Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 1 of 17
Features
• 12 parallel channels, total 32.6 Gbps
capacity
• Data rate up to 2.72 Gbps per channel
• 850 nm VCSEL array
• Link reach 300 m with 50/125μm 500
MHz.km fiber at 2.5 Gbps
• Channel BER better than 10-12
• Industry standard MPO/MTP™ ribbon fiber
connector interface
• Pluggable MegArray® ball grid array
connector
• Laser class 1M IEC 60825-1:2001
compliant
• Power supply 3.3 V
• Compatible with industry MSA
Applications
• High-speed interconnects within and
between switches, routers and transport
equipment
• Low cost SONET/SDH VSR (Very Short
Reach) OC-192/STM64 connections
• InfiniBand® connections
• Interconnects rack-to-rack, shelf-to-shelf,
board-to-board, board-to-optical backplane
Description
The ZL60101 and ZL60102 together make a
high speed transmitter/receiver pair for
parallel fiber applications.
The ZL60101 transmitter module converts
parallel electrical input signals via a laser
driver and a VCSEL array into parallel
optical output signals at a wavelength
of 850 nm.
The ZL60102 receiver module converts
parallel optical input signals via a PIN
photodiode array and a transimpedance and
limiting amplifier into electrical
output signals.
The modules are pluggable each fitted with
an industry standard MegArray® BGA
connector. This provides ease of assembly
on the host board and enables provisioning
of bandwidth on demand.
Reliability assurance is based on Telcordia
GR-468-CORE and the parts are compliant
to the EU directive 2002/95/EC issued 27
January 2003 [RoHS].
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 2 of 17
Table of Contents
Features .......................................................................................................................................... 1
Applications ................................................................................................................................... 1
Description ...................................................................................................................................... 1
Absolute Maximum Ratings .......................................................................................................... 3
Recommended Operating Conditions .......................................................................................... 3
ZL60101 Transmitter Specifications ............................................................................................. 4
Transmitter Control and Status Signals ............................................................................... 6
Transmitter Control and Status Timing Diagrams ............................................................... 7
Transmitter Pin out Assignments......................................................................................... 9
Transmitter Pin Description ............................................................................................... 10
ZL60102 Receiver Specifications ................................................................................................ 11
Receiver Control and Status Signals ................................................................................. 12
Receiver Control and Status Timing Diagrams ................................................................. 13
Receiver Pin out Assignments........................................................................................... 14
Receiver Pin Description ................................................................................................... 15
Handling instructions ................................................................................................................... 16
Cleaning the Optical Interface ........................................................................................... 16
Connectors ........................................................................................................................ 16
ESD Handling .................................................................................................................... 16
Link Reach ..................................................................................................................................... 17
Link Model Parameters ...................................................................................................... 17
Trademarks ................................................................................................................................... 17
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 3 of 17
Absolute Maximum Ratings
Not necessarily applied together. Exceeding these values may cause permanent damage.
Functional operation under these conditions is not implied.
Recommended Operating Conditions
These parameters apply both to the transmitter and the receiver.
Figure 1 - Recommended Power Supply Filter
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 4 of 17
ZL60101 Transmitter Specifications
All parameters below require operating conditions according to “Recommended Operating
Conditions” on page 3.
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 5 of 17
Classified in accordance with IEC 60825-1/A2:2001, IEC 60825-2 : 2000
Class 1M Laser Product
Emitted wavelength: 840 nm
Figure 2 - ZL60101 Transmitter Block Diagram
Table 1 - Transmitter Optical Channel Assignment
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 6 of 17
Transmitter Control and Status Signals
The following table shows the timing relationships of the status and control signals of the
pluggable optical transmitter.
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 7 of 17
Transmitter Control and Status Timing Diagrams
The following figures show the timing relationships of the status and control signals of the
pluggable optical transmitter.
Figure 3 - Transmitter Power-up Sequence.
