Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA10F LF 1 A 2 10 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. -O 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional C : with Coating G : Low leakage current J1 : VH(J.S.T.)connector type S : with Chassis SN: with Chassis & cover Y : with Potentiometer Specification is changed at option, refer to Instruction Manual. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LFA10F-3R3-Y 6.6 3.3V 2A LFA10F-5 10 5V 2A LFA10F-12 10.8 12V 0.9A LFA10F-15 10.5 15V 0.7A LFA10F-24 12 24V 0.5A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT ACIN 100V ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *5 LINE REGULATION[mV] LOAD REGULATION[mV] *5 0 to +50C RIPPLE[mVp-p] -10 - 0C *1 Io=0 - 35% 0 to +50C RIPPLE NOISE[mVp-p] OUTPUT -10 - 0C *1 Io=0 - 35% 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION PROTECTION OVERVOLTAGE PROTECTION CIRCUIT AND OPERATING INDICATION OTHERS REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG ISOLATION OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE ENVIRONMENT VIBRATION IMPACT AGENCY APPROVALS SAFETY AND NOISE CONDUCTED NOISE REGULATIONS HARMONIC ATTENUATOR CASE SIZE/WEIGHT OTHERS COOLING METHOD *1 LFA-2 EFFICIENCY[%] LFA10F-3R3-Y LFA10F-5 LFA10F-12 LFA10F-15 LFA10F-24 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *3 0.18typ (Io=100%) 0.26typ (Io=100%) 0.11typ (Io=100%) 0.16typ (Io=100%) 50 / 60 (47 - 440) 68.0typ 74.0typ 76.5typ 77.5typ 79.5typ 68.5typ 76.0typ 79.0typ 80.0typ 83.0typ 15typ (Io=100%) 30typ (Io=100%) 0.15/0.30max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 2.0 2.0 0.9 0.7 0.5 20max 20max 48max 60max 96max 40max 40max 100max 120max 150max 80max 80max 120max 120max 120max 140max 140max 160max 160max 160max 190max 160max 240max 240max 280max 120max 120max 150max 150max 150max 160max 160max 180max 180max 180max 240max 240max 300max 300max 320max 50max 50max 120max 150max 240max 60max 60max 150max 180max 290max 20max 20max 48max 60max 96max 200typ (ACIN 100V, Io=100%) *Start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage. 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 Fixed ("Y"option is available for adjusting output voltage between 10%) 3.30 to 3.40 4.90 to 5.30 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 Works over 105% of rating and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 Not provided Not provided Not provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000 feet) max *3 -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000 feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *6 (Not built-in to active filter) *4 50X22X73.5mm [1.97X0.87X2.89 inches] (WXHXD) / 55g max (with chassis & cover : 150g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *3 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). A circuit reducing standby power is built in this unit. Therefore, the internal switch element is intermittent operated, and the Ripple/Ripple Noise specification in load *2 *3 *4 factor Io=0-35% is different. Please refer to the Instruction Manual 1.7. Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. Derating is required. When two or more units are operating it may not comply with the IEC61000-3-2. *5 *6 * * * * Please contact us for details. Please contact us about dynamic load and input response. Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA10F Block diagram FUSE AC250V 2A AC IN 85 264V INRUSH CURRENT LIMIT NOISE FILTER RECTIFIER AND FILTER LFA FG TRANSFORMER INVERTER CONTROL RECTIFIER AND FILTER DC OUT CURRENT SENSING Photocoupler CONTROL Photocoupler OVER VOLTAGE PROTECTION Chassis and cover type 4.6 [0.18] f3.5 83.5 0.5 63.5 0.5 5 [0.2] 30 CN1 FG [2.5] CN2 5 Input(N) 3 Input(L) 1 1 2 Output(-) Output(+) [2.36] 31.7 Voltage adjust (LFA10F-3R3-Y or optional) 2-f3.5 Mounting Hole [1.18] Input(L) Output(-) Output(+) 60 1 1 2 3.5 Input(N) 15 3 [0.59] FG 30 0.5 [1.18] 5 [0.2] [1.25] [1.97] 40 0.5 [1.57] 50 CN2 CN1 4-M3 Mounting Hole 5 [3.29] [0.14] Standard type FG [0.2] 5 External view 73.5 Name plate [2.89] Point B 93.5 [0.71] [3.68] The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-2 1-1123722-2 Terminal 1123721-1 Chain Loose 1318912-1 Chain 1123721-1 Loose 1318912-1 (Mfr:Tyco Electronics) 2-M3 Mounting Hole 32 [1.26] PCB t=1.6 11 1 Surface mount device [0.43] 1 5 [0.2] 3.5 [0.16] 4max [3.29] 16 83.5 0.5 [0.63] f3.5 [0.14] 18 Point A <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 Input AC(L) AC(N) FG Pin No. Output 1 -V 2 +V Tolerance : 1 [0.04] Weight : 55g max (with chassis & cover : 150g max) PCB material / thickness : CEM3 / 1.6mm Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) : 0.6N-m (6.3kgf-cm) max I/O Connector is Mfr. Tyco Electronics Option:-J1:(J.S.T) connector type. Refer to Instruction Manual 5. LFA-3 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA15F LF 1 A 2 15 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. -O 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional C : with Coating G : Low leakage current J1 : VH(J.S.T.)connector type S : with Chassis SN: with Chassis & cover Y : with Potentiometer Specification is changed at option, refer to Instruction Manual. