Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. Motion-SPM FSB50250AB TM Smart Power Module (SPM(R)) Features Applications * 500V RDS(on)=3.8W(max) 3-phase FRFET inverter including high voltage integrated circuit (HVIC) * Three-phase inverter driver for small power ac motor drives General Description * 3 divided negative dc-link terminals for inverter current sensing applications FSB50250AB is a tiny smart power module (SPM(R)) based on FRFET technology as a compact inverter solution for small power motor drive applications such as fan motors and water suppliers. It is composed of 6 fast-recovery MOSFET (FRFET), and 3 half-bridge HVICs for FRFET gate driving. FSB50250AB provides low electromagnetic interference (EMI) characteristics with optimized switching speed. Moreover, since it employs FRFET as a power switch, it has much better ruggedness and larger safe operation area (SOA) than that of an IGBT-based power module or one-chip solution. The package is optimized for the thermal performance and compactness for the use in the built-in motor application and any other application where the assembly space is concerned. FSB50250AB is the best solution for the compact inverter providing the energy efficiency, compactness, and low electromagnetic interference. * HVIC for gate driving and undervoltage protection * 3/5V CMOS/TTL compatible, active-high interface * Optimized for low electromagnetic interference * Isolation voltage rating of 1500Vrms for 1min. * HVIC temperature sensing * Embedded bootstrap diode in the package * RoHS compliant (c)2011 Fairchild Semiconductor Corporation FSB50250AB Rev. A 1 www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) January 2012 Inverter Part (Each FRFET Unless Otherwise Specified) Symbol Parameter Conditions Rating Units 500 V VPN DC Link Input Voltage, Drain-source Voltage of each FRFET *ID25 Each FRFET Drain Current, Continuous TC = 25C 1.2 A *ID80 Each FRFET Drain Current, Continuous TC = 80C 0.9 A *IDP Each FRFET Drain Current, Peak TC = 25C, PW < 100ms 3.1 A *IDRMS Each FRFET Drain Current, Rms TC = 80C, FPWM < 20KHz Maximum Power Dissipation TC = 25C, For Each FRFET *P D 0.6 Arms 13.4 W Rating Units Control Part (Each HVIC Unless Otherwise Specified) Symbol Parameter Conditions VCC Control Supply Voltage Applied between VCC and COM 20 V VBS High-side Bias Voltage Applied between VB and V S 20 V VIN Input Signal Voltage Applied between IN and COM -0.3 ~ VCC+0.3 V Rating Units 500 V Bootstrap Diode Part (Each Bootstrap diode Unless Otherwise Specified) Symbol VRRMB Parameter Conditions Maixmum Repetitive Reverse Voltage * IFB Forward Current TC = 25C 0.5 A * IFPB Forward Current (Peak) TC = 25C, Under 1ms Pulse Width 1.5 A Conditions Rating Units Each FRFET under inverter operating condition (Note 1) 9.3 C/W Conditions Rating Units Operating Junction Temperature -40 ~ 150 C TSTG Storage Temperature -40 ~ 125 C VISO Isolation Voltage 1500 Vrms Thermal Resistance Symbol RqJC Parameter Junction to Case Thermal Resistance Total System Symbol TJ Parameter 60Hz, Sinusoidal, 1 minute, Connection pins to heatsink Note: 1. For the measurement point of case temperature TC, please refer to Figure 4. 2. Marking " * " is calculation value or design factor. 