage to decrease toward regulation. One must also ensure that the minimum current limit (1.2A) is not exceeded, so the peak current in the inductor must be calculated. The peak current (ILPK) in the inductor is calculated by: UNDERVOLTAGE LOCKOUT Undervoltage lockout (UVLO) prevents the LM2734Z from operating until the input voltage exceeds 2.74V(typ). The UVLO threshold has approximately 440mV of hysteresis, so the part will operate until VIN drops below 2.3V(typ). Hysteresis prevents the part from turning off during power up if VIN is non-monotonic. ILPK = IO + IL/2 If r = 0.5 at an output of 1A, the peak current in the inductor will be 1.25A. The minimum guaranteed current limit over all operating conditions is 1.2A. One can either reduce r to 0.4 resulting in a 1.2A peak current, or make the engineering judgement that 50mA over will be safe enough with a 1.7A typical current limit and 6 sigma limits. When the designed maximum output current is reduced, the ratio r can be increased. At a current of 0.1A, r can be made as high as 0.9. The ripple ratio can be increased at lighter loads because the net ripple is actually quite low, and if r remains constant the inductor value can be made quite large. An equation empirically developed for the maximum ripple ratio at any current below 2A is: CURRENT LIMIT The LM2734Z uses cycle-by-cycle current limiting to protect the output switch. During each switching cycle, a current limit comparator detects if the output switch current exceeds 1.7A (typ), and turns off the switch until the next switching cycle begins. THERMAL SHUTDOWN Thermal shutdown limits total power dissipation by turning off the output switch when the IC junction temperature exceeds 165C. After thermal shutdown occurs, the output switch doesn't turn on until the junction temperature drops to approximately 150C. r = 0.387 x IOUT-0.3667 Note that this is just a guideline. The LM2734Z operates at frequencies allowing the use of ceramic output capacitors without compromising transient response. Ceramic capacitors allow higher inductor ripple without significantly increasing output ripple. See the output capacitor section for more details on calculating output voltage ripple. 7 www.national.com LM2734Z/LM2734ZQ Design Guide LM2734Z/LM2734ZQ Now that the ripple current or ripple ratio is determined, the inductance is calculated by: transient is provided mainly by the output capacitor. The output ripple of the converter is: where fs is the switching frequency and IO is the output current. When selecting an inductor, make sure that it is capable of supporting the peak output current without saturating. Inductor saturation will result in a sudden reduction in inductance and prevent the regulator from operating correctly. Because of the speed of the internal current limit, the peak current of the inductor need only be specified for the required maximum output current. For example, if the designed maximum output current is 0.5A and the peak current is 0.7A, then the inductor should be specified with a saturation current limit of >0.7A. There is no need to specify the saturation or peak current of the inductor at the 1.7A typical switch current limit. The difference in inductor size is a factor of 5. Because of the operating frequency of the LM2734Z, ferrite based inductors are preferred to minimize core losses. This presents little restriction since the variety of ferrite based inductors is huge. Lastly, inductors with lower series resistance (DCR) will provide better operating efficiency. For recommended inductors see Example Circuits. When using MLCCs, the ESR is typically so low that the capacitive ripple may dominate. When this occurs, the output ripple will be approximately sinusoidal and 90 phase shifted from the switching action. Given the availability and quality of MLCCs and the expected output voltage of designs using the LM2734Z, there is really no need to review any other capacitor technologies. Another benefit of ceramic capacitors is their ability to bypass high frequency noise. A certain amount of switching edge noise will couple through parasitic capacitances in the inductor to the output. A ceramic capacitor will bypass this noise while a tantalum will not. Since the output capacitor is one of the two external components that control the stability of the regulator control loop, most applications will require a minimum at 10 F of output capacitance. Capacitance can be increased significantly with little detriment