LTC4361-1/LTC4361-2 Overvoltage/Overcurrent Protection Controller Features n n n n n n n n n n n n n Description 2.5V to 5.5V Operation Overvoltage Protection Up to 80V No Input Capacitor or TVS Required for Most Applications 2% Accurate 5.8V Overvoltage Threshold 10% Accurate 50mV Overcurrent Circuit Breaker <1s Overvoltage Turn-Off, Gentle Shutdown Controls N-Channel MOSFET Adjustable Power-Up dV/dt Limits Inrush Current Reverse Voltage Protection Power Good Output Low Current Shutdown Latchoff (LTC4361-1) or Auto-Retry (LTC4361-2) After Overcurrent Available in 8-Lead ThinSOTTM and 8-Lead (2mm x 2mm) DFN Packages Applications n n n n n USB Protection Handheld Computers Cell/Smart Phones MP3/MP4 Players Digital Cameras The LTC(R)4361 overvoltage/overcurrent protection controller safeguards 2.5V to 5.5V systems from input supply overvoltage. It is designed for portable devices with multiple power supply options including wall adaptors, car battery adaptors and USB ports. The LTC4361 controls an external N-channel MOSFET in series with the input power supply. During overvoltage transients, the LTC4361 turns off the MOSFET within 1s, isolating downstream components from the input supply. Inductive cable transients are absorbed by the MOSFET and load capacitance. In most applications, the LTC4361 provides protection from transients up to 80V without requiring transient voltage suppressors or other external components. The LTC4361 has a delayed start-up and adjustable dV/dt ramp-up for inrush current limiting. A PWRGD pin provides power good monitoring for VIN. The LTC4361 features a soft shutdown controlled by the ON pin and drives an optional external P-channel MOSFET for negative voltage protection. Following an overvoltage condition, the LTC4361 automatically restarts with a start-up delay. After an overcurrent fault, the LTC4361-1 remains off while the LTC4361-2 automatically restarts after a 130ms start-up delay. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and ThinSOT, Hot Swap, No RSENSE and PowerPath are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application Protection from Overvoltage and Overcurrent VIN 5V 0.025 Si1470DH COUT Output Protected from Overvoltage at Input VOUT 5V 1.5A VIN GATE SENSE OUT IN LTC4361 ON PWRGD GND VOUT VIN, VOUT 5V/DIV 436112 TA01a VGATE 10V/DIV Si1470DH COUT = 10F 0.5s/DIV 436112 TA01b 436112fb 1 LTC4361-1/LTC4361-2 Absolute Maximum Ratings (Notes 1, 2) Bias Supply Voltage (IN)............................. -0.3V to 85V Input Voltages SENSE.................................................... -0.3V to 85V OUT, ON.................................................... -0.3V to 9V Output Voltages PWRGD..................................................... -0.3V to 9V GATE (Note 3)......................................... -0.3V to 15V GATEP..................................................... -0.3V to 85V IN to GATEP............................................ -0.3V to 10V Operating Temperature Range LTC4361C................................................. 0C to 70C LTC4361I..............................................