LTC3838 Dual, Fast, Accurate StepDown DC/DC Controller with Differential Output Sensing Description Features n n n n n n n n n n n n n Wide VIN Range: 4.5V to 38V, VOUT: 0.6V to 5.5V 0.67% Output Voltage Accuracy Over Temperature, Differential Output Voltage Sensing, Allowing Up to 500mV Line Loss at Remote Ground on Channel 1 1% Output on the Independent 2nd Channel Controlled On-Time, Valley Current Mode Control Fast Load Transient Response Detect Transient (DTR) Reduces VOUT Overshoot Frequency Programmable from 200kHz to 2MHz, Synchronizable to External Clock tON(MIN) = 30ns, tOFF(MIN) = 90ns RSENSE or Inductor DCR Current Sensing Overvoltage Protection and Current Limit Foldback Power Good Output Voltage Monitor Output Voltage Tracking and Adjustable Soft Start-Up Thermally Enhanced 38-Pin (5mm x 7mm) QFN and TSSOP packages Applications n n n n Distributed Power Systems Point-of-Load Converters Computing Systems Data Communication Systems The LTC(R)3838 is a dual, PolyPhase(R) synchronous step-down DC/DC switching regulator controller. Two independent channels drive all N-channel power MOSFETs. The controlled on-time, valley current mode control architecture allows for fast transient response and constant frequency switching in steady-state operation, independent of VIN, VOUT and load current. Its load-release transient detection feature significantly reduces overshoot at low output voltages. Differential output voltage sensing, along with a precision internal reference, offers an accurate 0.67% output regulation on Channel 1, even if the remote output ground deviates from local ground by 500mV. The second channel can either provide an independent 1% output, or together with the first channel of this controller, serve as one of the PolyPhase channels for a single-output voltage. The switching frequency can be programmed from 200kHz to 2MHz with an external resistor, and can be synchronized to an external clock. Very low tON and tOFF times allow for near 0% and near 100% duty cycles, respectively. Voltage tracking soft start-up and multiple safety features are provided. L, LT, LTC, LTM, PolyPhase, OPTI-LOOP, Module, Linear Technology and the Linear logo are registered trademarks and No RSENSE and UltraFast are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 5847554, 6580258, 6304066, 6476589, 6774611. Typical Application 1.2V/1.5V, 15A, 350kHz, DCR Sense, Step-Down Converter (Refer to Figure 16 for Full Design) Efficiency/Power Loss VIN 4.5V TO 38V VIN INTVCC TG1 TG2 0.1F x2 4.7F 10k LTC3838 SW2 BOOST1 BOOST2 DRVCC1 DRVCC2 BG1 BG2 0.56H 0.1F 15k VOUT2 1.5V 15A + 10k 330F x2 PGND VOUTSENSE1+ VOUTSENSE1- TRACK/SS1 TRACK/SS2 115k ITH1 RT SGND 2.0 80 1.5 EFFICIENCY 70 POWER LOSS 60 1.0 0.5 50 40 VFB2 2.5 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 90 EFFICIENCY (%) 10k SENSE2+ SW1 0.56H + 330F SENSE2- SENSE1+ POWER LOSS (W) VOUT1 1.2V 15A SENSE1- 100 VIN = 12V VOUT = 1.2V 0.1 1 LOAD CURRENT (A) 10 0 3838 F16b ITH2 3838 TA01a 3838fb For more information www.linear.com/LTC3838 1 LTC3838 Absolute Maximum Ratings (Note 1) VIN Voltage.................................................. -0.3V to 40V BOOST1, BOOST2 Voltages........................ -0.3V to 46V SW1, SW2 Voltages....................................... -5V to 40V INTVCC, DRVCC1, DRVCC2, EXTVCC, PGOOD1, PGOOD2, RUN1, RUN2, (BOOST1-SW1), (BOOST2-SW2), MODE/PLLIN Voltages....... -0.3V to 6V VOUTSENSE1+, VOUTSENSE1-, SENSE1+, SENSE2+, SENSE1-, SENSE2- Voltages........................ -0.6V to 6V TRACK/SS1, TRACK/SS2 Voltages............... -0.3V to 5V DTR1, DTR2, PHASMD, RT, VRNG1, VRNG2, VFB2, ITH1, ITH2 Voltages................. -0.3V to (INTVCC + 0.3V) Operating Junction Temperature Range (Note 2, 3, 4)........................................... -40C to 125C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec) FE Package........................................................ 300C Pin Configuration TOP VIEW BOOST2 PGOOD2 RUN2 DTR2 SENSE2- SENSE2+ VFB2 TOP VIEW 38 37 36 35 34 33 32 TRACK/SS2 1 31 TG2 ITH2 2 30 SW2 VRNG2 3 29 BG2 PHASMD 4 28 DRVCC2 MODE/PLLIN 5 27 EXTVCC CLKOUT 6 26 INTVCC 39 PGND SGND 7 25 PGND DTR2 1 38 RUN2 SENSE2- 2 37 PGOOD2 SENSE2+ 3 36 BOOST2 VFB2 4 35 TG2 TRACK/SS2 5 34 SW2 ITH2 6 33 BG2 VRNG2 7 32 DRVCC2 PHASMD 8 31 EXTVCC MODE/PLLIN 9 CLKOUT 10 SGND 11 24 VIN RT 8 RT 12 23 DRVCC1 VRNG1 9 39 PGND 30 INTVCC 29 PGND 28 VIN 27 DRVCC1 22 BG1 VRNG1 13 26 BG1 TRACK/SS1 11 21 SW1 ITH1 14 25 SW1 VOUTSENSE1+ 12 20 TG1 TRACK/SS1 15 24 TG1 BOOST1 PGOOD1 RUN1 22 PGOOD1 DTR1 23 BOOST1 VOUTSENSE1- 17 SENSE1- VOUTSENSE1+ 16 SENSE1+ 13 14 15 16 17 18 19 VOUTSENSE1- ITH1 10 UHF PACKAGE 38-LEAD (5mm x 7mm) PLASTIC QFN TJMAX = 125C, JA = 34C/W EXPOSED PAD (PIN 39) IS PGND, MUST BE SOLDERED TO PCB SENSE1+ 18 21 RUN1 SENSE1- 20 DTR1 19 FE PACKAGE 38-LEAD PLASTIC TSSOP TJMAX = 125C, JA = 28C/W EXPOSED PAD (PIN 39) IS PGND, MUST BE SOLDERED TO PCB Table 1. Comparison of LTC3838 Options PART NUMBER DESCRIPTION LTC3838 0.67% Differential Output Regulation on Channel 1 1% Output Regulation on Channel 2 Separate-Per-Channel Continuous 30mV to 100mV Current Sense Range Controls LTC3838-1 0.67% and 0.75%, Both Differential Output Regulation on Channel 1 and 2 Single-Pin 30mV/60mV Current Sense Range Control, Improved Current Limit Accuracy Than LTC3838 LTC3838-2 0.67% Differential Output Regulation with Internal Reference on Channel 1 4mV Differential Output Regulation with External Reference Voltage on Channel 2 Fixed 30mV Current Sense Range, Improved Current Limit Accuracy Than LTC3838 3838fb 2 For more information www.linear.com/LTC3838 LTC3838 Order Information (http://www.linear.com/product/LTC3838#orderinfo) LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3838EUHF#PBF LTC3838EUHF#TRPBF 3838 38-Lead (5mm x 7mm) Plastic QFN -40C to 125C LTC3838IUHF#PBF LTC3838IUHF#TRPBF 3838 38-Lead (5mm x 7mm) Plastic QFN -40C to 125C LTC3838EFE#PBF LTC3838EFE#TRPBF LTC3838FE 38-Lead Plastic TSSOP -40C to 125C LTC3838IFE#PBF LTC3838IFE#TRPBF LTC3838FE 38-Lead Plastic TSSOP -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/. Some packages are available in 500 unit reels through designated sales channels with #TRMPBF suffix. Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 15V unless otherwise noted (Note 3). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Main Control Loops VIN Input Voltage Operating Range 4.5 38 V VOUT1,2(REG) Regulated Output Voltage Operating Range VOUT1 Regulated Differentially with Respect to VOUTSENSE1-, VOUT2 Regulated with Respect to SGND 0.6 5.5 V IQ Input DC Supply Current Both Channels Enabled Only One Channel Enabled Shutdown Supply Current MODE/PLLIN = 0V, No Load RUN1 or RUN2 (But Not Both) = 0V RUN1 = RUN2 = 0V VOUTSENSE1(REG) Regulated Differential Feedback Voltage on ITH1 = 1.2V (Note 5) Channel 1 (VOUTSENSE1+ - VOUTSENSE1-) TA = 25C TA = 0C to 85C TA = -40C to 125C 3 2 15 mA mA A l l 0.5985 0.596 0.594 0.6 0.6 0.6 0.6015 0.604 0.606 V V V l l 0.594 0.591 0.6 0.6 0.606 0.609 V V ITH2 = 1.2V (Note 5) TA = 25C TA = 0C to 85C TA = -40C to 125C l l 0.597 0.594 0.592 0.6 0.6 0.6 0.603 0.606 0.608 V V V Regulated Feedback Voltage on Channel 2 Over Line, Load VIN = 4.5V to 38V, ITH2 = 0.5V to 1.9V (Note 5) TA = 0C to 85C TA = -40C to 125C l l 0.592 0.588 0.6 0.6 0.608 0.612 V V IVOUTSENSE1+ VOUTSENSE1+ Input Bias Current VOUTSENSE1+ - VOUTSENSE1- = 0.6V 5 25 nA IVOUTSENSE1- VOUTSENSE1 - Input Bias Current VOUTSENSE1+ - VOUTSENSE1- = 0.6V -25 -50 A IVFB2 VFB2 Input Bias Current VFB2 = 0.6V -5 50 nA Regulated Differential Feedback Voltage on VIN = 4.5V to 38V, ITH1 = 0.5V to 1.9V (Note 5), Channel 1 Over Line, Load and Common -0.5V < VOUTSENSE1- < 0.5V Mode TA = 0C to 85C TA = -40C to 125C VFB2(REG) Regulated Feedback Voltage on Channel 2 gm(EA)1,2 Error Amplifier Transconductance ITH = 1.2V (Note 5) 1.7 mS tON(MIN)1,2 Minimum Top Gate On-Time VIN = 38V, VOUT = 0.6V, RT = 20k (Note 6) 30 ns tOFF(MIN)1,2 Minimum Top Gate Off-Time (Note 6) 90 ns 3838fb For more information www.linear.com/LTC3838 3 LTC3838 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 15V unless otherwise noted (Note 3). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VSENSE(MAX)1,2 Maximum Valley Current Sense Threshold (VSENSE1,2+ - VSENSE1,2-) VRNG = 2V, VFB = 0.57V, VSENSE- = 2.5V VRNG = 0V, VFB = 0.57V, VSENSE- = 2.5V VRNG = INTVCC, VFB = 0.57V, VSENSE- = 2.5V 80 21 39 100 30 50 120 40 61 mV mV mV VSENSE(MIN)1,2 Minimum Valley Current Sense Threshold (VSENSE1,2+ - VSENSE1,2-) (Forced Continuous Mode) VRNG = 2V, VFB = 0.63V, VSENSE- = 2.5V VRNG = 0V, VFB = 0.63V, VSENSE- = 2.5V VRNG = INTVCC, VFB = 0.63V, VSENSE- = 2.5V -50 -15 -25 ISENSE1,2+ SENSE1,2+ Pins Input Bias Current VSENSE+ = 0.6V VSENSE+ = 5V 5 1 ISENSE1,2- SENSE1,2- Pins Input Bias Current (Internal 500k Resistor to SGND) VSENSE- = 0.6V VSENSE- = 5V 1.2 10 Current Sensing l l l mV mV mV 50 2 nA A A A Start-Up and Shutdown VRUN1,2 RUN Pin On Threshold VRUN1,2 Rising RUN Pin On Hysteresis VRUN1,2 Falling from On Threshold 100 mV 1.2 A 5 A RUN Pin Pull-Up Current when Off RUN1,2 = SGND RUN Pin Pull-Up Current Hysteresis IRUN1,2(HYS) = IRUN1,2(ON) - IRUN1,2(OFF) UVLO INTVCC Undervoltage Lockout INTVCC Falling INTVCC Rising ITRACK/SS1,2 Soft-Start Pull-Up Current 0V < TRACK/SS1,2 < 0.6V IRUN1,2 l l l 1.1 3.3 1.2 3.7 4.2 1.3 4.5 1 V V V A Frequency and Clock Synchronization f Clock Output Frequency (Steady-State Switching Frequency) RT = 205k RT = 80.6k RT = 18.2k Channel 2 Phase (Relative to Channel 1) PHASMD = SGND PHASMD = Floating PHASMD = INTVCC 180 180 240 Deg Deg Deg CLKOUT Phase (Relative to Channel 1) PHASMD = SGND PHASMD = Floating PHASMD = INTVCC 60 90 120 Deg Deg Deg 450 200 500 2000 550 kHz kHz kHz VPLLIN(H) Clock Input High Level Into MODE/PLLIN VPLLIN(L) Clock Input Low Level Into MODE/PLLIN RMODE/PLLIN MODE/PLLIN Input DC Resistance With Respect to SGND 600 k RTG(UP)1,2 TG Driver Pull-Up On Resistance TG High 2.5 RTG(DOWN)1,2 TG Driver Pull-Down On Resistance TG Low 1.2 RBG(UP)1,2 BG Driver Pull-Up On Resistance BG High 2.5 RBG(DOWN)1,2 BG Driver Pull-Down On Resistance BG Low 0.8 tD(TG/BG)1,2 Top Gate Off to Bottom Gate On Delay Time (Note 6) 20 ns tD(BG/TG)1,2 Bottom Gate Off to Top Gate On Delay Time (Note 6) 15 ns 2 V 0.5 V Gate Drivers 3838fb 4 For more information www.linear.com/LTC3838 LTC3838 Electrical Characteristics The l denotes the specifications which apply over the specified operating junction temperature range, otherwise specifications are at TA = 25C. VIN = 15V unless otherwise noted (Note 3). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Internally Regulated DRVCC1 Voltage 6V < VIN < 38V 5.0 5.3 5.6 V DRVCC1 Load Regulation IDRVCC1 = 0mA to -100mA -1.5 -3 % EXTVCC Switchover Voltage EXTVCC Rising 4.6 4.8 Internal VCC Regulator VDRVCC1 VEXTVCC 4.4 EXTVCC Switchover Hysteresis V 200 mV 200 mV EXTVCC to DRVCC2 Voltage Drop VEXTVCC = 5V, IDRVCC2 = -100mA OV PGOOD Overvoltage Threshold VFB1,2 Rising, with Respect to Regulated Voltage 5 7.5 10 % UV PGOOD Undervoltage Threshold VFB1,2 Falling, with Respect to Regulated Voltage -5 -7.5 -10 % PGOOD Threshold Hysteresis VFB1,2 Returning to Reference Voltage VPGOOD(L)1,2 PGOOD Low Voltage IPGOOD = 2mA tD(PGOOD)1,2 Delay from VFB Fault (OV/UV) to PGOOD Falling Delay from VFB Good to PGOOD Rising PGood Output Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The junction temperature (TJ, in C) is calculated from the ambient temperature (TA, in C) and power dissipation (PD, in Watts) according to the formula: TJ = TA + (PD * JA) where JA (in C/W) is the package thermal impedance. Note 3: The LTC3838 is tested under pulsed loading conditions such that TJ TA. The LTC3838E is guaranteed to meet specifications over the 0C to 85C operating junction temperature range. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3838I is guaranteed to meet specifications over the -40C to 125C operating junction temperature range . Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. 2 0.1 % 0.3 V 50 s 20 s Note 4: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. Note 5: The LTC3838 is tested in a feedback loop that adjusts (VOUTSENSE1+ - VOUTSENSE1-) or VFB2 to achieve specified error amplifier output voltages (ITH1,2). Note 6: Delay times are measured with top gate (TG) and bottom gate (BG) driving minimum load, and using 50% levels. 3838fb For more information www.linear.com/LTC3838 5 LTC3838 Typical Performance Characteristics Transient Response (Forced Continuous Mode) Load Step (Forced Continuous Mode) Load Release (Forced Continuous Mode) ILOAD 10A/DIV ILOAD 10A/DIV ILOAD 10A/DIV VOUT 50mV/DIV AC-COUPLED VOUT 50mV/DIV AC-COUPLED VOUT 50mV/DIV AC-COUPLED IL 10A/DIV IL 10A/DIV IL 10A/DIV 3838 G01 50s/DIV LOAD TRANSIENT = 0A TO 15A TO 0A VIN = 12V VOUT = 1.2V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND 3838 G02 5s/DIV LOAD STEP = 0A TO 15A VIN = 12V VOUT = 1.2V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND 3838 G03 5s/DIV LOAD RELEASE = 15A TO 0A VIN = 12V VOUT = 1.2V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Transient Response (Discontinuous Mode) Load Step (Discontinuous Mode) Load Release (Discontinuous Mode) ILOAD 10A/DIV ILOAD 10A/DIV VOUT 50mV/DIV AC-COUPLED VOUT 50mV/DIV AC-COUPLED IL 10A/DIV IL 10A/DIV 3838 G04 50s/DIV LOAD TRANSIENT = 500mA TO 15A TO 500mA VIN = 12V VOUT = 1.2V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND ILOAD 10A/DIV VOUT 50mV/DIV AC-COUPLED IL 10A/DIV 3838 G05 5s/DIV LOAD STEP = 500mA TO 15A VIN = 12V VOUT = 1.2V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Load Release with Detect Transient (DTR) Feature Enabled 3838 G06 5s/DIV LOAD RELEASE = 15A TO 500mA VIN = 12V VOUT = 1.2V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Load Release with Detect Transient (DTR) Feature Disabled SW 3V/DIV SW 3V/DIV VOUT 50mV/DIV AC-COUPLED ITH 1V/DIV VOUT 50mV/DIV AC-COUPLED IL 10A/DIV IL 10A/DIV ITH 1V/DIV 5s/DIV LOAD RELEASE = 15A TO 5A VIN = 5V VOUT = 0.6V 3838 G07 LOAD RELEASE = 15A TO 5A VIN = 5V VOUT = 0.6V FIGURE 17 CIRCUIT, CHANNEL 1 MODIFIED: RFB2 = 0, VRNG2 = SGND, CITH1 = 120pF, CITH2 = 0pF, FROM DTR1 PIN: RITH1 = 46.4k TO SGND, RITH2 = 42.2k TO INTVCC 5s/DIV 3838 G08 FIGURE 17 CIRCUIT, CHANNEL 1 MODIFIED: RFB2 = 0, VRNG2 = SGND, CITH1 = 120pF, CITH2 = 0pF, RITH1/2 = 46.4k TO SGND//42.2k TO INTVCC, CONNECTION FROM RITH1/2 AND CITH1 TO DTR1 PIN REMOVED. DTR1 PIN TIED TO INTVCC 3838fb 6 For more information www.linear.com/LTC3838 LTC3838 Typical Performance Characteristics Soft Start-Up Into Pre-Biased Output Regular Soft Start-Up RUN1 5V/DIV RUN1 5V/DIV TRACK/SS1 200mV/DIV VOUT 500mV/DIV TRACK/SS1 200mV/DIV 3838 G09 CSS = 10nF 1ms/DIV VIN = 12V VOUT = 1.2V FORCED CONTINUOUS MODE FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND 3838 G10 CSS = 10nF 1ms/DIV VIN = 12V VOUT = 1.2V VOUT PRE-BIASED TO 0.75V FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Overcurrent Protection Overvoltage Protection SHORTCIRCUIT TRIGGER IL 10A/DIV VOUT 1V/DIV FULL CURRENT LIMIT WHEN VOUT HIGHER THAN HALF OF REGULATED CURRENT LIMIT STARTS TO FOLD BACK AS VOUT DROPS BELOW HALF OF REGULATED IL 10A/DIV VOUT 100mV/DIV AC-COUPLED 3838 G12 VIN = 12V 5ms/DIV VOUT = 1.2V FORCED CONTINUOUS MODE CURRENT LIMIT = 17A OVERLOAD = 7.5A TO 17.5A FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND OVERVOLTAGE CREATED BY APPLYING A CHARGED CAPACITOR TO VOUT VOUT 100mV/DIV AC-COUPLED COUT RECHARGE 3838 G13 VIN = 12V 500s/DIV VOUT = 1.2V ILOAD = 0A FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Phase Relationship: PHASMD = Ground BG1 5V/DIV 3838 G14 VIN = 12V 20s/DIV VOUT = 1.2V BG STAYS ON UNTIL FORCED CONTINUOUS VOUT IS PULLED BELOW OVERVOLTAGE MODE THRESHOLD ILOAD = 0A FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Phase Relationship: PHASMD = Float PLLIN 5V/DIV Phase Relationship: PHASMD = INTVCC PLLIN 5V/DIV SW1 10V/DIV 0 SW2 10V/DIV 3838 G11 VIN = 12V 10ms/DIV VOUT = 1.2V FORCED CONTINUOUS MODE FIGURE 17 CIRCUIT, CHANNEL 1, VRNG1 = SGND Short-Circuit Protection IL 5A/DIV CLKOUT 5V/DIV TRACK/SS1 200mV/DIV VOUT 500mV/DIV VOUT 500mV/DIV SW1 10V/DIV Output Tracking PLLIN 5V/DIV SW1 10V/DIV 0 SW2 10V/DIV 180 60 3838 G15 500ns/DIV FIGURE 19 CIRCUIT VIN = 12V VOUT1 = 5V, VOUT2 = 3.3V LOAD = 0A MODE/PLLIN = 333kHz EXTERNAL CLOCK CLKOUT 5V/DIV 0 SW2 10V/DIV 180 90 3838 G15 500ns/DIV FIGURE 19 CIRCUIT VIN = 12V VOUT1 = 5V, VOUT2 = 3.3V LOAD = 0A MODE/PLLIN = 333kHz EXTERNAL CLOCK CLKOUT 5V/DIV 240 120 3838 G17 500ns/DIV FIGURE 19 CIRCUIT VIN = 12V VOUT1 = 5V, VOUT2 = 3.3V LOAD = 0A MODE/PLLIN = 333kHz EXTERNAL CLOCK 3838fb For more information www.linear.com/LTC3838 7 LTC3838 Typical Performance Characteristics Output Regulation vs Input Voltage NORMALIZED VOUT (%) 0.1 NORMALIZED VOUT (%) 0.2 VOUT = 0.6V ILOAD = 5A VOUT NORMALIZED AT VIN = 15V 0 -0.1 -0.2 CHANNEL 1 CHANNEL 2 0 5 10 15 20 25 VIN (V) 30 35 0.6 VIN = 15V VOUT = 0.6V VOUT NORMALIZED AT ILOAD = 4A 0.1 0 0.2 0 -0.4 CHANNEL 1 CHANNEL 2 2 0 6 4 ILOAD (A) 8 -0.6 -50 -25 10 Error Amplifier Transconductance vs Temperature 1.80 2 2 1 1 NORMALIZED f (%) NORMALIZED f (%) 1.60 0 -1 VOUT = 0.6V ILOAD = 5A f = 500kHz FREQUENCY NORMALIZED AT VIN = 15V 1.55 1.50 -50 -25 0 -2 25 50 75 100 125 150 TEMPERATURE (C) 0 5 10 20 25 VIN (V) 15 30 3838 G27 -1 -2 -50 -25 40 tON(MIN) and tOFF(MIN) vs Switching Frequency 90 tOFF(MIN) 80 70 60 30 tON(MIN) 40 30 20 0 1 2 3 VSENSE- (V) 4 6 3838 G24 0 tON(MIN) 20 VOUT = 0.6V RT ADJUSTED FOR fCLKOUT = 2MHz 10 5 50 40 30 20 VIN = 38V RT ADJUSTED FOR fCLKOUT = 2MHz 10 0 50 TIME (ns) 70 60 TIME (ns) 70 tON(MIN) tOFF(MIN) 80 60 50 25 50 75 100 125 150 TEMPERATURE (C) 100 90 tOFF(MIN) 40 0 3838 G23 100 80 0 tON(MIN) and tOFF(MIN) vs Voltage on VIN Pin 100 TIME (ns) 35 VIN = 15V, VOUT = 0.6V ILOAD = 0A f = 500kHz FREQUENCY NORMALIZED AT TA = 25C 3838 G21 tON(MIN) and tOFF(MIN) vs VOUT (Voltage on SENSE- Pin) 90 25 50 75 100 125 150 TEMPERATURE (C) CLKOUT/Switching Frequency vs Temperature 1.75 1.65 0 3838 G20 CLKOUT/Switching Frequency vs Input Voltage 1.70 CHANNEL 1 CHANNEL 2 3838 G19 3838 G18 