Weller Zero-Smog Filter Systems (R) The Weller Zero-Smog Systems put an end to air pollution caused by soldering, adhesives and laser work. In all of these applications fumes or fine particles are released into the work place atmosphere which are hazardous to staff exposed to them. The Weller Zero-Smog Systems' combination of Pumps, electronic controls and filters removes this hazard. Tip Extraction Volume Extraction Weller FE soldering irons have an integral smoke tube mounted in the handle of the iron which when soldering is positioned directly above the joint to collect any fumes generated. Fume extraction irons can be connected to Weller Zero-Smog systems WFE, WFEP bench mounted units driving upto 2 irons or WFE 20 mobile unit driving upto 20 irons. Fume extraction attachments can be retro fitted to non fume extraction Weller soldering irons. For applications where Volume extraction is more suitable, e.g. solder baths, hot air soldering, micro solders and gluing work, Weller offers the mobile systems WFE 2S and WFE 4S. The units purify the air at up to 8 workplaces. A wide range of accessories is available for each mobile system. 2 Zero-Smog Filter System Weller Zero-Smog Systems have a three stage filter system for removing fine particles, fumes and gases produced in assembly operations. Filters to meet varying work place requirements are available. The main areas where filtration is required are * Solder /flux fumes * Adhesive fumes * Pollutants resulting from laser applications Fine dust filter as per DIN 24185 / EN 779 Filter class medium filtration efficiency (dust) Am % medium filtration efficiency (aerosols) Em % Application F5 F7 > 97 > 98 40 - 60 80 - 90 F9 > 99 > 95 for standard applications for applications with high flux content with pollution gases with high solids content e.g. soldering work with enamel-covered wire or laser tasks HEPA filter DIN 24184, 24183 / EN 779 HEPA (High Efficiency Particulate Air) Filter Filter class Filtration efficiency % Application H13 > 99.95 Filter for ultra-clean rooms 1000-100 Filter process 1. Fine dust filter For standard applications with little flux up to pollution gases with high solids content. Weller offers the filter classes F5, F7 and F9. 2. HEPA filter Filters particles up to 0.3 m. Weller offers HEPA (High Efficiency Particulate Air) filters of class H13, medium filtration efficiency 99.95 %. WFE / WFE P 2.+3. 3. Wide band gas filter For cleaning harmful fumes and vapours. The Weller wide band filter consists of 50 % active carbon and 50 % Puratex. Harmful gases with a high molecular weight are cleaned by the active carbon. Puratex is suitable for absorbing gases of lower molecular weight. Because of its composition, Puratex is able to convert a large number of chemical pollutants by means of molecular modification into non-polluting gases. 4. Gas filter (option) The gas filter is used for extracting adhesive fumes and solvents. Experience has shown that filtering suspended particles is not so vital in this respect. The gas filter is filled with 50 % active carbon and 50 % Puratex. The HEPA H 13 is omitted. WFE 20D WFE 2S / WFE 4S 1. 1. 2.+3. 2.+3. or 4. 1. 3 Weller(R) Zero-Smog Extraction Systems for all tasks Tip Extraction Characteristics With this option using a FE soldering iron fumes are extracted directly at the soldering tip. See page 8 for the range of Weller FE irons and attachments. General properties * High vacuum, upto 12,000 Pa * Low volume * Maximum bridging distance 200 m (WFE 20D requires Weller pipe system 50) Applications * Hand soldering * Small solder baths Special features * Stop + Go supports to switch the extraction system on when the FE iron is removed from the support and off after a short delay when the iron is replaced (WFE & WFE P only) * Variable electronically controlled pump speed, adjustable at the unit or by remote control via RS 232 and PC (WFE 20D) * Filter condition warning, by LED at the unit or remote via RS 232 and PC (WFE 20D) Units WFE 