-40C to 85C LTC4361H........................................... -40C to 125C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec) TSOT.................................................................. 300C Pin Configuration TOP VIEW TOP VIEW ON 1 OUT 2 GATEP 3 GND 4 8 IN GND 1 8 PWRGD 7 GATE 6 SENSE 5 IN GATEP 2 OUT 3 9 ON 4 TS8 PACKAGE 8-LEAD PLASTIC TSOT-23 7 SENSE 6 GATE 5 PWRGD DC PACKAGE 8-LEAD (2mm x 2mm) PLASTIC DFN TJMAX = 125C, JA = 195C/W TJMAX = 125C, JA = 102C/W EXPOSED PAD (PIN 9) IS GND, CONNECTION OPTIONAL Order Information Lead Free Finish TAPE AND REEL (MINI) TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4361CTS8-1#TRMPBF LTC4361CTS8-1#TRPBF LTDWN 8-Lead Plastic TSOT-23 0C to 70C LTC4361CTS8-2#TRMPBF LTC4361CTS8-2#TRPBF LTFMN 8-Lead Plastic TSOT-23 0C to 70C LTC4361ITS8-1#TRMPBF LTC4361ITS8-1#TRPBF LTDWN 8-Lead Plastic TSOT-23 -40C to 85C LTC4361ITS8-2#TRMPBF LTC4361ITS8-2#TRPBF LTFMN 8-Lead Plastic TSOT-23 -40C to 85C LTC4361HTS8-1#TRMPBF LTC4361HTS8-1#TRPBF LTDWN 8-Lead Plastic TSOT-23 -40C to 125C LTC4361HTS8-2#TRMPBF LTC4361HTS8-2#TRPBF LTFMN 8-Lead Plastic TSOT-23 -40C to 125C LTC4361CDC-1#TRMPBF LTC4361CDC-1#TRPBF LDWP 8-Lead (2mm x 2mm) Plastic DFN 0C to 70C LTC4361CDC-2#TRMPBF LTC4361CDC-2#TRPBF LFMP 8-Lead (2mm x 2mm) Plastic DFN 0C to 70C LTC4361IDC-1#TRMPBF LTC4361IDC-1#TRPBF LDWP 8-Lead (2mm x 2mm) Plastic DFN -40C to 85C LTC4361IDC-2#TRMPBF LTC4361IDC-2#TRPBF LFMP 8-Lead (2mm x 2mm) Plastic DFN -40C to 85C LTC4361HDC-1#TRMPBF LTC4361HDC-1#TRPBF LDWP 8-Lead (2mm x 2mm) Plastic DFN -40C to 125C LTC4361HDC-2#TRMPBF LTC4361HDC-2#TRPBF LFMP 8-Lead (2mm x 2mm) Plastic DFN -40C to 125C TRM = 500 pieces. *Temperature grades are identified by a label on the shipping container. Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 436112fb 2 LTC4361-1/LTC4361-2 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VIN = 5V, VON = 0V, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 80 V 2.1 2.47 V Supplies VIN Input Voltage Range l 2.5 VIN(UVL) Input Undervoltage Lockout VIN Rising l 1.8 IIN Input Supply Current VON = 0V l 220 400 A VON = 2.5V l 1.5 10 A Thresholds VIN(OV) IN Pin Overvoltage Threshold VIN Rising l 5.684 5.8 5.916 V VIN(OVL) IN Pin Overvoltage Recovery Threshold VIN Falling l 5.51 5.7 5.85 V VOV Overvoltage Hysteresis l 25 100 260 mV VOC Overcurrent Threshold VIN - VSENSE l 45 50 55 mV 2.5V VIN < 3V, IGATE = -1A 3V VIN < 5.5V, IGATE = -1A l l 3.5 4.5 4.5 6 6 7.9 V V External Gate Drive VGATE External N-Channel MOSFET Gate Drive (VGATE - VOUT) VGATE(TH) GATE High Threshold for PWRGD Status VIN = 3.3V VIN = 5V l l 5.7 6.7 6.3 7.2 6.8 7.8 V V IGATE(UP) GATE Pull-Up Current VGATE = 1V l -4.5 -10 -15 A VGATE(UP) GATE Ramp-Up VGATE = 1V to 7V l 1.3 3 4.5 V/ms IGATE(FST) GATE Pull-Down Current Fast Turn-Off, VIN = 6V, VGATE = 9V (C-, I-Grade) (H-Grade) l l 15 12 30 30 60 60 mA mA IGATE(DN) GATE Pull-Down Current VON = 2.5V, VGATE = 9V l 5 40 80 A l l 5 l 0.4 Input Pins ISENSE(IN) SENSE Input Current VSENSE = 5V IOUT(IN) OUT Input Current VOUT = 5V, VON = 0V VOUT = 5V, VON = 2.5V 10 VON(TH) ON Input Threshold ION ON Pull-Down Current VON = 2.5V l 2 VGATEP(CLP) IN to GATEP Clamp Voltage VIN = 8V to 80V l 5 l 0.6 10 0 nA 20 3 A A 1.5 V 5 10 A 5.8 7.9 V Output Pins RGATEP GATEP Resistive Pull-Down VGATEP = 3V VPWRGD(OL) PWRGD Output Low Voltage VIN = 5V, IPWRGD = 3mA 2 3.2 M 0.23 0.23 0.4 0.5 V V RPWRGD PWRGD Pull-Up Resistance to OUT VIN = 6.5V, VPWRGD = 1V l 220 500 800 k tON GATE On Delay VIN High to IGATE = -5A l 50 130 219 ms tOFF GATE Off Propagation Delay VIN = Step 5V to 6.5V to PWRGD High VIN - VSENSE = Step 0mV to 100mV l l 5 0.25 10 1 20 s s tPWRGD PWRGD Delay VIN = Step 5V to 6.5V VGATE > VGATE(TH) to PWRGD Low l l 25 0.25 65 1 105 s ms tON(OFF) ON High to GATE Off VON = Step 0V to 2.5V l 2 5 s (C-, I-Grade) (H-Grade) l l Delay Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to GND unless otherwise specified. Note 3: An internal clamp limits VGATE to a minimum of 4.5V above VOUT. Driving this pin to voltages beyond this clamp may damage the device. 