TRANSCONDUCTANCE (mS) VIN = 15V VOUT = 0.6V 0.4 ILOAD = 0A VOUT NORMALIZED AT TA = 25C -0.2 -0.1 -0.2 40 Output Regulation vs Temperature NORMALIZED VOUT (%) 0.2 Output Regulation vs Load Current 0 5 10 15 20 25 VIN (V) 30 10 35 40 3838 G25 VIN = 38V VOUT = 0.6V 0 200 500 800 1100 1400 1700 2000 CLKOUT/SWITCHING FREQUENCY (kHz) 3838 G26 3838fb 8 For more information www.linear.com/LTC3838 LTC3838 Typical Performance Characteristics CURRENT SENSE VOLTAGE (mV) 100 80 60 40 20 0 -20 VRNG = 2V VRNG = 1V VRNG = 0.6V -40 -60 0 0.8 1.2 1.6 ITH VOLTAGE (V) 0.4 2 2.4 120 MAXIMUM CURRENT SENSE- VOLTAGE (mV) FORCED CONTINUOUS MODE VRNG = 2V 100 80 60 VRNG = 1V 40 VRNG = 0.6V 20 0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) RUN Pin Thresholds vs Temperature 0.8 RUN PIN BELOW 1.2V SWITCHING THRESHOLD 1.00 0.95 0 0.80 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 0 25 50 75 100 125 150 TEMPERATURE (C) 3838 G32 3838 G31 INTVCC Undervoltage Lockout Thresholds vs Temperature Shutdown Current Into VIN Pin vs Voltage on VIN Pin Quiescent Current Into VIN Pin vs Temperature 3.5 40 4.5 UVLO RELEASE (INTVCC RISING) 35 30 4.1 CURRENT (A) UVLO THRESHOLDS (V) 1.05 0.85 0 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 5.5 0.90 3838 G30 3.9 UVLO LOCK (INTVCC FALLING) 25 20 15 10 3.5 130C 25C -45C 5 0 1.5 2.5 3.5 4.5 SENSE PIN VOLTAGE (V) 1.10 RUN PIN ABOVE 1.2V SWITCHING THRESHOLD 3 1 3.3 -50 -25 0.5 TRACK/SS Pull-Up Currents vs Temperature 4 0.2 3.7 0 -0.5 1.15 2 4.3 VRNG = 0.6V 20 7 0.4 0 VRNG = 1V 40 1.20 5 SHUTDOWN REGION 0 -50 -25 60 8 6 CURRENT (A) RUN PIN THRESHOLDS (V) 1.2 0.6 80 3838 G22 CURRENT (A) SWITCHING REGION STAND-BY REGION VRNG = 2V 100 RUN Pull-Up Currents vs Temperature 1.6 1.0 120 3838 G29 3838 G28 1.4 Maximum Current Sense Voltage vs Voltage on SENSE- Pin 25 50 75 100 125 150 TEMPERATURE (C) 3838 G33 0 0 5 10 15 20 25 30 35 40 VIN (V) 3838 G34 QUIESCENT CURRENT (mA) 120 Maximum Current Sense Voltage vs Temperature MAXIMUM CURRENT SENSE VOLTAGE (mV) Current Sense Voltage vs ITH Voltage 3.0 BOTH CHANNELS ON 2.5 CHANNEL 1 ON ONLY 2.0 CHANNEL 2 ON ONLY 1.5 1.0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3838 G35 3838fb For more information www.linear.com/LTC3838 9 LTC3838 Pin Functions (QFN/TSSOP) PHASMD (Pin 4/Pin 8): Phase Selector Input. This pin determines the relative phases of channels and the CLKOUT signal. With zero phase being defined as the rising edge of TG1: Pulling this pin to SGND locks TG2 to 180, and CLKOUT to 60. Connecting this pin to INTVCC locks TG2 to 240 and CLKOUT to 120. Floating this pin locks TG2 to 180 and CLKOUT to 90. MODE/PLLIN (Pin 5/Pin 9): Operation Mode Selection or External Clock Synchronization Input. When this pin is tied to INTVCC, forced continuous mode operation is selected. Tying this pin to SGND allows discontinuous mode operation. When an external clock is applied at this pin, both channels operate in forced continuous mode and synchronize to the external clock. CLKOUT (Pin 6/Pin 10): Clock Output of Internal Clock Generator. Its output level swings between INTVCC and SGND. If clock input is present at the MODE/PLLIN pin, it will be synchronized to the input clock, with phase set by the PHASMD pin. If no clock is present at MODE/PLLIN, its frequency will be set by the RT pin. To synchronize other controllers, it can be connected to their MODE/PLLIN pins. SGND (Pin 7/Pin 11): Signal Ground. All small-signal analog and compensation components should be connected to this ground. Connect SGND to the exposed pad and PGND pin using a single PCB trace. RT (Pin 8/Pin 12): Clock Generator Frequency Programming Pin. Connect an external resistor from RT to SGND to program the switching frequency between 200kHz and 2MHz. An external clock applied to MODE/PLLIN should be within 30% of this programmed frequency to ensure frequency lock. When the RT pin is floating, the frequency is internally set to be slightly under 200kHz. VRNG1, VRNG2 (Pins 9, 3/Pins 13, 7): Current Sense Voltage Range Inputs. When programmed between 0.6V and 2V, the voltage applied to VRNG1,2 is twenty times (20x) the maximum sense voltage between SENSE1,2+ and SENSE1,2-, i.e., for either channel, (VSENSE+ - VSENSE-) = 0.05 * VRNG. If a VRNG is tied to SGND, the channel operates with a maximum sense voltage of 30mV, equivalent to a VRNG of 0.6V; If tied to INTVCC, a maximum sense voltage of 50mV, equivalent to a VRNG of 1V. ITH1, ITH2 (Pins 10, 2/Pins 14, 6): Current Control Threshold. This pin is the output of the error amplifier and the switching regulator's compensation point. The current comparator threshold increases with this control voltage. The voltage ranges from 0V to 2.4V, with 0.8V corresponding to zero sense voltage (zero inductor valley current). TRACK/SS1, TRACK/SS2 (Pins 11, 1/Pins 15, 5): External Tracking and Soft-Start Input. The LTC3838 regulates the feedback voltages (VOUTSENSE1+ - VOUTSENSE1-) and VFB2 to the smaller of 0.6V or the voltage on the TRACK/SS1,2 pins respectively. An internal 1A temperature-independent pull-up current source is connected to each TRACK/SS pin. A capacitor to ground at this pin sets the ramp time to the final regulated output voltage. Alternatively, another voltage supply connected to this pin allows the output to track the other supply during start-up. VOUTSENSE1+ (Pin 12/Pin 16): Differential Output Sense Amplifier (+) Input of Channel 1. Connect this pin to a feedback resistor divider between the positive and negative output capacitor terminals of VOUT1. In nominal operation the LTC3838 will attempt to regulate the differential output voltage VOUT1 to 0.6V divided by the feedback resistor divider ratio. 3838fb 10 For more information www.linear.com/LTC3838 LTC3838 Pin Functions (QFN/TSSOP) VOUTSENSE1- (Pin 13/Pin 17): Differential Output Sense Amplifier (-) Input of Channel 1. Connect this pin to the negative terminal of the output load capacitor of VOUT1. SENSE1+, SENSE2+ (Pins 14, 37/Pins 18, 3): Differential Current Sense Comparator (+) Inputs. The ITH pin voltage and controlled offsets between the SENSE+ and SENSE- pins set the current trip threshold. The comparator can be used for RSENSE sensing or inductor DCR sensing. For RSENSE sensing, Kelvin (4-wire) connect the SENSE+ pin to the (+) terminal of RSENSE. For DCR sensing, tie the SENSE+ pins to the connection between the DCR sense capacitor and sense resistor tied across the inductor. SENSE1-, SENSE2- (Pins 15, 36/Pins 19, 2): Differential Current Sense Comparator (-) Input. The comparator can be used for RSENSE sensing or inductor DCR sensing. For RSENSE sensing, Kelvin (4-wire) connect the SENSE- pin to the (-) terminal of RSENSE. For DCR sensing, tie the SENSE- pin to the DCR sense capacitor tied to the inductor VOUT node connection. These pins also function as output voltage sense pins for the top MOSFET on-time adjustment. The impedance looking into these pins is different from the SENSE+ pins because there is an additional 500k internal resistor from each of the SENSE- pins to SGND. DTR1, DTR2 (Pins 16, 35/Pins 20, 1): Detect LoadRelease Transient for Overshoot Reduction. When load current suddenly drops, if voltage on this DTR pin drops below half of INTVCC, the bottom gate (BG) could turn off, allowing the inductor current to drop to zero faster, thus reducing the VOUT overshoot. (Refer to Load-Release Transient Detection in the Applications Information section for more details.) An internal 2.5A current source pulls this pin toward INTVCC. To disable the DTR feature, simply tie the DTR pin to INTVCC. RUN1, RUN2 (Pins 17, 34/Pins 21, 38): Run Control Inputs. An internal proportional-to-absolute-temperature (PTAT) pull-up current source (~1.2A at 25C) is constantly connected to this pin. Taking both RUN1 and RUN2 pins below a threshold voltage (~0.8V at 25C) shuts down all bias of INTVCC and DRVCC and places the LTC3838 into micropower shutdown mode. Allowing either RUN pin to rise above this threshold would turn on the internal bias supply and the circuitry for the particular channel. When a RUN pin rises above 1.2V, its corresponding channel's TG and BG drivers are turned on and an additional 5A temperature-independent pull-up current is connected internally to the RUN pin. Either RUN pin can sink up to 50A, or be forced no higher than 6V. PGOOD1, PGOOD2 (Pins 18, 33/Pins 22, 37): Power Good Indicator Outputs. This open-drain logic output is pulled to ground when the output voltage goes out of a 7.5% window around the regulation point, after a 50s powerbad-masking delay. Returning to the regulation point, there is a much shorter delay to power good, and a hysteresis of around 2% on both sides of the voltage window. BOOST1, BOOST2 (Pins 19, 32/Pins 23, 36): Boosted Floating Supplies for Top MOSFET Drivers. The (+) terminal of the bootstrap capacitor, CB, connects to this pin. The BOOST pins swing by a VIN between a diode drop below DRVCC, or (DRVCC - VD) and (VIN + DRVCC - VD). TG1, TG2 (Pins 20, 31/Pins 24, 35): Top Gate Driver Outputs. The TG pins drive the gates of the top N-channel power MOSFET with a voltage swing of VDRVCC between SW and BOOST. 3838fb For more information www.linear.com/LTC3838 11 LTC3838 Pin Functions (QFN/TSSOP) SW1, SW2 (Pins 21, 30/Pins 25, 34): Switch Node Connection to Inductors. Voltage swings are from a diode voltage below ground to VIN. The (-) terminal of the bootstrap capacitor, CB, connects to this node. INTVCC (Pin 26/Pin 30): Supply Input for Internal Circuitry (Not Including Gate Drivers). Normally powered from the DRVCC pins through a decoupling RC filter to SGND (typically 2 and 1F). BG1, BG2 (Pins 22, 29/Pins 26, 33): Bottom Gate Driver Outputs. The BG pins drive the gates of the bottom Nchannel power MOSFET between PGND and DRVCC. EXTVCC (Pin 27/Pin 31): External Power Input. When EXTVCC exceeds the switchover voltage (typically 4.6V), an internal switch connects this pin to DRVCC2 and shuts down the internal regulator so that INTVCC and gate drivers draw power from EXTVCC. The VIN pin still needs to be powered up but draws minimum current. DRVCC1, DRVCC2 (Pins 23, 28/Pins 27, 32): Supplies of Bottom Gate Drivers. DRVCC1 is also the output of an internal 5.3V regulator. DRVCC2 is also the output of the EXTVCC switch. Normally the two DRVCC pins are shorted together on the PCB, and decoupled to PGND with a minimum of 4.7F ceramic capacitor, CDRVCC. VIN (Pin 24/Pin 28): Input Voltage Supply. The supply voltage can range from 4.5V to 38V. For increased noise immunity decouple this pin to SGND with an RC filter. Voltage at this pin is also used to adjust top gate on-time, therefore it is recommended to tie this pin to the main power input supply through an RC filter. PGND (Pin 25, Exposed Pad Pin 39/Pin 29, Exposed Pad Pin 39): Power Ground. Connect this pin as close as practical to the source of the bottom N-channel power MOSFET, the (-) terminal of CDRVCC and the (-) terminal of CIN. Connect the exposed pad and PGND pin to SGND pin using a single PCB trace under the IC. The exposed pad must be soldered to the circuit board for electrical and rated thermal performance. VFB2 (Pin 38/Pin 4): Error Amplifier Feedback Input for Channel 2. This pin connects the error amplifier to an external feedback resistor divider from VOUT2. In nominal operation the LTC3838 will attempt to regulate the VOUT2 to 0.6V divided by the feedback resistor divider ratio. Shorting this pin to INTVCC will disable Channel 2's error amplifier, and internally connect ITH2 to ITH1. (As a result, TRACK/SS2 is no longer functional and PGOOD2 is always pulling low.) By doing so, this part can function as a dual phase, single VOUT step-down controller, and the two channels use a single Channel 1's error amplifier for the ITH output and compensation. 3838fb 12 For more information www.linear.com/LTC3838 LTC3838 Functional Diagram VIN VIN IN EN LDO OUT SD 1-2A PTAT 5A + UVLO RUN BOOST TG DRV - + 1.2V 4.2V MT L SW EN_DRV - CB DB TG RSENSE VOUT DRVCC ~0.8V - - LOGIC CONTROL SENSE- VIN 250k FORCED CONTINUOUS MODE 250k CINTVCC DRVCC2 COUT DRVCC1 CDRVCC STOP RFB2 BG DRV BG MB RFB1 PGND PHASE DETECTOR IREV ICMP RT INTVCC ON-TIME ADJUST MODE/CLK DETECT CLOCK PLL/ GENERATOR ~4.6V START ONE-SHOT TIMER MODE/PLLIN RT EXTVCC + + + CLK1 CLK2 + - - SENSE+ SENSE- TO CHANNEL 2 CLKOUT gm INTVCC + RPGD 1A gm EA + + - 0.555V UV PGOOD TRACK/SS 0.6V CSS - + DIFFAMP (A = 1) DELAY - + VOUTSENSE1+ VOUTSENSE1- 3838 FD OV - VFB2 0.645V CHANNEL 2 ONLY SGND INTVCC 1/2 INTVCC DUPLICATE DASHED LINE BOX FOR CHANNEL 2 VRNG ITH INTVCC DTR + LOAD RELEASE DETECTION - TO LOGIC CONTROL INTVCC CITH1 CITH2 RITH2 RITH1 3838fb For more information www.linear.com/LTC3838 13 LTC3838 operation (Refer to Functional Diagram) Main Control Loop The LTC3838 is a controlled on-time, valley current mode step-down DC/DC dual controller with two channels operating out of phase. Each channel drives both main and synchronous N-channel MOSFETs. The two channels can be either configured to two independently regulated outputs, or combined into a single output. The top MOSFET is turned on for a time interval determined by a one-shot timer. The duration of the one-shot timer is controlled to maintain a fixed switching frequency. As the top MOSFET is turned off, the bottom MOSFET is turned on after a small delay. The delay, or dead time, is to avoid both top and bottom MOSFETs being on at the same time, causing shoot-through current from VIN directly to power ground. The next switching cycle is initiated when the current comparator, ICMP, senses that inductor current falls below the trip level set by voltages at the ITH and VRNG pins. The bottom MOSFET is turned off immediately and the top MOSFET on again, restarting the one-shot timer and repeating the cycle. In order to avoid shoot-through current, there is also a small dead-time delay before the top MOSFET turns on. At this moment, the inductor current hits its "valley" and starts to rise again. Inductor current is determined by sensing the voltage between SENSE+ and SENSE-, either by using an explicit resistor connected in series with the inductor or by implicitly sensing the inductor's DC resistive (DCR) voltage drop through an RC filter connected across the inductor. The trip level of the current comparator, ICMP , is proportional to the voltage at the ITH pin, with a zero-current threshold corresponding to an ITH voltage of around 0.8V. The error amplifier (EA) adjusts this ITH voltage by comparing the feedback signal to the internal 0.6V reference voltage. On Channel 1, the difference amplifier (DIFFAMP) converts the differential feedback signal (VOUTSENSE1+ - VOUTSENSE1-) to a single-ended input for the EA; Channel 2 uses VFB2 directly with respect to SGND. Output voltage is regulated so that the feedback voltage is equal to the internal 0.6V reference. If the load current increases/decreases, it causes a momentary drop/rise in the differential feedback voltage relative to the reference. The EA then moves ITH voltage, or inductor valley current setpoint, higher/lower until the average inductor current again matches the load current, so that the output voltage comes back to the regulated voltage. The LTC3838 features a detect transient (DTR) pin to detect "load-release", or a transient where the load current suddenly drops, by monitoring the first derivative of the ITH voltage. When detected, the bottom gate (BG) is turned off and inductor current flows through the body diode in the bottom MOSFET, allowing the SW node voltage to drop below PGND by the body diode's forward-conduction voltage. This creates a more negative differential voltage (VSW - VOUT) across the inductor, allowing the inductor current to drop faster to zero, thus creating less overshoot on VOUT. See Load-Release Transient Detection in Applications Information for details. Differential Output Sensing This dual controller's first channel features differential output voltage sensing. The output voltage is resistively divided externally to create a feedback voltage for the controller. The internal difference amplifier (DIFFAMP) senses this feedback voltage with respect to the output's remote ground reference to create a differential feedback voltage. This scheme eliminates any ground offsets between local ground and remote output ground, resulting in a more accurate output voltage. Channel 1 allows remote output ground to deviate as much as 500mV with respect to local ground (SGND). DRVCC/EXTVCC/INTVCC Power DRVCC1,2 are the power for the bottom MOSFET drivers. Normally the two DRVCC pins are shorted together on the PCB, and decoupled to PGND with a minimum 4.7F ceramic capacitor, CDRVCC. The top MOSFET drivers are biased from the floating bootstrap capacitors (CB1,2) which are recharged during each cycle through an external Schottky diode when the top MOSFET turns off and the SW pin swings down. The DRVCC can be powered on two ways: an internal lowdropout (LDO) linear voltage regulator that is powered 3838fb 14 For more information www.linear.com/LTC3838 LTC3838 operation (Refer to Functional Diagram) from VIN and can output 5.3V to DRVCC1. Alternatively, an internal EXTVCC switch (with on-resistance of around 2) can short the EXTVCC pin to DRVCC2. If the EXTVCC pin is below the EXTVCC switchover voltage (typically 4.6V with 200mV hysteresis, see the Electrical Characteristics Table), then the internal 5.3V LDO is enabled. If the EXTVCC pin is tied to an external voltage source greater than this EXTVCC switchover voltage, then the LDO is shut down and the internal EXTVCC switch shorts the EXTVCC pin to the DRVCC2 pin, thereby powering DRVCC and INTVCC with the external voltage source and helping to increase overall efficiency and decrease internal self heating from power dissipated in the LDO. This external power source could be the output of the step-down converter itself (if the output is programmed to higher than the switchover voltage's higher limit, 4.8V). The VIN pin still needs to be powered up but now draws minimum