ACDC
Specification
225 Watts
•Low 1” Profile with 2.5” x 5” Footprint
•150/225 W Convection/ Forcedcooled
•High Efficiency up to 95%
•Medical & ITE Approvals
•Builtin Fan Supply
•<0.5 W No Load Input Power
•3 Year Warranty
ECP Series
Input
Input Voltage • 85-264 VAC, Derate from 100% at 90 VAC
to 90% at 85 VAC
Input Frequency • 47-63 Hz
Input Current • 2.2 A typical at 115 VAC, 1.1 A typical at
230 VAC
Inrush Current • 120 A max at 230 VAC, cold start at 25 °C
Power Factor • >0.95 at full load
Earth Leakage Current • <230 µA at 264 VAC, 60 Hz
No Load Input Power • <0.5 W
Input Protection • Internal T3.15A/250VAC fitted in line and
neutral
Output
Output Voltage • See tables
Output Voltage Trim • ±5%
Initial Set Accuracy • ±1% at 50 % load
Minimum Load • No minimum load requirement
Start Up Delay • 2 s max
Start Up Rise Time • 55 ms typical
Hold Up Time • 10 ms minimum at full load and 115 VAC
20 ms typical at 150 W, 13 ms typical at
225 W
Line Regulation • ±0.5% max
Load Regulation • ±0.5% max
Transient Response • 4% maximum deviation, recovering to less
than 1% within 500 µs for 25% step load
Ripple & Noise • 1% max pk-pk, 20 MHz bandwidth,
(see note 2)
Overvoltage Protection • 110% - 140% of nominal voltage on main
output. Recycle mains to reset.
Overload Protection • 110-170%
Short Circuit Protection • Trip and restart (hiccup)
Thermal Protection • Measured internally. Auto resetting.
Temperature • 0.02%/°C
Coefficient
Fan Supply • 12 V at 500 mA
xppower.com
General
Efficiency • See table
Isolation • 4000 VAC Input to Output
1500 VAC Input to Ground
1500 VAC Output to Ground
Protection Level • Primary to Secondary: 2 MOPP
Primary to Earth: 1 MOPP
Secondary to Earth: 1 MOPP
Power Density • 12/18 W/in3convection/forced-cooled,
Switching Frequency • PFC: 70-130 KHz, PWM: 50-80 KHz
MTBF • >300 kHrs to MIL-HDBK-217F at 25 °C, GB
Environmental
Operating Temperature • -20 °C to +70 °C derate from 100% load
at 50 °C to 50% load at 70 °C
Cooling • Convection cooled: 150 W
Forced cooled: 225 W with 10 CFM
Operating Humidity • 5% to 90% RH, non condensing
Operating Altitude • 5000 m
Storage Temperature • -40 °C to +85 °C
Shock • IEC68-2-27, 30 g, 11 ms half sine, 3 times
in each of 6 axes
Vibration • IEC68-2-6, 10-500 Hz, 2 g 10 mins /
sweep. 60 mins for each of 3 axes
EMC & Safety
Emissions • EN55022/11, Level B conducted &
Level A radiated, Level B radiated with
external core, see note 5.
Harmonic Currents • EN61000-3-2 Class A
EN61000-3-2 Class C for load >145 W
Voltage Flicker • EN61000-3-3
ESD Immunity • EN61000-4-2, ±8 kV air, ±4 kV contact,
Perf Criteria A
Radiated Immunity • EN61000-4-3, 3 V/m, Perf Criteria A
EFT/Burst • EN61000-4-4, level 3, Perf Criteria A
Surge • EN61000-4-5, installation class 3,
Perf Criteria A
Conducted Immunity • EN61000-4-6, 3 V, Perf Criteria A
Dips & Interruptions • EN55024, 100% 10 ms,
30%, 500 ms, 100%, 5000 ms
Perf Criteria A, A, B for high line,
A, B, B for low line at full load,
EN60601-1-2, 30% 500 ms, 60% 100 ms,
100% 10 ms, 100% 5000 ms,
Perf Criteria A, A, A, B for high line,
A, B, A, B for low line at full load
Safety Approvals • UL60950-1, IEC60950-1, EN60950-1,
ANSI/AAMI ES 60601-1, IEC60601-1,
EN60601-1
Mechanical Details
16-Dec-13
ACDC
ECP225
Models and Ratings
Output Voltage Output Current Ripple and Noise
pk-pk(2) Fan Output Efficiency(3) Model Number(4)
Convection-cooled Forced-cooled(1)
12.0 V 12.50 A 18.75 A 120 mV 12 V/0.5 A 93% ECP225PS12
15.0 V 10.00 A 15.00 A 150 mV 12 V/0.5 A 93% ECP225PS15
24.0 V 6.25 A 9.38 A 240 mV 12 V/0.5 A 94% ECP225PS24
28.0 V 5.36 A 8.04 A 280 mV 12 V/0.5 A 94% ECP225PS28
48.0 V 3.10 A 4.69 A 480 mV 12 V/0.5 A 94% ECP225PS48
1. Requires 10 CFM.
2. Measured with 20 MHz bandwidth and 10 µF electrolytic capacitor in parallel
with 0.1 µF ceramic capacitor
3. Minimum average efficiencies measured at 25%, 50%, 75% & 100% of
225 W load and 230 VAC input.
4. 3” x 5” Footprint available for OEM quantities, add suffix ‘-3X5’to part eg.
ECP225PS24-3X5.
5. To meet Level B radiated, a torroid is required on output load leads. Use King
Core type K5B RC 25*12*15 for all models except 28V which requires type
K5B T 16.5*13*8.2.
Notes
Notes
CN1 - Input Connector
Pin 1 Neutral
Pin 2 Not Fitted
Pin 3 Line
CN2 - Output Connector
Pin 1 -Vout
Pin 2 -Vout
Pin 3 -Vout
Pin 4 -Vout
Pin 5 +Vout
Pin 6 +Vout
Pin 7 +Vout
Pin 8 +Vout
Mounting holes marked with
must be connected to safety earth
Mates with JST housing
VHR-8N and JST Series
SVH-21T-P1.1 crimp terminals
-10
-20 010 20 30 40 50 60 70
20
40
60
80
100
Ambient Temperature (ºC)
Output Power (%)
0
80
1. All dimensions shown in inches (mm).
Tolerance: ±0.02 (0.5)
2. Weight: 0.51 lbs (230 g) approx.
3. Non earthed mounting hole on secondary side requires insulated mounting to
maintain 1 MOPP secondary to ground.
Mates with JST housing
VHR-3N and JST Series
SVH-21T-P1.1 crimp terminals
CN3 - Fan Connector
Pin 1 Fan -
Pin 2 Fan +
Mates with Molex housing
22-01-1022 and 2759 crimp terminals
Derating Curve
5.00 (127.0)
4.75 (120.6)
2.50
(63.5)
2.25
(57.1)
0.134 (Ø3.4 ±0.3)
8
1
VR
CN2
CN3
1
2
0.25 (6.35) Faston ground tab
CN1
Mounting Screw
Holes 4 Places
1
3
0.06
(1.60) 0.83
(21.0)
0.11
(2.80)
1.00
(25.4)