M4Z28-BR00SH M4Z32-BR00SH ZEROPOWER(R) SNAPHAT(R) (Battery) FEATURES SUMMARY PROVIDES BATTERY BACKUP POWER FOR NON-VOLATILE ZEROPOWER and SUPERVISOR DEVICES IN THE 28-PIN SNAPHAT SOIC PACKAGE REMOVABLE BATTERY AVOIDS HEAT ASSOCIATED WITH SURFACE-MOUNT PROCESS SNAPS DIRECTLY ONTO SURFACEMOUNTED SNAPHAT SOIC Figure 1. SNAPHAT Top Package SNAPHAT (SH) Battery CHOICE OF BATTERY CAPACITIES - M4Z28-BR00SH = 48mAh - M4Z32-BR00SH = 120mAh KEYED INSERTION TO INSURE PROPER ASSEMBLY REMOVABLE FOR REPLACEMENT and PROPER DISPOSAL AVAILABLE IN TUBES OR TAPE & REEL August 2002 1/12 M4Z28-BR00SH, M4Z32-BR00SH TABLE OF CONTENTS SUMMARY DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Logic Diagram (Figure 2.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Signal Names (Table 1.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 MAXIMUM RATING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Absolute Maximum Ratings (Table 2.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DC AND AC PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operating and AC Measurement Conditions (Table 3.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SNAPHAT Insertion/Extraction Forces (Figure 3.) . Battery Characteristics . . . . . . . . . . . . . . . . . . . . . . UL Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Discharge Rates (Figure 4.) . . . . . . . . . . . . DIP Extractor Tool (Figure 5.) . . . . . . . . . . . . . . . . . ....... ....... ....... ....... ....... ....... ....... ...... ...... ...... ...... ...... ...... ...... ....... ....... ....... ....... ....... ....... ....... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... .....5 .....6 .....6 .....6 .....6 .....7 .....7 PART NUMBERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PACKAGE MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 REVISION HISTORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2/12 M4Z28-BR00SH, M4Z32-BR00SH SUMMARY DESCRIPTION The M4ZXX-BR00SH SNAPHAT(R) top is a detachable lithium power source for ST's nonvolatile ZEROPOWER (R) surface-mount SOIC (MH) package (28-pin). Figure 2. Logic Diagram The SNAPHAT top contains a lithium battery and is designed to be "snapped on" after the SOIC is surface mounted on the PC board. The two-piece solution prevents the battery from being exposed to the high temperatures of the surface mount process. Table 1. Signal Names VBAT- Negative Voltage VBAT+ Positive Voltage SNAPHAT VBAT- VBAT+ AI02525 3/12 M4Z28-BR00SH, M4Z32-BR00SH MAXIMUM RATING Stressing the device above the rating listed in the "Absolute Maximum Ratings" table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 2. Absolute Maximum Ratings Symbol TA TSTG Parameter Value Unit Ambient Operating Temperature -40 to 85 C Storage Temperature (VCC Off, Oscillator Off) -40 to 85 C CAUTION: Do NOT wave solder SOIC to avoid damaging SNAPHAT sockets. DC AND AC PARAMETERS This section summarizes the operating and measurement conditions, as well as the DC and AC characteristics of the device. The parameters in the following DC and AC Characteristic tables are derived from tests performed under the Measure- ment Conditions listed in the relevant tables. Designers should check that the operating conditions in their projects match the measurement conditions when using the quoted parameters. Table 3. Operating and AC Measurement Conditions Parameter M4Z28-BR00SH M4Z32-BR00SH Unit Nominal Battery Voltage (VCC) 2.8 2.8 V Nominal Battery Capacity 48 120 mAh Li(CF) Li(CF) Battery Chemistry 4/12 M4Z28-BR00SH, M4Z32-BR00SH MECHANICAL INFORMATION Electrical connection to the SOIC is made through two pins that connect to the press fitted sockets at one end of the SOIC. Critical contact points between the pins and sockets are gold-plated to resist oxidation. Internally, each socket contains six independent contact fingers to form redundant connections between the two components. These sockets were designed to provide high point contact force to provide the lowest possible contact resistance. The SNAPHAT(R) top also incorporates four molded-in retaining clips which hold onto the ends of the SOIC insuring mechanical and electrical connection even under severe mechanical shock and vibration. The combined SOIC and SNAPHAT assembly can sustain shock levels in excess of 100 g without separating. This package also passes variable frequency testing in accordance with MIL-STD-883, method 2007.2, condition A. Figure 3 illustrates the affect of repeated insertion and extraction of the SNAPHAT top to the SOIC. The force required to extract the SNAPHAT, and then to re-insert it, reduces each time. After four or five extractions, the reduction starts to