Figure 4 - Transmitter Fault Signal Timing Diagram
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 8 of 17
Figure 5 - Transmitter Reset Signal Timing Diagram
Figure 6 - Transmitter Enable and Disable Timing Diagram
Table 2 - Truth Table for Transmitter Operation (Pre-condition: RESET floating or HIGH)
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 9 of 17
Transmitter Pin out Assignments
Table 3 - Transmitter Host Circuit Board Layout (Top view, toward MPO/MTP™ connector
end) (10x10 array, 1.27 mm pitch)
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 10 of 17
Transmitter Pin Description
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 11 of 17
ZL60102 Receiver Specifications
All parameters below require operating conditions according to “Recommended Operating
Conditions,” on page 3 and a termination load of 100 Ω differential at the electrical output.
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 12 of 17
Figure 7 - ZL60102 Receiver Block Diagram
Table 4 - Receiver Optical Channel Assignment
Receiver Control and Status Signals
The following table shows the timing relationships of the status and control signals of the
pluggable optical receiver.
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 13 of 17
Receiver Control and Status Timing Diagrams
The following figures show the timing relationships of the status and control signals of the
pluggable optical receiver.
Figure 8 - Receiver Enable Signal Timing Diagram
Figure 9 - Receiver Signal Detect Timing Diagram
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 14 of 17
Receiver Pin out Assignments
Table 5 - Receiver Pin out Assignments (Top view, toward MPO/MTP™ connector end)
(10x10 array, 1.27 mm pitch)
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 15 of 17
Receiver Pin Description
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 16 of 17
Handling instructions
Cleaning the Optical Interface
A protective connector plug is supplied with each module. This plug should remain in place
whenever a fiber cable is not inserted. This will keep the optical port free from dust or other
contaminants, which may potentially degrade the optical signal. Before reattaching the connector
plug to the module, visually inspect the plug and remove any contamination. If the module’s
optical port becomes contaminated, it can be cleaned with high-pressure nitrogen
(the use of fluids, or physical contact, is not advised due to potential for damage).
Before a fiber cable connector is attached to the module, it is recommended to clean the fiber
cable connector using an optical connector cleaner, or according to the cable manufacturer's
instructions. It is also recommended to clean the optical port of the module with high-pressure
nitrogen.
Connectors
For optimum performance, it is recommended that the number of insertions is limited to 50 for the
electrical MegArray connector and 200 for the optical MPO/MTP connector.
ESD Handling
When handling the modules, precautions for ESD sensitive devices should be taken. These
include use of ESD protected work areas with wrist straps, controlled work-benches, floors etc.
Customer Drawing
2.7 Gb/s 12-ch
Parallel Fiber Transmitter and Receiver
ZL60101MLDL, ZL60102MLDL
November 2010
Tyco Electronics Nederland B.V. This information is confidential and propriety to Tyco This specification is a controlled document and subject to
Electronics and its worldwide subsidiaries and affiliates. change. Contact the Engineering Control Organization for
All international rights reserved It may not be disclosed to anyone, other than Tyco the latest revision.
Tyco Electronics Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 03-07) 17 of 17
Link Reach
The following table lists the minimum reach distance of the 12 channel pluggable optical modules
for different multimode fiber (MMF) types and bandwidths assuming worst case parameters. Each
case allows for a maximum of 2 dB per channel connection loss for patch cables and other
connectors.
Table 6 - Link Reach for Different Fiber Types and Data Rates
Longer operating distance than the range specified here can be achieved using transmitters,
receivers and / or cables meeting specification but performing better than worst case.
Link Model Parameters
The link reaches above have been calculated using the following link model parameters and
Gigabit Ethernet link model version 2.3.5 (filename: 5pmd047.xls).
Trademarks
Infiniband is a registered trademark of the InfiniBand Trade Association.
MTP is a registered trademark of US Conec Ltd.
The MegArray is a registered trademark of FCI.