current. Power for most internal control circuitry other than gate drivers is derived from the INTVCC pin. INTVCC can be powered from the combined DRVCC pins through an external RC filter to SGND to filter out noises due to switching. Shutdown and Start-Up Each of the RUN1 and RUN2 pins has an internal proportional-to-absolute-temperature (PTAT) current source (around 1.2A at 25C) to pull up the pins. Taking both RUN1 and RUN2 pins below a certain threshold voltage (around 0.8V at 25C) shuts down all bias of INTVCC and DRVCC and places the LTC3838 into micropower shutdown mode with a minimum IQ at the VIN pin. The LTC3838's DRVCC (through the internal 5.3V LDO regulator or EXTVCC) and the corresponding channel's internal circuitry off INTVCC will be biased up when either or both RUN pins are pulled up above the 0.8V threshold, either by the internal pull-up current or driven directly by external voltage source such as logic gate output. A channel of the LTC3838 will not start switching until the RUN pin of the respective channel is pulled up to 1.2V. When a RUN pin rises above 1.2V, the corresponding channel's TG and BG drivers are enabled, and TRACK/ SS released. An additional 5A temperature-independent pull-up current is connected internally to the channel's respective RUN pin. To turn off TG, BG and the additional 5A pull-up current, RUN needs to be pulled down below 1.2V by about 100mV. These built-in current and voltage hystereses prevent false jittery turn-on and turn-off due to noise. Such features on the RUN pins allow input undervoltage lockout (UVLO) to be set up using external voltage dividers from VIN. The start-up of a channel's output voltage (VOUT) is controlled by the voltage on its TRACK/SS pin. When the voltage on the TRACK/SS pin is less than the 0.6V internal reference, the (differential) feedback voltage is regulated to the TRACK/SS voltage instead of the 0.6V reference. The TRACK/SS pin can be used to program the output voltage soft-start ramp-up time by connecting an external capacitor from a TRACK/SS pin to signal ground. An internal temperature-independent 1A pull-up current charges this capacitor, creating a voltage ramp on the TRACK/SS pin. As the TRACK/SS voltage rises linearly from ground to 0.6V, the switching starts, VOUT ramps up smoothly to its final value and the feedback voltage to 0.6V. TRACK/ SS will keep rising beyond 0.6V, until being clamped to around 3.7V. Alternatively, the TRACK/SS pin can be used to track an external supply like in a master slave configuration. Typically, this requires connecting a resistor divider from the master supply to the TRACK/SS pin (see the Applications Information section). TRACK/SS is pulled low internally when the corresponding channel's RUN pin is pulled below the 1.2V threshold (hysteresis applies), or when INTVCC or either of the DRVCC1,2 pins drop below their respective undervoltage lockout (UVLO) thresholds. Light Load Current Operation If the MODE/PLLIN pin is tied to INTVCC or an external clock is applied to MODE/PLLIN, the LTC3838 will be forced to operate in continuous mode. With load current less than one-half of the full load peak-to-peak ripple, the inductor current valley can drop to zero or become negative. This allows constant-frequency operation but at the cost of low efficiency at light loads. 3838fb For more information www.linear.com/LTC3838 15 LTC3838 operation (Refer to Functional Diagram) If the MODE/PLLIN pin is left open or connected to signal ground, the channel will transition into discontinuous mode operation, where a current reversal comparator (IREV) shuts off the bottom MOSFET (MB) as the inductor current approaches zero, thus preventing negative inductor current and improving light-load efficiency. In this mode, both switches can remain off for extended periods of time. As the output capacitor discharges by load current and the output voltage droops lower, EA will eventually move the ITH voltage above the zero current level (0.8V) to initiate another switching cycle. Power Good and Fault Protection Each PGOOD pin is connected to an internal open-drain Nchannel MOSFET. An external resistor or current source can be used to pull this pin up to 6V (e.g., VOUT1,2 or DRVCC). Overvoltage or undervoltage comparators (OV, UV) turn on the MOSFET and pull the PGOOD pin low when the feedback voltage is outside the 7.5% window of the 0.6V reference voltage. The PGOOD pin is also pulled low when the channel's RUN pin is below the 1.2V threshold (hysteresis applies), or in undervoltage lockout (UVLO). Note that feedback voltage of Channel 1 is sensed differentially through VOUTSENSE1+ with respect to VOUTSENSE1-, while Channel 2 is sensed through VFB2 with respect to SGND. When the feedback voltage is within the 7.5% window, the open-drain NMOS is turned off and the pin is pulled up by the external source. The PGOOD pin will indicate power good immediately after the feedback is within the window. But when a feedback voltage of a channel goes out of the window, there is an internal 50s delay before its PGOOD is pulled low. In an overvoltage (OV) condition, MT is turned off and MB is turned on immediately without delay and held on until the overvoltage condition clears. Foldback current limiting is provided if the output is below one-half of the regulated voltage, such as being shorted to ground. As the feedback approaches 0V, the internal clamp voltage for the ITH pin drops from 2.4V to around 1.27V, which reduces the inductor valley current level to about 30% of its maximum value. Foldback current limiting is disabled at start-up. Frequency Selection and External Clock Synchronization An internal oscillator (clock generator) provides phaseinterleaved internal clock signals for individual channels to lock up to. The switching frequency and phase of each switching channel is independently controlled by adjusting the top MOSFET turn-on time (on-time) through the one-shot timer. This is achieved by sensing the phase relationship between a top MOSFET turn-on signal and its internal reference clock through a phase detector, and the time interval of the one-shot timer is adjusted on a cycle-by-cycle basis, so that the rising edge of the top MOSFET turn-on is always trying to synchronize to the internal reference clock signal for the respective channel. The frequency of the internal oscillator can be programmed from 200kHz to 2MHz by connecting a resistor, RT, from the RT pin to signal ground (SGND). The RT pin is regulated to 1.2V internally. For applications with stringent frequency or interference requirements, an external clock source connected to the MODE/PLLIN pin can be used to synchronize the internal clock signals through a clock phase-locked loop (Clock PLL). The LTC3838 operates in forced continuous mode of operation when it is synchronized to the external clock. The external clock frequency has to be within 30% of the internal oscillator frequency for successful synchronization. The clock input levels should be no less than 2V for "high" and no greater than 0.5V for "low". The MODE/ PLLIN pin has an internal 600k pull-down resistor. Multichip Operations The PHASMD pin determines the relative phases between the internal reference clock signals for the two channels as well as the CLKOUT signal, as shown in Table 2. The phases tabulated are relative to zero degree (0) being defined as the rising edge of the internal reference clock signal of Channel 1. The CLKOUT signal can be used to synchronize additional power stages in a multiphase power supply solution feeding either a single high current output, or separate outputs. 3838fb 16 For more information www.linear.com/LTC3838 LTC3838 operation (Refer to Functional Diagram) The system can be configured for up to 12-phase operation with a multichip solution. Typical configurations are shown in Table 3 to interleave the phases of the channels. Table 2 PHASMD SGND FLOAT INTVCC Channel 1 0 0 0 Channel 2 180 180 240 CLKOUT 60 90 120 Table 3 NUMBER OF PHASES NUMBER OF LTC3838 PIN CONNECTIONS [PIN NAME (CHIP NUMBER)] 2 1 PHASMD(1) = FLOAT or SGND 3 2, or 1 + LTC3833 PHASMD(1) = INTVCC MODE/PLLIN(2) = CLKOUT(1) 4 2 PHASMD(1) = FLOAT PHASMD(2) = FLOAT or SGND MODE/PLLIN(2) = CLKOUT(1) 6 12 3 6 externally for single-output applications. Set PHASMD to SGND or FLOAT so that the two channels are 180 out-of-phase. Efficiency losses may be substantially reduced because the peak current drawn from the input capacitor is effectively divided by the number of phases used and power loss is proportional to the RMS current squared. A 2-phase implementation can reduce the input path power loss by up to 75%. To make a single-output converter of three or more phases, additional LTC3838 or LTC3833 chips can be used. The first chip should be tied the same way as the 2-phase above. If only one more channel of an additional LTC3838 is needed, use Channel 1 for the additional phase: * Tie the ITH1 pin to the ITH1 pin of the first chip * Tie the RUN1 pin to the RUN pins of the first chip * Tie the VOUTSENSE1+ pin to the VOUTSENSE1+ pin of the first chip PHASMD(1) = SGND PHASMD(2) = SGND MODE/PLLIN(2) = CLKOUT(1) PHASMD(3) = FLOAT or SGND MODE/PLLIN(3) = CLKOUT(2) * Tie the VOUTSENSE1- pin to the VOUTSENSE1- pin of the first chip PHASMD(1) = SGND PHASMD(2) = SGND MODE/PLLIN(2) = CLKOUT(1) PHASMD(3) = FLOAT MODE/PLLIN(3) = CLKOUT(2) PHASMD(4) = SGND MODE/PLLIN(4) = CLKOUT(3) PHASMD(5) = SGND MODE/PLLIN(5) = CLKOUT(4) PHASMD(6) = FLOAT or SGND MODE/PLLIN(6) = CLKOUT(5) If both channels are needed, the additional LTC3838 chip should be tied the same way as the first LTC3838 chip to disable the second channel's EA: * Tie the TRACK/SS1 pin to the TRACK/SS1 pin of the first chip * Tie the VFB2 pin to the chip's own INTVCC * Tie the ITH1 pin to the ITH1 pin of the first chip * Tie the RUN pins to the RUN pins of the first chip Single-Output PolyPhase Configurations To use LTC3838 for a 2-phase single output step-down controller: Tie the VFB2 pin to INTVCC, which will disable Channel 2's error amplifier and internally connect ITH2 to ITH1. Tie the compensation R-C components to the ITH1 pin. The ITH2 pin can be either left open or shorted to ITH1 externally. The TRACK/SS2 and PGOOD2 pins become defunct and can be left open. Note that the RUN1, RUN2, DTR1, DTR2, VRNG1 and VRNG2 pins still function for the two channels individually, therefore should be shorted * Tie the VOUTSENSE1+ pin to the VOUTSENSE1+ pin of the first chip * Tie the VOUTSENSE1- pin to the VOUTSENSE1- pin of the first chip * Tie the TRACK/SS1 pin to the TRACK/SS1 pin of the first chip 3838fb For more information www.linear.com/LTC3838 17 LTC3838 Applications Information Once the required output voltage and operating frequency have been determined, external component selection is driven by load requirement, and begins with the selection of inductors and current sense method (either sense resistors RSENSE or inductor DCR sensing). Next, power MOSFETs are selected. Finally, input and output capacitors are selected. Output Voltage Programming As shown in Figure 1, external resistor dividers are used from the regulated outputs to their respective ground references to program the output voltages. On Channel 1, the resistive divider is tapped by the VOUTSENSE1+ pin, and the ground reference is remotely sensed by the VOUTSENSE1- pin, this voltage is sensed differentially. On Channel 2, the resistive divider is tapped by the VFB2 pin, with respect to signal ground at the SGND pin. By regulating the tapped (differential) feedback voltages to the internal reference 0.6V, the resulting output voltages are: VOUT1 - VOUTSENSE1- = 0.6V * (1 + RFB2/RFB1) and VOUT2 = 0.6V * (1 + RFB2/RFB1) For example, if VOUT1 is programmed to 5V and the output ground reference is sitting at -0.5V with respect to SGND, then the absolute value of the output will be 4.5V with respect to SGND. The minimum (differential) output voltages are limited to the internal reference 0.6V, and the maximum are 5.5V. The VOUTSENSE1+ pin is a high impedance pin with no input bias current other than leakage in the nA range. The VOUTSENSE1- pin has about 30A of current flowing out of the pin. The VFB2 pin is quasi-high impedance pin with minimum bias current out of the pin. Differential output sensing allows for more accurate output regulation in high power distributed systems having large line losses. Figure 2 illustrates the potential variations in the power and ground lines due to parasitic elements. The variations may be exacerbated in multi-application systems with shared ground planes. Without differential output sensing, these variations directly reflect as an error in the regulated output voltage. The LTC3838 Channel 1's differential output sensing can correct for up to 500mV of variation in the output's power and ground lines. The LTC3838 Channel 1's differential output sensing scheme is distinct from conventional schemes where the regulated output and its ground reference are directly sensed with a difference amplifier whose output is then divided down with an external resistor divider and fed into the error amplifier input. This conventional scheme is limited by the common mode input range of the difference amplifier and typically limits differential sensing to the lower range of output voltages. The LTC3838's Channel 1 allows for seamless differential output sensing by sensing the resistively divided feedback voltage differentially. This allows for differential sensing in the full output range from 0.6V to 5.5V. The difference amplifier (DIFFAMP) has a bandwidth of 8MHz, high VOUT LTC3838 RFB2 COUT VOUTSENSE1+/VFB2 RFB1 VOUTSENSE1-/SGND 3838 F01 Figure 1. Setting Output Voltage 3838fb 18 For more information www.linear.com/LTC3838 LTC3838 Applications Information CIN MT LTC3838 VOUTSENSE1+ VOUTSENSE1- RFB2 + - VIN POWER TRACE PARASITICS L VDROP(PWR) MB RFB1 COUT1 ILOAD COUT2 I LOAD GROUND TRACE PARASITICS VDROP(GND) OTHER CURRENTS FLOWING IN SHARED GROUND PLANE 3838 F02 Figure 2. Differential Output Sensing Used to Correct Line Loss Variations in a High Power Distributed System with a Shared Ground Plane enough so that it will not affect main loop compensation and transient behavior. To avoid noise coupling into the feedback voltages (VOUTSENSE1+ or VFB2), the resistor dividers should be placed close to the VOUTSENSE1+ and VOUTSENSE1-, or VFB2 and SGND pins. Remote output and ground traces should be routed together as a differential pair to the remote output. For best accuracy, these traces to the remote output and ground should be connected as close as possible to the desired regulation point. Switching Frequency Programming The choice of operating frequency is a trade-off between efficiency and component size. Lowering the operating frequency improves efficiency by reducing MOSFET switching losses but requires larger inductance and/or capacitance to maintain low output ripple voltage. Conversely, raising the operating frequency degrades efficiency but reduces component size. The switching frequency of the LTC3838 can be programmed from 200kHz to 2MHz by connecting a resistor from the RT pin to signal ground. The value of this resistor can be chosen according to the following formula: R T [k ] = 41550 - 2.2 f [kHz ] The overall controller system, including the clock PLL and switching channels, has a synchronization range of no less than 30% around this programmed frequency. Therefore, during external clock synchronization be sure that the external clock frequency is within this 30% range of the RT programmed frequency. It is advisable that the RT programmed frequency be equal the external clock for maximum synchronization margin. Refer to the "Phase and Frequency Synchronization" section for more details. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. A higher frequency generally results in lower efficiency because of MOSFET gate charge losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. 