Finisar Corpor ation August 2015 Rev. B1 Page 1
Product Specification
OC-3 IR-1/STM S-1.1 RoHS C ompliant Pluggable SFP Transceive r
FTLF1323P1xTR
PRODUCT FEATURES
Up to 155 Mb/s bi-directional
data links
Hot-pluggable SFP footprint
Built-in digital diagnostic functions
Uncooled Fabry-Perot 1310nm
laser transmitter
Duplex LC connector
RoHS compliant and lead-free
Metal enclosure, for lower EMI
Single 3.3V power supply
Low power dissipation <700mW
typical
Industrial operating temperature
range: -40°C to 85°C
APPLICATIONS
SONET OC-3 IR-1 / SDH STM S-1.1
SONET OC-3 SR / SDH STM I-1
Suitable for Fast Ethernet
Finisar’s FTLF1323P1xTR Small Form Factor Pluggable (SFP) transceivers are
compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.
They comply with SONET and SDH standards2 at OC-3 IR-1/STM S-1.1 and OC-3
SR/STM I-1, and are suitable for Fast Ethernet applications. Digital diagnostics
functions are available via the 2-wire serial bus specified in the SFP MSA. The optical
transceiver is compliant per the RoHS Directive 2011/65/EU3. See Finisar Application
Note AN-2038 for more details4.
PRODUCT SELECTION
FTLF1323P1xTR
x
W
Wide Extraction Bail
B
Narrow Extraction Bail
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 2
I. Pin Descriptions
Pin
Symbol
Name/Description
Ref.
1
VEET
Trans mitter Grou nd (Common with Receiver Ground)
1
2
TFAULT
Transmitter Fault. Not supported.
3
TDIS
Transmitter Disable. Laser output disabled on high or open.
2
4
MOD_DEF(2)
Module Defi nition 2. Data line for Serial ID .
3
5
MOD_DEF(1)
Module Defi nition 1. Clock li ne for Se rial ID.
3
6
MOD_DEF(0)
Module Definit ion 0. Grounded within the module.
3
7
Rate Select
No connection required
4
8
LOS
Loss of Signal ind ica tion. Lo gic 0 ind ic a te s normal operation.
5
9
VEER
Receiver Ground (Common with Transmitter Ground)
1
10
VEER
Receiver Ground (Common with Transmitter Ground)
1
11
VEER
Receiver Ground (Co mmon with T rans mi tter Ground)
1
12
RD-
Receiver Inverted DATA out. AC Coupled.
13
RD+
Receiver Non-inverted DATA out. AC Coupled.
14
VEER
Receiver Ground (Common with Transmitter Ground)
1
15
VCCR
Receiver Power Supply
16
VCCT
Transmitter Power Supply
17
VEET
Trans mitter Grou nd (Common with Receiver Ground)
1
18
TD+
Transmitter Non-Inverted DATA in. AC Coupled.
19
TD-
Transmitter Inverted DATA in. AC Couple d.
20
VEET
Trans mitter Grou nd (Common with Receiver Ground)
1
Notes:
1. Circuit ground is in te rnally isolate d from chassis gro und.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V.
MOD_DEF( 0) pulls line low to indicate module is plugged in.
4. Finisar FTLF1323P1xTR transceivers operate between OC-3 and 125 Mbit/s without active control.
5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage
between 2.0V and 3.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Pinout of Connector Block on Host Board
VeeT
VeeT
VeeR
VeeR
TD-
TD+
RD+
RD-
VccT
VccR
VeeT
VeeR
TXFault
MOD-DEF(2)
MOD-DEF(1)
MOD-DEF(0)
Rate Select
LOS
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
Towards
ASIC
Towards
Bezel
TX Disable
VeeR
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 3
II. Absolute Maximum Ratings
Symbol
Min
Typ
Max
Unit
Ref.
Vcc
-0.5
4.5
V
TS
-40
100
°C
TOP
-40
85
°C
RH
0
85
%
1
III. Electrical Characteristics (TOP = -40 to 85
°
C, VCC = 3.10 to 3.50 Volts)
Symbol
Min
Typ
Max
Unit
Ref.