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LFA15F-3R3-Y 9.9 3.3V 3A LFA15F-5 15 5V 3A LFA15F-12 15.6 12V 1.3A LFA15F-15 15 15V 1A LFA15F-24 16.8 24V 0.7A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT ACIN 100V ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *5 LINE REGULATION[mV] LOAD REGULATION[mV] *5 0 to +50C RIPPLE[mVp-p] -10 - 0C *1 Io=0 - 35% 0 to +50C RIPPLE NOISE[mVp-p] OUTPUT -10 - 0C *1 Io=0 - 35% 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION PROTECTION OVERVOLTAGE PROTECTION CIRCUIT AND OPERATING INDICATION OTHERS REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG ISOLATION OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE ENVIRONMENT VIBRATION IMPACT AGENCY APPROVALS SAFETY AND NOISE CONDUCTED NOISE REGULATIONS HARMONIC ATTENUATOR CASE SIZE/WEIGHT OTHERS COOLING METHOD *1 LFA-4 EFFICIENCY[%] LFA15F-3R3-Y LFA15F-5 LFA15F-12 LFA15F-15 LFA15F-24 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *3 0.24typ (Io=100%) 0.35typ (Io=100%) 0.15typ (Io=100%) 0.20typ (Io=100%) 50 / 60 (47 - 440) 68.0typ 73.0typ 76.0typ 77.0typ 78.0typ 69.0typ 76.0typ 78.5typ 80.0typ 81.5typ 15typ (Io=100%) (At cold start) (Ta=25C) 30typ (Io=100%) (At cold start) (Ta=25C) 0.15/0.30max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 3.0 3.0 1.3 1.0 0.7 20max 20max 48max 60max 96max 40max 40max 100max 120max 150max 80max 80max 120max 120max 120max 140max 140max 160max 160max 160max 190max 160max 240max 240max 280max 120max 120max 150max 150max 150max 160max 160max 180max 180max 180max 240max 240max 300max 300max 320max 50max 50max 120max 150max 240max 60max 60max 150max 180max 290max 20max 20max 48max 60max 96max 200typ (ACIN 100V, Io=100%) *Start-up time is 700ms typ for less than 1minute of applying input again from turning off the input voltage. 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 Fixed ("Y"option is available for adjusting output voltage between 10%) 3.30 to 3.40 4.90 to 5.30 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 Works over 105% of rating and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 Not provided Not provided Not provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000 feet) max *3 -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000 feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *6 (Not built-in to active filter) *4 50X22X87.5mm [1.97X0.87X3.44 inches] (WXHXD) / 80g max (with chassis & cover : 190g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *3 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). A circuit reducing standby power is built in this unit. Therefore, the internal switch element is intermittent operated, and the Ripple/Ripple Noise specification in load *2 *3 *4 factor Io=0-35% is different. Please refer to the Instruction Manual 1.7. Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. Derating is required. When two or more units are operating it may not comply with the IEC61000-3-2. *5 *6 * * * * Please contact us for details. Please contact us about dynamic load and input response. Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA15F Block diagram FUSE AC250V 2.5A AC IN 85 264V INRUSH CURRENT LIMIT NOISE FILTER RECTIFIER AND FILTER LFA FG TRANSFORMER INVERTER CONTROL RECTIFIER AND FILTER DC OUT CURRENT SENSING Photocoupler CONTROL Photocoupler OVER VOLTAGE PROTECTION External view Chassis and cover type 2-f3.5 Mounting Hole 77.5 0.5 Input(N) 3 Input(L) 1 1 2 87.5 [3.44] 107.5 Point B [4.23] 5 PCB t=1.6 2-M3 Mounting Hole 1 Surface mount device The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-2 1-1123722-2 Terminal 1123721-1 Chain Loose 1318912-1 Chain 1123721-1 Loose 1318912-1 (Mfr:Tyco Electronics) 32 [1.26] 1 11 [0.2] 3.5 18 [0.71] [3.84] [0.43] 97.5 0.5 16 f3.5 [0.16] 30 [3.05] Point A 4max Output(-) Output(+) [1.18] CN2 [2.36] 5 60 CN1 FG 3.5 Voltage adjust (LFA15F-3R3-Y or optional) 15 Input(L) 29.7 Input(N) 1 CN2 Output(-) Output(+) [1.17] 3 1 2 [0.63] [0.2] Name plate FG 4-M3 Mounting Hole [0.2] [0.14] 5 5 5 [3.84] [0.59] 50 [1.97] 40 0.5 [1.57] CN1 97.5 0.5 f3.5 [0.17] [0.14] 4.4 30 0.5 [1.18] [0.2] 5 Standard type FG <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 Input AC(L) AC(N) FG Pin No. Output 1 -V 2 +V Tolerance : 1 [0.04] Weight : 80g max (with chassis & cover : 190g max) PCB material / thickness : CEM3 / 1.6mm Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) : 0.6N-m (6.3kgf-cm) max I/O Connector is Mfr. Tyco Electronics Option:-J1:(J.S.T) connector type. Refer to Instruction Manual 5. LFA-5 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA30F LF 1 A 2 30 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. -O 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional C : with Coating G : Low leakage current J1 : VH(J.S.T.)connector type S : with Chassis SN: with Chassis & cover Y : with Potentiometer Specification is changed at option, refer to Instruction Manual. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LFA30F-3R3-Y 19.8 3.3V 6A LFA30F-5 30.0 5V 6A LFA30F-12 30.0 12V 2.5A LFA30F-15 30.0 15V 2A LFA30F-24 31.2 24V 1.3A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 LFA-6 ACIN 100V ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] *5 LOAD REGULATION[mV] *5 0 to +50C*1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C*1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA30F-3R3-Y LFA30F-5 LFA30F-12 LFA30F-15 LFA30F-24 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *3 0.50typ (Io=100%) 0.65typ (Io=100%) 0.30typ (Io=100%) 0.35typ (Io=100%) 50 / 60 (47 - 440) 73typ 76typ 79typ 81typ 82typ 75typ 79typ 81typ 83typ 84typ 15typ (Io=100%) (At cold start) (Ta=25C) 30typ (Io=100%) (At cold start) (Ta=25C) 0.30 / 0.65max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 6.0 6.0 2.5 2.0 1.3 20max 20max 48max 60max 96max 40max 40max 100max 120max 150max 80max 80max 120max 120max 120max 140max 140max 160max 160max 160max 120max 120max 150max 150max 150max 160max 160max 180max 180max 180max 50max 50max 120max 150max 240max 60max 60max 150max 180max 290max 20max 20max 48max 60max 96max 150typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 Fixed ("Y"option is available for adjusting output voltage between 10%) 3.30 to 3.40 4.90 to 5.30 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 Works over 105% of rating and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 Not provided Not provided Not provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max *3 -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *6 (Not built-in to active filter) *4 50X26.5X105mm [1.97X1.04X4.13 inches] (WXHXD) / 130g max (with chassis & cover : 260g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *3 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. Derating is required. *4 *5 *6 * * * * When two or more units are operating it may not comply with the IEC61000-3-2. Please contact us for details. Please contact us about dynamic load and input response. Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA30F Block diagram FUSE AC250V 3.15A AC IN 85 264V INRUSH CURRENT LIMIT NOISE FILTER RECTIFIER AND FILTER LFA FG TRANSFORMER INVERTER CONTROL RECTIFIER AND FILTER DC OUT CURRENT SENSING Photocoupler CONTROL Photocoupler OVER VOLTAGE PROTECTION External view Standard type 95 0.5 [3.74] Input(L) CN2 1 2 3 4 1 Output(-) Output(+) CN1 [2.36] 3 30 5 60 FG Input(N) [1.18] 4-M3 Mounting Hole 3.5 3.5 [0.2] 5 5 [0.2] Output(+) 4 5 [0.2] [0.14] Input(L) CN1 Output(-) 15 1 1 2 3 4 115 0.5 [4.53] [0.59] Input(N) 30 0.5 [1.18] 3 35.8 CN2 FG f3.5 [1.41] 5 [0.18] [0.14] [1.97] 40 0.5 [1.57] 50 4.5 Name plate FG Chassis and cover type 3-f3.5 Mounting Hole Voltage adjust (LFA30F-3R3-Y or optional) [0.16] Mounting Hole 105 [4.13] 125 [4.92] 2-M3 Mounting Hole 1 Surface mount device 4 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-4 1-1123722-4 Terminal 1123721-1 Chain Loose 1318912-1 Chain 1123721-1 Loose 1318912-1 (Mfr:Tyco Electronics) I/O Connector is Mfr. Tyco Electronics Option:-J1:(J.S.T) connector type. Refer to Instruction Manual 5. [1.42] PCB t=1.6 16 1 5 [0.2] 36 [4.53] 11 115 0.5 [0.63] [0.43] f3.5 3.5 [0.14] Point B [0.14] 23 [0.91] 3.5max Point A <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 Input AC(L) AC(N) FG Pin No. Output 1, 2 -V 3, 4 +V Tolerance : 1 [0.04] Weight: 130g max (with chassis & cover : 260g max) PCB material / thickness : CEM3 / 1.6mm Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) : 0.6N-m (6.3kgf-cm) max Keep drawing current per pin below 5A for CN2. LFA-7 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA50F LF 1 A 50 2 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R -O 5 LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional C : with Coating G : Low leakage current J1 : VH(J.S.T.)connector type S : with Chassis SN: with Chassis & cover Y : with Potentiometer Specification is changed at option, refer to Instruction Manual. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LFA50F-3R3-Y LFA50F-5 33 50 3.3V 10A 5V 10A LFA50F-12 51.6 12V 4.3A LFA50F-15 52.5 15V 3.5A LFA50F-24 50.4 24V 2.1A LFA50F-36 50.4 36V 1.4A LFA50F-48 52.8 48V 1.1A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 LFA-8 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR (Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] *4 LOAD REGULATION[mV] *4 0 to +50C*1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C*1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA50F-3R3-Y LFA50F-5 LFA50F-12 LFA50F-15 LFA50F-24 LFA50F-36 LFA50F-48 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *3 0.47typ (Io=100%) 0.67typ (Io=100%) 0.27typ (Io=100%) 0.36typ (Io=100%) 50 / 60 (47 - 63) 73.5typ 77.5typ 80.0typ 80.5typ 81.5typ 82.0typ 81.0typ 74.0typ 79.0typ 81.5typ 81.5typ 83.0typ 83.5typ 82.5typ 0.96typ 0.97typ 0.83typ 0.90typ 15typ (Io=100%) (At cold start) (Ta=25C) 30typ (Io=100%) (At cold start) (Ta=25C) 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 36 48 10.0 10.0 4.3 3.5 2.1 1.4 1.1 20max 20max 48max 60max 96max 144max 192max 40max 40max 100max 120max 150max 240max 240max 80max 80max 120max 120max 120max 150max 150max 140max 140max 160max 160max 160max 200max 200max 120max 120max 150max 150max 150max 250max 250max 160max 160max 180max 180max 180max 300max 300max 50max 50max 120max 150max 240max 360max 480max 60max 60max 150max 180max 290max 450max 600max 20max 20max 48max 60max 96max 144max 192max 350typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 Fixed ("Y"option is available for adjusting output voltage between 10%) 3.30 to 3.40 4.90 to 5.30 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 34.50 to 37.50 46.00 to 50.00 Works over 105% of rating and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 41.40 to 50.40 55.20 to 67.20 Not provided Not provided Not provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max *3 -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *5 50X26.5X132mm [1.97X1.04X5.20 inches] (WXHXD) / 165g max (with chassis & cover : 325g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *3 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 *4 *5 * * * * Derating is required. Please contact us about dynamic load and input response. Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA50F Block diagram FUSE 250V2.5A AC IN 85 NOISE FILTER 264V RECTIFIER INRUSH CURRENT LIMIT LFA FG TRANSFORMER INVERTER CONTROL BOOSTER INDUCTOR CURRENT SENSING RECTIFIER AND FILTER RECTIFIER AND FILTER DC OUT CURRENT SENSING Photocoupler INVERTER CONTROL Photocoupler OVER VOLTAGE PROTECTION CONTROL External view Standard type 4 Point B 122 0.5 [0.16] 3.5 Point A 5 CN2 1 2 3 4 1 CN1 162 PCB t=1.6 1 2-M3 Mounting Hole 1 Surface mount device 4 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-4 1-1123722-4 15 Terminal 1123721-1 Chain Loose 1318912-1 Chain 1123721-1 Loose 1318912-1 (Mfr:Tyco Electronics) I/O Connector is Mfr. Tyco Electronics Option:-J1:(J.S.T) connector type. Refer to Instruction Manual 5. 