3838fb For more information www.linear.com/LTC3838 19 LTC3838 Applications Information The inductor value has a direct effect on ripple current. The inductor ripple current IL decreases with higher inductance or frequency and increases with higher VIN: V V IL = OUT 1- OUT f *L VIN Accepting larger values of IL allows the use of low inductances, but results in higher output voltage ripple, higher ESR losses in the output capacitor, and greater core losses. A reasonable starting point for setting ripple current is IL = 0.4 * IMAX. The maximum IL occurs at the maximum input voltage. To guarantee that ripple current does not exceed a specified maximum, the inductance should be chosen according to: V VOUT OUT 1- L= f * IL(MAX) VIN(MAX) Inductor Core Selection Once the value for L is known, the type of inductor must be selected. The two basic types are iron powder and ferrite. The iron powder types have a soft saturation curve which means they do not saturate hard like ferrites do. However, iron powder type inductors have higher core losses. Ferrite designs have very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. Ferrite core material saturates hard, which means that inductance collapses abruptly when the peak design current is exceeded. This results an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! A variety of inductors designed for high current, low voltage applications are available from manufacturers such as Sumida, Panasonic, Coiltronics, Coilcraft, Toko, Vishay, Pulse and Wurth. Current Sense Pins Inductor current is sensed through voltage between SENSE+ and SENSE- pins, the inputs of the internal current comparators. The input voltage range of the SENSE pins is -0.5V to 5.5V. Care must be taken not to float these pins during normal operation. The SENSE+ pins are quasi-high impedance inputs. There is no bias current into a SENSE+ pin when its corresponding channel's SENSE- pin ramps up from below 1.1V and stays below 1.4V. But there is a small (~1A) current flowing into a SENSE+ pin when its corresponding SENSE- pin ramps down from 1.4V and stays above 1.1V. Such currents also exist on SENSE- pins. But in addition, each SENSE- pin has an internal 500k resistor to SGND. The resulted current (VOUT/500k) will dominate the total current flowing into the SENSE- pins. SENSE+ and SENSE- pin currents have to be taken into account when designing either RSENSE or DCR inductor current sensing. Current Limit Programming The current sense comparators' maximum trip voltage between SENSE+ and SENSE- (or "sense voltage"), when ITH is clamped at its maximum 2.4V, is set by the voltage applied to the VRNG pin and is given by: VSENSE(MAX) = 0.05VRNG The valley current mode control loop does not allow the inductor current valley to exceed 0.05VRNG. In practice, one should allow sufficient margin, to account for tolerance of the parts and external component values. Note that ITH is close to 2.4V when in current limit. An external resistive divider from INTVCC can be used to set the voltage on a VRNG pin between 0.6V and 2V, resulting in a maximum sense voltage between 30mV and 100mV. Such wide voltage range allows for variety of applications. The VRNG pin can also be tied to either SGND or INTVCC to force internal defaults. When VRNG is tied to SGND, the device has an equivalent VRNG of 0.6V. When the VRNG pin is tied to INTVCC, the device has an equivalent VRNG of 1V. 3838fb 20 For more information www.linear.com/LTC3838 LTC3838 Applications Information RSENSE Inductor Current Sensing The LTC3838 can be configured to sense the inductor currents through either low value series current sensing resistors (RSENSE) or inductor DC resistance (DCR). The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption and accuracy. DCR sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. A typical RSENSE inductor current sensing scheme is shown in Figure 3a. The filter components (RF , CF) need to be placed close to the IC. The positive and negative sense traces need to be routed as a differential pair close together and Kelvin (4-wire) connected underneath the sense resistor, as shown in Figure 3b. Sensing current elsewhere can effectively add parasitic inductance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. RSENSE is chosen based on the required maximum output current. Given the maximum current, IOUT(MAX), maximum sense voltage, VSENSE(MAX), set by VRNG, and maximum inductor ripple current IL(MAX), the value of RSENSE can be chosen as: RSENSE = VSENSE(MAX) IL(MAX) IOUT(MAX) - 2 Conversely, given RSENSE and IOUT(MAX), VSENSE(MAX) and thus VRNG voltage can be determined from the above equation. To ensure the maximum output current, sufficient margin should be built in the calculations to account for variations of LTC3838 under different operating conditions and tolerances of external components. Because of possible PCB noise in the current sensing loop, the current sensing voltage ripple VSENSE = IL * RSENSE also needs to be checked in the design to get a RSENSE RESISTOR AND PARASITIC INDUCTANCE R LTC3838 CF SENSE- VOUT CF * 2RF ESL/RS POLE-ZERO CANCELLATION RF SENSE+ ESL RF 3838 F03a FILTER COMPONENTS PLACED NEAR SENSE PINS Figure 3a. RSENSE Current Sensing TO SENSE FILTER, NEXT TO THE CONTROLLER COUT RSENSE 3838 F03b Figure 3b. Sense Lines Placement with Sense Resistor good signal-to-noise ratio. In general, for a reasonably good PCB layout, 10mV of VSENSE is recommended as a conservative number to start with, either for RSENSE or Inductor DCR sensing applications. For today's highest current density solutions the value of the sense resistor can be less than 1m and the peak sense voltage can be as low as 20mV. In addition, inductor ripple currents greater than 50% with operation up to 2MHz are becoming more common. Under these conditions, the voltage drop across the sense resistor's parasitic inductance becomes more relevant. A small RC filter placed near the IC has been traditionally used to reduce the effects of capacitive and inductive noise coupled in the sense traces on the PCB. A typical filter consists of two series 10 resistors connected to a parallel 1000pF capacitor, resulting in a time constant of 20ns. This same RC filter, with minor modifications, can be used to extract the resistive component of the current sense signal in the presence of parasitic inductance. 3838fb For more information www.linear.com/LTC3838 21 LTC3838 Applications Information For example, Figure 4a illustrates the voltage waveform across a 2m sense resistor with a 2010 footprint for a 1.2V/15A converter operating at 100% load. The waveform is the superposition of a purely resistive component and a purely inductive component. It was measured using two scope probes and waveform math to obtain a differential measurement. Based on additional measurements of the inductor ripple current and the on-time and off-time of the top switch, the value of the parasitic inductance was determined to be 0.5nH using the equation: ESL = VESL(STEP) tON * tOFF * IL tON + tOFF where VESL(STEP) is the voltage step caused by the ESL and shown in Figure 4a, and tON and tOFF are top MOSFET on-time and off-time respectively. If the RC time constant VSENSE 20mV/DIV VESL(STEP) 500ns/DIV 3838 F04a Figure 4a. Voltage Waveform Measured Directly Across the Sense Resistor VSENSE 20mV/DIV is chosen to be close to the parasitic inductance divided by the sense resistor (L/R), the resulting waveform looks resistive again, as shown in Figure 4b. For applications using low VSENSE(MAX), check the sense resistor manufacturer's data sheet for information about parasitic inductance. In the absence of data, measure the voltage drop directly across the sense resistor to extract the magnitude of the ESL step and use the equation above to determine the ESL. However, do not over filter. Keep the RC time constant less than or equal to the inductor time constant to maintain a high enough ripple voltage on VRSENSE. Note that the SENSE1- and SENSE2- pins are also used for sensing the output voltage for the adjustment of top gate on time, tON. For this purpose, there is an additional internal 500k resistor from each SENSE- pin to SGND, therefore there is an impedance mismatch with their corresponding SENSE+ pins. The voltage drop across the RF causes an offset in sense voltage. For example, with RF = 100, at VOUT = VSENSE- = 5V, the sense-voltage offset VSENSE(OFFSET) = VSENSE- * RF/500k = 1mV. Such small offset may seem harmless for current limit, but could be significant for current reversal detection (IREV), causing excess negative inductor current at discontinuous mode. Also, at VSENSE(MAX) = 30mV, a mere 1mV offset will cause a significant shift of zero-current ITH voltage by (2.4V - 0.8V) * 1mV/30mV = 53mV. Too much shift may not allow the output voltage to return to its regulated value after the output is shorted due to ITH foldback. Therefore, when a larger filter resistor RF value is used, it is recommended to use an external 500k resistor from each SENSE+ pin to SGND, to balance the internal 500k resistor at its corresponding SENSE- pin. The previous discussion generally applies to high density/ high current applications where IOUT(MAX) > 10A and low inductor values are used. For applications where IOUT(MAX) 500ns/DIV 3838 F04b Figure 4b. Voltage Waveform Measured After the Sense Resistor Filter. CF = 1000pF, RF = 100 3838fb 22 For more information www.linear.com/LTC3838 LTC3838 Applications Information < 10A, set RF to 10 and CF to 1000pF. This will provide a good starting point. The filter components need to be placed close to the IC. The positive and negative sense traces need to be routed as a differential pair and Kelvin (4-wire) connected to the sense resistor. DCR Inductor Current Sensing For applications requiring higher efficiency at high load currents, the LTC3838 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 5. The DCR of the inductor represents the small amount of DC winding resistance, which can be less than 1m for today's low value, high current inductors. In a high current application requiring such an inductor, conduction loss through a sense resistor would cost several points of efficiency compared to DCR sensing. The inductor DCR is sensed by connecting an RC filter across the inductor. This filter typically consists of one or two resistors (R1 and R2) and one capacitor (C1) as shown in Figure 5. If the external (R1||R2) * C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the voltage drop across the inductor DCR multiplied by R2/ (R1 + R2). Therefore, R2 may be used to scale the voltage across the sense terminals when the DCR is greater than INDUCTOR L DCR VOUT COUT L/DCR = (R1||R2) C1 LTC3838 the target sense resistance. With the ability to program current limit through the VRNG pin, R2 may be optional. C1 is usually selected in the range of 0.01F to 0.47F. This forces R1||R2 to around 2k to 4k, reducing error that might have been caused by the SENSE pins' input bias currents. Resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. Capacitor C1 should be placed close to the IC pins. The first step in designing DCR current sensing is to determine the DCR of the inductor. Where provided, use the manufacturer's maximum value, usually given at 25C. Increase this value to account for the temperature coefficient of resistance, which is approximately 0.4%/C. A conservative value for inductor temperature TL is 100C. The DCR of the inductor can also be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature; consult the manufacturers' data sheets for detailed information. From the DCR value, VSENSE(MAX) is easily calculated as: VSENSE(MAX) = DCRMAX(25C) ( ) * 1+ 0.4% TL(MAX) - 25C I * IOUT(MAX) - L 2 If VSENSE(MAX) is within the maximum sense voltage (30mV to 100mV) of the LTC3838 as programmed by the VRNG pin, then the RC filter only needs R1. If VSENSE(MAX) is higher, then R2 may be used to scale down the maximum sense voltage so that it falls within range. R1 SENSE+ C1 - SENSE R2 (OPT) 3838 F05 C1 NEAR SENSE PINS Figure 5. DCR Current Sensing 3838fb For more information www.linear.com/LTC3838 23 LTC3838 Applications Information The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: PLOSS (V (R1) = IN(MAX) - VOUT R1 )* V CMILLER OUT Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or RSENSE sensing. Light load power loss can be modestly higher with a DCR network than with a sense resistor due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. To maintain a good signal-to-noise ratio for the current sense signal, start with a VSENSE of 10mV. For a DCR sensing application, the actual ripple voltage will be determined by: VSENSE = horizontal axis while the curve is approximately flat (or the parameter QGD if specified on a manufacturer's data sheet), divided by the specified VDS test voltage: VIN - VOUT VOUT * R1* C1 VIN * f QGD VDS(TEST) When the IC is operating in continuous mode, the duty cycles for the top and bottom MOSFETs are given by: VOUT VIN V DBOT = 1- OUT VIN DTOP = The MOSFET power dissipations at maximum output current are given by: PTOP = DTOP *IOUT(MAX)2 *RDS(ON)(MAX) (1+ ) + VIN 2 R TG(UP) R TG(DOWN) IOUT(MAX) * + *CMILLER *f 2 VMILLER VDRVCC - VMILLER PBOT = DBOT * IOUT(MAX)2 * RDS(ON)(MAX) * (1 + ) Power MOSFET Selection Two external N-channel power MOSFETs must be selected for each channel of the LTC3838 controller: one for the top (main) switch and one for the bottom (synchronous) switch. The gate drive levels are set by the DRVCC voltage. This voltage is typically 5.3V. Pay close attention to the BVDSS specification for the MOSFETs as well; most of the logic-level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the onresistance, RDS(ON), Miller capacitance, CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturers' data sheet. CMILLER is equal to the increase in gate charge along the where is the temperature dependency of RDS(ON), RTG(UP) is the TG pull-up resistance, and RTG(DOWN) is the TG pulldown resistance. VMILLER is the Miller effect VGS voltage and is taken graphically from the MOSFET 's data sheet. Both MOSFETs have I2R losses while the topside N-channel equation includes an additional term for transition losses, which are highest at high input voltages. For VIN < 20V, the high current efficiency generally improves with larger MOSFETs, while for VIN > 20V, the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the top switch duty factor is low or during short-circuit when the synchronous switch is on close to 100% of the period. 3838fb 24 For more information www.linear.com/LTC3838 LTC3838 Applications Information The term (1 + ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs temperature curve in the power MOSFET data sheet. For low voltage MOSFETs, 0.5% per degree (C) can be used to estimate as an approximation of percentage change of RDS(ON): = 0.005/C * (TJ - TA) where TJ is estimated junction temperature of the MOSFET and TA is ambient temperature. CIN Selection In continuous mode, the source current of the top Nchannel MOSFET is a square wave of duty cycle VOUT/ VIN. To prevent large voltage transients, a low ESR input capacitor sized for the maximum RMS current must be used. The worst-case RMS current occurs by assuming a singlephase application. The maximum RMS capacitor current is given by: IRMS IOUT(MAX) * VOUT * VIN VIN -1 VOUT This formula has a maximum at VIN = 2VOUT , where IRMS = IOUT(MAX)/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours of life. This makes it advisable to further derate the capacitor or to choose a capacitor rated at a higher temperature than required. Several capacitors may also be paralleled to meet size or height requirements in the design. Due to the high operating frequency of the LTC3838, additional ceramic capacitors should also be used in parallel for CIN close to the IC and power switches to bypass the high frequency switching noises. Typically multiple X5R or X7R ceramic capacitors are put in parallel with either conductive-polymer or aluminum-electrolytic types of bulk capacitors. Because of its low ESR, the ceramic capacitors will take most of the RMS ripple current. Vendors do not consistently specify the ripple current rating for ceramics, but ceramics could also fail due to excessive ripple current. Always consult the manufacturer if there is any question. Figure 6 represents a simplified circuit model for calculating the ripple currents in each of these capacitors. The input inductance (LIN) between the input source and the input of the converter will affect the ripple current through the capacitors. A lower input inductance will result in less ripple current through the input capacitors since more ripple current will now be flowing out of the input source. For simulations with this model, look at the ripple current during steady-state for the case where one phase is fully loaded and the other was not loaded. This will in general be the worst case for ripple current since the ripple current from one phase will not be cancelled by ripple current from the other phase. Note that the bulk capacitor also has to be chosen for RMS rating with ample margin beyond its RMS current per simulation with the circuit model provided. For a lower VIN range, a conductive-polymer type (such as Sanyo OSCON) can be used for its higher ripple current rating and lower ESR. For a wide VIN range that also require higher voltage rating, aluminum-electrolytic capacitors are LIN 1H + - VIN + ESR(BULK) ESR(CERAMIC) ESL(BULK) ESL(CERAMIC) CIN(BULK) IPULSE(PHASE1) IPULSE(PHASE2) CIN(CERAMIC) 3838 F06 Figure 6. Circuit Model for Input Capacitor Ripple Current Simulation 3838fb For more information www.linear.com/LTC3838 25 LTC3838 Applications Information more attractive since it can provide a larger capacitance for more damping. An aluminum-electrolytic capacitor with a ripple current rating that is high enough to handle all of the ripple current by itself will be very large. But when in parallel with ceramics, an aluminum-electrolytic capacitor will take a much smaller portion of the RMS ripple current due to its high ESR. However, it is crucial that the ripple current through the aluminum-electrolytic capacitor should not exceed its rating since this will produce significant heat, which will cause the electrolyte inside the capacitor to dry over time and its capacitance to go down and ESR to go up. The benefit of PolyPhase operation is reduced RMS currents and therefore less power loss on the input capacitors. Also, the input protection fuse resistance, battery resistance, and PC board trace resistance losses are also reduced due to the reduced peak currents in a PolyPhase system. The details of a close form equation can be found in Application Note 77 "High Efficiency, High Density, PolyPhase Converters for High Current Applications". Figure 7 shows the input capacitor RMS ripple currents normalized against the DC output currents with respect to the duty cycle. This graph can be used to estimate the maximum RMS capacitor current for a multiple-phase 0.5 DC LOAD CURRENT RMS INPUT RIPPLE CURRNET 0.6 0.3 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 DUTY FACTOR (VO/VIN) Figure 7 shows that the use of more phases will reduce the ripple current through the input capacitors due to ripple current cancellation. However, since LTC3838 is only truly phase-interleaved at steady state, transient RMS currents could be higher than the curves for the designated number of phase. Therefore, it is advisable to choose capacitors by taking account the specific load situations of the applications. It is always the safest to choose input capacitors' RMS current rating closer to the worst case of a single-phase application discussed above, calculated by assuming the loss that would have resulted if controller channels switched on at the same time. However, it is generally not needed to size the input capacitor for such worst-case conditions where on-times of the phases coincide all the time. During a load step event, the overlap of on-time will only occur for a small percentage of time, especially when duty cycles are low. A transient event where the switch nodes align for several cycles at a time should not damage the capacitor. In most applications, sizing the input capacitors for 100% steady-state load should be adequate. For example, a microprocessor load may cause frequent overlap of the on-times, which makes the ripple current higher, but the load current may rarely be at 100% of IOUT(MAX). Using the worst-case load current should already have margin built in for transient conditions. The VIN sources of the top MOSFETs should be placed close to each other and share common CIN(s). Separating the sources and CIN may produce undesirable voltage and current resonances at VIN. 1-PHASE 2-PHASE 3-PHASE 4-PHASE 6-PHASE 0.4 application, assuming the channels are identical and their phases are fully interleaved. 