20D WFE WFE P Number of work places 20 2 System structure central + stand alone 4 central Weller extraction systems are specifically designed for continuous operation in industry. The high quality of manufacture, care taken in the design stage and component choice have given Weller machines a world wide reputation for reliability and longevity. Volume extraction Characteristics For applications where extraction over a wide area is required General properties * Low vacuum upto 2,800 Pa * High volume * Max bridging distance 30 m ( WFE 4S using Weller pipe system 75) Areas of application * * * * Hot air workplaces Soldering machines, robots, solder baths Laser processing Adhesive fumes * Clean room applications * microscope workplaces Special features * automatic speed control depending on the number of connected workplaces * the units can be remotely controlled by means of a remote control system available as an accessory or by a PC/PLC connection * filter condition monitoring at the unit or by remote control (accessories) Units WFE 2S WFE 4S Number of work places 4 8 System structure central central + stand alone 5 Tip Extraction Extraction Units r : es fo New er stag ion t w 2 Po r extrac ith w e h e c g ns. hi an orm ring iro f r e e p sold 2 FE WFE WFE P WFE - Small, portable, quiet, compressed air driven, for stand alone application. WFE P - small, portable, quiet, electrically driven, for central application The Weller WFE is a small, portable unit designed for soldering fume extraction with up to two FE soldering irons. The WFE requires clean and oil-free compressed air. The vacuum is generated by a maintenance-free compressed air converter. The contaminated air is purified by a prefilter and main filter system. The pre filter consists of a fine dust filter F7. The compact main filter cartridge consists of a wide band gas filter (50% active carbon, 50% Puratex) and a HEPA filter of class H13. A compressed air cleaning filter removes additional odours caused by the compressed air. This highly efficient filter system makes the WFE a genuine air recovery system. The filter-lift system allows fast and convenient replacement of the filter cartridge. The FE soldering irons are connected directly to the unit - additional leads are not required. The Weller WFE P is soldering fume extraction unit runs with line voltage for one or two FE soldering irons. In contrast to the WFE, an electric, long-life and optimally soundproofed vacuum pump guarantees the required vacuum, this making the WFE P independent of compressed air. The vacuum pump has two power stages, which can be set by means of rocker switches according to the number of connected FE soldering irons. This saves energy. The motor is maintenance-free and has a thermal over load to protect the unit. The WFE P has a three stage filter system comprising a F7 grade fine dust filter, and main filter consisting of a wide band gas filter (50% active carbon and 50% puratex) and a HEPA class 13 fine particle filter. The Filter lift system allows fast and convenient main filter replacement. FE irons are connected directly to unit additional leads are not required. Technical data WFE: Height 200 mm Diameter 140 mm Weight 2,7 kg Operating pressure 3,5 - 6 bar Air consumption 30 l/min Sound level 39 db(A) at 1 m distance Max. vacuum max. 20.000 Pa Max. capacity 2 FE-soldering irons Order No.: 005 36 402 99 Spare filter for WFE: * Compressed air005 87 357 57 cleaning filter * Compact filter 005 36 410 99 consists of: - HEPA filter (H13) - Wide band gas filter (50 % active carbon, 50 % Puratex) Top Oben * Fine dust filter (F7) (3 pieces) 005 36 421 99 Technical data WFE P: Height 295 mm Diameter 140 mm Weight 4 kg Operating voltage 230 V / 50 Hz Power input 50 W Sound level 45 db(A) at 1 m distance Max. vacuum 30,000 Pa Max. capacity 2 FE soldering irons Order No.: 005 36 386 99 (UK: 005 36 383 99) Spare filter for WFE P: * Compact filter 005 36 410 99 consists of: - HEPA filter (H 13) - Wide band gas filter (50 % active carbon, 50 % Puratex) Top Oben * Fine dust filter (F7) 005 36 421 99 (3 pieces) Accessories for WFE and WFE P For FE soldering irons and Stop + Go supports, see pages 8/9. Installation option see page 10. 