to the regulator stability. Like the input capacitor, recommended multilayer ceramic capacitors are X7R or X5R. Again, verify actual capacitance at the desired operating voltage and temperature. Check the RMS current rating of the capacitor. The RMS current rating of the capacitor chosen must also meet the following condition: INPUT CAPACITOR An input capacitor is necessary to ensure that VIN does not drop excessively during switching transients. The primary specifications of the input capacitor are capacitance, voltage, RMS current rating, and ESL (Equivalent Series Inductance). The recommended input capacitance is 10F, although 4.7F works well for input voltages below 6V. The input voltage rating is specifically stated by the capacitor manufacturer. Make sure to check any recommended deratings and also verify if there is any significant change in capacitance at the operating input voltage and the operating temperature. The input capacitor maximum RMS input current rating (IRMS-IN) must be greater than: CATCH DIODE The catch diode (D1) conducts during the switch off-time. A Schottky diode is recommended for its fast switching times and low forward voltage drop. The catch diode should be chosen so that its current rating is greater than: ID1 = IO x (1-D) The reverse breakdown rating of the diode must be at least the maximum input voltage plus appropriate margin. To improve efficiency choose a Schottky diode with a low forward voltage drop. It can be shown from the above equation that maximum RMS capacitor current occurs when D = 0.5. Always calculate the RMS at the point where the duty cycle, D, is closest to 0.5. The ESL of an input capacitor is usually determined by the effective cross sectional area of the current path. A large leaded capacitor will have high ESL and a 0805 ceramic chip capacitor will have very low ESL. At the operating frequencies of the LM2734Z, certain capacitors may have an ESL so large that the resulting impedance (2fL) will be higher than that required to provide stable operation. As a result, surface mount capacitors are strongly recommended. Sanyo POSCAP, Tantalum or Niobium, Panasonic SP or Cornell Dubilier ESR, and multilayer ceramic capacitors (MLCC) are all good choices for both input and output capacitors and have very low ESL. For MLCCs it is recommended to use X7R or X5R dielectrics. Consult capacitor manufacturer datasheet to see how rated capacitance varies over operating conditions. BOOST DIODE A standard diode such as the 1N4148 type is recommended. For VBOOST circuits derived from voltages less than 3.3V, a small-signal Schottky diode is recommended for greater efficiency. A good choice is the BAT54 small signal diode. BOOST CAPACITOR A ceramic 0.01F capacitor with a voltage rating of at least 6.3V is sufficient. The X7R and X5R MLCCs provide the best performance. OUTPUT VOLTAGE The output voltage is set using the following equation where R2 is connected between the FB pin and GND, and R1 is connected between VO and the FB pin. A good value for R2 is 10k. OUTPUT CAPACITOR The output capacitor is selected based upon the desired output ripple and transient response. The initial current of a load www.national.com 8 When planning layout there are a few things to consider when trying to achieve a clean, regulated output. The most important consideration when completing the layout is the close coupling of the GND connections of the CIN capacitor and the catch diode D1. These ground ends should be close to one another and be connected to the GND plane with at least two through-holes. Place these components as close to the IC as possible. Next in importance is the location of the GND connection of the COUT capacitor, which should be near the GND connections of CIN and D1. There should be a continuous ground plane on the bottom layer of a two-layer board except under the switching node island. The FB pin is a high impedance node and care should be taken to make the FB trace short to avoid noise pickup and inaccurate regulation. The feedback resistors should be placed as close as possible to the IC, with the GND of R2 placed as close as possible to the GND of the IC. The VOUT trace to R1 should be routed away from the inductor and any other traces that are switching. High AC currents flow through the VIN, SW and VOUT traces, so they should be as short and wide as possible. However, making the traces wide increases radiated noise, so the designer must make this trade-off. Radiated noise