36 10 3.5 [0.91] 6 [0.24] [1.42] [6.38] 150 0.5 [5.91] f3.5 23 30 132 [5.2] [0.14] [1.18] Mounting Hole [4.8] [0.2] 3.5max Output(-) Output(+) [2.36] 3 [0.14] [0.2] 5 CN2 5 60 Input(N) Input(L) 3.5 20 [0.79] 10 [0.39] FG Output(-) Output(+) Mounting Hole [0.14] 1 2 3 4 CN1 [0.6] 15.2 FG Input(N) Input(L) 4-M3 6 [0.24] [0.59] [0.39] 1 Mounting Hole [0.14] 3 150 0.5 [5.91] 2-f3.5 3-f3.5 4.9 [0.19] 40 0.5 [1.57] 20 0.5 [0.79] [1.97] 40 0.5 [1.57] 5 50 Voltage adjust (LFA50F-3R3-Y or optional) Name plate FG Chassis and cover type <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 Input AC(L) AC(N) FG Pin No. Output 1, 2 -V 3, 4 +V Tolerance : 1 [0.04] Weight : 165g max (with chassis & cover : 325g max) PCB material / thickness : CEM3 / 1.6mm Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) : 0.6N-m (6.3kgf-cm) max Keep drawing current per pin below 5A for CN2. LFA-9 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA75F LF 1 A 75 2 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R -O 5 LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional C : with Coating G : Low leakage current J1 : VH(J.S.T.)connector type S : with Chassis SN: with Chassis & cover Y : with Potentiometer Specification is changed at option, refer to Instruction Manual. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT LFA75F-3R3-Y LFA75F-5 49.5 75 3.3V 15A 5V 15A LFA75F-12 75.6 12V 6.3A LFA75F-15 75 15V 5A LFA75F-24 76.8 24V 3.2A LFA75F-36 75.6 36V 2.1A LFA75F-48 76.8 48V 1.6A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR (Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] LINE REGULATION[mV] *4 LOAD REGULATION[mV] *4 0 to +50C*1 RIPPLE[mVp-p] -10 - 0C *1 0 to +50C*1 RIPPLE NOISE[mVp-p] -10 - 0C *1 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *2 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF INPUT-OUTPUT INPUT-FG OUTPUT-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA75F-3R3-Y LFA75F-5 LFA75F-12 LFA75F-15 LFA75F-24 LFA75F-36 LFA75F-48 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *3 0.70typ (Io=100%) 1.00typ (Io=100%) 0.40typ (Io=100%) 0.50typ (Io=100%) 50 / 60 (47 - 63) 73.5typ 78.0typ 81.5typ 81.5typ 82.5typ 82.5typ 82.5typ 75.0typ 80.0typ 83.0typ 83.0typ 84.5typ 84.5typ 84.5typ 0.96typ 0.97typ 0.83typ 0.90typ 15typ (Io=100%) (At cold start) (Ta=25C) 30typ (Io=100%) (At cold start) (Ta=25C) 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 36 48 15.0 15.0 6.3 5.0 3.2 2.1 1.6 20max 20max 48max 60max 96max 144max 192max 40max 40max 100max 120max 150max 240max 240max 80max 80max 120max 120max 120max 150max 150max 140max 140max 160max 160max 160max 200max 200max 120max 120max 150max 150max 150max 250max 250max 160max 160max 180max 180max 180max 300max 300max 50max 50max 120max 150max 240max 360max 480max 60max 60max 150max 180max 290max 450max 600max 20max 20max 48max 60max 96max 144max 192max 350typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) Fixed ("Y"option is available for adjusting output voltage between 10%) 2.85 to 3.63 3.30 to 3.40 4.90 to 5.30 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 34.50 to 37.50 46.00 to 50.00 Works over 105% of rating and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 41.40 to 50.40 55.20 to 67.20 Not provided Not provided Not provided AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max *3 -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *5 50X33.5X150mm [1.97X1.32X5.91 inches] (WXHXD) / 230g max (with chassis & cover : 440g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *3 This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. LFA-10 *3 *4 *5 * * * * Derating is required. Please contact us about dynamic load and input response. Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA75F Block diagram FUSE 250V3.15A AC IN 85 NOISE FILTER 264V RECTIFIER INRUSH CURRENT LIMIT LFA FG TRANSFORMER INVERTER CONTROL BOOSTER INDUCTOR CURRENT SENSING RECTIFIER AND FILTER RECTIFIER AND FILTER DC OUT CURRENT SENSING Photocoupler INVERTER CONTROL Photocoupler OVER VOLTAGE PROTECTION CONTROL External view Standard type 6 Point A Point B 140 0.5 [5.51] 150 [5.91] 5 [0.2] 4 [0.16] 10 [0.39] 20 [0.79] Output(+) Input(N) Input(L) CN2 5 1 3 3 4 1 CN1 6 Mounting Hole Output(-) Output(+) 60 [2.36] CN1 FG Output(-) 4-M4 5.5 [0.22] 4.5 [0.18] 30 [1.18] 1 3 4 169 0.5 [6.65] 2-f4.5 40 0.5 [1.57] 20 0.5 [0.79] 1 CN2 17.8 Input(N) Input(L) Mounting Hole 3.5 [0.14] FG 3 5 [0.2] 50 [1.97] 40 0.5 [1.57] 5 3-f3.5 13 [0.51] [0.7] Voltage adjust (LFA75F-3R3-Y or optional) Name plate FG Chassis and cover type Mounting Hole 180 [7.09] 169 0.5 [6.65] 5.5 [0.22] 1 2-M4 PCB t=1.6 Mounting Hole 1 Surface mount device 4 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-6 1-1123722-6 4.5 [0.18] 15 15 [0.59] [0.59] 45 [1.77] 3.5max [0.14] 30 [1.18] f4.5 Terminal 1123721-1 Chain Loose 1318912-1 Chain 1123721-1 Loose 1318912-1 (Mfr:Tyco Electronics) I/O Connector is Mfr. Tyco Electronics Option:-J1:(J.S.T) connector type. Refer to Instruction Manual 5. <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 Input AC(L) AC(N) FG Pin No. Output 1 to 3 -V 4 to 6 +V Tolerance : 1 [0.04] Weight : 230g max (with chassis & cover : 440g max) PCB material / thickness : CEM3 / 1.6mm Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) :1.5N-m (16kgf-cm) max Keep drawing current per pin below 5A for CN2. LFA-11 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA100F LF 1 A 100 2 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT *5 *5 -O 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional *1 C : with Coating G : Low leakage current H : with the function to be