436112fb 3 LTC4361-1/LTC4361-2 Typical Performance Characteristics TA = 25C, VIN = 5V, VON = 0V, unless otherwise noted. Input Supply Current vs Input Voltage GATE Fast Pull-Down Current vs Temperature GATE Drive vs GATE Current 40 8 10000 7 6 100 VGATE (V) IIN (A) VON = 0V VON = 2.5V 10 5 VIN = 3V 4 3 VIN = 2.5V 2 1 35 VIN = 5V IGATE(FST) (mA) 1000 VIN = 6V VGATE = 9V 30 25 1 0.1 10 VIN (V) 1 0 100 0 2 4 6 8 10 500 8 GATE Voltage and GATE High Threshold (for PWRGD Status) vs Input Voltage 11 6 10 VGATE /VGGATE(TH) (V) 7 4 3 2 100 1 1 2 3 IPWRGD (mA) 4 5 12 VIN = STEP 5V TO (VIN(OV) + VOVDRV) 5 tOFF (s) VPWRGD(OL) (mV) 400 200 0 VGATE 9 8 VGATE(TH) 7 6 0 0.5 1 1.5 VOVDRV (V) 2 2.5 4 2.5 3 3.5 4 4.5 VIN (V) 436112 G05 Normal Start-Up Sequence 5 5.5 6 436112 G06 GATE Slow Ramp-Up Entering Sleep Mode VON 5V/DIV VIN 5V/DIV VOUT 5V/DIV VIN 5V/DIV VOUT 5V/DIV VGATE 10V/DIV VGATE 10V/DIV VGATE 10V/DIV ICABLE 0.5A/DIV ICABLE 0.5A/DIV ICABLE 0.5A/DIV 436112 G07 VIN = VOUT 5 436112 G04 20ms/DIV FIGURE 5 CIRCUIT RIN = 150m, LIN = 0.7H RSENSE = 25m LOAD = 10, COUT = 10F 125 436112 G03 GATE Off Propagation Delay vs Overdrive 300 100 436112 G02 PWRGD Voltage vs PWRGD Current 0 50 75 0 25 TEMPERATURE (C) -25 IGATE (A) 436112 G01 0 20 -50 12 VOUT 5V/DIV 1ms/DIV FIGURE 5 CIRCUIT RIN = 150m, LIN = 0.7H RSENSE = 25m LOAD = 10, COUT = 10F 436112 G08 50s/DIV FIGURE 5 CIRCUIT RIN = 150m, LIN = 0.7H RSENSE = 25m LOAD = 10, COUT = 10F 436112 G09 436112fb 4 LTC4361-1/LTC4361-2 Pin Functions Exposed Pad (DFN): Ground. Connection to PCB is optional. GATE: Gate Drive for External N-Channel MOSFET. An internal charge pump provides a 10A pull-up current to charge the gate of the external N-channel MOSFET. An additional ramp circuit limits the GATE ramp rate when turning on to 3V/ms. For slower ramp rates, connect an external capacitor from GATE to GND. An internal clamp limits GATE to 6V above the OUT pin voltage. An internal GATE high comparator controls the PWRGD pin. GATEP: Gate Drive for External P-Channel MOSFET. GATEP connects to the gate of an optional external P-channel MOSFET to protect against negative voltages at IN. This pin is internally clamped to 5.8V below VIN. An internal 2M resistor connects this pin to ground. Connect to IN if not used. GND: Device Ground. IN: Supply Voltage Input. Connect this pin to the input power supply. This pin has an overvoltage threshold of 5.8V. After an overvoltage event, this pin must fall below VIN(OV) - VOV to release the overvoltage lockout. During lockout, GATE is held low and the PWRGD pull-down releases. ON: On Control Input. A logic low at ON enables the LTC4361. A logic high at ON activates a low current pull-down at the GATE pin and causes the LTC4361 to enter a low current sleep mode. An internal 5A current pulls ON down to ground. Connect to ground or leave open if unused. OUT: Output Voltage Sense Input for GATE Clamp. Connect to the source of the external N-channel MOSFET to sense the output voltage for GATE to OUT clamp. PWRGD: Power Good Status. Open-drain output with internal 500k resistive pull-up to OUT. Pulls low 65ms after GATE ramps above VGATE(TH). SENSE: Current Sense Input. Connect a sense resistor between IN and SENSE. An overcurrent protection circuit turns off the N-channel MOSFET when the voltage across the sense resistor exceeds 50mV for more than 10s. 436112fb 5 LTC4361-1/LTC4361-2 Block Diagram GATEP IN CHARGE PUMP 1.8M 10A GATE HIGH COMPARATOR + - 5A OVERCURRENT