6 WFE 20D lled ntro o c : New onically tr r Elec e. 2 fo in b S 23 r R tu e ol. rfac Inte te contr o rem WFE 20D - mobile, powerful, electronically controlled, for central or stand alone application The WFE20D is designed for tip extraction applications. Upto 5 Weller FE soldering irons can be connected directly; indirectly, via pipe system 50 available as an accessory: up to 20 FE soldering irons. The powerful maintenance-free turbine generates a vacuum of 12.000 Pa and is electronically controlled. The operating hours and the level of filter contamination are also recorded electronically. The filter system has three stages. It comprises a fine dust filter F5 and a compact filter, consisting of a HEPA filter H13 and a wide band gas filter (50 % active carbon, 50 % Puratex). The filter system achieves a filtration rate of 99.95 % as per EN 1822 with a particle size of 0.12 m. Technical data WFE 20D: Dimensions (LxWxH): 450 mm x 450 mm x 695 mm Weight: 45 kg Operating voltage: 230 V Power input: 630 VA Sound level: 51 dB(A) Max. vacuum: 12,000 Pa Max. delivery rate: 100 m3/h Max. capacity: 20 FE soldering iron Order No.: 005 36 476 99 (UK: 005 36 473 99) Further features: * Two selectable operating modes: - Mode 0: vacuum regulated to 12,000 Pa - Mode 1: extraction performance can be set individually between 20 % - 100 % with the buttons * Electronic filter check (LED) through differential pressure measurement. If the specified degree of contamination is exceeded, the unit switches off. * Electronic filter operation status display. For better management of the filter change intervals, the filter operating hours can be pre-specified. The necessary filter change is indicated in good time, thus optimising filter procurement and replacement. * Interface RS 232 for remote monitoring or remote control. * With the remote control, available as an accessory, the following functions can be controlled: - Switching the unit on/off - Speed setting (only in mode 1) - Filter status display Spare filters WFE 20D:* * Fine dust filter (F5) 005 87 358 37 (F7) 005 87 358 36 * Compact filter 005 87 358 38 Consists of: - HEPA filter (H 13) - Wide band gas filter (50% active carbon, 50 % Puratex) Accessories WFE 20D: For FE soldering irons and Stop + Go supports, see pages 8/9. For other accessories, see page 10/11. For pipe system 50, see page 18. 7 Tip Extraction Accessories FE Soldering Irons Weller FE soldering irons are specifically designed for tip extraction applications. The smoke tube is integral with the handle and is normally placed over the joint when soldering but can be retracted when access to the joint is a problem and can be removed for cleaning. The irons are temperature controlled, ergonomic and allow precise handling. The electronically controlled irons can be driven from any PU /PUD series power unit compatible with the rating of the iron or any rework station. FE 50M irons can only be driven from the P51 power unit. The range of iron power ratings and the extensive range of solder tips mean that there is an iron to suit all applications. The FE irons are supplied with a 5 mm-dia. burn proof hose 2.5 m long, all handles leads and hoses are ESD safe. Model / Description Support Order No. FE 50 Soldering pencil 50 W FE 50 Soldering iron set with safety rest KH 20 AK 20, KH 20* 005 25 153 99 005 33 150 99 FE 50M Soldering pencil with Magnastat control system 50 W AK 20, KH 20* 005 32 152 99 FE 75 Soldering iron 80 W FE 75 Soldering iron set with safety rest KH 20 AK 20, KH 20* 005 29 166 99 005 33 151 99 WSP 80 FE Soldering pencil 80 W WPH 80 005 29 162 99 FE 80 Soldering iron 80 W AK 20, KH 20* 005 26 162 99 * Fume extraction funnels specific to FE irons are included in the scope of supply of the soldering irons for use with KH20 