MP2060 Kool-Pak(R) Clip Mount Power Film Resistor TO-220 Style Power Resistor Designed for Clip Mounting - Non-Inductive * * * * * * * * Up to 60 Watts continuous power at +25C case temperature, 0.020 and above. Up to 60 Amps continuous current at +25C case temperature, 0.015 and below. TO-220 Style package utilizes proven power semiconductor thermal solutions. Equivalent to UL94 V-0 flammability rating. Excellent pulse/surge performance. Non-inductive design for high speed switching, snubbers and rf applications. Operation up to +150C case temperature. Electrically isolated case. Model Package Power Rating Resistance MP2060 0.010 TO-220 Style Thermal Resistance Max. Current Max. RJC Rating (Amps) Voltage * 36 Watts * 54 Watts * 60 Watts * 18 Watts 0.005 0.015 0.020 to 1.00K RATED POWER % Derating Curve 100 80 60 40 20 0 25 100 150 CASE TEMPERATURE, C Current Limited Current Limited Current Limited 60 Arms 60 Arms 60 Arms I= 250 Vrms P/ R Film (J) to Case (C) 6.94C/Watt 3.47C/Watt 2.31C/Watt 2.08C/Watt * Derating Using Case Temperature (TC): All power and associated overload ratings are derated based upon case temperature using the derating curve. The case temperature is measured at the center of the ceramic mounting surface, with the part properly mounted and under electrical load. Without a heat sink, when in free air at +25C, the MP2060 is rated for 2.5 watts. The thermal design should satisfy the following equation: Case Temperature (Tc) + [Thermal Resistance (RJC) x power applied (Watts)] 150C, considering the full operating temperature range of the application. Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material, such as thermal grease. The entire exposed ceramic portion must be in contact with the heat sink. When using a spring clip, it is recommended that a mounting force of 8 to 30 pounds (35 to 130 N) be applied to the center of the package. The clip should be round or smooth in the contact area to avoid concentrating the load on a small point of the plastic body of the package. Another mounting option is to use a pressure bar method which can achieve a greater mounting force with a greater contact area. For additional applications information regarding mounting and pulse handling see the Caddock Applications Notes at caddock.com or contact Applications Engineering. 0.175 0.010 (4.45 0.26) 0.410 0.010 (10.41 0.26) 0.150 0.030 (3.81 0.76) 0.640 0.010 (16.26 0.26) MP2060 50.0 1% 0.100 0.020 (2.54 0.51) 0.500 0.050 (12.70 1.27) 0.050 0.007 (1.27 0.18) 0.200 0.010 (5.08 0.26) 0.035 0.007 (0.89 0.18) 0.105 0.010 (2.67 0.26) DIMENSIONS IN INCHES AND (MILLIMETERS) Ordering Information: Model Number: Standard Resistance Values: Tolerance: 1% Standard (except as noted) 0.005 5% 0.010 2% 0.015 2% 0.020 0.025 0.030 0.033 0.040 0.050 0.075 0.10 0.15 0.20 0.25 0.30 0.33 0.40 0.50 0.75 1.00 1.50 2.00 2.50 3.00 3.30 4.00 5.00 7.50 8.00 10.0 12.0 15.0 20.0 25.0 27.0 30.0 33.0 40.0 47.0 50.0 56.0 75.0 100 120 150 200 250 300 330 400 470 500 560 750 1.00 K For custom values and tolerances contact Applications Engineering MP2060 - 0.050 - 1% Resistor Value: Tolerance Packaging Information: MP2060 resistors are packaged in plastic shipping tubes, 50 pieces per tube. These resistors are available in a 50 piece minimum quantity and in full tube quantity increments (i.e. 50, 100, 150, etc.). Applications Engineering 17271 North Umpqua Hwy. Roseburg, Oregon 97470-9422 Phone: (541) 496-0700 Fax: (541) 496-0408 (c) 2004 Caddock Electronics, Inc. New Clip M Value ount 0.005s to CADDOCK These products are covered by one or more patents, also patents pending. Specifications: Temperature Coefficient: TC referenced to +25C, R taken at +150C 0.50 ohm and above, -20 to +80 ppm/C 0.050 ohm to 0.49 ohm, 0 to +100 ppm/C 0.015 ohm to 0.049 ohm, 0 to +200 ppm/C 0.005 ohm to 0.014 ohm, 0 to +300 ppm/C Operating Temperature: -55C to +150C Inductance: 10 nH typical in series when measured at the shoulder of the lead. Capacitance: <1 pf typical without heat sink. DWV: 1500 VrmsAC isolation to the mounting surface or a clip in contact with the top surface. Insulation Resistance: 10,000 Megohms, min. The resistor element is electrically isolated from the mounting surface. Momentary Overload: 1.5 times rated power for 5 seconds, R (0.5 percent + 0.0005 ohm) max. Load Stability: 2000 hours at rated power R less than (1 percent +0.0005 ohm). Moisture Resistance: Mil-Std-202, Method 106, R (0.5 percent + 0.0005 ohm) max. Thermal Shock: Mil-Std-202, Method 107, Cond. F, R (0.5 percent + 0.0005 ohm) max. Shock: 100G, Mil-Std-202, Method 213, Cond. I, R (0.4 percent + 0.0005 ohm) max. Vibration, High Frequency: Mil-Std 202, Method 204, Condition D, R (0.4 percent + 0.0005 ohm) max. Terminal Strength: Mil-Std-202, Method 211, Cond. A (Pull Test) 5 lbs., R (0.2 percent + 0.0005 ohm) max. Terminal Material: Solderable Measurement Note: Resistance measurements shall be made at 0.2 inch (5.08 mm) from the resistor body. e-mail: caddock@caddock.com * web: www.caddock.com For Caddock Distributors listed by country see caddock.com/contact/dist.html Sales and Corporate Office 1717 Chicago Avenue Riverside, California 92507-2364 Phone: (951) 788-1700 Fax: (951) 369-1151 28_IL128.1004