2 FSB50250AB Rev. A www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) Absolute Maximum Ratings FSB50250AB Smart Power Module (SPM(R)) Pin descriptions Pin Number Pin Name Pin Description 1 COM IC Common Supply Ground 2 VB(U) Bias Voltage for U Phase High Side FRFET Driving 3 VCC(U) Bias Voltage for U Phase IC and Low Side FRFET Driving 4 IN(UH) Signal Input for U Phase High-side 5 IN(UL) Signal Input for U Phase Low-side 6 N.C 7 VB(V) N.C 8 VCC(V) Bias Voltage for V Phase IC and Low Side FRFET Driving 9 IN (VH) Signal Input for V Phase High-side 10 IN (VL) Signal Input for V Phase Low-side 11 N.C Bias Voltage for V Phase High Side FRFET Driving N.C 12 VB(W) 13 VCC(W) Bias Voltage for W Phase IC and Low Side FRFET Driving 14 IN(WH) Signal Input for W Phase High-side 15 IN(WL) Signal Input for W Phase Low-side 16 Vts 17 P 18 U, VS(U) 19 NU Negative DC-Link Input for U Phase 20 NV Negative DC-Link Input for V Phase 21 V, VS(V) 22 NW 23 W, VS(W) Bias Voltage for W Phase High Side FRFET Driving Output for HVIC temperature sensing Positive DC-Link Input Output for U Phase & Bias Voltage Ground for High Side FRFET Driving Output for V Phase & Bias Voltage Ground for High Side FRFET Driving Negative DC-Link Input for W Phase Output for W Phase & Bias Voltage Ground for High Side FRFET Driving (1) COM (2) V B(U) (17) P (3) V CC(U) VCC VB (4) IN (UH) HIN HO (5) IN (UL) LIN VS COM LO (18) U, V S(U) (6) N.C (19) N U (7) V B(V) (8) V CC(V) VCC VB (9) IN (VH) HIN HO (10) IN (VL) LIN VS COM LO (20) N V (21) V, VS(V) (11) N.C (12) V B(W) (13) V CC(W) VCC VB (14) IN (WH) HIN HO (15) IN (WL) LIN VS COM LO (16) Vts (22) N W (23) W, V S(W) Vts Note: Source terminal of each low-side MOSFET is not connected to supply ground or bias voltage ground inside SPM(R). External connections should be made as indicated in Figure 3 Figure 1. Pin Configuration and Internal Block Diagram (Bottom View) 3 FSB50250AB Rev. A www.fairchildsemi.com Inverter Part (Each FRFET Unless Otherwise Specified) Symbol BVDSS Parameter Conditions Drain-Source Breakdown VIN= 0V, ID = 1mA (Note 1) Voltage Min Typ Max Units 500 - - V IDSS Zero Gate Voltage Drain Current VIN= 0V, VDS = 500V - - 1 mA RDS(on) Static Drain-Source On-Resistance VCC = VBS = 15V, VIN = 5V, ID = 0.5A - 2.5 3.8 W VSD Drain-Source Diode Forward Voltage VCC = VBS = 15V, VIN = 0V, ID = -0.5A - - 1.2 V - 1150 - ns - 950 - ns Switching Times VPN = 300V, VCC = VBS = 15V, ID = 0.5A VIN = 0V 5V, Inductive load L=3mH High- and low-side FRFET switching (Note 2) - 190 - ns - 40 - mJ - 10 - mJ tON tOFF trr EON EOFF RBSOA V = 400V, VCC = V BS = 15V, ID = IDP, V DS=BVDSS, Reverse-bias Safe Oper- PN TJ = 150C ating Area High- and low-side FRFET switching (Note 3) Full Square Control Part (Each HVIC Unless Otherwise Specified) Symbol IQCC Parameter Quiescent VCC Current Conditions Min Typ Max Units VCC=15V, VIN=0V Applied between VCC and COM - - 200 mA Applied between VB(U)-U, VB(V)-V, VB(W)-W - - 100 mA IQBS Quiescent VBS Current VBS=15V, VIN=0V UVCCD Low-side Undervoltage Protection (Figure 8) VCC Undervoltage Protection Detection Level 7.4 8.0 9.4 V VCC Undervoltage Protection Reset Level 8.0 8.9 9.8 V High-side Undervoltage Protection (Figure 9) VBS Undervoltage Protection Detection Level 7.4 8.0 9.4 V VBS Undervoltage Protection Reset Level 8.0 8.9 9.8 V 980 mV UVCCR UVBSD UVBSR Vts HVIC Temperature sensing voltage output VCC=15V, THVIC=25C(Note 4) 600 790 VIH ON Threshold Voltage Logic High Level 2.9 - - V VIL OFF Threshold Voltage Logic Low Level - - 0.8 V Applied between IN and COM Bootstrap Diode Part (Each Bootstrap diode Unless Otherwise Specified) Symbol Parameter Conditions Min Typ Max Units VFB Forward Voltage IF = 0.1A, TC = 25C(Note 5) - 2.5 - V trrB Reverse Recovery Time IF = 0.1A, TC = 25C - 80 - ns Note: 1. BVDSS is the absolute maximum voltage rating between drain and source terminal of each FRFET inside SPM(R). VPN should be sufficiently less than this value considering the effect of the stray inductance so that VDS should not exceed BVDSS in any case. 2. tON and tOFF include the propagation delay time of the internal drive IC. Listed values are measured at the laboratory test condition, and they can be different according to the field applcations due to the effect of different printed circuit boards and wirings. Please see Figure 6 for the switching time definition with the switching test circuit of Figure 7. 