0.8 0.9 3838 F07 Figure 7. Normalized RMS Input Ripple Current A small (0.1F to 1F) bypass capacitor between the IC's VIN pin and ground, placed close to the IC, is suggested. A 2.2 to 10 resistor placed between CIN and the VIN pin is also recommended as it provides further isolation from switching noise of the two channels. 3838fb 26 For more information www.linear.com/LTC3838 LTC3838 Applications Information COUT Selection The selection of output capacitance COUT is primarily determined by the effective series resistance, ESR, to minimize voltage ripple. The output voltage ripple VOUT , in continuous mode is determined by: 1 VOUT IL RESR + 8 * f * COUT where f is operating frequency, and IL is ripple current in the inductor. The output ripple is highest at maximum input voltage since IL increases with input voltage. Typically, once the ESR requirement for COUT has been met, the RMS current rating generally far exceeds that required from ripple current. In multiphase single-output applications, it is advisable to consider ripple requirements at specific load conditions. At steady state, the LTC3838's individual phases are interleaved, and their ripples cancel each other at the output, so ripple on COUT is reduced. During transient, when the phases are not fully interleaved, the ripple cancellation may not be as effective. While the worst-case IL is the sum of the ILs of individual phases aligned during a fast transient, such ripple tends to counteract the effect of load transient itself and lasts for only a short time. For example, during sudden load current increase, the phases align to ramp up the total inductor current to quickly pull the VOUT up from the droop. The choice of using smaller output capacitance increases the ripple voltage due to the discharging term but can be compensated for by using capacitors of very low ESR to maintain the ripple voltage. Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Special polymer capacitors offer very low ESR but have lower capacitance density than other types. Tantalum capacitors have the highest capacitance density but it is important to only use types that have been surge tested for use in switching power supplies. Aluminum electrolytic capacitors have significantly higher ESR, but can be used in cost-sensitive applications provided that consideration is given to ripple current ratings and long-term reliability. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient and audible piezoelectric effects. The high Q of ceramic capacitors with trace inductance can also lead to significant ringing. When used as input capacitors, care must be taken to ensure that ringing from inrush currents and switching does not pose an overvoltage hazard to the power switches and controller. For high switching frequencies, reducing output ripple and better EMI filtering may require small value capacitors that have low ESL (and correspondingly higher self-resonant frequencies) to be placed in parallel with larger value capacitors that have higher ESL. This will ensure good noise and EMI filtering in the entire frequency spectrum of interest. Even though ceramic capacitors generally have good high frequency performance, small ceramic capacitors may still have to be parallel connected with large ones to optimize performance. High performance through-hole capacitors may also be used, but an additional ceramic capacitor in parallel is recommended to reduce the effect of their lead inductance. Remember also to place high frequency decoupling capacitors as close as possible to the power pins of the load. Top MOSFET Driver Supply (CB, DB) An external bootstrap capacitor, CB, connected to the BOOST pin supplies the gate drive voltage for the topside MOSFET. This capacitor is charged through diode DB from DRVCC when the switch node is low. When the top MOSFET turns on, the switch node rises to VIN and the BOOST pin rises to approximately VIN + INTVCC. The boost capacitor needs to store approximately 100 times the gate charge required by the top MOSFET. In most applications a 0.1F to 0.47F, X5R or X7R dielectric capacitor is adequate. It is recommended that the BOOST capacitor be no larger than 10% of the DRVCC capacitor, CDRVCC, to ensure that the CDRVCC can supply the upper MOSFET gate charge 3838fb For more information www.linear.com/LTC3838 27 LTC3838 Applications Information and BOOST capacitor under all operating conditions. Variable frequency in response to load steps offers superior transient performance but requires higher instantaneous gate drive. Gate charge demands are greatest in high frequency low duty factor applications under high load steps and at start-up. DRVCC Regulator and EXTVCC Power The LTC3838 features a PMOS low dropout (LDO) linear regulator that supplies power to DRVCC from the VIN supply. The LDO regulates its output at the DRVCC1 pin to 5.3V. The LDO can supply a maximum current of 100mA and must be bypassed to ground with a minimum of 4.7F ceramic capacitor. Good bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to minimize interaction between the channels. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3838 to be exceeded, especially if the LDO is active and provides DRVCC. Power dissipation for the IC in this case is highest and is approximately equal to VIN * IDRVCC. The gate charge current is dependent on operating frequency as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equation given in Note 2 of the Electrical Characteristics. For example, when using the LDO, LTC3838's DRVCC current is limited to less than 52mA from a 38V supply at TA = 70C in the FE package: TJ = 70C + (52mA)(38V)(28C/W) = 125C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in continuous conduction mode at maximum VIN. When the voltage applied to the EXTVCC pin rises above the switchover voltage (typically 4.6V), the VIN LDO is turned off and the EXTVCC is connected to DRVCC2 pin with an internal switch. This switch remains on as long as the voltage applied to EXTVCC remains above the hysteresis (around 200mV) below the switchover voltage. Using EXTVCC allows the MOSFET driver and control power to be derived from the LTC3838's switching regulator output VOUT during normal operation and from the LDO when the output is out of regulation (e.g., start up, short circuit). If more current is required through the EXTVCC than is specified, an external Schottky diode can be added between the EXTVCC and DRVCC pins. Do not apply more than 6V to the EXTVCC pin and make sure that EXTVCC is less than VIN. Significant efficiency and thermal gains can be realized by powering DRVCC from the switching converter output, since the VIN current resulting from the driver and control currents will be scaled by a factor of (Duty Cycle)/(Switcher Efficiency). Tying the EXTVCC pin to a 5V supply reduces the junction temperature in the previous example from 125C to: TJ = 70C + (52mA)(5V)(28C/W) = 77C However, for 3.3V and other low voltage outputs, additional circuitry is required to derive DRVCC power from the converter output. The following list summarizes the four possible connections for EXTVCC: 1. EXTVCC left open (or grounded). This will cause INTVCC to be powered from the internal 5.3V LDO resulting in an efficiency penalty of up to 10% at high input voltages. 2. EXTVCC connected directly to switching converter output VOUT is higher than the switchover voltage's higher limit (4.8V). This provides the highest efficiency. 3. EXTVCC connected to an external supply. If a 4.8V or greater external supply is available, it may be used to power EXTVCC providing that the external supply is sufficient for MOSFET gate drive requirements. 4. EXTVCC connected to an output-derived boost network. For 3.3V and other low voltage converters, efficiency gains can still be realized by connecting EXTVCC to an output-derived voltage that has been boosted to greater than 4.8V. 3838fb 28 For more information www.linear.com/LTC3838 LTC3838 Applications Information For applications where the main input power never exceeds 5.3V, tie the DRVCC1 and DRVCC2 pins to the VIN input through a small resistor, (such as 1 to 2) as shown in Figure 8 to minimize the voltage drop caused by the gate charge current. This will override the LDO and will prevent DRVCC from dropping too low due to the dropout voltage. Make sure the DRVCC voltage exceeds the RDS(ON) test voltage for the external MOSFET which is typically at 4.5V for logic-level devices. LTC3838 DRVCC2 DRVCC1 RDRVCC VIN CDRVCC CIN 3838 F08 Figure 8. Setup for VIN 5.3V Input Undervoltage Lockout (UVLO) The LTC3838 has two functions that help protect the controller in case of input undervoltage conditions. An internal UVLO comparator constantly monitors the INTVCC and DRVCC voltages to ensure that adequate voltages are present. The comparator enables internal UVLO signal, which locks out the switching action of both channels, until the INTVCC and DRVCC1,2 pins are all above their respective UVLO thresholds. The rising threshold (to release UVLO) of the INTVCC is typically 4.2V, with 0.5V falling hysteresis (to re-enable UVLO). The UVLO thresholds for DRVCC1,2 are lower than that of INTVCC but higher than typical threshold voltages of power MOSFETs, to prevent them from turning on without sufficient gate drive voltages. Generally for VIN > 6V, a UVLO can be set through monitoring the VIN supply by using external voltage dividers at the RUN pins from VIN to SGND. To design the voltage divider, note that both RUN pins have two levels of threshold voltages. The precision gate-drive-enable threshold voltage of 1.2V can be used to set a VIN to turn on a channel's switching. If resistor dividers are used on both RUN pins, when VIN is low enough and both RUN pins are pulled below the ~0.8V threshold, the part will shut down all bias of INTVCC and DRVCC and be put in micropower shutdown mode. The RUN pins' bias currents depend on the RUN voltages. The bias current changes should be taken into account when designing the external voltage divider UVLO circuit. An internal proportional-to-absolute-temperature (PTAT) pull-up current source (~1.2A at 25C) is constantly connected to this pin. When a RUN pin rises above 1.2V, the corresponding channel's TG and BG drives are turned on and an additional 5A temperature-independent pull-up current is connected internally to the RUN pin. Pulling the RUN pin to fall below 1.2V by more than an 80mV hysteresis turns off TG and BG of the corresponding channel, and the additional 5A pull-up current is disconnected. As voltage on a RUN pin increases, typically beyond 3V, its bias current will start to reverse direction and flow into the RUN pin. Keep in mind that neither of the RUN pins can sink more than 50A; Even if a RUN pin may slightly exceed 6V when sinking 50A, a RUN pin should never be forced to higher than 6V by a low impedance voltage source to prevent faulty conditions. Soft-Start and Tracking The LTC3838 has the ability to either soft-start by itself with a capacitor or track the output of another channel or an external supply. Note that the soft-start and tracking features are achieved not by limiting the maximum output current of the controller, but by controlling the output ramp voltage according to the ramp rate on the TRACK/SS pin. 3838fb For more information www.linear.com/LTC3838 29 LTC3838 Applications Information When a channel is configured to soft-start by itself, a capacitor should be connected to its TRACK/SS pin. TRACK/ SS is pulled low until the RUN pin voltage exceeds 1.2V and UVLO is released, at which point an internal current of 1A charges the soft-start capacitor, CSS, connected to the TRACK/SS pin. Current-limit foldback is disabled during this phase to ensure smooth soft-start or tracking. The soft-start or tracking range is defined to be the voltage range from 0V to 0.6V on the TRACK/SS pin. The total soft-start time can be calculated as: t SS (SEC) = 0.6(V)* CSS (F) 1(A) When one particular channel is configured to track an external supply, a voltage divider can be used from the external supply to the TRACK/SS pin to scale the ramp rate appropriately. Two common implementations are coincidental tracking and ratiometric tracking. For coincident tracking, make the divider ratio from the external supply the same as the divider ratio for the differential feedback voltage. Ratiometric tracking could be achieved by using a different ratio than the differential feedback. Note that the 1A soft-start capacitor charging current is still flowing, producing a small offset error. To minimize this error, select the tracking resistive divider values to be small enough to make this offset error negligible. The LTC3838 allows the user to program how its two channels' outputs track each other ramping up or down. In the following discussions, VOUT1 refers to the LTC3838's output 1 as a master channel and VOUT2 refers to the LTC3838's output 2 as a slave channel. In practice though, either channel can be used as the master. By selecting different resistors, the LTC3838 can achieve different modes of tracking including the two in Figure 9. To implement the coincident tracking, connect an additional resistive divider to VOUT1 and connect its midpoint to the TRACK/SS pin of the slave channel. The ratio of this divider should be the same as that of the slave channel's feedback divider shown in Figure 9b. In this tracking mode, VOUT2 VOUT1 OUTPUT VOLTAGE OUTPUT VOLTAGE VOUT1 VOUT2 TIME TIME Coincident Tracking 3838 F09a Ratiometric Tracking Figure 9a. Two Different Modes of Output Tracking VOUT1 TO TRACK/SS2 PIN RFB2(2) RFB1(2) RFB2(1) TO VOUTSENSE1+ PIN RFB1(1) TO VOUTSENSE1- PIN TO VFB2 PIN VOUT2 RFB2(2) RFB1(2) VOUT1 TO TRACK/SS2 PIN Coincident Tracking Setup RFB2(1) RFB1(1) TO VOUTSENSE1+ PIN TO VFB2 PIN TO VOUTSENSE1- PIN VOUT2 RFB2(2) RFB1(2) 3838 F09b Ratiometric Tracking Setup Figure 9b. Setup for Coincident and Ratiometric Tracking 3838fb 30 For more information www.linear.com/LTC3838 LTC3838 Applications Information VOUT1 must be set higher than VOUT2. To implement the ratiometric tracking, the master channel's feedback divider can be also used to provide TRACK/SS voltage for the slave channel, since the additional divider, if used, should be of the same ratio as the master channel's feedback divider. So which mode should be programmed? While either mode satisfies most practical applications, some tradeoffs exist. The ratiometric mode saves a pair of resistors, but the coincident mode offers better output regulation. When the master channel's output experiences dynamic excursion (under load transient, for example), the slave channel output will be affected as well. For better output regulation, use the coincident tracking mode instead of ratiometric. Phase and Frequency Synchronization For applications that require better control of EMI and switching noise or have special synchronization needs, the LTC3838 can synchronize the turn-on of the top MOSFET to an external clock signal applied to the MODE/PLLIN pin. The applied clock signal needs to be within 30% of the RT programmed frequency to ensure proper frequency and phase lock. The clock signal levels should generally comply to VPLLIN(H) > 2V and VPLLIN(L) < 0.5V. The MODE/ PLLIN pin has an internal 600k pull-down resistor to ensure discontinuous current mode operation if the pin is left open. The LTC3838 uses the voltages on VIN and VOUT as well as RT to adjust the top gate on-time in order to maintain phase and frequency lock for wide ranges of VIN, VOUT and RT-programmed switching frequency f: tON VOUT VIN * f As the on-time is a function of the switching regulator's output voltage, this output is measured by the SENSE- pin to set the required on-time. The SENSE- pin is tied to the regulator's local output point to the IC for most applications, as the remotely regulated output point could be significantly different from the local output point due to line losses, and local output versus local ground is typically the VOUT required for the calculation of tON. However, there could be circumstances where this VOUT programmed on-time differs significantly different from the on-time required in order to maintain frequency and phase lock. For example, lower efficiencies in the switching regulator can cause the required on-time to be substantially higher than the internally set on-time (see Efficiency Considerations). If a regulated VOUT is relatively low, proportionally there could be significant error caused by the difference between the local ground and remote ground, due to other currents flowing through the shared ground plane. If necessary, the RT resistor value, voltage on the VIN pin, or even the common mode voltage of the SENSE pins may be programmed externally to correct for such systematic errors. The goal is to set the on-time programmed by VIN, VOUT and RT close to the stready-state on-time so that the system will have sufficient range to correct for component and operating condition variations, or to synchronize to the external clock. Note that there is an internal 500k resistor on each SENSE- pin