can be decreased by choosing a shielded inductor. The remaining components should also be placed as close as possible to the IC. Please see Application Note AN-1229 for further considerations and the LM2734Z demo board as an example of a four-layer layout. VSW = IOUT x RDSON VD is the forward voltage drop across the Schottky diode. It can be obtained from the Electrical Characteristics section. If the voltage drop across the inductor (VDCR) is accounted for, the equation becomes: This usually gives only a minor duty cycle change, and has been omitted in the examples for simplicity. The conduction losses in the free-wheeling Schottky diode are calculated as follows: PDIODE = VD x IOUT(1-D) Often this is the single most significant power loss in the circuit. Care should be taken to choose a Schottky diode that has a low forward voltage drop. Another significant external power loss is the conduction loss in the output inductor. The equation can be simplified to: PIND = IOUT2 x RDCR The LM2734Z conduction loss is mainly associated with the internal NFET: PCOND = IOUT2 x RDSON x D Switching losses are also associated with the internal NFET. They occur during the switch on and off transition periods, where voltages and currents overlap resulting in power loss. The simplest means to determine this loss is to empirically measuring the rise and fall times (10% to 90%) of the switch at the switch node: Calculating Efficiency, and Junction Temperature The complete LM2734Z DC/DC converter efficiency can be calculated in the following manner. PSWF = 1/2(VIN x IOUT x freq x TFALL) PSWR = 1/2(VIN x IOUT x freq x TRISE) PSW = PSWF + PSWR Typical Rise and Fall Times vs Input Voltage Or VIN TRISE TFALL 5V 8ns 4ns 10V 9ns 6ns 15V 10ns 7ns Another loss is the power required for operation of the internal circuitry: Calculations for determining the most significant power losses are shown below. Other losses totaling less than 2% are not discussed. Power loss (PLOSS) is the sum of two basic types of losses in the converter, switching and conduction. Conduction losses usually dominate at higher output loads, where as switching losses remain relatively fixed and dominate at lower output loads. The first step in determining the losses is to calculate the duty cycle (D). PQ = IQ x VIN IQ is the quiescent operating current, and is typically around 1.5mA. The other operating power that needs to be calculated is that required to drive the internal NFET: PBOOST = IBOOST x VBOOST VBOOST is normally between 3VDC and 5VDC. The IBOOST rms current is approximately 4.25mA. Total power losses are: 9 www.national.com LM2734Z/LM2734ZQ VSW is the voltage drop across the internal NFET when it is on, and is equal to: PCB Layout Considerations LM2734Z/LM2734ZQ Design Example 1: Operating Conditions VIN 5.0V POUT 2.5W VOUT 2.5V PDIODE 151mW IOUT 1.0A PIND 75mW VD 0.35V PSWF 53mW Freq 3MHz PSWR 53mW IQ 1.5mA PCOND 187mW TRISE 8ns PQ 7.5mW TFALL 8ns PBOOST 21mW RDSON 330m PLOSS 548mW INDDCR 75m D 0.568 = 82% Calculating the LM2734Z Junction Temperature RJC = Thermal resistance from chip junction to device case RJA = Thermal resistance from chip junction to ambient air Thermal Definitions: TJ = Chip junction temperature TA = Ambient temperature 20130373 FIGURE 6. Cross-Sectional View of Integrated Circuit Mounted on a Printed Circuit Board. Heat in the LM2734Z due to internal power dissipation is removed through conduction and/or convection. Conduction: Heat transfer occurs through cross sectional areas of material. Depending on the material, the transfer of heat can be considered to have poor to good thermal conductivity properties (insulator vs conductor). Heat Transfer goes as: siliconpackagelead framePCB. Convection: Heat transfer is by means of airflow. This could be from a fan or natural convection. Natural convection occurs when air currents rise from the hot device to cooler air. Thermal impedance is defined as: This impedance can vary depending on the thermal properties of the PCB. This includes PCB size, weight of copper used to route traces and ground plane, and number of layers within the PCB. The type and number of thermal vias can also make a large difference in the thermal impedance. Thermal vias are necessary in most applications. They conduct heat from the surface of the PCB to the ground plane. Four to six thermal vias should be placed under the exposed pad to the ground plane if the LLP package is used. If the Thin SOT23-6 package is used, place two