and KH 23 bench supports. FE attachments A range of FE attachments are available to fit to Weller soldering and desoldering irons to convert standard products to fume extraction versions. The attachments are Model / Description Required Support Order No. For WSP 80 Soldering pencil For WMP Soldering pencil For MLR 21, MLR 80 Soldering pencil For LR 21, LR 82, TCP S Soldering iron For W 61, W 101, WSP 150 Soldering iron For WSF 80D5/8 Soldering tin feed system For DS 22, DS 80, DSX 80 Desoldering iron WPH 80 WPHM WPH 80 AK 20 AK 1 AK S (included) AK 20 005 29 167 99 005 29 177 99 005 29 127 99 005 25 125 99 005 25 125 99 005 28 126 99 005 13 125 99 Locking clip The locking clip is used to disconnect FE soldering irons that are not required so that extraction power is not lost unnecessarily. The clip can be operated quickly and conveniently. Order No.: 005 36 352 99 8 supplied with all necessary fittings and hoses. The performance of the retrofitted tools is not affected. Extraction hose (spare) Heat-resistant silicone hose, o 5 mm for all FE soldering irons (sold by metre) ) Order No.: 005 25 410 00 Supports and holders for FE soldering irons AK 20 KH 20* KH 23* WPH 80 Support for FE 50, FE 50M, FE 75, FE 80 Support for FE 50, FE 50M, FE 75, FE 80 with FE attachment: LR 21, LR 82, TCPS 005 15 020 99 Support for FE 25, MLR 21FE Support for WSP 80FE with FE attachment: MLR 21, WSP 80 005 15 023 99 005 15 140 99 005 15 030 99 * Fume extraction funnels specific to FE irons are included in the scope of supply of the soldering irons for use with KH20 and KH 23 bench supports Stop + Go supports for FE soldering irons together with WFE and WFE P and when the FE iron is replaced in the bench support, The Weller Stop + Go supports are recommended accesafter a short delay to gather the fumes from any solder sories for FE irons using the WFE or WFE P extraction on the tip it switches the unit off. This reduces running units. A fibre optic sensor switches the extraction unit on costs. when the FE iron is removed from the bench support FE soldering irons Basic unit Stop + Go and a support with fibre optic sensor for: WFE (pneumatic) for: WFE P (electric) 2. support with fibre optic sensor for extending the Stop + Go basic unit for 2 workplaces FE 25 FE 50 FE 50M FE 75 FE 80 KHP 005 15 086 99 KHE 005 15 076 99 KHE / P 005 15 080 99 WSP 80FE KHP 80 005 15 084 99 KHE 80 005 15 083 99 KHE / P 80 005 15 141 99 Cord support The cord support keeps the cord of the soldering iron out of the direct working area. This allows an easy handling of the soldering iron. Especially recommended for use with FE soldering irons. Modello / Descrizione Spring holder for AK 20 Spring holder for KH 23 Codice articolo 005 15 065 99 005 15 066 99 9 Tip Extraction Accessories Installation option for a central system with WFE P KH E Stop + Go-support WDD 161V WFE P soldering iron desoldering iron Installation option for a central and stand alone system with WFE 20D central system stand alone system with pipe system 50 upto ca. 200 m right angle pipe 50 005 36 322 99 extraction hose 5 mm > 2,5 m bis max. 10 m 005 25 410 00 WSD 81 connecting element 40-50 005 36 415 99 WMD 3 pipe 50 005 36 323 99 double socket 50 005 36 319 99 connecting element 40-50 005 36 415 99 T-piece 50 005 36 344 99 pipe 50 005 36 323 99 connecting nipple for extraction hose 5 mm 005 36 338 99 branch 50 005 36 321 99 pipe clamps 50 005 36 329 99 connecting nipple for hose 17 005 36 358 65 end seal 50 005 36 324 99 pipe 50 005 36 323 99 end seal 50 005 36 324 99 ESD SAF E extraction hose 40 005 36 414 00 extension hose 17 005 36 326 99 adapter 17 005 36 343 99 WFE 20D RS 232 cable (2 m) 005 31 191 99 remote control 005 87 359 09 10 Accessories for tip extraction Description Order No. Extraction hose 40,1 m, o 40 mm dia., complete. With 2 connecting elements for direct connection of unit (WFE 20D) to pipe system 50, plastic, grey/black, flexible. 005 36 316 99 Extraction hose 40, o 40 mm dia. without connecting elements (sold by metre), plastic, grey/black, flexible. 