Vcc
3.10
3.50
V
Icc
165
300
mA
Transmitter
Rin
100
2
Vin,pp
250
1200
mV
VD
Vcc 1.3
Vcc
V
VEN
Vee
Vee+ 0.8
V
3
10
µs
Receiver
Vout,pp
300
400
800
mV
4
tr
250
500
ps
5
VLOS fault
Vcc 0.5
VccHOST
V
6
VLOS norm
Vee
Vee+0.5
V
6
PSR
100
mVpp
7
Notes:
1. Non condensing
2. AC coupled.
3. Or open circ uit.
4. Into 100 ohm differential termination.
5. 20 80 %
6. Loss Of Signal is LVTTL. Logic 0 ind ic ate s normal ope ration; logic 1 indicates no signal detected.
7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5
MHz up to s peci fi ed value a pplied through the power supply filt ering network shown on page 23 of the
Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000.
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 4
IV. Optical Characteristics (TOP = -40 to 85
°
C, VCC = 3.10 to 3.50 Volts)
Symbol
Min
Typ
Max
Unit
Ref.
Transmitter
POUT
-15
-8
dBm
1
λ
1261
1360
nm
σ
7.7
nm
ER
8.2
dB
tr/ tf
500
ps
2
RIN
-120
dB/Hz
JTXp-p
0.07
UI
3
JTXrms
0.007
UI
3
20%
Receiver
RSENS1
-28
-8
dBm
4
RSEN2
-28
-8
dBm
4
λC
1260
1600
nm
LOSD
-28
dBm
LOSA
-45
dBm
0.5
dB
Notes:
1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
2. Unfiltered, 20-80%
3. Jitt er mea s ure ments taken using Agilent OMN IBERT 718 in accordance with GR-253.
4. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern.
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 5
V. General Specifications
Parameter
Symbol
Min
Typ
Max
Units
Ref.
Data Rate
BR
125
155
Mb/sec
1
Bit Error Rate
BER
10-12
2
Max. S upported Link Length on
9/125µm SMF @ OC-3
L
MAX5
15
km
4
Notes:
1. Compliant wit h SONE T and S DH a t the following rate s: OC-3 IR-1/STM S-1.1 and
OC-3 SR/STM I-1.
2. Tested with a PRBS 223-1 test p a tte r n.
3. Attenuati on of 0.55 dB/km is us ed for the link length calculati ons (per G R-253 CORE). Distances are
indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link
budget based on specific conditions in your application.
VI. Environmental Specifications
Finisar 1310nm SFP transceivers have an industrial operating temperature range from
–40°C to +85°C case temperature.
Parameter
Symbol
Min
Typ
Max
Units
Ref.
Case Operating Temperature
T
op
-40
85
°C
Storage Temperature
T
sto
-40
100
°C
VII. Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of
EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 6
VIII. Digital Diagnostic Functions
Finisar FTLF1323P1xTR SFP transceivers support the 2-wire serial communication
protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in
the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic
monitoring interface, which allows real-time access to device operating parameters such
as transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory-set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note
AN-2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
SFP transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation1 or Finisar Application
Note AN-2030.
Digital diagnostics for the FTLF1323P1xTR are externally calibrated by default.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 7
IX. Mechanical Specifications
Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the
dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTLF1323P1BTR
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 8
FTLF1323P1WTR
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 9
X. PCB Layout and Bezel Recommendations
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 10
FTLF1323P1xTR Product Specificatio n
Finisar Corpor ation August 2015 Rev. B1 Page 11
XI. References
1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),
September 2000. Documentation is currently available at Finisar upon request.
2. Bellcore GR-253 and ITU-T G.957 Specifications.
3. Directive 2011/65/EU of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electronic equipment”. Certain products may use one or more exemptions as
allowed by the Directive.
4. “Application Note AN-2038: Finisar Implementation of RoHS Compliant
Transceivers”.
XII. For More Information
Finisar Corporation
1389 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
sales@finisar.com
www.finisar.com