to SGND, but not on the SENSE+ pin. During dynamic transient conditions either in the line voltage or load current (e.g., load step or release), the top switch will turn on more or less frequently in response to achieve faster transient response. This is the benefit of the LTC3838's controlled on-time, valley current mode architecture. However, this process may understandably lose phase and even frequency lock momentarily. For relatively slow changes, phase and frequency lock can still be maintained. For large load current steps with fast slew rates, phase lock will be lost until the system returns back to a steady-state condition (see Figure 10). It may take up to several hundred microseconds to fully resume the phase lock, but the frequency lock generally recovers quickly, long before phase lock does. For light load conditions, the phase and frequency synchronization depends on the MODE/PLLIN pin setting. If the external clock is applied, synchronization will be active and switching in continuous mode. If MODE/PLLIN is tied to INTVCC, it will operate in forced continuous mode at the RT-programmed frequency. If the MODE/PLLIN pin is tied to SGND, the LTC3838 will operate in discontinuous 3838fb For more information www.linear.com/LTC3838 31 LTC3838 Applications Information ILOAD CLOCK INPUT PHASE AND FREQUENCY LOCKED PHASE AND FREQUENCY LOCK LOST DUE TO FAST LOAD STEP FREQUENCY RESTORED QUICKLY PHASE LOCK RESUMED PHASE AND FREQUENCY LOCK LOST DUE TO FAST LOAD STEP FREQUENCY RESTORED QUICKLY SW VOUT 3838 F10 Figure 10. Phase and Frequency Locking Behavior During Transient Conditions mode at light load and switch into continuous conduction at the RT programmed frequency as load increases. The TG on-time during discontinuous conduction is intentionally slightly extended (approximately 1.2 times the continuous conduction on-time as calculated from VIN, VOUT and f) to create hysteresis at the load-current boundary of continuous/discontinuous conduction. If an application requires very low (approaching minimum) on-time, the system may not be able to maintain its full frequency synchronization range. Getting closer to minimum on-time, it may even lose phase/frequency lock at no load or light load conditions, under which the SW on-time is effectively longer than TG on-time due to TG/BG dead times. This is discussed further under Minimum On-Time, Minimum Off-Time and Dropout Operation. Minimum On-Time, Minimum Off-Time and Dropout Operation The minimum on-time is the smallest duration that LTC3838's TG (top gate) pin can be in high or "on" state. It has dependency on the operating conditions of the switching regulator, and is a function of voltages on the VIN and VOUT pins, as well as the value of external resistor RT. A minimum on-time of 30ns can be achieved when the VOUT pin is tied to its minimum value of 0.6V while the VIN is tied to its maximum value of 38V. For larger values of VOUT and/or smaller values of VIN, the minimum achievable on-time will be longer. The valley mode control architecture allows low on-time, making the LTC3838 suitable for high step-down ratio applications. The effective on-time, as determined by the SW node pulse width, can be different from this TG on-time, as it also depends on external components, as well as loading conditions of the switching regulator. One of the factors that contributes to this discrepancy is the characteristics of the power MOSFETs. For example, if the top power MOSFET's turn-on delay is much smaller than the turn-off delay, the effective on-time will be longer than the TG on-time, limiting the effective minimum on-time to a larger value. Light-load operation, in forced continuous mode, will further elongate the effective on-time due to the dead times between the "on" states of TG and BG, as shown in Figure 11. During the dead time from BG turn-off to TG turn-on, the inductor current flows in the reverse direction, charging the SW node high before the TG actually turns on. The reverse current is typically small, causing a slow rising edge. On the falling edge, after the top FET turns off and before the bottom FET turns on, the SW node lingers high for a longer duration due to a smaller peak inductor current available in light load to pull the SW node low. As a result of the sluggish SW node rising and falling edges, the effective on-time is extended and not fully controlled by the TG on-time. Closer to minimum on-time, this may cause some phase jitter to appear at light load. As load current increase, the edges become sharper, and the phase locking behavior improves. 3838fb 32 For more information www.linear.com/LTC3838 LTC3838 Applications Information TG-SW (VGS OF TOP MOSFET) and/or programmed f = 2MHz (i.e., RT = 18k). In applications with different VIN, VOUT and/or f, the tON(MIN) that can be achieved will generally be larger. Also, to guarantee frequency and phase locking at light load, sufficient margin needs to be added to account for the dead times (tD(TG/BG) + tD(TG/BG) in the Electrical Characteristics). DEAD-TIME DELAYS BG (VGS OF BOTTOM MOSFET) IL 0 NEGATIVE INDUCTOR CURRENT IN FCM VIN SW 3838 F11 DURING BG-TG DEAD TIME, NEGATIVE INDUCTOR CURRENT WILL FLOW THROUGH TOP MOSFET'S BODY DIODE TO PRECHARGE SW NODE IL SW + - DURING TG-BG DEAD TIME, THE RATE OF SW NODE DISCHARGE WILL DEPEND ON THE CAPACITANCE ON THE SW NODE AND INDUCTOR CURRENT MAGNITUDE VIN L L IL TOTAL CAPACITANCE ON THE SW NODE Figure 11. Light Loading On-Time Extension for Forced Continuous Mode Operation In continuous mode operation, the minimum on-time limit imposes a minimum duty cycle of: DMIN = f * tON(MIN) where tON(MIN) is the effective minimum on-time for the switching regulator. As the equation shows, reducing the operating frequency will alleviate the minimum duty cycle constraint. If the minimum on-time that LTC3838 can provide is longer than the on-time required by the duty cycle to maintain the switching frequency, the switching frequency will have to decrease to maintain the duty cycle, but the output voltage will still remain in regulation. This is generally more preferable to skipping cycles and causing larger ripple at the output, which is typically seen in fixed frequency switching regulators. For applications that require relatively low on-time, proper caution has to be taken when choosing the power MOSFET. If the gate of the MOSFET is not able to fully turn on due to insufficient on-time, there could be significant heat dissipation and efficiency loss as a result of larger RDS(ON). This may even cause early failure of the power MOSFET. The minimum off-time is the smallest duration of time that the TG pin can be turned low and then immediately turned back high. This minimum off-time includes the time to turn on the BG (bottom gate) and turn it back off, plus the dead-time delays from TG off to BG on and from BG off to TG on. The minimum off-time that the LTC3838 can achieve is 90ns. The effective minimum off-time of the switching regulator, or the shortest period of time that the SW node can stay low, can be different from this minimum off-time. The main factor impacting the effective minimum off-time is the top and bottom power MOSFETs' electrical characteristics, such as Qg and turn-on/off delays. These characteristics can either extend or shorten the SW nodes' effective minimum off-time. Large size (high Qg) power MOSFETs generally tend to increase the effective minimum off-time due to longer gate charging and discharging times. On the other hand, imbalances in turn-on and turn-off delays could reduce the effective minimum off-time. The minimum off-time limit imposes a maximum duty cycle of: DMAX = 1 - f * tOFF(MIN) where tOFF(MIN) is the effective minimum off-time of the switching regulator. Reducing the operating frequency can alleviate the maximum duty cycle constraint. The tON(MIN) curves in the Typical Performance Characteristics are measured with minimum load on TG and BG, at extreme cases of VIN = 38V, and/or VOUT = 0.6V, 3838fb For more information www.linear.com/LTC3838 33 LTC3838 Applications Information If the maximum duty cycle is reached, due to a drooping input voltage for example, the output will drop out of regulation. The minimum input voltage to avoid dropout is: VIN(MIN) = VOUT DMAX At the onset of drop-out, there is a region of VIN of about 500mV that generates two discrete off-times, one being the minimum off time and the other being an off-time that is about 40ns to 60ns longer than the minimum off-time. This secondary off-time is due to the extra delay in tripping the internal current comparator. The two off-times average out to the required duty cycle to keep the output in regulation. There may be higher SW node jitter, apparent especially when synchronized to an external clock, but the output voltage ripple remains relatively small. Fault Conditions: Current Limiting and Overvoltage The maximum inductor current is inherently limited in a current mode controller by the maximum sense voltage. In the LTC3838, the maximum sense voltage is controlled by the voltage on the VRNG pin. With valley current mode control, the maximum sense voltage and the sense resistance determine the maximum allowed inductor valley current. The corresponding output current limit is: ILIMIT = VSENSE(MAX) RSENSE 1 + * IL 2 The current limit value should be checked to ensure that ILIMIT(MIN) > IOUT(MAX). The current limit value should be greater than the inductor current required to produce maximum output power at the worst-case efficiency. Worst-case efficiency typically occurs at the highest VIN and highest ambient temperature. It is important to check for consistency between the assumed MOSFET junction temperatures and the resulting value of ILIMIT which heats the MOSFET switches. To further limit current in the event of a short circuit to ground, the LTC3838 includes foldback current limiting. If the output falls by more than 50%, the maximum sense voltage is progressively lowered, to about one-fourth of its full value as the feedback voltage reaches 0V. A feedback voltage exceeding 7.5% of the regulated target of 0.6V is considered as overvoltage (OV). In such an OV condition, the top MOSFET is immediately turned off and the bottom MOSFET is turned on indefinitely until the OV condition is removed, i.e., the feedback voltage falling back below the 7.5% threshold by more than a hysteresis of typical 2%. Current limiting is not active during an OV. If the OV persists, and the BG turns on for a longer time, the current through the inductor and the bottom MOSFET may exceed their maximum ratings, sacrificing themselves to protect the load. OPTI-LOOP Compensation OPTI-LOOP compensation, through the availability of the ITH pin, allows the transient response to be optimized for a wide range of loads and output capacitors. The ITH pin not only allows optimization of the control-loop behavior but also provides a DC-coupled and AC-filtered closed-loop response test point. The DC step, rise time and settling at this test point truly reflects the closed-loop response. Assuming a predominantly 2nd order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The external series RITH-CITH1 filter at the ITH pin sets the dominant pole-zero loop compensation. The values can be adjusted to optimize transient response once the final PCB layout is done and the particular output capacitor type and value have been determined. The output capacitors need to be selected first because their various types and values determine the loop feedback factor gain and phase. An additional small capacitor, CITH2, can be placed from the ITH pin to SGND to attenuate high frequency noise. Note this CITH2 contributes an additional pole in the loop gain therefore can affect system stability if too large. It should be chosen so that the added pole is higher than the loop bandwidth by a significant margin. 3838fb 34 For more information www.linear.com/LTC3838 LTC3838 Applications Information The regulator loop response can also be checked by looking at the load transient response. An output current pulse of 20% to 100% of full-load current having a rise time of 1s to 10s will produce VOUT and ITH voltage transient-response waveforms that can give a sense of the overall loop stability without breaking the feedback loop. For a detailed explanation of OPTI-LOOP compensation, refer to Application Note 76. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT immediately shifts by an amount equal to ILOAD * ESR, where ESR is the effective series resistance of COUT. ILOAD also begins to charge or discharge COUT , generating a feedback error signal used by the regulator to return VOUT to its steady-state value. During this recovery time, VOUT can be monitored for overshoot or ringing that would indicate a stability problem. Connecting a resistive load in series with a power MOSFET, then placing the two directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. The initial output voltage step resulting from the step change in load current may not be within the bandwidth of the feedback loop, so it cannot be used to determine phase margin. The output voltage settling behavior is more related to the stability of the closed-loop system. However, it is better to look at the filtered and compensated feedback loop response at the ITH pin. The gain of the loop increases with the RITH and the bandwidth of the loop increases with decreasing CITH1. If RITH is increased by the same factor that CITH1 is decreased, the zero frequency will be kept the same, thereby keeping the phase the same in the most critical frequency range of the feedback loop. In addition, a feedforward capacitor, CFF , can be added to improve the high frequency response, as shown in Figure 1. Capacitor CFF provides phase lead by creating a high frequency zero with RFB2 which improves the phase margin. A more severe transient can be caused by switching in loads with large supply bypass capacitors. The discharged bypass capacitors of the load are effectively put in parallel with the converter's COUT , causing a rapid drop in VOUT . No regulator can deliver current quick enough to prevent this sudden step change in output voltage, if the switch connecting the COUT to the load has low resistance and is driven quickly. The solution is to limit the turn-on speed of the load switch driver. Hot swap controllers are designed specifically for this purpose and usually incorporate current limiting, short-circuit protection and soft starting. Load-Release Transient Detection As the output voltage requirement of step-down switching regulators becomes lower, VIN to VOUT step-down ratio increases, and load transients become faster, a major challenge is to limit the overshoot in VOUT during a fast load current drop, or "load-release" transient. Inductor current slew rate diL/dt = VL/L is proportional to voltage across the inductor VL = VSW - VOUT. When the top MOSFET is turned on, VL = VIN - VOUT, inductor current ramps up. When bottom MOSFET turns on, VL = VSW - VOUT = -VOUT, inductor current ramps down. At very low VOUT, the low differential voltage, VL, across the inductor during the ramp down makes the slew rate of the inductor current much slower than needed to follow the load current change. The excess inductor current charges up the output capacitor, which causes overshoot at VOUT. If the bottom MOSFET could be turned off during the loadrelease transient, the inductor current would flow through the body diode of the bottom MOSFET, and the equation can be modified to include the bottom MOSFET body diode drop to become VL = -(VOUT + VBD). Obviously the benefit increases as the output voltage gets lower, since VBD would increase the sum significantly, compared to a single VOUT only. The load-release overshoot at VOUT causes the error amplifier output, ITH, to drop quickly. ITH voltage is proportional 3838fb For more information www.linear.com/LTC3838 35 LTC3838 Applications Information to the inductor current setpoint. A load transient will result in a quick change of this load current setpoint, i.e., a negative spike of the first derivative of the ITH voltage. The LTC3838 uses a detect transient (DTR) pin to monitor the first derivative of the ITH voltage, and detect the loadrelease transient. Referring to the Functional Diagram, the DTR pin is the input of a DTR comparator, and the internal reference voltage for the DTR comparator is half of INTVCC. To use this pin for transient detection, ITH compensation needs an additional RITH resistor tied to INTVCC, and connects the junction point of ITH compensation components CITH1, RITH1 and RITH2 to the DTR pin as shown in the Functional Diagram. The DTR pin is now proportional to the first derivative of the inductor current setpoint, through the highpass filter of CITH1 and (RITH1//RITH2). The two RITH resistors establish a voltage divider from INTVCC to SGND, and bias the DC voltage on DTR pin (at steady-state load or ITH voltage) slightly above half of INTVCC. Compensation performance will be identical by using the same CITH1 and make RITH1//RITH2 equal the RITH as used in conventional single resistor OPTI-LOOP compensation. This will also provide the R-C time constant needed for the DTR duration. The DTR sensitivity can be adjusted by the DC bias voltage difference between DTR and half INTVCC. This difference could be set as low as 200mV, as long as the ITH ripple voltage with DC load current does not trigger the DTR. Note the internal 2.5A pull-up current from the DTR pin will generate an additional offset on top of the resistor divider itself, making the total difference between the DC bias voltage on the DTR pin and half INTVCC: RITH1 VDTR - 0.5VINTVCC = - 0.5 * 5.3V (RITH1+RITH2) + 2.5A * (RITH1 / /RITH2) As illustrated in Figure 12, when load current suddenly drops, VOUT overshoots, and ITH drops quickly. The voltage on the DTR pin will also drop quickly, since it is coupled to the ITH pin through a capacitor. If the load transient is fast enough