005 36 414 00 Connecting element 40-50 for connecting extraction hose 40 and pipe system 50, rubber, black. 005 36 415 99 17 mm dia. x 5 m long extension hose. Used where the fume extraction iron is further than 2.5 m from the pipe system 50. Note connection nipple for hose 17 and adapter 17 will be required, plastic, transparent. 005 36 326 99 Connection nipple for hose 17. Amend direction to read direct. 005 87 358 65 Nut G 3/8" for connection nipple. 005 87 358 66 Adapter 17. Adapts 17 mm dia hose to 5 mm dia hose on FE iron. 005 36 343 99 Connection nipple for 5 mm dia extraction hose to connect FE irons directly directly to pipe system 50. The connection nipple is screwed at any point into the pipe system. 005 36 338 99 Amend cap closure to Dust cap. 005 87 350 50 11 Volume Extraction Extraction Units WFE 2S WFE 2 Kit 1 WFE 2S - small, portable, quiet with electronic speed control, for centralised applications. The Weller WFE 2S extraction unit purifies the air at up to two workplaces. It is designed as a central system directly at the workplace. A powerful, maintenance-free pump provides continuous fume extraction at a maximum air extraction rate of 230 m3/h. A built-in microprocessor controls the adjustable pump speed. This avoids unnecessary waste of suction power and saves energy. The three-stage filter system is included in the scope of delivery and can be replaced easily. It comprises a fine dust filter (F5) and a combined HEPA filter and wide band gas filter. The WFE 2S extraction unit is supplied with a pipe connecting element 50 for the extraction hose 50. The extensive range of accessories, such as extraction nozzles and hoods, allows versatile and flexible use of the system. Features: * Speed set by rotary potentiometer * Red/Green LED to indicate filter condition * RS 232 interface for remote control via PC WFE 2 K1 / K2 Stand alone extraction systems for one or two work places. The tried and tested Weller WFE 2S fume extraction system is available in two user friendly, stand alone systems. Designed for use in industrial, service and laboratory applications these units are supplied complete with flexible hoses, extraction arms, mounting brackets and system seals, ready for installation in situe. Additional extraction arms with other extraction nozzles, extraction hoods and plates are available as optional extras. All arms hoses and hoods are ESD safe. Technical data WFE 2S: Dimensions: 320 x 320 x 395 (L x W x H mm) Weight: 19 kg Operating voltage: 230 V Power input: 275 VA Sound level: 48 db(A) in 1 m distance Max. vacuum: 2.700 PA Max. extraction rate: 230 m3/h Max. capacity: 2 work places Standard connection: pipe system 50 Order No.: 005 36 266 99 (UK: 005 36 363 99) WFE 2S with gas filter as above but with adhesive fume filter Order No.: 005 36 466 99 (UK: 005 36 463 99) 12 Spare filters for WFE 2S: * Fine dust filter (F5) 005 87 358 84 (10 units) (F7) 005 87 358 85 * Compact filter 005 87 358 83 consists of: - HEPA filter (H13) - Wide band gas filter (50% active carbon, 50% Puratex) * Option: adhesive fume 005 87 358 95 filter (50 % active carbon, 50 % Puratex without HEPA filter H13) WFE 2 Kit 2 WFE 2 Kit 1 (for one work station) consists of: * 1 Solder fume extraction unit WFE 2S * 1 Extraction arm with niozzle WFAN 50 flexible, 50 mm dia. * 1 Bench mounting bracket WFTB 50 * 1 System seal WFFMP 50 * 1 Extraction hose 50 mm dia x 3 m long (005 87 353 27) Order No.: 005 36 436 99 (UK: 005 36 433 99) WFE 2 Kit 2 (for two work stations) consists of: * 1 Solder fume extraction unit WFE 2S * 2 Extraction arm with nozzle WFAN 50, flexible, 50 mm dia. * 2 Bench bench mounting brackets WFTB 50 * 2 System seals WFFMP 50 * 2 Extraction hoses 50, 3 m, o 50 mm (005 87 353 27) * 1 Hose connector 50 (005 87 358 47) Order No.: 005 36 456 99 (UK: 005 36 453 99) WFE 2 Kit 1 with gas filter as above but with adhesive fume filter Order no.: 005 36 446 99 (UK: 005 36 443 99) WFE 2 