acceptable to output peak current (only 24V) J1 : VH(J.S.T.)connector type R : with Remote ON/OFF R2 : with Remote ON/OFF S : with Chassis SN: with Chassis & cover Y : with Potentiometer Please refer to Instruction manual 5. LFA100F-3R3-Y LFA100F-5-Y LFA100F-12 LFA100F-15 LFA100F-24 LFA100F-24-H LFA100F-36 LFA100F-48 66 100 102 100.5 103.2 103.2 (129.6) 100.8 100.8 3.3V 20A 5V 20A 12V 8.5A 15V 6.7A 24V 4.3A 24V 4.3 (5.4)A 36V 2.8A 48V 2.1A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR (Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] *5 CURRENT[A] LINE REGULATION[mV] *7 LOAD REGULATION[mV] *7 0 to +50C*2 RIPPLE[mVp-p] -10 - 0C *2 0 to +50C*2 RIPPLE NOISE[mVp-p] -10 - 0C *2 0 to +50C TEMPERATURE REGULATION[mV] -10 to +50C *3 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF *6 INPUT-OUTPUT.RC INPUT-FG *6 OUTPUT.RC-FG *6 OUTPUT-RC OPERATING TEMP.,HUMID.AND ALTITUDE *4 STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA100F-3R3-Y LFA100F-5-Y LFA100F-12 LFA100F-15 LFA100F-24 LFA100F-24-H LFA100F-36 LFA100F-48 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *4 0.9typ (Io=100%) 1.3typ (Io=100%) 0.5typ (Io=100%) 0.7typ (Io=100%) 50 / 60 (47 - 63) 77.0typ 82.0typ 82.0typ 83.0typ 84.0typ 84.0typ 84.0typ 84.5typ 79.0typ 84.0typ 84.5typ 85.5typ 87.0typ 87.0typ 87.0typ 87.0typ 0.98typ 0.99typ 0.92typ 0.95typ 15typ (Io=100%) (At cold start) (Ta=25C) 30typ (Io=100%) (At cold start) (Ta=25C) 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 24 36 48 20 20 8.5 6.7 4.3 4.3 (Peak 5.4) 2.8 2.1 20max 20max 48max 60max 96max 96max 144max 192max 40max 40max 100max 120max 150max 150max 240max 240max 80max 80max 120max 120max 120max 240max 150max 150max 140max 140max 160max 160max 160max 320max 200max 200max 120max 120max 150max 150max 150max 300max 250max 250max 160max 160max 180max 180max 180max 360max 300max 300max 50max 50max 120max 150max 240max 240max 360max 480max 60max 60max 150max 180max 290max 290max 450max 600max 20max 20max 48max 60max 96max 96max 144max 192max 350typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 4.50 to 5.50 Fixed ("Y"option is available for adjusting output voltage) 3.30 to 3.40 5.00 to 5.15 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 23.00 to 25.00 34.50 to 37.50 46.00 to 50.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 27.60 to 33.60 41.40 to 50.40 55.20 to 67.20 Not provided Not provided Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 25mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *8 62X33.5X155mm [2.44X1.32X6.10 inches] (WXHXD) / 280g max (with chassis & cover : 480g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *4 Specification is changed at option, refer to Instruction Manual. This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant LFA-12 *4 *5 *6 *7 at the rated input/output. Derating is required. ( ) means peak current. There is a possibility that an internal device is damaged when the specification is exceeded. Please contact us about the detail. Applicable when Remote ON/OFF (optional) is added. Please contact us about dynamic load and input response. *8 * * * * Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA100F Block diagram FUSE 250V3.15A NOISE FILTER AC IN 85 - 264V RECTIFIER INRUSH CURRENT LIMIT LFA FG Photocoupler OPTION CURRENT SENSING BOOSTER INDUCTOR RC EXTERNAL SOURCE Photocoupler CURRENT SENSING RECTIFIER AND FILTER CONTROL E CONTROL Photocoupler OVER VOLTAGE PROTECTION INVERTER INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL DC OUT External view External size of option is different from standard model. Standard type Input(N) 1 Input(L) 1 2 1 CN4 CN2 Output(-) 4 5 CN1 Output(+) 13 [0.51] 23 [0.91] FG Input(N) 1 2 1 5 3 Input(L) CN1 Output(+) 8 Mounting Hole 3.5max [0.14] 185 [7.28] 1730.5 [6.81] 6 [0.24] 4.5 [0.18] 20 15 [0.79] [0.59] 45 [1.77] f4.5 30 [1.18] 1450.5 [5.71] 155 [6.1] 3.5 [0.14] 5 [0.2] 5 [0.2] 4 [0.16] 16.5 [0.65] CN2 Output(-) 4 5 1 8 Point A Point B Voltage adjust (LFA100F-3R3-Y,LFA100F-5-Y or Optional) 2-M4 Mounting Hole 1 4-M4 Mounting Hole 72 [2.83] FG 3 6 [0.24] 1730.5 [6.81] 2-f4.5 4.5 [0.18] 36 [1.42] 62 [2.44] 520.5 [2.05] 5 Connector for Remote ON/OFF (Optional) 3-f3.5 Mounting Hole 450.5 [1.77] 250.5 [0.98] Name plate FG Chassis and cover type PCB t=1.6 1 Surface mount device 4 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-8 1-1123722-8 Terminal 1123721-1 Chain Loose 1318912-1 Chain 1123721-1 Loose 1318912-1 (Mfr:Tyco Electronics) I/O Connector is Mfr. Tyco Electronics Option:-J1:VH(J.S.T) connector type. Connector type <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN4 Option (Mfr:J.S.T) CN2 Input AC(L) AC(N) Pin No. Output 1 to 4 -V 5 to 8 +V FG Keep drawing current per pin below 5A for CN2. Tolerance : 1 [0.04] Weight : 280g max (with chassis & cover : 480g max) PCB material : CEM3 Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) :1.5N-m (16kgf-cm) max PIN No. 1 2 Contents RC(+) RC(-) Barrier strip type Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 LFA-13 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA150F LF 1 A 150 2 3 F 4 Recommended EMI/EMC Filter NAC-04-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series *The EMI/EMC Filter is recommended to connect with several devices. This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT *5 *5 -O 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional *1 C : with Coating G : Low leakage current H : with the function to be acceptable to output peak current (only 24V) J1 : VH(J.S.T.)connector type R : with Remote ON/OFF R2 : with Remote ON/OFF S : with Chassis SN: with Chassis & cover Y : with Potentiometer Please refer to Instruction manual 5. LFA150F-3R3-Y LFA150F-5-Y