that the DTR voltage drops below half of INTVCC, a load release event is detected. The bottom gate (BG) will be turned off, so that the inductor current flows through the body diode in the bottom MOSFET. This allows the SW node to drop below PGND by a voltage of a forward-conducted silicon diode. This creates a more negative differential voltage (VSW - VOUT) across the inductor, allowing the inductor current to drop at a faster rate to zero, therefore creating less overshoot on VOUT. The DTR comparator output is overridden by reverse inductor current detection (IREV) and overvoltage (OV) condition. This means BG will be turned off when SENSE+ is higher than SENSE- (i.e., inductor current is positive), SW 5V/DIV SW 5V/DIV BG 5V/DIV BG 5V/DIV DTR 1V/DIV BG TURNS BACK ON, INDUCTOR CURRENT (IL) GOES NEGATIVE IL 10A/DIV DTR DETECTS LOAD RELEASE, TURNS OFF BG FOR FASTER INDUCTOR CURRENT (IL) DECAY 5s/DIV LOAD RELEASE = 15A TO 0A VIN = 5V VOUT = 0.6V BG REMAINS ON DURING THE LOAD RELEASE EVENT ITH 1V/DIV IL 10A/DIV LOAD RELEASE = 15A TO 0A VIN = 5V VOUT = 0.6V (12a) DTR Enabled 5s/DIV 3838 F12 (12b) DTR Disabled Figure 12. Comparison of VOUT Overshoot with Detect Transient (DTR) Feature Enabled and Disabled 3838fb 36 For more information www.linear.com/LTC3838 LTC3838 Applications Information as long as the OV condition is not present. When inductor current drops to zero and starts to reverse, BG will turn back on in forced continuous mode (e.g., the MODE/ PLLIN pin tied to INTVCC, or an input clock is present), even if DTR is still below half INTVCC. This is to allow the inductor current to go negative to quickly pull down the VOUT overshoot. Of course, if the MODE/PLLIN pin is set to discontinuous mode (i.e., tied to SGND), BG will stay off as inductor current reverse, as it would with the DTR feature disabled. Also, if VOUT gets higher than the OV window (7.5% typical), the DTR function is defeated and BG will turn on regardless. Therefore, in order for the DTR feature to reduce VOUT overshoot effectively,sufficient output capacitance needs to be used in the application so that OV is not triggered with the amount of load step desired to have its overshoot suppressed. Experimenting with a 0.6V output application (modified from the design example circuit by setting VOUT to 0.6V and ITH compensation adjusted accordingly) shows this detect transient feature significantly reduces the overshoot peak voltage, as well as time to resume regulation during load release steps (see application examples in Typical Performance Characteristics). Note that it is expected that this DTR feature will cause additional loss on the bottom MOSFET, due to its body diode conduction. The bottom MOSFET temperature may be higher with a load of frequent and large load steps. This is an important design consideration. Experiments on the demo board shows a 20C increase when a continuous 100% to 50% load step pulse train with 50% duty cycle and 100kHz frequency is applied to the output. If not needed, this DTR feature can be disabled by tying the DTR pin to INTVCC, or simply leave the DTR pin open so that an internal 2.5A current source will pull itself up to INTVCC. Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. Percentage efficiency can be expressed as: %Efficiency = 100% - (L1% + L2% + L3% + ...) where L1%, L2%, etc. are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce power losses, several main sources usually account for most of the losses in LTC3838 circuits: 1. I2R loss. These arise from the DC resistances of the MOSFETs, inductor, current sense resistor and is the majority of power loss at high output currents. In continuous mode the average output current flows though the inductor L, but is chopped between the top and bottom MOSFETs. If the two MOSFETs have approximately the same RDS(ON), then the resistance of one MOSFET can simply be summed with the inductor's DC resistances (DCR) and the board traces to obtain the I2R loss. For example, if each RDS(ON) = 8m, RL = 5m, and RSENSE = 2m the loss will range from 15mW to 1.5W as the output current varies from 1A to 10A. This results in loss from 0.3% to 3% a 5V output, or 1% to 10% for a 1.5V output. Efficiency varies as the inverse square of VOUT for the same external components and output power level. The combined effects of lower output voltages and higher currents load demands greater importance of this loss term in the switching regulator system. 2. Transition loss. This loss mostly arises from the brief amount of time the top MOSFET spends in the saturation (Miller) region during switch node transitions. It depends upon the input voltage, load current, driver strength and MOSFET capacitance, among other factors, and can be significant at higher input voltages or higher switching frequencies. 3838fb For more information www.linear.com/LTC3838 37 LTC3838 Applications Information 3. DRVCC current. This is the sum of the MOSFET driver and INTVCC control currents. The MOSFET driver currents result from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge dQ moves from DRVCC to ground. The resulting dQ/dt is a current out of DRVCC that is typically much larger than the controller IQ current. In continuous mode, IGATECHG = f * (Qg(TOP) + Qg(BOT)), where Qg(TOP) and Qg(BOT) are the gate charges of the top and bottom MOSFETs, respectively. Supplying DRVCC power through EXTVCC could save several percents of efficiency, especially for high VIN applications. Connecting EXTVCC to an output-derived source will scale the VIN current required for the driver and controller circuits by a factor of (Duty Cycle)/(Efficiency). For example, in a 20V to 5V application, 10mA of DRVCC current results in approximately 2.5mA of VIN current. This reduces the mid-current loss from 10% or more (if the driver was powered directly from VIN) to only a few percent. 4. CIN loss. The input capacitor filters large square-wave input current drawn by the regulator into an averaged DC current from the supply. The capacitor itself has a zero average DC current, but square-wave-like AC current flows through it. Therefore the input capacitor must have a very low ESR to minimize the RMS current loss on ESR. It must also have sufficient capacitance to filter out the AC component of the input current to prevent additional RMS losses in upstream cabling, fuses or batteries. The LTC3838 2-phase architecture improves the ESR loss. "Hidden" copper trace, fuse and battery resistance, even at DC current, can cause a significant amount of efficiency degradation, so it is important to consider them during the design phase. Other losses, which include the COUT ESR loss, bottom MOSFET 's body diode reverse-recovery loss, and inductor core loss generally account for less than 2% additional loss. Power losses in the switching regulator will reflect as a higher than ideal duty cycle, or a longer on-time for a constant frequency. This efficiency accounted on-time can be calculated as: tON tON(IDEAL)/Efficiency When making adjustments to improve efficiency, the input current is the best indicator of changes in efficiency. If you make a change and the input current decreases, then the efficiency has increased. Design Example Consider a channel of step-down converter from VIN = 4.5V to 26V to VOUT = 1.2V, with IOUT(MAX) = 15A, and f = 350kHz (see Figure 13, Channel 1. The regulated output voltage is determined by: R VOUT = 0.6V * 1+ FB2 RFB1 Using a 10k resistor for RFB1, RFB2 is also 10k. The frequency is programmed by: R T [k ] = 41550 41550 - 2.2 = - 2.2 116.5 f [kHz ] 350 Use the nearest 1% resistor standard value of 115k. The minimum on-time occurs for maximum VIN. Using the tON(MIN) curves in the Typical Performance Characteristics as references, make sure that the tON(MIN) at maximum VIN is greater than that the LTC3838 can achieve, and allow sufficient margin to account for the extension of effective on-time at light load due to the dead times (tD(TG/BG) + tD(TG/BG) in the Electrical Characteristics). The minimum on-time for this application is: tON(MIN) = VOUT VIN(MAX) * f = 1.2V = 143ns 24V * 350kHz 3838fb 38 For more information www.linear.com/LTC3838 LTC3838 Applications Information VIN 4.5V TO 26V + CIN1 220F CIN2 10F x3 2.2 1F VIN 0.1F 3.57k VOUT1 1.2V 15A + COUT2 330F x2 SENSE2- SENSE1+ SENSE2+ BOOST1 BOOST2 0.1F TG1 MT1 3.57k TG2 MT2 DB2 SW1 4.7F 1F 15k 0.1F DB1 2.2 COUT1 100F x2 SENSE1- 0.1F 15k L1 0.56H LTC3838 DRVCC1 INTVCC DRVCC2 EXTVCC BG2 VOUTSENSE1+ PGOOD1 0.01F 90.9k 10k VOUTSENSE1- PGOOD1 220pF 82.5k 115k ITH1 DTR1 VRNG1 RT SGND RUN1 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 50 40 1.0 VIN = 12V VOUT = 1.2V 0.1 1 LOAD CURRENT (A) 10 82.5k DTR2 VRNG2 3838 F13a PHASMD MODE/PLLIN CLKOUT RUN2 3.0 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 2.5 2.0 80 EFFICIENCY 70 60 0.5 50 0 40 1.5 POWER LOSS 1.0 VIN = 12V VOUT = 1.5V 0.1 1 LOAD CURRENT (A) 3838 F13b 10 POWER LOSS (W) 60 90.9k 90 1.5 POWER LOSS 220pF 2.5 EFFICIENCY 70 ITH2 CIN1: PANASONIC EEEFK1V221P CIN2: TAIYO YUDEN GMK325BJ106MN-T COUT2, COUT4: SANYO 2R5TPE330M9 COUT1, COUT3: MURATA GRM31CR60J107ME39L DB1, DB2: CENTRAL SEMI CMDSH-4ETR L1, L2: VISHAY IHLP4040DZERR56M01 MT1, MT2: RENESAS RJK0305DPB MB1, MB2: RENESAS RJK0330DPB 22pF 100 2.0 80 0.01F 3.0 POWER LOSS (W) EFFICIENCY (%) 90 100k PGOOD2 EFFICIENCY (%) 100 PGOOD2 TRACK/SS1 TRACK/SS2 22pF COUT3 100F x2 15k VFB2 10k 100k COUT4 + 330F x2 MB2 PGND 10k VOUT2 1.5V 15A SW2 BG1 MB1 L2 0.56H 0.5 0 3838 F13c Figure 13. Design Example: 4.5V to 26V Input, 1.2V/15A and 1.5V/15A Dual Outputs, 350kHz, DCR Sense, DTR Enabled, Step-Down Converter 3838fb For more information www.linear.com/LTC3838 39 LTC3838 Applications Information Set the inductor value to give 40% ripple current at maximum VIN using the adjusted operating frequency: 1.2V 1.2V L= 1- = 0.54H 350kHz * 40% * 15A 24V Select 0.56H which is the nearest standard value. The resulting maximum ripple current is: 1.2V 1.2V IL = = 5.8A 1- 350kHz * 0.56H 24V Often in a high power application, DCR current sensing is preferred over RSENSE in order to maximize efficiency. In order to determine the DCR filter values, first the inductor manufacturer has to be chosen. For this design, the Vishay IHLP-4040DZ-01 model is chosen with a value of 0.56H and a DCRMAX =1.8m. This implies that: VSENSE(MAX) = 1.8m * [1 + (100C - 25C) * 0.4%/C] * (15A - 5.8A/2) = 28mV The maximum sense voltage, VSENSE(MAX), is within the range that LTC3838 can handle without any additional scaling. Therefore, the DCR filter can use a simple RC filter across the inductor. If the C is chosen to be 0.1F, then the R can be calculated as: RDCR = L 0.56H = = 3.1k DCR * CDCR 1.8m * 0.1F The resulting VRNG pin voltage is: VRNG = VSENSE(MAX) 0.05 = 28mV * 20 = 0.56V This voltage can be generated with a resistive divider from the INTVCC pin to signal ground (SGND). To make sure that the maximum load current of 15A can be supplied under all conditions, such as lower INTVCC due to a lower VIN, and account for the range of LTC3838's own VSENSE(MAX) variation within specification, a higher VRNG should be used to provide margin. A better and the recommended way to set VRNG is to simply tie the VRNG pin to SGND for an equivalent of VRNG = 0.6V, while using an additional resistor in the DCR filter, as discussed in DCR Inductor Current Sensing, to scale the VSENSE(MAX) down by a comfortable margin below the lower limit of the LTC3838's own VSENSE(MAX) specification, so that the maximum output current can be guaranteed. In this design example, a 3.57k and 15k resistor divider is used. The previously calculated VSENSE(MAX) is scaled down from 28mV to 22.6mV, which is close to the lower limit of LTC3838's VSENSE(MAX) specification at VRNG = 0.6V. Note the equivalent RDCR = 3.57k//15k = 2.9k, slightly lower than the 3.1k calculated above for a matched RDCR-CDCR and L-DCR network. The resulted mismatch allows for a slightly higher ripple in VSENSE. Remember to check the peak inductor current, considering the upper spec limit of VSENSE(MAX) and the DCR(MIN) at lowest operating temperature, is not going to saturate the inductor or exceed the rating of power MOSFETs. For the external N-channel MOSFETs, Renesas RJK0305DBP (RDS(ON) = 13m max, CMILLER = 150pF, VGS = 4.5V, JA = 40C/W, TJ(MAX) = 150C) is chosen for the top MOSFET (main switch). RJK0330DBP (RDS(ON) = 3.9m max, VGS = 4.5V, JA = 40C/W, TJ(MAX) = 150C) is chosen for the bottom MOSFET (synchronous switch). The power dissipation for each MOSFET can be calculated for VIN = 24V and typical TJ = 125C: 1.2V PTOP = (15A )2 (13m) 1+ 0.4% (125C - 25C) 24V 1.2 2.5 2 15A + ( 24V ) + (150pF ) 5.3V (350kHz ) 2 3V - 3V = 0.54W 24V - 1.2V PBOT = (15A )2 (3.9m) 1+ 0.4% (125C - 25C) 24V = 1.2W The resulted junction temperatures at an ambient temperature TA = 75C are: TJ(TOP) = 75C + (0.54W)(40C/W) = 97C TJ(BOT) = 75C + (1.2W)(40C/W) = 123C 3838fb 40 For more information www.linear.com/LTC3838 LTC3838 Applications Information These numbers show that careful attention should be paid to proper heat sinking when operating at higher ambient temperatures. Select the CIN capacitors to give ample capacitance and RMS ripple current rating. Consider worst-case duty cycles per Figure 6: If operated at steady-state with SW nodes fully interleaved, the two channels would generate not more than 7.5A RMS at full load. In this design example, 3 x 10F 35V X5R ceramic capacitors are put in parallel to take the RMS ripple current, with a 220F aluminumelectrolytic bulk capacitor for stability. For 10F 1210 X5R ceramic capacitors, try to keep the ripple current less than 3A RMS through each device. The bulk capacitor is chosen for RMS rating per simulation with the circuit model provided. The output capacitor COUT is chosen for a low ESR of 4.5m to minimize output voltage changes due to inductor ripple current and load steps. The output voltage ripple is given as: VOUT(RIPPLE) = IL(MAX) * ESR = 5.85A * 4.5m = 26mV However, a 10A load step will cause an output change of up to: VOUT(STEP) = ILOAD * ESR = 10A * 4.5m = 45mV Optional 2 x 100F ceramic output capacitors are included to minimize the effect of ESR and ESL in the output ripple and to improve load step response. The ITH compensation resistor RITH of 40k and a CITH of 220pF are chosen empirically for fast transient response, and an additional CITH2 = 22pF is added directly from ITH pin to SGND, to roll off the system gain at switching frequency and attenuate high frequency noise. To set up the detect transient (DTR) feature, pick resistors for an equivalent RITH = RITH1//RITH2 close to the 40k. Here, 1% resistors RITH1 = 90.9k (low side) and RITH2 = 82.5k (high side) are used, which yields an equivalent RITH of 43.2k, and a DC-bias threshold of 128mV above one-half of INTVCC. Note that even though the accuracy of the equivalent compensation resistance RITH is not as important, always use 1% or better resistors for the resistor divider from INTVCC to SGND to guarantee the relative accuracy of this DC-bias threshold. To disable the DTR feature, simply use a single RITH resistor to SGND, and tie the DTR pin to INTVCC. PCB Layout Checklist The printed circuit board layout is illustrated graphically in Figure 14. Figure 15 illustrates the current waveforms present in the various branches of 2-phase synchronous regulators operating in continuous mode. Use the following checklist to ensure proper operation of the LTC3838: * A multilayer printed circuit board with dedicated ground planes is generally preferred to reduce noise coupling and improve heat sinking. The ground plane layer should be immediately next to the routing layer for the power components, e.g., MOSFETs, inductors, sense resistors, input and output capacitors etc. * Keep SGND and PGND separate. Upon finishing the layout, connect SGND and PGND together with a single PCB trace underneath the IC from the SGND pin through the exposed PGND pad to the PGND pin. * All power train components should be referenced to PGND; all components connected to noise-sensitive pins, e.g., ITH, RT , TRACK/SS and VRNG, should return to the SGND pin. Keep PGND ample, but SGND area compact. Use a modified "star ground" technique: a low impedance, large copper area central PCB point on the same side of the as the input and output capacitors. * Place power components, such as CIN, COUT , MOSFETs, DB and inductors, in one compact area. Use wide but shortest possible traces for high current paths (e.g., VIN, VOUT , PGND etc.) to this area to minimize copper loss. 3838fb For more information www.linear.com/LTC3838 41 LTC3838 Applications Information DTR2 SENSE2- RFB2(2) CSS2 RFB1(2) SENSE2+ VFB2 TRACK/SS2 RITH2(2) CITH1(2) RITH1(2) ITH2 CITH2(2) L2 DB2 DRVCC2 EXTVCC MT2 RSENSE2 VOUT2 MB2 RINTVCC CERAMIC CINTVCC COUT2 PGND CVIN VIN VRNG1 CDRVCC VIN RVIN + PGND CIN CERAMIC + CITH2(1) RT CB2 + VRNG2 PHASMD MODE/PLLIN CLKOUT SGND RT COUT1 DRVCC1 RITH1(1) DB1 ITH1 CITH1(1) TRACK/SS1 RFB2(1) TG2 SW2 BG2 INTVCC LOCALIZED SGND TRACE RITH2(1) RUN2 PGOOD2 BOOST2 CSS1 RFB1(1) VOUTSENSE1+ VOUTSENSE1- SENSE1+ SENSE1- MT1 MB1 BG1 SW1 RSENSE1 TG1 VOUT1 L1 CB1 BOOST1 PGOOD1 RUN1 DTR1 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. Figure 14. Recommended PCB Layout Diagram * Keep the switch nodes (SW1,2), top gates (TG1,2) and boost nodes (BOOST1,2) away from noise-sensitive small-signal nodes, especially from the opposite channel's voltage and current sensing feedback pins. These nodes have very large and fast moving signals and therefore should be kept on the "output side" of the LTC3838 (power-related pins are toward the right hand side of the IC), and occupy minimum PC trace area. Use compact switch node (SW) planes to improve cooling of the MOSFETs and to keep EMI down. If DCR sensing is used, place the top filter resistor (R1 only in Figure 5) close to the switch node. 3838fb 42 For more information www.linear.com/LTC3838 LTC3838 Applications Information SW2 L2 RSENSE2 VOUT2 COUT2 RL2 VIN RIN CIN SW1 L1 RSENSE1 VOUT1 COUT1 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. RL1 3838 F15 Figure 15. Branch Current Waveforms * The top N-channel MOSFETs of the two channels have to be located within a short distance from (preferably <1cm) each other with a common drain connection at CIN. Do not attempt to split the input decoupling for the two channels as it can result in a large resonant loop. * Connect the input capacitor(s), CIN, close to the power MOSFETs. This capacitor provides the MOSFET transient spike current. Connect the drain of the top MOSFET as close as possible to the (+) plate of the ceramic portion of input capacitors CIN. Connect the source of the bottom MOSFET as close as possible to the (-) terminal of the same ceramic CIN capacitor(s). These ceramic capacitor(s) bypass the high di/dt current locally, and both top and bottom MOSFET should have short PCB trace lengths to minimize high frequency EMI and prevent MOSFET voltage stress from inductive ringing. 