Kit 2 with gas filter as above but with adhesive fume filter Order No.: 005 36 486 99 (UK: 005 36 483 99) WFE 4S WFE 4S - mobile, powerful, electronically controlled suitable for central or stand alone applications. The WFE 4S is able to extract fumes from up to 8 workstations. The powerful maintenance free variable speed pump is electronically controlled, and has a maximum capacity of 615m3/h. It has 3 operating modes. Standard speed control selected by the user irrespective of the load on the system. Speed limiting control, when the pump speed is automatically varied to match the load on the system and Economy control, when the rate of fume absorption is maintained at a constant value. The operating hours and the filter condition is also recorded. A three-stage filter comprising a fine dust filter (F5), HEPA filter and wide band gas filter is fitted to the standard unit but an adhesive fume absorption filter can be fitted. A flanged connecting pipe suitable for connection to the Weller pipe system 75 is supplied. A wide range of system 75 pipes, fittings and accessories are available to meet all installations and applications. Features: * 3 operating modes * LED display for filter condition indication * RS 232 interface for remote control via a PC Technical data WFE 4S: Dimensions: 450 x 450 x 650 mm (L x W x H) Weight: 21 kg Operating voltage: 230 V/ Hz Power input: 450 VA Noise level: 51 db(A) at 1 m distance Max. vacuum: 2,800 Pa Max. extraction rate: 615 m3/h Max. capacity: 8 work places Standard connection: pipe system 75 Order No.: 005 36 256 99 (UK: 005 36 253 99) WFE 4S with gas filter: as above but with adhesive fume filter Order No.: 005 36 496 99 (UK: 005 36 493 99) Spare filter + special filter for WFE 4S: * Fine dust filter (F5) 005 87 358 37 (10 units) (F7) 005 87 358 36 * Compact filter 005 87 358 38 consists of: - HEPA filter (H13) - Wide band gas filter (50% active carbon, 50% Puratex) Pre Filter To extend capacity of WFE 2S and WFE 4S units. The pre filter is recommended for use with solderbath , automatic soldering and laser applications. It acts as a first stage in the filter process thereby increasing the lifetime of the main filter units. The pre filter can be fixed directly to the top of the WFE 4S or in series with it or the WFE 2S as an integral element of the extraction system Scope of supply: * Filter box * Fine dust filter (F7) 005 87 358 60 * 2 x hose 005 87 358 32 connections 75 Order No.: 005 87 358 62 * Special filter (option): adhesive fume filter 005 87 358 35 (50 % active carbon, 50 % Puratex without HEPA filter H13) 13 Volume Extraction Accessories Installation option for a central system with WFE 2S extraction arm WFAF 50 005 36 372 99 hose clamp 50-70 005 87 358 79 extraction hose 50 005 87 353 27 system seal WFFMP 50 005 36 371 99 hose connection 50 005 87 358 47 bench mounting bracket WFTB 50 005 36 379 99 hose connection 50 90 005 87 358 48 WHA 3000P system seal WFFMP 50 005 36 371 99 WSB 150 extraction hose 50 005 87 353 27 exhaust hood WFCC50 005 36 378 99 WFE 2S RS 232 cable (2 m) 005 31 191 99 remote control 005 87 359 09 Installation option for a central and stand alone system with WFE 4S y y with pipe system 75 upto ca. 30 m extraction hose 50 005 87 353 27 hose clamp 50-70 005 87 358 79 extraction hose 75 005 87 353 13 hose connection 50 005 87 358 47 pipe 75 005 87 358 70 T piece 75 005 87 358 71 hose connection 75 90 005 87 358 33 right angle pipe 75 005 87 358 69 adapter 50-75 005 87 358 56 pipe clamps 75 005 87 358 64 hose clamp 70-90 005 87 358 31 adapter 50-75 005 87 358 56 extraction hose 50 005 87 353 27 WFE 4S T piece 75 005 87 358 71 system seal WFFMP 50 005 36 371 99 extraction hose 50 005 87 353 27 extraction arm with articulated joint 005 87 358 49 WFE 4S RS 232 cable (2 m) 005 31 191 99 remote control 005 87 359 09 end seal 75 005 87 358 55 system seal WFFMP 50 005 36 371 99 extraction plate WFDD 50 005 36 380 99 WSB 150 14 extraction arm WFAF 50 005 36 372 99 bench mounting bracket WWTB 50 005 36 379 99 Accessories for volume extraction Description Order No. Hose connection 50 for WFE 2S, e.g. for the direct connection of accessories by means of extraction hose 50. Plastic, black. 