COMPARATOR + - - CONTROL OUT VGATE(TH) + + 1V GATE 5.8V OVERVOLTAGE COMPARATOR 50mV - ON SENSE 5.8V 200k 500k + - 5.8V 5.7V PWRGD GND 436112 BD Operation Mobile devices like cell phones and MP3/MP4 players have highly integrated subsystems fabricated from deep submicron CMOS processes. The small form factor is accompanied by low absolute maximum voltage ratings. The sensitive electronics are susceptible to damage from transient or DC overvoltage conditions from the power supply. Failures or faults in the power adaptor can cause an overvoltage event. So can hot-plugging an AC adaptor into the power input of the mobile device (see LTC Application Note 88). Today's mobile devices derive their power supply or recharge their internal batteries from multiple alternative inputs like AC wall adaptors, car battery adaptors and USB ports. A user may unknowingly plug in the wrong adaptor, damaging the device with a high or even a negative power supply voltage. The LTC4361 protects low voltage electronics from these overvoltage conditions by controlling a low cost external Nchannel MOSFET configured as a pass transistor. At power-up (VIN > 2.1V), a start-up delay cycle begins. Any overvoltage condition causes the delay cycle to continue until a safe voltage is present. When the delay cycle completes, an internal high side switch driver slowly ramps up the MOSFET gate, powering up the output at a controlled rate and limiting the inrush current to the output capacitor. If the voltage at the IN pin exceeds 5.8V (VIN(OV)), GATE is pulled low quickly to protect the load. The incoming power supply must remain below 5.7V (VIN(OV) - VOV) for the duration of the start-up delay to restart the GATE ramp-up. A sense resistor placed between IN and SENSE implements an overcurrent protection with a 50mV trip threshold and a 10s glitch filter. After an overcurrent, the LTC43611 latches off while the LTC4361-2 restarts following a 130ms delay. The LTC4361 has a CMOS compatible ON input. When driven low, the part is enabled. When driven high, the external N-channel MOSFET is turned off and the supply current of the LTC4361 drops to 1.5A. The PWRGD pulldown releases during this low current sleep mode, UVLO, overvoltage or overcurrent and the subsequent 130ms start-up delay. After the start-up delay, GATE starts its slow ramp-up and ramps higher than VGATE(TH) to trigger a 65ms delay cycle. When that completes, PWRGD pulls low.The LTC4361 has a GATEP pin that drives an optional external P-channel MOSFET to provide protection against negative voltages at IN. 436112fb 6 LTC4361-1/LTC4361-2 Applications Information The typical LTC4361 application protects 2.5V to 5.5V systems in portable devices from power supply overvoltage. The basic application circuit is shown in Figure 1. Device operation and external component selection is discussed in detail in the following sections. VIN 5V M1 Si1470DH RSENSE 0.025 COUT 10F VOUT 5V 1.5A GATE SENSE OUT LTC4361 IN ON PWRGD GND 436112 F01 Figure 1. Protection from Input Overvoltage and Overcurrent Start-Up When VIN is less than the undervoltage lockout level of 2.1V, the GATE driver is held low and the PWRGD pull-down is high impedance. When VIN rises above 2.1V and ON is held low, a 130ms delay cycle starts. Any undervoltage or overvoltage event at IN (VIN < 2.1V or VIN > 5.7V) restarts the delay cycle. This delay allows the N-channel MOSFET to isolate the output from any input transients that occur at start-up. When the delay cycle completes, GATE starts its slow ramp-up. GATE Control