TEN40-4812WI - TRACO ELECTRONIC AG

http://www.tracopower.com

Features

◆ High power density: 40W in

2”x2”x0.4” metal package

◆ Ultra wide 4:1 input voltage range

◆ Very high efﬁciency up to 87 %

◆ No minimum load required for

single output models

◆ Over temperature protection

◆ Under voltage lockout

◆ Remote On/Off

◆ Shielded metal case with insulated

baseplate

◆ Optional heat-sink

◆ 3-year product warranty

DC/DC Converters

TEN 40WI Series, 40 Watt

The TEN 40WI series is a family of high performance 40W dc-dc converter modules

featuring ultra wide 4:1 input voltage ranges in a compact low proﬁle case with

industry-standard footprint. A very high efﬁciency allows an operating temperature

range of –40°C to 85°C. Further standard features include remote On/Off, output

voltage trimming, over voltage protection, under voltage lockout, over temperature

and short circuit protection.

Typical applications for these products are battery operated equipment and distrib-

uted power architectures in communication and industrial electronics, everywhere

where isolated, tightly regulated voltages are required and space is limited on the

PCB.

Page 1 of 4

Ordercode Input voltage range Output voltage Output current max. Efﬁciency typ.

TEN 40-2410WI 3.3 VDC 10.0 A 86 %

TEN 40-2411WI 5.0 VDC 8.0 A 87 %

TEN 40-2412WI 9 – 36 VDC 12 VDC 3.35 A 87 %

TEN 40-2413WI (24 VDC nominal) 15 VDC 2.65 A 87 %

TEN 40-2422WI ±12 VDC ±1.65 A 86 %

TEN 40-2423WI ±15 VDC ±1.35 A 86 %

TEN 40-4810WI 3.3 VDC 10.0 A 86 %

TEN 40-4811WI 5.0 VDC 8.0 A 88 %

TEN 40-4812WI 18 – 75 VDC 12 VDC 3.35 A 87 %

TEN 40-4813WI (48 VDC nominal) 15 VDC 2.65 A 87 %

TEN 40-4822WI ±12 VDC ±1.65 A 86 %

TEN 40-4823WI ±15 VDC ±1.35 A 86 %

Models

UL 60950-1

http://www.tracopower.com

Input Specifications

Input current (no load) 24 Vin single output models: 100 mA typ

48 Vin single output models: 60 mA typ

. dual putput models: 30 mA typ

Input current (full load) (nominal input 24/48 VDC) 3.3 VDC models: 1680 / 840 mA typ.

other models: 2000 / 1000 mA typ.

Input voltage variation (dv/dt) 5 V/ms, max.

(complies with ETS300 132 part 4.4)

Start-up voltage / under voltage lockout 24 Vin models: 9 VDC / 8 VDC (typ.)

48 Vin models: 18 VDC / 16 VDC (typ.)

Surge voltage (100 msec. max.) 24 Vin models: 50 V max.

48 Vin models: 100 V max.

EMC characteristics (with external capacitors) see application note: www.tracopower.com/overview/ten40wi

– Conducted noise EN 55022 level A, FCC part 15, level A

– ESD EN 61000-4-2, air: ±8 KV contact: ±6 KV,

perf. criteria A

– Fast transient EN 61000-4-4, ±2 KV, perf. criteria B

– Surge EN 61000-4-5, ±1 KV, perf. criteria A

Output Specifications

Voltage set accuracy (at nominal input and full load) ±1 %

Output voltage adjustment ±10 % (see application note)

Regulation – Input variation Vin min. to Vin max. 0.2 % max.

– Load variation single output models: 0.5 % max. (0 – 100 % load)

dual output models balanced load: 1.0 % max. (4 – 100 % load)

– Load cross variation 25 % / 100 % 5 % max.

Temperature coefficient 0.02 %/K max.

Ripple and noise (20 MHz Bandwidth) 3.3 VDC & 5 VDC output models: 50 mVpk-pk max.

dual outputs: 150 mVpk-pk max.

all other outputs: 75 mVpk-pk max.

Start up time (nominal Vin and constant resistive load) 25 ms typ.

Transient response time (25 % load change) 250 µs typ.