3838fb For more information www.linear.com/LTC3838 43 LTC3838 Applications Information * The path formed by the top and bottom N-channel MOSFETs, and the CIN capacitors should have short leads and PCB trace. The (-) terminal of output capacitors should be connected close to the (-) terminal of CIN, but away from the loop described above. This is to achieve an effect of Kevin (4-wire) connection to the input ground so that the "chopped" switching current will not flow through the path between the input ground and the output ground, and cause common mode output voltage ripple. * Place decoupling capacitors CITH2 next to the ITH and SGND pins with short, direct trace connections. * Several smaller sized ceramic output capacitors, COUT , can be placed close to the sense resistors and before the rest bulk output capacitors. * Place the ceramic decoupling capacitor CINTVCC between the INTVCC pin and SGND and as close as possible to the IC. * The filter capacitor between the SENSE+ and SENSE- pins should always be as close as possible to these pins. Ensure accurate current sensing with Kevin (4-wire) connections to the soldering pads from underneath the sense resistors or inductor. A pair of sense traces should be routed together with minimum spacing. RSENSE, if used, should be connected to the inductor on the noiseless output side, and its filter resistors close to the SENSE+/SENSE- pins. For DCR sensing, however, filter resistor should be placed close to the inductor, and away from the SENSE+/SENSE- pins, as its terminal is the SW node. * Place the ceramic decoupling capacitor CDRVCC close to the IC, between the combined DRVCC1,2 pins and PGND. * Keep small-signal components connected noise-sensitive pins (give priority to SENSE+/SENSE-, VOUTSENSE1+/ VOUTSENSE1-, VFB2, RT , ITH, VRNG pins) on the left hand side of the IC as close to their respective pins as possible. This minimizes the possibility of noise coupling into these pins. If the LTC3838 can be placed on the bottom side of a multilayer board, use ground planes to isolate from the major power components on the top side of the board, and prevent noise coupling to noise sensitive components on the bottom side. * Place the resistor feedback divider RFB1, RFB2 close to VOUTSENSE1+ and VOUTSENSE1- pins for Channel 1, or VFB2 pin for Channel 2, so that the feedback voltage tapped from the resistor divider will not be disturbed by noise sources. Route remote sense PCB traces (use a pair of wires closely together for differential sensing in Channel 1) directly to the terminals of output capacitors for best output regulation. * Use sufficient isolation when routing a clock signal into the MODE/PLLIN pin or out of the CLKOUT pin, so that the clock does not couple into sensitive pins. * Filter the VIN input to the LTC3838 with an RC filter. Place the filter capacitor close to the VIN pin. * If vias have to be used, use immediate vias to connect components to the SGND and PGND planes of LTC3838. Use multiple large vias for power components. * Flood all unused areas on all layers with copper. Flooding with copper will reduce the temperature rise of power components. Connect the copper areas to DC rails only, e.g., PGND. PCB Layout Debugging Only after each controller is checked for its individual performance should both controllers be turned on at the same time. It is helpful to use a current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator output CLKOUT, or external clock if used. Probe the actual output voltage as well. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range. The phase should be maintained 3838fb 44 For more information www.linear.com/LTC3838 LTC3838 Applications Information from cycle to cycle in a well designed, low noise PCB implementation. Variation in the phase of SW node pulse can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PCB layout if regulator bandwidth optimization is not required. Pay special attention to the region of operation when one controller channel is turning on (right after its current comparator trip point) while the other channel is turning off its top MOSFET at the end of its on-time. This may cause minor phase-lock jitter at either channel due to noise coupling. Reduce VIN from its nominal level to verify operation of the regulator in dropout. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with high current output loading at lower input voltages, look for inductive coupling between CIN, top and bottom MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the SGND pin of the IC. High Switching Frequency Operation At high switching frequencies there may be an increased sensitivity to noise. Special care may need to be taken to prevent cycle-by-cycle instability and/or phase-lock jitter. First, carefully follow the recommended layout techniques to reduce coupling from the high switching voltage/current traces. Additionally, use low ESR and low impedance X5R or X7R ceramic input capacitors: up to 5F per Ampere of load current may be needed. If necessary, increase ripple sense voltage by increasing sense resistance value and VRNG setting, to improve noise immunity. 3838fb For more information www.linear.com/LTC3838 45 LTC3838 Typical Applications VIN 4.5V TO 38V + CIN1 100F CIN2 10F x3 2.2 1F VIN 0.1F 3.57k VOUT1 1.2V 15A + COUT2 330F x2 SENSE2- SENSE1+ SENSE2+ BOOST1 BOOST2 0.1F TG1 MT1 3.57k TG2 MT2 DB2 SW1 4.7F 1F 15k 0.1F DB1 2.2 COUT1 100F x2 SENSE1- 0.1F 15k L1 0.56H LTC3838 DRVCC1 INTVCC DRVCC2 EXTVCC BG2 VOUTSENSE1+ PGOOD1 0.01F 40.2k 10k VOUTSENSE1- PGOOD1 220pF 115k ITH1 DTR1 VRNG1 RT SGND RUN1 100 220pF DTR2 VRNG2 3838 F16a PHASMD MODE/PLLIN CLKOUT RUN2 POWER LOSS 60 1.0 0.5 50 VIN = 12V VOUT = 1.2V 0.1 1 LOAD CURRENT (A) 0 10 3.0 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 90 EFFICIENCY (%) 70 40.2k 2.5 2.0 80 EFFICIENCY POWER LOSS 70 1.5 1.0 60 50 40 VIN = 12V VOUT = 1.5V 0.1 3838 F16b 1 LOAD CURRENT (A) 10 POWER LOSS (W) EFFICIENCY (%) ITH2 CIN1: NICHICON UCJ1H101MCL165 CIN2: MURATA GRM32ER71H106K COUT2, COUT4: SANYO 2R5TPE330M9 COUT1, COUT3: MURATA GRM31CR60J107ME39L DB1, DB2: DIODES INC. SDM10K45 L1, L2: TOKO FDA1055-R56M MT1, MT2: INFINEON BSC093N04LSG MB1, MB2: INFINEON BSC035N04LSG 22pF 100 POWER LOSS (W) 1.5 EFFICIENCY 40 0.01F 2.0 80 100k PGOOD2 2.5 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 90 PGOOD2 TRACK/SS1 TRACK/SS2 22pF COUT3 100F x2 15k VFB2 10k 100k COUT4 + 330F x2 MB2 PGND 10k VOUT2 1.5V 15A SW2 BG1 MB1 L2 0.56H 0.5 0 3838 F16c Figure 16. 4.5V to 38V Input, 1.2V/15A and 1.5V/15A Dual Output, 350kHz, DCR Sense, Step-Down Converter 3838fb 46 For more information www.linear.com/LTC3838 LTC3838 Typical Applications VIN 6V TO 26V + CIN1 220F CIN2 10F x3 2.2 1F VIN 100 L1 0.47H MT1 + COUT2 330F x2 SENSE1+ SENSE2+ BOOST1 BOOST2 TG1 100 MT2 TG2 DB2 SW1 4.7F 1F MB1 100 0.1F DB1 2.2 COUT1 100F x2 SENSE2- 1nF 0.1F RS1 0.002 SENSE1- 1nF 100 VOUT1 1.2V 12A LTC3838 SW2 DRVCC1 INTVCC DRVCC2 EXTVCC BG1 MB2 BG2 PGND 10k VOUTSENSE1+ PGOOD1 0.01F 39.2k 60.4k 10k PGOOD2 TRACK/SS1 TRACK/SS2 22pF 220pF 115k ITH1 DTR1 VRNG1 RT SGND RUN1 COUT3 330F x2 + VOUT2 1.5V 12A COUT4 100F x2 10k VOUTSENSE1- PGOOD1 RS2 0.002 15k VFB2 10k 100k L2 0.47H ITH2 100k PGOOD2 0.01F CIN1: PANASONIC EEEFK1V221P CIN2: TAIYO YUDEN GMK325BJ106MN-T COUT1, COUT4: MURATA GRM31CR60J107ME39L COUT2, COUT3: SANYO 2R5TPE330M9 DB1, DB2: CENTRAL SEMI CMDSH-4ETR L1, L2: WURTH 7443330047 MT1, MT2: RENESAS RJK0305DPB MB1, MB2: RENESAS RJK0330DPB 22pF 220pF 39.2k DTR2 VRNG2 PHASMD MODE/PLLIN CLKOUT RUN2 10k 60.4k 3838 F17 Figure 17. 6V to 26V Input, 1.2V/15A and 1.5V/15A Dual Output, 350kHz, RSENSE, Step-Down Converter 3838fb For more information www.linear.com/LTC3838 47 LTC3838 Typical Applications VIN 4.5V TO 14V + CIN2 22F x4 CIN1 180F 2.2 1F VIN LTC3838 SENSE1- SENSE2- SENSE1+ SENSE2+ BOOST1 BOOST2 0.1F 0.1F 2.55k L1 0.36H VOUT 1.2V 50A MT1 TG1 + COUT2 330F x2 0.1F 2.55k MT2 TG2 DB1 SW1 4.7F 1F L2 0.36H DB2 2.2 COUT1 100F x2 0.1F MB1 SW2 DRVCC1 INTVCC DRVCC2 EXTVCC BG1 COUT3 + 330F x2 MB2 BG2 COUT4 100F x2 PGND 10k VOUTSENSE1+ VFB2 10k 100k PGOOD 0.01F 470pF 35.7k CIN1: SANYO 16SVP180MX CIN2: TDK C3225X5R1C226MT COUT1, COUT4: MURATA GRM31CR60J107ME39L COUT2, COUT3: SANYO 2R5TPE330M9 DB1, DB2: CENTRAL SEMI CMDSH-4ETR L1, L2: VISHAY IHLP4040DZERR36M01 MT1, MT2: INFINEON BSC050NE2LS MB1, MB2: INFINEON BSC010NE2LS 137k 60 3838 F18b 10 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 8 80 EFFICIENCY POWER LOSS 6 70 4 2 60 2 0 50 0.1 1 10 LOAD CURRENT (A) VIN = 5V VOUT = 1.2V POWER LOSS (W) EFFICIENCY (%) 90 4 0.1 1 10 VIN = 12V LOAD CURRENT (A) VOUT = 1.2V 3838 F18 PHASMD MODE/PLLIN CLKOUT RUN2 8 6 POWER LOSS DTR2 VRNG2 100 70 50 RT ITH2 10 POWER LOSS (W) EFFICIENCY DTR1 VRNG1 RUN1 90 80 ITH1 SGND FORCED CONTINUOUS MODE DISCONTINUOUS MODE PGOOD2 EFFICIENCY (%) 100 PGOOD1 TRACK/SS1 TRACK/SS2 47pF 41.2k VOUTSENSE1- 0 3838 F18c Figure 18. 4.5V to 14V Input, 1.2V/50A 2-Phase Single Output, 300kHz, DCR Sense, DTR Enabled, Step-Down Converter 3838fb 48 For more information www.linear.com/LTC3838 LTC3838 Typical Applications VIN 6.5V TO 34V + CIN2 10F x3 CIN1 220F 2.2 1F VIN 20 VOUT1 5V 12A MT1 + COUT2 150F x2 SENSE1+ SENSE2+ BOOST1 BOOST2 20 TG1 MT2 TG2 DB2 SW1 4.7F 1F MB1 20 0.1F DB1 2.2 COUT1 100F SENSE2- 1nF 0.1F L1 2.2H SENSE1- 1nF 20 RS1 0.002 LTC3838 SW2 DRVCC1 INTVCC DRVCC2 EXTVCC BG1 VOUT1 PGOOD1 0.01F 220pF 137k ITH1 DTR1 VRNG1 RT SGND RUN1 ITH2 100k PGOOD2 CIN1: PANASONIC EEEFK1V221P CIN2: TAIYO YUDEN GMK325BJ106MN-T COUT1, COUT4: MURATA GRM31CR60J107ME39L COUT2: SANYO 6TPE150MIC2 COUT3: SANYO 4TPD330M DB1, DB2: DIODES INC. SDM10K45 L1: WURTH 7443320220 L2: WURTH 7443551130 MT1, MT2: INFINEON BSC093N04LSG MB1, MB2: INFINEON BSC035N04LSG 0.01F 22pF 220pF 45.3k DTR2 VRNG2 PHASMD MODE/PLLIN CLKOUT RUN2 3838 F19 3.0 100 3.0 90 2.5 90 2.5 EFFICIENCY 70 60 50 40 1.5 POWER LOSS 1.0 VIN = 12V VOUT = 5V 0.1 1 LOAD CURRENT (A) 10 2.0 80 EFFICIENCY 70 60 0.5 50 0 40 1.5 POWER LOSS 1.0 VIN = 12V VOUT = 3.3V 0.1 3838 F19b 1 LOAD CURRENT (A) 10 POWER LOSS (W) 2.0 80 EFFICIENCY (%) 100 POWER LOSS (W) EFFICIENCY (%) PGOOD2 TRACK/SS1 TRACK/SS2 22pF 53.6k 10k VOUTSENSE1- PGOOD1 COUT4 100F 45.3k VFB2 10k 100k + VOUT2 3.3V 12A MB2 BG2 VOUTSENSE1+ RS2 0.002 COUT3 330F PGND 73.2k L2 1.3H 0.5 0 3838 F19c FORCED CONTINUOUS MODE DISCONTINUOUS MODE FORCED CONTINUOUS MODE DISCONTINUOUS MODE Figure 19. 6.5V to 34V Input, 5V/12A and 3.3V/12A Dual Output, 300kHz, RSENSE, 5V Output Tied to EXTVCC, Step-Down Converter 3838fb For more information www.linear.com/LTC3838 49 LTC3838 Typical Applications + CIN1 39F CIN2 10F x3 2.2 1F RS1 0.008 MT1 SENSE1+ SENSE2+ BOOST1 BOOST2 TG1 4.7F MB1 DRVCC1 INTVCC 24.9k 330pF 18.7k PGOOD1 DTR1 VRNG1 RT 330pF 35.7k DTR2 VRNG2 3838 F20a 2.5 90 2.0 80 1.5 80 1.5 70 EFFICIENCY 1.0 POWER LOSS 0.5 0.5 60 50 0.01 0.1 1 VIN = 12V LOAD CURRENT (A) VOUT = 5V EXTVCC TIED TO VOUT 0 0 50 0.01 0.1 1 VIN = 12V LOAD CURRENT (A) VOUT = 3.3V 3838 F20c EXTVCC TIED TO 5V BIAS SUPPLY EFFICIENCY MEASUREMENTS INCLUDE POWER FROM THE 5V BIAS SUPPLY FORCED CONTINUOUS MODE DISCONTINUOUS MODE EFFICIENCY 1.0 70 60 POWER LOSS 50 0.01 0.1 1 VIN = 12V LOAD CURRENT (A) VOUT = 3.3V EXTVCC FLOATING POWER LOSS (W) 2.0 FORCED CONTINUOUS MODE DISCONTINUOUS MODE 60 3838 F20b CIN1: SANYO 16SVP39M CIN2: MURATA GRM32DR61E106K COUT1, COUT2: TAIYO YUDEN LMK325BJ476MM-T DB1, DB2: CENTRAL CMDSH-3 L1, L2: COILCRAFT XAL5030-801MEB MT1, MB1, MT2, MB2: VISHAY SI7114ADN PHASMD MODE/PLLIN CLKOUT RUN2 POWER LOSS (W) EFFICIENCY (%) 22pF 90 2.0 POWER LOSS (W) EFFICIENCY (%) 0.01F 100 100 1.0 100k PGOOD2 2.5 2.5 1.5 POWER LOSS PGOOD2 ITH2 RUN1 80 - ITH1 SGND 90 68pF 10k VOUTSENSE1 VOUT2 3.3V 5A 45.3k VFB2 TRACK/SS1 TRACK/SS2 22pF FORCED CONTINUOUS MODE DISCONTINUOUS MODE MB2 10k PGOOD1 RS2 0.008 COUT2 47F x2 VOUT1 BG2 VOUTSENSE1+ 0.01F 70 DRVCC2 EXTVCC PGND 100k L2 0.8H SW2 BG1 47pF EFFICIENCY MT2 TG2 SW1 1F 10 0.1F DB2 73.2k 100 10 DB1 2.2 COUT1 47F x2 SENSE2- 1nF 0.1F VOUT1 5V 5A SENSE1- 1nF 10 L1 0.8H LTC3838 VIN 10 EFFICIENCY (%) VIN 7V TO 14V 0.5 0 3838 F20d Figure 20. 7V to 14V Input, 5V/5A and 3.3V/5A Dual Output, 2MHz, RSENSE, Step-Down Converter with EXTVCC Tied to 5V Output 3838fb 50 For more information www.linear.com/LTC3838 LTC3838 Package Description Please refer to http://www.linear.com/product/LTC3838#packaging for the most recent package drawings. UHF Package 38-Lead Plastic QFN (5mm x 7mm) (Reference LTC DWG # 05-08-1701 Rev C) 0.70 0.05 5.50 0.05 5.15 0.05 4.10 0.05 3.00 REF 3.15 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC 5.5 REF 6.10 0.05 7.50 0.05 RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 0.75 0.05 5.00 0.10 PIN 1 NOTCH R = 0.30 TYP OR 0.35 x 45 CHAMFER 3.00 REF 37 0.00 - 0.05 38 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 1 2 5.15 0.10 5.50 REF 7.00 0.10 3.15 0.10 (UH) QFN REF C 1107 0.200 REF 0.25 0.05 0.50 BSC R = 0.125 TYP R = 0.10 TYP BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE M0-220 VARIATION WHKD 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3838fb For more information www.linear.com/LTC3838 51 LTC3838 Package Description Please refer to http://www.linear.com/product/LTC3838#packaging for the most recent package drawings. FE Package 38-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1772 Rev C) Exposed Pad Variation AA 4.75 REF 38 9.60 - 9.80* (.378 - .386) 4.75 REF (.187) 20 6.60 0.10 4.50 REF 2.74 REF SEE NOTE 4 6.40 2.74 REF (.252) (.108) BSC 0.315 0.05 1.05 0.10 0.50 BSC RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS 2. DIMENSIONS ARE IN MILLIMETERS (INCHES) 3. DRAWING NOT TO SCALE 1 0.25 REF 19 1.20 (.047) MAX 0 - 8 0.50 (.0196) BSC 0.17 - 0.27 (.0067 - .0106) TYP 0.05 - 0.15 (.002 - .006) FE38 (AA) TSSOP REV C 0910 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 3838fb 52 For more information www.linear.com/LTC3838 LTC3838 Revision History REV DATE DESCRIPTION PAGE NUMBER A 6/12 Electrical specs clarification, 4.6V EXTVCC switch over B 3/16 Modified Table 1 3, 4, 5, 13 2 3838fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representaFor more information www.linear.com/LTC3838 tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. 53 LTC3838 Typical Application 4.5V to 26V Input, 2.5V/4A and 1.8V/4A Dual Output, 1MHz, RSENSE, Dual Channel Power FETs, Step-Down Converter VIN 4.5V TO 26V + CIN1 47F CIN2 10F x3 2.2 1F VIN 20 SENSE2- SENSE1+ SENSE2+ BOOST1 BOOST2 20 1nF 0.1F M1 VOUT1 2.5V 4A SENSE1- 1nF 20 RS1 0.006 LTC3838 TG1 L1 1.2H M2 TG2 DB1 SW1 4.7F 1F SW2 DRVCC1 INTVCC DRVCC2 EXTVCC BG1 BG2 VOUTSENSE1+ PGOOD1 75k 100pF 10k VOUTSENSE1- PGOOD1 PGOOD2 TRACK/SS1 TRACK/SS2 ITH1 39.2k VOUT2 1.8V 4A 20k VFB2 10k 0.01F RS2 0.006 COUT2 100F x2 PGND 31.6k 100k L2 1.2H DB2 2.2 COUT1 100F x2 20 0.1F RT SGND RUN1 0.01F 100pF ITH2 DTR1 VRNG1 CIN1: SUN CON 35HVP47M CIN2: TAIYO YUDEN GMK325BJ106MN-T COUT1,COUT2: MURATA GRM31CR60J107ME39L COUT2, COUT4: SANYO 4TPC150M DB1, DB2: CENTRAL SEMI CMDSH-4ETR L1, L2: COILCRAFT XAL5030-122MEB M1, M2: SILICONIX SI4816DY 100k PGOOD2 61.9k DTR2 VRNG2 3838 TA02 PHASMD MODE/PLLIN CLKOUT RUN2 Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3838-1/ LTC3838-2 Dual or Single Output, Controlled On-Time, Synchronous StepDown Controller, Differential VOUT Sense, Internal/External VREF PLL, 200kHz to 2MHz Operating Frequency, 4.5V VIN 38V, 0.6V/0.4V VOUT 5.5V, 5mm x 7mm QFN-38, TSSOP-38 (Table 1) LTC3839 Single Output, 2-Phase, Controlled On-Time, Synchronous Step- PLL, 200kHz to 2MHz Operating Frequency, 4.5V VIN 38V, 0.6V VOUT 5.5V, 5mm x 5mm QFN-32 Down Controller with Differential VOUT Sense (R) 4.5V VIN 15V, 0.6V VOUT 14V 16mm x 16mm x 5mm Package Dual 25A or Single 50A DC/DC Module Regulator with Multiphase Operation and Differential VOUT Sense LTM4650 LTM4630A Dual 18A or Single 36A DC/DC Module Regulator with Multiphase Operation and Differential VOUT Sense 4.5V VIN 15V, 0.6V VOUT 5.3V 16mm x 16mm x 4.41mm Package LTC7851/ LTC7851-1 Quad Output, Multiphase Step-Down Voltage Mode DC/DC Controller with Accurate Current Sharing Operates with DrMOS, Power Blocks or External Drivers/MOSFETs, 3V VIN 27V LTC3774 Dual, Multiphase Current Mode Synchronous Step-Down Controller with Sub-Milliohm DCR Sensing, Up to 12 Phases Operates with DrMOS, Power Blocks or External Drivers/MOSFETs, 4.5V VIN 38V, 0.6V VOUT 3.5V with Remote VOUT Sense LTC3855 Dual, Multiphase, Synchronous Step-Down DC/DC Controller with Diff Amp and DCR Temperature Compensation Phase-Lockable Fixed Frequency 250kHz to 770kHz, 4.5V VIN 38V, 0.8V VOUT 12V LTC3869/ LTC3869-2 Dual Output, 2-Phase Synchronous Step-Down DC/DC Controller, with Accurate Current Share 4V VIN 38V, VOUT3 Up to 12.5V PLL Fixed 250kHz to 750kHz Frequency LTC3861/ LTC3861-1 Dual, Multiphase Synchronous Step-Down DC/DC Controller with Multiphase Operation and Differential VOUT Sense Operates with Power Blocks, DR MOS or External Drivers/MOSFETs 3V VIN 24V, 5mm x 6mm QFN-36 3838fb 54 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC3838 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTC3838 LT 0316 REV B * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2011