An internal charge pump provides a gate overdrive greater than 3.5V when 2.5V VIN < 3V. If VIN 3V, the gate drive is guaranteed to be greater than 4.5V. This allows the use of logic-level N-channel MOSFETs. An internal 6V clamp between GATE and OUT protects the MOSFET gate. The GATE ramp rate is limited to 3V/ms. VOUT follows at a similar rate which results in an inrush current into the load capacitor COUT of: IINRUSH = COUT * dVGATE = COUT * 3 [mA/F ] dt The servo loop is compensated by the parasitic capacitance of the external MOSFET. No further compensation components are normally required. In the case where the parasitic capacitance is less than 100pF, a 100pF compensation capacitor between GATE and ground may be required. An even slower GATE ramp and lower inrush current can be achieved by connecting an external capacitor, CG, from GATE to ground. The voltage at GATE then ramps up with a slope equal to 10A/CG [V/s]. Choose CG using the formula: CG = 10A IINRUSH * COUT Overvoltage When power is first applied, VIN must remain below 5.7V (VIN(OV) - VOV) for more than 130ms before GATE is ramped up to turn on the MOSFET. If VIN then rises above 5.8V (VIN(OV)), the overvoltage comparator activates the 30mA fast pull-down on GATE within 1s. After an overvoltage condition, the MOSFET is held off until VIN once again remains below 5.7V for 130ms. Overcurrent The overcurrent comparator protects the MOSFET from excessive current. It trips when the SENSE pin falls more than 50mV below IN for 10s. When the overcurrent comparator trips, GATE is pulled low quickly and the PWRGD pull-down releases. The LTC43612 automatically tries to apply power again after a 130ms start-up delay. 436112fb 7 LTC4361-1/LTC4361-2 APPLICATIONS INFORMATION The LTC4361-1 has an internal latch that maintains this off state until it is reset. To reset this latch, cycle IN below 2.1V (VIN(UVL)) or ON above 1.5V (VON(TH)) for more than 500s. After reset, the LTC4361-1 goes through the start-up cycle. In applications not requiring the overcurrent protection, tie the SENSE pin to the IN pin. To implement an overcurrent threshold ITRIP , choose RSENSE using the formula: RSENSE = VOC I TRIP After choosing the RSENSE, keep in mind that: ITRIP(MAX) = ITRIP(MIN) = VOC(MAX) RSENSE(MIN) VOC(MIN) PWRGD Output PWRGD is an active low output with a MOSFET pull-down to ground and a 500k resistive pull-up to OUT. The PWRGD pin pull-down releases during the low current sleep mode (invoked by ON high), UVLO, overvoltage or overcurrent and the subsequent 130ms start-up delay. After the startup delay, GATE starts its slow ramp-up and control of the PWRGD pull-down passes on to the GATE high comparator. VGATE > VGATE(TH) for more than 65ms asserts the PWRGD pull-down and VGATE < VGATE(TH) releases the pull-down. The PWRGD pull-down is capable of sinking up to 3mA of current allowing it to drive an optional LED. To interface PWRGD to another I/O rail, connect a resistor from PWRGD to the I/O rail with a resistance low enough to override the internal 500k pull-up to OUT. Figure 2 details PWRGD behavior for a LTC4361-2 with 1k pull-up to 5V at PWRGD. RSENSE(MAX) START-UP FROM UVLO OV RESTART FROM OV ON OC RESTART FROM ON RESTART FROM OC OC THRESHOLD ICABLE IN VIN(OV) VIN(OV)-VOV VIN(UVL) OUT VGATE(TH) VGATE(TH) VGATE(TH) VGATE(TH) VGATE(TH) GATE ON PWRGD 130ms 65ms 130ms 65ms 130ms 65ms 130ms 65ms 10s (NOT TO SCALE) 436112 F02 Figure 2. PWRGD Behavior 436112fb 8 LTC4361-1/LTC4361-2 Applications Information ON Input ON is a CMOS compatible, active