Short circuit protection indefinite (automatic recovery)

Over load protection 150 % of Iout max. typ. foldback

Thermal shutdown @ +110°C typ.

Over voltage protection 3.3 VDC models: 3.9 V

5 VDC models 6.2 V

12/±12 DC m odels: 15 /±15 V

15 VDC output: 18 /±18 V

Minimum load – Single output 12 VDC models: 2% of rated max currrent

15 VDC models: 1.5% of rated max current

other models: not required.

– Dual output ±12 VDC models: 4 % of rated max current on each output

±15 VDC models: 4.5 % of rated max current on each output

(operation at lower load condition will not damage

these converters, however, they may not meet all

listed specifications)

Capacitive load output models 3.3 VDC models: 25’000 µF max.

5.0 VDC models: 13’000 µF max.

12 VDC models: 2’300 µF max.

15 VDC models: 1’500 µF max.

±12 VDC models: 1’200 µF max. (each output)

±15 VDC models: 750 µF max. (each output)

DC/DC Converters

TEN 40WI 40 Watt

Page 2 of 4

http://www.tracopower.com

DC/DC Converters

TEN 40WI 40 Watt

General Specifications

Temperature ranges – Operating –40°C to +85°C

– Case temperature +105°C max.

– Storage –55°C to +125°C

Derating see application note

Humidity (non condensing) 95 % rel H max.

Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >660’000 h

Isolation voltage (60 sec.) – Input / Output 1‘500 VDC

Isolation resistance – Input / Output >1‘000 M Ohm

Isolation capacitance – Input / Output 2500 pF max.

Remote On/Off – On: 3.0 ... 12 VDC or open circuit.

– Off: 0 ... 1.2 VDC or short circuit pin 3 and pin 2

– Off idle current: 2.5 mA max.

Switching frequency (fixed) 300 kHz typ. (Pulse width modulation PWM)

Vibration 10 – 55 Hz, 10G, 30 minutes along X,Y,Z

Safety standards UL 60950-1, IEC/EN 60950-1

Safety approvals – Certification documents www.tracopower.com/overview/ten40wi

Environmental compliance – Reach www.tracopower.com/products/reach-declaration.pdf

– RoHs RoHS Directive 2011/65/EU

Physical Specifications

Casing material copper, nickel plated

Baseplate material none conductive FR4

Potting material epoxy (UL 94V-0 -rated)

Weight 60 g (2.1 oz )

Soldering temperature max. 265°C / 10 sec.

All speciﬁcations valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

Page 3 of 4

Supporting documents: www.tracopower.com/overview/ten40wi

Speciﬁcations can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com

www.tracopower.com

Outline Dimensions

Rev. August 22, 2018

Dimensions in [mm], () = Inch

Pin diameter: 1.0 ±0.05 (0.04 ±0.002)

Pin pitch tolerances: ±0.35 (± 0.014 )

Case tolerances: ±0.5 (±0.02)

Note:

The product label on converter has to be removed before

mounting the heat-sink.

For volume orders converters will be supplied with heat-

sinks already mounted. Please contact factory for quota-

tion.

Page 4 of 4

DC/DC Converters

TEN 40WI 40 Watt

56.0 (2.2) max.

25.2 (0.1)

17.0 (0.67)

max.

Converter

Heat-sink

Thermal pad

Clamp

Order code: TEN-HS3

(cont.: heat-sink, thermal pad, 2 clamps)

Material: Aluminum

Finish: Anodic treatment (black)

Weight: 22 g (0.78oz) (without converter)

Thermal impedance after assembling: 7.6 K/W

Pin Single Dual

1+Vin (Vcc) +Vin (Vcc)

2–Vin (GND) –Vin (GND)

3Remote On/Off

4– Sense* + Vout

5+ Sense* Common

6+ Vout Common

7– Vout – Vout

8Trim

Pin-Out

5.6

10.2

50.8

5.08

27.9

50.8

Bottom

view

45.72

(2.0)

(0.22)

(2.0)

(0.2)

(0.4)

(0.3)

(1.10)

(1.8)

5.08

(0.2)

10.16

(0.4)

7.62 7.625.08

(0.2)(0.3)

5.08 (0.2)

*Sense line to be connected to the output

either at the module or at the load under

regard of polarity.

Heat-Sink (Option)