005 87 358 47 Hose connection 75 for WFE 2S and WFE 4S, e.g. for connection to a stand alone system by means of pipe 75 or extraction hose 75. Plastic, black. 005 87 358 32 Hose connection 50, 90 for WFE 2S, e.g. for the direct connection of accessories by means of extraction hose 50. Plastic, black. 005 87 358 48 Hose connection 75, 90 for WFE 2S and WFE 4S, e.g. for connection to a stand alone system by means of pipe 75 or extraction hose 75. Plastic, black. 005 87 358 33 Extraction hose 50, o 50 mm dia., sold by metre, for the direct connection of accessories . Plastic, grey/black, flexible. 005 87 353 27 Extraction hose 75,o 75 mm dia., sold by metre, for connection to pipe system 75. Plastic, grey/black, flexible. 005 87 353 13 Hose clamp 50 - 70 mm , 2 units, for securing extraction hose 50. 005 87 358 79 Hose clamp 70 - 90 mm , 2 units, for securing extraction hose 75. 005 87 358 31 Extraction arm 50 mm dia flexible extraction arm with articulated joint and airflow control valve and bench clamp. ESD safe. 005 87 358 49 Extraction arm WFAN 50 50 mm dia flexible extraction arm with nozzle, for use with WFFMP 50 system seal. ESD safe. Max. length 800 mm. 005 36 374 99 300 mm 200 mm 100 mm 150 mm 0 mm 100 mm 200 mm 300 mm 200 mm 0 mm 100 mm 100 mm 200 mm 300 mm 300 mm 15 Volume Extraction Accessories Accessories for volume extraction Description Order No. Extraction arm WFAF 50 50 mm dia flexible extraction arm with 100 mm dia funnel, for use with WFFMP 50 system seal. ESD safe. Max. length 840 mm. 005 36 372 99 300 mm 200 mm 100 mm 150 mm 0 mm 300 mm 200 mm 100 mm 0 mm 100 mm 200 mm 300 mm Extraction arm WFAS 50 50 mm dia flexible extraction arm with 210 x 20 mm flat nozzle, for use with WFFMP 50 system seal. ESD safe. Max. length 820 mm. 005 36 373 99 300 mm 200 mm 100 mm 150 mm 0 mm 100 mm 200 mm 300 mm 200 mm 100 mm 0 mm 100 mm 200 mm 300 mm 300 mm Exhaust hood WFCC 50 240 x 100 mm with flexible hose 1m long, recommended for use with hot air soldering operations, for use with WFFMP 50 system seal. ESD safe. 005 36 378 99 100 mm 200 mm 300 mm 300 mm 16 200 mm 100 mm 100 mm 200 mm 300 mm Exhaust hood, 200 x 100 mm recommended for use with hot air soldering operations uses extraction hose 50. 005 87 358 45 Accessories for volume extraction Description Order no. Extraction plate WFDD 50 300 x 210 mm with 1m flexible hose, for adhesive and solvent fume extraction. Uses system seal WFFMP 50. ESD safe. 005 36 380 99 Extraction bench 40 effective working area 600 x 350 mm, for adhesive and solvent fume extraction. Hose connections from side or below. Check hose size info quotes extraction hose 40 and adapter 40-50 neither of which are listed. 005 36 370 99 System seal WFFMP 50 can be mounted directly to work bench or to mounting bracket. It has a spring loaded cover to physically seal the system if an accessory is withdrawn. Connects to hose 50. ESD safe. 005 36 371 99 Bench mounting bracket WFTB 50 for WFFMP 50. Metal, black. 005 36 379 99 17 Accessories for Tip and Volume Extraction Pipe systems for bridging long distances Pipe system 50 Pipe system 75 Tip extraction systems demand a high value and constant level of vacuum across the installation, the volume of air extracted is of lesser importance. To achieve this it is necessary to use a pipe system with relatively small diameter. The Weller pipe system 50 allows extraction installations of up to 200 m when used with the WFE 20D unit in a stand alone system The pipe sections are designed to push together and have internal sealing bushes. In a central system, the FE irons are connected directly to the fume extraction units Volume extraction systems require a large volume of air to be extracted and the level of vacuum is of lesser importance. This means that a relatively large diameter pipe system is required, if the pipe dia was too small the flow resistance would increase and extraction capacity reduced. The pipe system 75 allows installations up to 30 m. with the WFE 4S used in a stand alone system. The pipe sections are designed to push together and have internal sealing bushes. Description Order No. Pipe System 50 Pipe System 75 Pipe, 2 m, with seal at one end, plastic, black. 