low enable input. It has a default 5A pull-down to ground. Connect this pin to ground or leave open to enable normal device operation. If it is driven high while the external MOSFET is turned on, GATE is pulled low with a weak pull-down current (40A) to turn off the external MOSFET gradually, minimizing input voltage transients. The LTC4361 then goes into a low current sleep mode, drawing only 1.5A at IN. When ON goes back low, the part restarts with a 130ms delay cycle. GATEP Control GATEP has a 2M resistive pull-down to ground and a 5.8V Zener clamp in series with a 200k resistor to IN. It controls the gate of an optional external P-channel MOSFET to provide negative voltage protection. The 2M resistive pull-down turns on the MOSFET once VIN - VGATEP is more than the MOSFET gate threshold voltage. The IN to GATEP Zener protects the MOSFET from gate overvoltage by clamping its VGS to 5.8V when VIN goes high. MOSFET Configurations and Selection The LTC4361 can be used with various external MOSFET configurations (see Figure 3). The simplest configuration is a single N-channel MOSFET. It has the lowest RDS(ON) and voltage drop and is thus the most power efficient solution. When GATE is pulled to ground, the N-channel MOSFET can isolate OUT from a positive voltage at IN up to the BVDSS of the N-channel MOSFET. However, reverse current can still flow from OUT to IN via the parasitic body diode of the N-channel MOSFET. For near zero reverse-leakage current protection when GATE is pulled to ground, back-to-back N-channel MOSFETs can be used. Adding an additional P-channel MOSFET controlled by GATEP provides negative input voltage protection down to the BVDSS of the P-channel MOSFET. Another configuration consists of a P-channel MOSFET controlled by GATEP and a N-channel MOSFET controlled by GATE. This provides protection against overvoltage and negative voltage but not reverse current. RSENSE SUPPLY IN OVERVOLTAGE PROTECTION M1 OUT SENSE GATE RSENSE SUPPLY IN OVERVOLTAGE, REVERSECURRENT PROTECTION M1 M3 OUT SENSE GATE SUPPLY NEGATIVE VOLTAGE PROTECTION M2 RSENSE IN GATE NEGATIVE VOLTAGE PROTECTION M2 RSENSE IN GATEP OUT SENSE GATEP SUPPLY OVERVOLTAGE, REVERSECURRENT PROTECTION M1 M3 OVERVOLTAGE PROTECTION M1 OUT SENSE GATE 436112 F03 Figure 3. MOSFET Configurations 436112fb 9 LTC4361-1/LTC4361-2 Applications Information WALL ADAPTOR AC/DC RIN LIN MOBILE DEVICE IN ICABLE VIN 10V/DIV COUT + CABLE LOAD ICABLE 20A/DIV 436112 F04a 5s/DIV RIN = 150m, LIN = 0.7H LOAD = 10, COUT = 10F 436112 F04b 5s/DIV RIN = 150m, LIN = 0.7H, RSENSE = 25m LOAD = 10, COUT = 10F 436112 F05b Figure 4. 20V Hot-Plug into a 10F Capacitor WALL ADAPTOR AC/DC RIN LIN IN RSENSE M1 Si1470DH OUT MOBILE DEVICE VIN 10V/DIV ICABLE + GATE CABLE COUT SENSE OUT LTC4361 IN LOAD VOUT 1V/DIV ICABLE 20A/DIV GND 436112 F05a Figure 5. 20V Hot-Plug into the LTC4361 Input Transients Figure 4 shows a typical setup when an AC wall adaptor charges a mobile device. The inductor LIN represents the lumped equivalent inductance of the cable and the EMI filter found in some wall adaptors. RIN is the lumped equivalent resistance of the cable, adaptor output capacitor ESR and the connector contact resistance. LIN and RIN form an LC tank circuit with any capacitance at IN. If the wall adaptor is powered up first, plugging the wall adaptor output to IN does the equivalent of applying a voltage step to this LC circuit. The resultant voltage overshoot at IN can rise to twice the DC output voltage of the wall adaptor as shown in Figure 4. Figure 5 shows the 20V adaptor output applied to the LTC4361. Due to the low capacitance at the IN pin, the plug-in transient has been brought down to a manageable level. 