become unnoticeable and the force required remains at a fairly constant figure. Typically, though, the SNAPHAT will only need to be extracted and reinserted once in its lifetime. Figure 3. SNAPHAT Insertion/Extraction Forces 15 12.5 Average Insertion Average Extraction Force (pounds) 10 7.5 5 2.5 0 1 2 3 4 5 6 7 8 9 10 Number of Extractions AI02526 5/12 M4Z28-BR00SH, M4Z32-BR00SH Battery Characteristics Figure 4, page 7 illustrates the lithium coin cell discharge rate for a given load. This demonstrates the characteristically flat voltage level supplied by the battery until very near the end of its life. These discharge levels have been greatly accelerated in comparison to the normal, actual usage. Note: These batteries contain no Mercury (Hg), Cadmium (Cd), or Lead (Pb). UL Recognition The M4ZXX-BR00SH has been recognized by Underwriters Laboratories under their Component Recognition Program and carries U.L. File Number E89556. Battery Life For information on Data Retention Life and Battery Storage Life, please refer to the Application Note AN1012. General Notes ST has conducted experiments using a manual press which determined that if approximately 60 6/12 pounds of force is applied to the top of the SNAPHAT(R), battery damage and/or die cracks could be induced. As Figure 3, page 5 specifies, only an average of less than 13 force-pounds is required for proper insertion. We recommend that no more than 40 pounds of force be applied during SNAPHAT insertion. If a manual press in employed, it is very important that it be calibrated such that it cannot exceed this limit. To remove the SNAPHAT(R) top for replacement, a DIP/IC extractor tool should be used (see Figure 5). The SNAPHAT top should be grabbed by the narrow end to avoid bending the pins. Caution: To avoid draining battery do NOT place SNAPHAT pins into conductive foam. Caution: To avoid damaging SNAPHAT sockets do NOT wave solder SOIC. For battery disposal information, see on the web at www.rayovac.com. M4Z28-BR00SH, M4Z32-BR00SH Figure 4. Battery Discharge Rates LOAD CHARACTERISTICS 3.5 Temp: 20C Voltage (V) 3.0 2.5 BR1225 2.0 15k 30k 100k 1.5 1.0 0 200 400 600 800 1000 1200 1400 1600 1800 2000 Duration (hrs.) (A) LOAD CHARACTERISTICS 3.5 Temp: 20C Voltage (V) 3.0 2.5 BR1632 2.0 15k 30k 50k 100k 1.5 1.0 0 1000 2000 3000 4000 Duration (hrs.) (B) 5000 6000 AI02519 Figure 5. DIP Extractor Tool AI02527 7/12 M4Z28-BR00SH, M4Z32-BR00SH PART NUMBERING Table 4. Ordering Information Scheme Example: M4Z 28-BR00 SH 1 TR Device Type M4Z Battery Voltage and Capacity 28-BR00 = BR1225, 3V, 48mAh 32-BR00 = BR1632, 3V, 120mAh Package SH = SNAPHAT(R) Temperature Range 1 = -40 to 85C Shipping Method blank = Tubes TR = Tape & Reel For a list of available options (e.g., Speed, Package) or for further information on any aspect of this device, please contact the ST Sales Office nearest to you. 8/12 M4Z28-BR00SH, M4Z32-BR00SH PACKAGE MECHANICAL INFORMATION Figure 6. SH - 4-pin SNAPHAT Housing for 48mAh Battery Package Outline A1 eA A2 A A3 B L eB D E SHZP-A Note: Drawing is not to scale. Table 5. SH - 4-pin SNAPHAT Housing for 48mAh Battery Package Mechanical Data mm inches Symb Typ Min A Max Typ Min 9.78 Max 0.385 A1 6.73 7.24 0.265 0.285 A2 6.48 6.99 0.255 0.275 A3 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 14.22 14.99 0.560 0.590 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 9/12 M4Z28-BR00SH, M4Z32-BR00SH Figure 7. SH - 4-pin SNAPHAT Housing for 120mAh Battery Package Outline A1 eA A2 A A3 B L eB D E SHZP-A Note: Drawing is not to scale. Table 6. SH - 4-pin SNAPHAT Housing for 120mAh Battery Package Mechanical Data mm inches Symb Typ Min A Typ Min 10.54 Max 0.415 A1 8.00 8.51 0.315 0.335 A2 7.24 8.00 0.285 0.315 A3 10/12 Max 0.38 0.015 B 0.46 0.56 0.018 0.022 D 21.21 21.84 0.835 0.860 E 17.27 18.03 0.680 0.710 eA 15.55 15.95 0.612 0.628 eB 3.20 3.61 0.126 0.142 L 2.03 2.29 0.080 0.090 M4Z28-BR00SH, M4Z32-BR00SH REVISION HISTORY Table 7. Document Revision History Date Rev. # Revision Details November 1999 1.0 First Issue 05/29/01 2.0 Reformatted 06/04/01 2.1 Basic textual changes from reformatting activity 07/10/01 2.2 Remove references to "Crystal;" change references to "SUPERVISOR" from Controller; clarify temperature characteristics 01/21/02 2.3 Change to include Crystal Accuracy (Table 3); add text for SNAPHAT insertion force tolerance and battery characteristics note 08/20/02 2.4 Update Insertion/Extraction Forces (Figure 3) 11/12 M4Z28-BR00SH, M4Z32-BR00SH Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics All other names are the property of their respective owners. (c) 2002 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. www.st.com 12/12