3. The peak current and voltage of each FRFET during the switching operation should be included in the safe operating area (SOA). Please see Figure 7 for the RBSOA test circuit that is same as the switching test circuit. 4. Vts is only for sensing temperature of module and cannot shutdown MOSFETs automatically. 5. Built in bootstrap diode includes around 15 resistance characteristic. Please refer to Figure 2. 4 FSB50250AB Rev. A www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) Electrical Characteristics (TJ = 25C, VCC=VBS=15V Unless Otherwise Specified) Symbol Parameter Value Conditions Min. Typ. Units Max. VPN Supply Voltage Applied between P and N - 300 400 V VCC Control Supply Voltage Applied between VCC and COM 13.5 15 16.5 V VBS High-side Bias Voltage Applied between VB and VS 13.5 15 16.5 V 3.0 - VCC V 0 - 0.6 V 1.0 - - ms - 15 - kHz VIN(ON) Input ON Threshold Voltage VIN(OFF) Input OFF Threshold Voltage Applied between IN and COM tdead Blanking Time for Preventing VCC =VBS=13.5 ~ 16.5V, TJ 150C Arm-short fPWM PWM Switching Frequency TJ 150C Package Marking & Ordering Information Device Marking Device Package Reel Size Packing Type Quantity FSB50250AB FSB50250AB SPM23DD-21L - - 15 Built in Bootstrap Diode VF-IF Characteristic 1.0 0.9 0.8 0.7 IF [A] 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0 1 2 3 4 5 6 7 8 VF [V] 9 10 11 12 13 14 15 Tc=25C Figure 2. Built in Bootstrap Diode Characteristics(typ.) 5 FSB50250AB Rev. A www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) Recommended Operating Condition 15V Line C1 * Example circuit : W phase VDC P Micom R5 C5 VCC VB HIN HO LIN VS COM LO V C2 10mF C4 LIN Output Note 0 0 Z Both FRFET Off 0 1 0 Low side FRFET On C3 1 0 VDC High side FRFET On 1 1 Forbidden Shoot through Open Open Z Same as (0,0) R3 N Vts HIN Inverter Output One Leg Diagram of SPM * Example of bootstrap paramters : C1 = C2 =1mF ceramic capacitor Note: 1. Parameters for bootsrap circuit elements are dependent on PWM algorithm. For 15 kHz of switching frequency, typical example of parameters is shown above. 2. RC coupling(R5 and C 5) and C 4 at each input of SPM(R) and Micom (indicated as dotted lines) may be used to prevent improper signal due to surge noise. Signal input of SPM(R) is compatible with standard CMOS or LSTTL outputs. 3. Bold lines should be short and thick in PCB pattern to have small stray inductance of circuit, which results in the reduction of surge voltage. Bypass capacitors such as C1, C2 and C3 should have good high-frequencycharacteristics to absorb high-frequency ripple current. Figure 3. Recommended CPU Interface and Bootstrap Circuit with Parameters Note: Attach the thermocouple on top of the heatsink-side of SPM(R) (between SPM(R) and heatsink if applied) to get the correct temperature measurement. Figure 4. Case Temperature Measurement 3.5 3.0 VTS [V] 2.5 2.0 1.5 1.0 0.5 20 40 60 80 100 120 140 160 THVIC [deg] Figure 5. Temperature profile of Vts(typ.) 6 FSB50250AB Rev. A www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) These values depend on PWM control algorithm FSB50250AB Smart Power Module (SPM(R)) VIN VIN Irr 120% of ID 100% of ID VDS ID 10% of ID ID VDS tON trr tOFF (a) Turn-on (b) Turn-off Figure 6. Switching Time Definition C BS VCC ID VCC VB HIN HO LIN VS COM LO L VDC + V DS - Vts One-leg Diagram of SPM Figure 7. Switching and RBSOA(Single-pulse) Test Circuit (Low-side) Input Signal UV Protection Status Low-side Supply, VCC RESET DETECTION RESET UVCCR UVCCD MOSFET Current Figure 8. Undervoltage Protection (Low-side) Input Signal UV Protection Status High-side Supply, VBS RESET DETECTION RESET UVBSR UVBSD MOSFET Current Figure 9. Undervoltage Protection (High-side) 7 FSB50250AB Rev. A www.fairchildsemi.com (2 ) VB(U) (3 ) VCC(U) R5 (4 ) IN(UH) (5 ) IN(UL) C5 C2 (6 ) N.C (17) P VCC VB HIN HO LIN VS COM LO (18 ) U , VS(U) C3 (19) NU (7 ) VB(V) (8 ) VCC(V) (9 ) IN(VH) Micom (10) IN(VL) VDC VCC VB HIN HO LIN VS COM LO VCC VB HIN HO LIN VS COM LO (20) NV (21 ) V , VS(V) M (11) N.C (12) VB(W) (13) VCC(W) (14) IN(WH) (15) IN(WL) (16 ) VTS (22) NW (23) W , VS(W) VTS C4 For current sensing and protection 15- V Supply R4 C6 R3 Note: 1. About pin position, refer to Figure 2. 2. RC coupling(R5 and C5, R4 and C 6) and C 4 at each input of SPM(R) and Micom are useful to prevent improper input signal caused by surge noise. 3. The voltage drop across R3 affects the low side switching performance and the bootstrap characteristics since it is placed between COM and the source terminal of the low side MOSFET. For this reason, the voltage drop across R3 should be less than 1V in the steady-state. 4. Ground wires and output terminals, should be thick and short in order to avoid surge voltage and malfunction of HVIC. 5. All the filter capacitors shoud be connected close to SPM(R), and they should have good characteristics for rejecting high-frequency ripple current. Figure 10. Example of Application Circuit 8 FSB50250AB Rev. A www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) C1 (1 ) COM FSB50250AB Smart Power Module (SPM(R)) Detailed Package Outline Drawings Dimension unit : [mm] 9 FSB50250AB Rev. A www.fairchildsemi.com FRFET(R) Global Power ResourceSM Green FPSTM Green FPSTM e-SeriesTM GTOTM IntelliMAXTM ISOPLANARTM MegaBuckTM MICROCOUPLERTM MicroFETTM MicroPakTM MillerDriveTM MotionMaxTM Motion-SPMTM OPTOLOGIC(R) OPTOPLANAR(R) Build it NowTM CorePLUSTM CorePOWERTM CROSSVOLTTM CTLTM Current Transfer LogicTM EcoSPARK(R) EfficentMaxTM EZSWITCHTM * TM (R) Fairchild (R) Fairchild Semiconductor(R) FACT Quiet SeriesTM FACT(R) FAST(R) FastvCoreTM FlashWriter(R) * FPSTM F-PFSTM Programmable Active DroopTM QFET(R) QSTM Quiet SeriesTM RapidConfigureTM TM Saving our world, 1mW /W /kW at a timeTM SmartMaxTM SMART STARTTM SPM(R) STEALTHTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SupreMOSTM SyncFETTM (R) (R) PDP SPMTM Power-SPMTM PowerTrench(R) PowerXSTM TinyBoostTM TinyBuckTM TinyLogic(R) TINYOPTOTM TinyPowerTM TinyPWMTM TinyWireTM TriFault DetectTM mSerDesTM UHC(R) Ultra FRFETTM UniFETTM VCXTM VisualMaxTM XSTM The Power Franchise(R) * EZSWITCHTM and FlashWriter(R) are trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.Fairchildsemi.com, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufactures of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed application, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handing and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address and warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative / In Design Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Obsolete Not In Production Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only. Rev. I38 10 FSB50250AB Rev. A www.fairchildsemi.com FSB50250AB Smart Power Module (SPM(R)) TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com