to four thermal vias close to the ground pin of the device. The datasheet specifies two different RJA numbers for the Thin SOT23-6 package. The two numbers show the difference in thermal impedance for a four-layer board with 2oz. copper traces, vs. a four-layer board with 1oz. copper. RJA equals 120C/W for 2oz. copper traces and GND plane, and 235C/W for 1oz. copper traces and GND plane. Thermal impedance from the silicon junction to the ambient air is defined as: www.national.com 10 Design Example 3: Operating Conditions Package SOT23-6 VIN 12.0V POUT 2.475W VOUT 3.30V PDIODE 523mW IOUT 750mA PIND 56.25mW VD 0.35V PSWF 108mW Freq 3MHz PSWR 108mW IQ 1.5mA PCOND 68.2mW IBOOST 4mA PQ 18mW VBOOST 5V PBOOST 20mW TRISE 8ns PLOSS 902mW TFALL 8ns RDSON 400m 2.5W INDDCR 75m D 30.3% Therefore: TJ = (RJC x PLOSS) + TC Design Example 2: Operating Conditions VIN 5.0V POUT VOUT 2.5V PDIODE 151mW IOUT 1.0A PIND 75mW VD 0.35V PSWF 53mW Freq 3MHz PSWR 53mW IQ 1.5mA PCOND 187mW TRISE 8ns PQ 7.5mW TFALL 8ns PBOOST 21mW RDSON 330m PLOSS 548mW INDDCR 75m D 0.568 Using a standard National Semiconductor Thin SOT23-6 demonstration board to determine the RJA of the board. The four layer PCB is constructed using FR4 with 1/2oz copper traces. The copper ground plane is on the bottom layer. The ground plane is accessed by two vias. The board measures 2.5cm x 3cm. It was placed in an oven with no forced airflow. The ambient temperature was raised to 94C, and at that temperature, the device went into thermal shutdown. If the junction temperature was to be kept below 125C, then the ambient temperature cannot go above 54.2C. The second method can give a very accurate silicon junction temperature. The first step is to determine RJA of the application. The LM2734Z has over-temperature protection circuitry. When the silicon temperature reaches 165C, the device stops switching. The protection circuitry has a hysteresis of 15C. Once the silicon temperature has decreased to approximately 150C, the device will start to switch again. Knowing this, the RJA for any PCB can be characterized during the early stages of the design by raising the ambient temperature in the given application until the circuit enters thermal shutdown. If the SW-pin is monitored, it will be obvious when the internal NFET stops switching indicating a junction temperature of 165C. Knowing the internal power dissipation from the above methods, the junction temperature and the ambient temperature, RJA can be determined. TJ - (RJA x PLOSS) = TA The method described above to find the junction temperature in the Thin SOT23-6 package can also be used to calculate the junction temperature in the LLP package. The 6 pin LLP package has a RJC = 20C/W, and RJA can vary depending on the application. RJA can be calculated in the same manner as described in method #2 (see example 3). Once this is determined, the maximum ambient temperature allowed for a desired junction temperature can be found. 11 www.national.com LM2734Z/LM2734ZQ Method 1: To accurately measure the silicon temperature for a given application, two methods can be used. The first method requires the user to know the thermal impedance of the silicon junction to case. (RJC) is approximately 80C/W for the Thin SOT23-6 package. Knowing the internal dissipation from the efficiency calculation given previously, and the case temperature, which can be empirically measured on the bench we have: LM2734Z/LM2734ZQ LLP Package Design Example 4: Operating Conditions The LM2734Z is packaged in a Thin SOT23-6 package and the 6-pin LLP. The LLP package has the same footprint as the Thin SOT23-6, but is thermally superior due to the exposed ground paddle on the bottom of the package. 20130374 No Pullback LLP Configuration RJA of the LLP package is normally two to three times better than that of the Thin SOT23-6 package for a similar PCB configuration (area, copper weight, thermal vias). Package LLP-6 VIN 12.0V POUT 2.475W VOUT 3.3V PDIODE 523mW IOUT 750mA PIND 56.25mW VD 0.35V PSWF 108mW Freq 3MHz PSWR 108mW IQ 1.5mA PCOND 68.2mW IBOOST 4mA PQ 18mW VBOOST 5V PBOOST 20mW TRISE 8ns PLOSS 902mW TFALL 8ns RDSON 400m INDDCR 75m D 30.3% This example follows example 2, but uses the LLP package. Using a standard National Semiconductor LLP-6 demonstration board, use Method 2 to determine RJA of the board. The four layer PCB is constructed using FR4 with 1/2oz copper traces. The copper ground plane is on the bottom layer. The ground plane is accessed by four vias. The