005 36 323 99 005 87 358 70 Right angle Pipe, 90, 0.5 m, with seal at one end, plastic, black. 005 36 322 99 005 87 358 69 T-piece, 2 x 90, 1 m, with 3 seals, plastic, black. 005 36 344 99 005 87 358 71 Branch, 2 x 45, 1 m, with 2 seals, plastic, black. 005 36 321 99 - Double socket, plastic, black. 005 36 319 99 005 87 353 18 End seal, plastic, transparent. 005 36 324 99 005 87 358 55 Pipe clamps for pipes, e.g. for securing to wall, plastic, grey. 005 36 329 99 005 87 358 64 Adapter pipe system 75 to pipe system 50 with seals. Adapter pipe system 75 to pipe system 50 without seals. 18 005 87 358 63 005 87 358 56 Accessories for all Weller ZeroSmog Systems Exhaust accessories for removing filtered air Description Order No. Pipe 100, 2 m , o 100 mm dia., without seal, for use with WFE 20D and WFE 4S, plastic, black. 005 36 315 99 Pipe 100, 90, 05 m, o 100 mm dia., with seal, for use with WFE 20D and WFE 4S, plastic, black. 005 36 353 99 Exhaust adapter of pipe 100 to WFE 20D. 005 87 359 20 Exhaust adapter of pipe 100 to WFE 4S. 005 87 358 40 Exhaust adapter of pipe 75 for WFE 2S. 005 87 354 13 Remote control Description Order No. Using the Weller remote control, the following functions of the extraction units WFE 20D, WFE 2S and WFE 4S can be controlled remotely: * Switching unit on/off * Speed setting (only WFE 2S / WFE 4S) * Filter status display 005 87 359 09 Interface cable RS 232, 2 m for remote monitoring by PC (type 1:1). Other lengths are available in specialist shops. 005 31 191 99 19 Units for tip extraction WFE WFE P WFE 20D Portable solder fume extraction unit Compressed air-driven for up to 2 FE soldering irons. Portable solder fume extraction unit with built-in turbine for up to 2 FE soldering irons. Mobile solder fume extraction unit with built-in turbine for up to 20 FE soldering irons. Consists of: Extraction unit Compressed air cleaning filter Fine dust filter F7 Compact filter (consists of HEPA filter and wide band gas filter) Consists of: Extraction unit Fine dust filter F7 Compact filter (consists of HEPA filter and wide band gas filter) Consists of: Extraction unit Fine dust filter F5 Compact filter (consists of HEPA filter and wide band gas filter) Order No. 005 36 402 99 Order No. 005 36 386 99 (UK: 005 36 383 99) Order No. 005 36 476 99 (UK: 005 36 473 99) Units for volume extraction (c) 2004, Cooper Industries, Inc. Specifications subject to change without notice. WFE 4S Portable solder fume extraction unit with built-in turbine for up to 4 workplaces. Mobile solder fume extraction unit with built-in turbine for up to 8 workplaces. Consists of: Extraction unit Fine dust filter F5 Compact filter (consists of HEPA filter and wide band gas filter) Hose connection 50 Consists of: Extraction unit Fine dust filter F5 Compact filter (consists of HEPA filter and wide band gas filter) Hose connection 75 Order No. 005 36 266 99 (UK: 005 36 263 99) Order No. 005 36 256 99 (UK: 005 36 253 99) 005 56 170 03 / 08.04 WAL 3.0 WFE 2S G E R M A N Y G R E A T Cooper Tools GmbH Carl-Benz-Str. 2 74354 Besigheim Tel: (07143) 580-0 Fax: (07143) 580-108 Cooper Tools Ltd. Suite 15, Coniston House Town Centre Washington, Tyne & Wear NE38 7RN Tel: (0191) 419 7700 Fax: (0191) 417 9421 B R I T A I N F R A N C E I T A L Y S W I T Z E R L A N D Cooper Tools S.A. 25 Rue Maurice Chevalier BP 46 77832 Ozior-la-Ferriere Cedex Tel: (1) 60.18.55.40 Fax: (1) 64.40.33.05 Cooper Italia S.p.A. Viale Europa 80 20090 Cusago (MI) Tel: (02) 9033101 Fax: (02) 90394231 Erem S.A. Rue de la Roseliere 8 1400 Yverdon les Bains Tel: (024) 426 12 06 Fax: (024) 425 09 77