LFA150F-12 LFA150F-15 LFA150F-24 LFA150F-24-H LFA150F-36 LFA150F-48 99 150 150 150 151.2 151.2 (189.6) 151.2 153.6 3.3V 30A 5V 30A 12V 12.5A 15V 10A 24V 6.3A 24V 6.3 (7.9)A 36V 4.2A 48V 3.2A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR (Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] *5 CURRENT[A] LINE REGULATION[mV] *7 LOAD REGULATION[mV] *7 0 to +40C*2 RIPPLE[mVp-p] -10 - 0C *2 0 to +40C*2 RIPPLE NOISE[mVp-p] -10 - 0C *2 0 to +40C TEMPERATURE REGULATION[mV] -10 to +40C *3 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF *6 INPUT-OUTPUT.RC INPUT-FG *6 OUTPUT.RC-FG *6 OUTPUT-RC OPERATING TEMP.,HUMID.AND ALTITUDE *4 STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA150F-3R3-Y LFA150F-5-Y LFA150F-12 LFA150F-15 LFA150F-24 LFA150F-24-H LFA150F-36 LFA150F-48 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *4 1.4typ (Io=100%) 2.0typ (Io=100%) 0.7typ (Io=100%) 1.0typ (Io=100%) 50 / 60 (47 - 63) 80.0typ 82.5typ 82.5typ 84.0typ 85.0typ 85.0typ 85.0typ 85.5typ 82.0typ 85.5typ 85.0typ 86.5typ 87.5typ 87.5typ 87.5typ 88.0typ 0.98typ 0.99typ 0.92typ 0.95typ 15typ (Io=100%) (At cold start) (Ta=25C) 30typ (Io=100%) (At cold start) (Ta=25C) 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 24 36 48 30 30 12.5 10 6.3 6.3 (Peak 7.9) 4.2 3.2 20max 20max 48max 60max 96max 96max 144max 192max 40max 40max 100max 120max 150max 150max 240max 240max 80max 80max 120max 120max 120max 240max 150max 150max 140max 140max 160max 160max 160max 320max 200max 200max 120max 120max 150max 150max 150max 300max 250max 250max 160max 160max 180max 180max 180max 360max 300max 300max 50max 50max 120max 150max 240max 240max 360max 480max 60max 60max 150max 180max 290max 290max 450max 600max 20max 20max 48max 60max 96max 96max 144max 192max 350typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 4.50 to 5.50 Fixed ("Y"option is available for adjusting output voltage) 3.30 to 3.40 5.00 to 5.15 11.50 to 12.50 14.40 to 15.60 23.00 to 25.00 23.00 to 25.00 34.50 to 37.50 46.00 to 50.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 27.60 to 33.60 41.40 to 50.40 55.20 to 67.20 Not provided Not provided Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 25mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *8 75X37.0X160mm [2.95X1.46X6.30 inches] (WXHXD) / 390g max (with chassis & cover : 650g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *4 Specification is changeed at option, refer to Instruction Manual. This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant LFA-14 *4 *5 *6 *7 at the rated input/output. Derating is required. ( ) means peak current. There is a possibility that an internal device is damaged when the specification is exceeded. Please contact us about the detail. Applicable when remote control (optional) is added. Please contact us about dynamic load and input response. *8 * * * * Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA150F Block diagram FUSE 250V5A NOISE FILTER AC IN 85 - 264V INRUSH CURRENT LIMIT RECTIFIER LFA FG Photocoupler OPTION CURRENT SENSING BOOSTER INDUCTOR RC RECTIFIER AND FILTER E EXTERNAL SOURCE Photocoupler CURRENT SENSING CONTROL CONTROL Photocoupler INVERTER OVER VOLTAGE PROTECTION INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL DC OUT External view External size of option is different from standard model. Standard type 2-f4.5 FG 3 Input(N) FG Input(N) Input(L) CN3 Output(-) Input(L) CN1 1 7 1 CN2 Output(+) 1 5 CN3 Output(-) 3 1 7 1 CN1 CN2 Output(+) 6 6 Mounting Hole 188 [7.4] 1760.5 [6.93] f4.5 6 [0.24] 4.5 [0.18] 20 15 [0.79] [0.59] 47 [1.85] 5 [0.2] Voltage adjust (LFA150F-3R3-Y,LFA150F-5-Y or Optional) 1500.5 [5.91] 160 [6.3] 4 [0.16] 18 [0.71] 33.5 [1.32] 5 [0.2] 2 1 2 1 3.5 [0.14] 6.5 [0.26] CN4 Connector for Remote ON/OFF (optional) 2-M4 Mounting Hole 3.5max [0.14] 4-M4 Mounting Hole 42 [1.65] 1 5 6 [0.24] 1760.5 [6.93] 85 [3.35] 3-f3.5 Mounting Hole 4.5 [0.18] Point B Point A 15 [0.59] 25 [0.98] Name plate 550.5 [2.17] 350.5 [1.38] 75 [2.95] 650.5 [2.6] FG Chassis and cover type PCB t=1.6 1 1 Surface mount device 4 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-6 1-1123722-6 CN3 1-1123723-7 1-1123722-7 Terminal Chain 1123721-1 1318912-1 Loose 1123721-1 Chain 1318912-1 Loose Chain 1123721-1 1318912-1 Loose (Mfr:Tyco Electronics) I/O Connector is Mfr. Tyco Electronics Option:-J1:VH(J.S.T) connector type. Connector type <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 CN3 CN4 Option (Mfr:J.S.T) Input AC(L) Pin No. Output Pin No. Output AC(N) 1 to 6 +V 1 to 7 -V PIN No. 1 2 Contents RC(+) RC(-) Barrier strip type FG Keep drawing current per pin below 5A for CN2,CN3. Tolerance : 1 [0.04] Weight : 390g max (with chassis & cover : 650g max) PCB material : CEM3 Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) :1.5N-m (16kgf-cm) max Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 LFA-15 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA240F LF 1 A 240 2 3 F 4 Recommended EMI/EMC Filter NAC-06-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] DC OUTPUT *5 *5 LFA240F-24 240 24V 10A LFA240F-24-H 240 (300) 24V 10 (12.5)A LFA240F-36 241.2 36V 6.7A -O 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional *1 C : with Coating G : Low leakage current H : with the function to be acceptable to output peak current (only 24V) J1 : VH(J.S.T.)connector type R : with Remote ON/OFF R2 : with Remote ON/OFF S : with Chassis SN: with Chassis & cover T : Vertical terminal block Y : with Potentiometer Please refer to Instruction manual 5. LFA240F-48 240 48V 5A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR (Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] *5 CURRENT[A] LINE REGULATION[mV] *7 LOAD REGULATION[mV] *7 0 to +40C*2 RIPPLE[mVp-p] -10 - 0C *2 0 to +40C*2 RIPPLE NOISE[mVp-p] -10 - 0C *2 0 to +40C TEMPERATURE REGULATION[mV] -10 to +40C *3 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF *6 INPUT-OUTPUT.RC INPUT-FG *6 OUTPUT.RC-FG *6 OUTPUT-RC OPERATING TEMP.,HUMID.AND ALTITUDE *4 STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA240F-24 LFA240F-24-H LFA240F-36 LFA240F-48 AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *4 3.3typ (Io=100%) 1.7typ (Io=100%) 50 / 60 (47 - 63) 84.5typ 84.5typ 84.5typ 84.5typ 87.5typ 87.5typ 87.5typ 87.5typ 0.99typ 0.95typ 15 / 30typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 3 sec. to re-start) 30 / 30typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 3 sec. to re-start) 0.40 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 24 24 36 48 10 10 (Peak12.5) 6.7 5 96max 96max 144max 192max 150max 150max 240max 240max 120max 240max 150max 150max 160max 320max 200max 200max 150max 300max 250max 250max 180max 360max 300max 300max 240max 240max 360max 480max 290max 290max 450max 600max 96max 96max 144max 192max 350typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) Fixed ("Y"option is available for adjusting output voltage) 23.00 to 25.00 23.00 to 25.00 34.50 to 37.50 46.00 to 50.00 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 27.60 to 33.60 27.60 to 33.60 41.40 to 50.40 55.20 to 67.20 Not provided Not provided Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 25mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *8 84X46.5X180mm [3.31X1.83X7.09 inches] (WXHXD) / 550g max (with chassis & cover : 880g max) Convection (Refer to Instruction Manual 3.1 and 3.2) *4 Specification is changeed at option, refer to Instruction Manual. This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant LFA-16 *4 *5 *6 *7 at the rated input/output. Derating is required. ( ) means peak current. There is a possibility that an internal device is damaged when the specification is exceeded. Please contact us about the detail. Applicable when remote control (optional) is added. Please contact us about dynamic load and input response. *8 * * * * Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA240F Block diagram FUSE 250V10A NOISE FILTER AC IN 85 - 264V RECTIFIER INRUSH CURRENT LIMIT LFA FG Photocoupler OPTION CURRENT SENSING RC CURRENT SENSING RECTIFIER AND FILTER E EXTERNAL SOURCE Photocoupler BOOSTER INDUCTOR CONTROL CONTROL Photocoupler INVERTER OVER VOLTAGE PROTECTION INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL DC OUT External view External size of option is different from standard model. Standard type 7 1 Mounting Hole [8.35] [7.87] [1.69] 1 30 2-M4 Mounting Hole 59 [0.24] 4.5 [7.09] [0.14] 6 2000.5 [2.32] f4.5 180 43 49 212 [6.69] [0.2] 15 4 [0.16] [0.59] Point A Point B [1.18] 1700.5 CN2 Output(+) 6 3.5 890.5 [3.5] 4.5 CN1 CN2 Output(+) [0.14] 5 [0.2] 5 CN3 Output(-) 1 [3.86] 3 98 1 5 [0.18] [1.77] 7 1 450.5 CN1 650.5 CN3 Output(-) FG Input(N) Input(L) [1.93] [1.04] 16.5 1 2 1 [2.56] 740.5 [2.91] [3.31] 1 CN4 4-M4 Mounting Hole [0.24] 6 3.5max 84 3 FG Input(N) Input(L) 6 [7.87] [0.18] 1 2 5 2000.5 2-f4.5 4-f3.5 Mounting Hole [0.65] 16.5 [0.65] 26.5 Name plate 21 Connector for Remote ON/OFF (Optional) Voltage adjust(Optional) [0.83] FG Chassis and cover type PCB t=1.6 1 Surface mount device 5 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B are thermometry points. Please refer to Instruction Manual 3. I/O Connector Mating connector CN1 1-1123724-3 1-1123722-5 CN2 1-1123723-6 1-1123722-6 CN3 1-1123723-7 1-1123722-7 Terminal Chain 1123721-1 1318912-1 Loose 1123721-1 Chain 1318912-1 Loose Chain 1123721-1 1318912-1 Loose (Mfr:Tyco Electronics) I/O Connector is Mfr. Tyco Electronics Option:-J1:VH(J.S.T) connector type. Connector type <PIN CONNECTION> CN1 Pin No. 1 2 3 4 5 CN2 CN3 CN4 Option (Mfr:J.S.T) Input AC(L) Pin No. Output Pin No. Output AC(N) 1 to 6 +V 1 to 7 -V PIN No. 1 2 Contents RC(+) RC(-) Barrier strip type FG Keep drawing current per pin below 5A for CN2,CN3. Tolerance : 1 [0.04] Weight : 550g max (with chassis & cover : 880g max) PCB material : CEM3 Optional chassis and cover material : Electric galvanizing steel board. Dimensions in mm, [ ]=inches Mounting torque (Mounting hole of chassis) :1.5N-m (16kgf-cm) max Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 LFA-17 Ordering information AC-DC Power Supplies Open Frame/ Enclosed Type LFA300F LF 1 A 300 2 3 F Recommended EMI/EMC Filter NAC-06-472 R LFA High voltage pulse noise type : NAP series Low leakage current type : NAM series This power supply is manufactured by SMD technology. The stress to P.C.B like twisting or bending causes the defect of the unit, so handle the unit with care. MODEL MAX OUTPUT WATTAGE[W] Convection *5 DC OUTPUT Forced air *5 LFA300F-3R3-TY 198 3.3V 40A 3.3V 60A LFA300F-5-TY 300 5V 40A 5V 60A LFA300F-12-TY 324 12V 17A 12V 27A LFA300F-15-TY 330 15V 14A 15V 22A LFA300F-24-TY 336 24V 12.5A 24V 14A -O 4 LFA300F-24-HTY 336 (456) 24V 12.5 (19)A 24V 14 (19)A 5 -O 6 1 Series name 2 Single output 3 Output wattage 4 Universal input 5 Output voltage 6 Optional *1 C : with Coating G : Low leakage current H : with the function to be acceptable to output peak current (Only 24V, 30V, 36V and 48V) J : EP (Tyco Electronics) connector type (Except 3.3V and 5V) J1 : VH (J.S.T.) connector type (Except 3.3V and 5V) R : with Remote ON/OFF R2 : with Remote ON/OFF S : with Chassis SNF : with Chassis & cover & fan (Only 5V, 12V and 24V) T1 : Holizontal terminal block Please refer to Instruction manual 5. LFA300F-30-TY 330 30V 10A 30V 11A LFA300F-36-TY 338.4 36V 8.4A 36V 9.4A LFA300F-48-TY 336 48V 6.3A 48V 7A SPECIFICATIONS MODEL VOLTAGE[V] CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS *1 *2 *3 ACIN 100V ACIN 200V ACIN 100V POWER FACTOR (Io=100%) ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] Convection *5 CURRENT[A] Forced air LINE REGULATION[mV] *7 LOAD REGULATION[mV] *7 0 to +40C*2 RIPPLE[mVp-p] -10 - 0C *2 0 to +40C*2 RIPPLE NOISE[mVp-p] -10 - 0C *2 0 to +40C TEMPERATURE REGULATION[mV] -10 to +40C *3 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION OPERATING INDICATION REMOTE SENSING REMOTE ON/OFF *6 INPUT-OUTPUT.RC INPUT-FG *6 OUTPUT.RC-FG *6 OUTPUT-RC OPERATING TEMP.,HUMID.AND ALTITUDE *4 STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LFA300F-3R3-TY LFA300F-5-TY LFA300F-12-TY LFA300F-15-TY LFA300F-24-TY LFA300F-24-HTY LFA300F-30-TY LFA300F-36-TY LFA300F-48-TY AC85 - 264 1f (Refer to Instruction Manual 1.1 and 3.2) *4 2.7typ (Io=100%) 4.1typ (Io=100%) 1.4typ (Io=100%) 2.0typ (Io=100%) 50 / 60 (47 - 63) 75.0typ 79.0typ 80.0typ 81.5typ 85.0typ 85.0typ 85.5typ 85.5typ 85.5typ 77.0typ 82.5typ 83.0typ 84.5typ 88.0typ 88.0typ 88.0typ 88.0typ 88.0typ 0.98typ 0.99typ 0.92typ 0.95typ 15 / 30typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 3 sec. to re-start) 30 / 30typ (Io=100%) (Primary inrush current /Secondary inrush current) (More then 3 sec. to re-start) 0.45 / 0.75max (ACIN 100V / 240V 60Hz, Io=100%, According to IEC60950-1 and DEN-AN) 3.3 5 12 15 24 24 30 36 48 40 40 17 14 12.5 12.5 (Peak19) 10 8.4 6.3 60 60 27 22 14 14 (Peak19) 11 9.4 7 20max 20max 48max 60max 96max 96max 144max 144max 192max 40max 40max 100max 120max 150max 150max 240max 240max 240max 80max 80max 120max 120max 120max 240max 150max 150max 150max 140max 140max 160max 160max 160max 320max 200max 200max 200max 120max 120max 150max 150max 150max 300max 250max 250max 250max 160max 160max 180max 180max 180max 360max 300max 300max 300max 50max 50max 120max 150max 240max 240max 360max 360max 480max 60max 60max 150max 180max 290max 290max 450max 450max 600max 20max 20max 48max 60max 96max 96max 144max 144max 192max 350typ (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 2.85 to 3.63 4.50 to 5.50 10.80 to 13.20 13.50 to 16.50 21.60 to 27.50 21.60 to 27.50 27.00 to 33.00 32.40 to 39.60 39.60 to 52.80 3.30 to 3.40 5.00 to 5.15 12.00 to 12.48 15.00 to 15.60 24.00 to 24.96 24.00 to 24.96 30.00 to 31.20 36.00 to 37.44 48.00 to 49.92 Works over 105% of rating (works over 101% of peak current at option -H) and recovers automatically 4.00 to 5.25 5.75 to 7.00 13.80 to 16.80 17.25 to 21.00 27.60 to 33.60 27.60 to 33.60 34.50 to 42.00 41.40 to 50.40 55.20 to 67.20 Not provided Not provided Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 25mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 25mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to Instruction Manual 3.2), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL (CSA60950-1), EN60950-1, EN60065, EN50178 Complies with DEN-AN Complies with FCC-B, VCCI-B, CISPR-B, EN55011-B, EN55022-B Complies with IEC61000-3-2 (Class A) *8 95X52.5X222mm [3.74X2.07X8.74 inches] (WXHXD) (without terminal block) / 810g max (with chassis & cover : 1,270g max) Convection / Forced air (Refer to Instruction Manual 3.1 and 3.2) *4 Specification is changeed at option, refer to Instruction Manual. This is the value that measured on measuring board with capacitor of 22mF at 150mm from output terminal. Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM103). Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant LFA-18 *4 *5 *6 *7 at the rated input/output. Derating is required. ( ) means peak current. There is a possibility that an internal device is damaged when the specification is exceeded. Please contact us about the detail. Applicable when remote control (optional) is added. Please contact us about dynamic load and input response. *8 * * * * Please contact us about another class. To meet the specifications. Do not operate over-loaded condition. Parallel operation is not possible. Derating is required when operated with chassis and cover. Sound noise may be generated by power supply in case of pulse load. LFA300F Block diagram FUSE 250V10A NOISE FILTER AC IN 85 - 264V INRUSH CURRENT LIMIT RECTIFIER LFA FG Photocoupler OPTION CURRENT SENSING RC EXTERNAL SOURCE Photocoupler BOOSTER INDUCTOR CURRENT SENSING RECTIFIER AND FILTER CONTROL E CONTROL Photocoupler INVERTER OVER VOLTAGE PROTECTION INVERTER RECTIFIER AND FILTER TRANSFORMER CONTROL DC OUT External view External size of option is different from standard model. Standard type Name plate Point C for Point B Connector Remote ON/OFF (Optional) Point D M4 1 2 CN4 TB2 [2.07] Output(+) [0.2] Point A 2120.5 Voltage adjust 4 [0.16] 46.5 3.5 1090.5 [4.29] [0.14] 5.5 5 [0.22] 5 M4 [0.2] 8.6 Output(-) Input(L) [0.34] [0.39] 10 52.5 850.5 Input(N) TB1 [3.35] 95 [3.74] FG 18.5 10 FG [0.73] [0.39] 8.6 [0.34] 4-f3.5 Mounting Hole Mounting Hole [1.83] [8.35] 222 Connector type [8.74] PIN No. 1 2 [1.93] 49 CN4 Option (Mfr:J.S.T) Contents RC(+) RC(-) [0.14] 3.5max Barrier strip type 1 PCB t=1.6 1 Surface mount device 5 Mounting holes are existing. The back side of P.C.B. of the power supply is assembled some SMDs. Be attention not to bump against the attached area by vibration. Use the spacer of 8mm length or more regarding insulation. And do not use press-fitting bush. Point A, Point B, Point C, Point D are thermometry points. Please refer to Instruction Manual 3. Keep drawing current per pin below 20A for TB2. Model B2B-XH-A Mating Connector (Terminal) XHP-2 BXH-001T-P0.6 or SXH-001T-P0.6 Tolerance : 1 [0.04] Weight : 810g max (with chassis & cover : 1,270g max) PCB material : CEM3 Dimensions in mm, [ ]=inches Screw tightening torque : M4 1.6N-m (16.9kgf-cm) max LFA-19