board measures 2.5cm x 3cm. It was placed in an oven with no forced airflow. The ambient temperature was raised to 113C, and at that temperature, the device went into thermal shutdown. If the junction temperature is to be kept below 125C, then the ambient temperature cannot go above 73.2C. 20130370 TJ - (RJA x PLOSS) = TA FIGURE 7. Dog Bone For certain high power applications, the PCB land may be modified to a "dog bone" shape (see Figure 7). By increasing the size of ground plane, and adding thermal vias, the RJA for the application can be reduced. www.national.com 12 Maximum junction temperature desired RJA of the specific application, or RJC (LLP or Thin SOT23-6) The junction temperature must be less than 125C for the worst-case scenario. To determine which package you should use for your specific application, variables need to be known before you can determine the appropriate package to use. 1. Maximum ambient system temperature 2. Internal LM2734Z power losses 13 www.national.com LM2734Z/LM2734ZQ 3. 4. Package Selection LM2734Z/LM2734ZQ LM2734Z Design Examples 20130342 FIGURE 8. VBOOST Derived from VIN Operating Conditions: 5V to 1.5V/1A Bill of Materials for Figure 8 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX National Semiconductor C1, Input Cap 10F, 6.3V, X5R C3216X5ROJ106M TDK C2, Output Cap 10F, 6.3V, X5R C3216X5ROJ106M TDK C3, Boost Cap 0.01uF, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.3VF Schottky 1A, 10VR MBRM110L ON Semi D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. L1 2.2H, 1.8A ME3220-222MX Coilcraft R1 8.87k, 1% CRCW06038871F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay www.national.com 14 LM2734Z/LM2734ZQ 20130343 FIGURE 9. VBOOST Derived from VOUT 12V to 3.3V/1A Bill of Materials for Figure 9 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX National Semiconductor C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 6.3V, X5R C3216X5ROJ226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.34VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 0.6VF @ 30mA Diode BAT17 Vishay L1 3.3H, 1.3A ME3220-332MX Coilcraft R1 31.6k, 1% CRCW06033162F Vishay R2 10.0 k, 1% CRCW06031002F Vishay R3 100k, 1% CRCW06031003F Vishay 15 www.national.com LM2734Z/LM2734ZQ 20130344 FIGURE 10. VBOOST Derived from VSHUNT 18V to 1.5V/1A Bill of Materials for Figure 10 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX National Semiconductor C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 6.3V, X5R C3216X5ROJ226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK C4, Shunt Cap 0.1F, 6.3V, X5R C1005X5R0J104K TDK D1, Catch Diode 0.4VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. D3, Zener Diode 5.1V 250Mw SOT-23 BZX84C5V1 Vishay L1 3.3H, 1.3A ME3220-332MX Coilcraft R1 8.87k, 1% CRCW06038871F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay R4 4.12k, 1% CRCW06034121F Vishay www.national.com 16 LM2734Z/LM2734ZQ 20130349 FIGURE 11. VBOOST Derived from Series Zener Diode (VIN) 15V to 1.5V/1A Bill of Materials for Figure 11 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX National Semiconductor C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 6.3V, X5R C3216X5ROJ226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.4VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. D3, Zener Diode 11V 350Mw SOT-23 BZX84C11T Diodes, Inc. L1 3.3H, 1.3A ME3220-332MX Coilcraft R1 8.87k, 1% CRCW06038871F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay 17 www.national.com LM2734Z/LM2734ZQ 20130350 FIGURE 12. VBOOST Derived from Series Zener Diode (VOUT) 15V to 9V/1A Bill of Materials for Figure 12 Part ID Part Value Part Number Manufacturer U1 1A Buck Regulator LM2734ZX National Semiconductor C1, Input Cap 10F, 25V, X7R C3225X7R1E106M TDK C2, Output Cap 22F, 16V, X5R C3216X5R1C226M TDK C3, Boost Cap 0.01F, 16V, X7R C1005X7R1C103K TDK D1, Catch Diode 0.4VF Schottky 1A, 30VR SS1P3L Vishay D2, Boost Diode 1VF @ 50mA Diode 1N4148W Diodes, Inc. D3, Zener Diode 4.3V 350mw SOT-23 BZX84C4V3 Diodes, Inc. L1 2.2H, 1.8A ME3220-222MX Coilcraft R1 102k, 1% CRCW06031023F Vishay R2 10.2k, 1% CRCW06031022F Vishay R3 100k, 1% CRCW06031003F Vishay www.national.com 18 LM2734Z/LM2734ZQ Physical Dimensions inches (millimeters) unless otherwise noted 6-Lead SOT23 Package NS Package Number MK06A 6-Lead LLP Package NS Package Number SDE06A 19 www.national.com LM2734Z/LM2734ZQ Thin SOT23 1A Load Step-Down DC-DC Regulator Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated