THT CURRENT SENSE TRANSFORMERS UL/C-UL recognized components 3000Vrms gate to drive winding test Useful operating frequency from 50kHz to 500kHz Most popular winding configurations Electrical Specifications @ 25C -- Operating Temperature -40C to 130C 6 Part Number Turns Ratio Primary Inductance (1-10) (mH MIN) DCR Pri (1-10) ( MAX) DCR Sec1 (3-7) (m 15%) DCR Sec2 (4-8) (m 15%) Hi-Pot (Pri-Sec) (Vrms) P0581 P0582 P0583 200:1:1 100:1:1 50:1:1 76 19 5 2.8 1.4 0.7 1.7 1.7 1.7 1.7 1.7 1.7 3000 3000 3000 Additional Specifications Part Number RT P0581 P0582 P0583 200 100 15 Reference Data Ipk Droop (Amps) (%) 34 1.00 35 1.98 36 1.19 NOTES: 1. These current sense transformers have two one turn primaries that can be used in parallel. The listed current ratings are for parallel connection. 2. The reference values are for an application using the termination resistor (Rt) and operating with unipolar waveform at 100kHz, 40% duty cycle. The estimated temperature rise is 55C. 3. The peak flux density should remain below 2100 Gauss to ensure that the core does not saturate. Use the following formula to calculate the peak flux density: Bpk = Kb * Ipk * Rt * don/(Ff * Freq. in kHz) where: Rt is the terminating resistor in the application and Ff is 1 for unipolar waveform and 2 for bipolar waveform Calculation Data Max Flux Density 2000 2000 2000 17.12 68.49 273.97 4. To calculate the droop: Droop Exponent (D) = Rt * don/(Lpri in mH * Freq. in kHz) %Droop = (1-e-D) * 100 5. The temperature rise of the component is calculated based on the total core loss and copper loss: A. To calculate total copper loss (W): P(cu) = Ipk2 * Req * Ff * don where: Ff is 1 for unipolar waveform and 2 for bipolar waveform B. To calculate total core loss (W): P(core) = 0.000073 * (Freq. in kHz)1.67 * (Bop in kG)2.532 where: Bop in kG = Kb * Ipk * Rt * don/(2000 * Freq. in kHz) C. To calculate temperature rise: Temperature Rise (C) = 60.18 * (Core Loss(W) + Copper Loss (W)).833 6. To order RoHS compliant part, add the suffix "NL" to the part number (i.e. P0581 becomes P0581NL). Mechanical .810 MAX 20,57 Schematic .580 MAX 14,73 Pri Sec 3 .750 MAX 19,05 1T 1 P058X .130 3,30 Req (m) .9 .8 .75 Kb 50T, 100T, or 200T Date Code Country of Origin 10 3 1 4 10 .350 8,89 7 10 8 For More Information: .700 17,78 1 7 7 Weight . . . . . . . . . . . . . . . .5 grams Tray . . . . . . . . . . . . . . . . . . .20/tray (6X) .040 .200 5,08 1T 4 8 4 SUGGESTED PCB HOLE PATTERN Dimensions: Inches mm Unless otherwise specified, all tolerances are .010 0,25 Pulse Worldwide Headquarters Pulse Northern Europe Pulse Southern Europe Pulse Pulse North China China Headquarters Room 1503 12220 World Trade Drive San Diego, CA 92128 U.S.A. www.pulseeng.com TEL: 858 674 8100 FAX: 858 674 8262 3 Huxley Road Surrey Research Park Guildford, Surrey GU2 5RE United Kingdom TEL: 44 1483 401700 FAX: 44 1483 401701 Zone Industrielle F-39270 Orgelet France TEL: 33 3 84 35 04 04 FAX: 33 3 84 25 46 41 No. 1 Industrial District Changan, Dongguan China TEL: 86 769 85538070 FAX: 86 769 85538870 XinYin Building No. 888 YiShan Road Shanghai 200233 China TEL: 86 21 54643211/2 FAX: 86 21 54643210 Pulse South Asia Pulse North Asia 150 Kampong Ampat #07-01/02 KA Centre Singapore 368324 No. 26 Kao Ching Road Yang Mei Chen Taoyuan Hsien Taiwan, R. O. C. TEL: 886 3 4641811 FAX: 886 3 4641911 TEL: 65 6287 8998 FAX: 65 6280 0080 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. (c) Copyright, 2006. Pulse Engineering, Inc. All rights reserved. www.pulseeng.com P516.B (3/06)