436112fb 10 LTC4361-1/LTC4361-2 Applications Information As the IN pin can withstand up to 80V, a high voltage N-channel MOSFET can be used to protect the system against rugged abuse from high transient or DC voltages up to the BVDSS of the MOSFET. Figure 6 shows a 50V input plugged into the LTC4361 controlling a 60V rated MOSFET. Input transients also occur when the current through the cable inductance changes abruptly. This can happen when the LTC4361 turns off the N-channel MOSFET rapidly in an overvoltage or overcurrent event. Figure 7 shows an input transient after an overcurrent. The current in LIN will cause VIN to overshoot and avalanche the N-channel MOSFET to COUT . Typically, IN will be clamped to a voltage of VOUT + 1.3 * (BVDSS of Si1470DH) = 45V. This is well below the 85V absolute maximum voltage rating of the LTC4361. The single, nonrepetitive, pulse of energy (EAS) absorbed by the MOSFET during this avalanche breakdown with a peak current IAS is approximated by the formula: EAS = 0.5 * LIN * IAS2 For LIN = 0.7H and IAS = 4A, then EAS = 5.6J. This is within the IAS and EAS capabilities of most MOSFET's including the Si1470DH. So in most instances, the LTC4361 can ride through such transients without a bypass capacitor, transient voltage suppressor or other external components at IN. Note that if an IN bypass capacitor is used, the VIN transients will overshoot less but last longer. If VIN dips below VIN(UVL) for more than 10s, the internal latch-off latch in the LTC4361-1 could be inadvertently reset. VIN 20V/DIV VIN 20V/DIV VOUT 5V/DIV VGATE 10V/DIV VOUT 1V/DIV ICABLE 5A/DIV ICABLE 5A/DIV 436112 F06 5s/DIV FDC5612 RIN = 150m, LIN = 0.7H RSENSE = 25m, LOAD = 10, COUT = 10F 436112 F07 2s/DIV FIGURE 5 CIRCUIT RIN = 150m, LIN = 0.7H RSENSE = 25m, LOAD = 10, COUT = 10F Figure 6. 50V Hot-Plug into the LTC4361 Figure 7. Overcurrent Turn-Off and Resulting Input Transient 436112fb 11 LTC4361-1/LTC4361-2 Applications Information Figure 8 shows a particularly severe situation which can occur in a mobile device with dual power inputs. A 20V wall adaptor is mistakenly hot-plugged into the 5V device with the USB input already live. As shown in Figure 9, a large current can build up in LIN to charge up COUT . When the N-channel MOSFET shuts off, the energy stored in LIN is dumped into COUT, causing a large 40V input transient. The LTC4361 limits this to a 1V rise in the output voltage. the MOSFET before VOUT overshoots to a dangerous voltage. A larger COUT also helps to lower the VOUT due to the discharge of the energy in LIN if the MOSFET BVDSS is used as an input clamp. Layout Considerations Figure 10 shows an example PCB layout for the LTC4361 (TS8 package) with a single N-channel MOSFET (SC70 package) and a 0603 size sense resistor. Keep the traces to the N-channel MOSFET wide and short. The PCB traces associated with the power path through the N-channel MOSFET should have low resistance. Use Kelvin connections to RSENSE for an accurate overcurrent threshold. If the VOUT due to the discharge of the energy in LIN into COUT is not acceptable or the avalanche capability of the MOSFET is exceeded, an additional external clamp such as the SMAJ24A can be placed between IN and GND. COUT is the decoupling capacitor of the protected circuits and its value will largely be determined by their requirements. Using a larger COUT will work with LIN to slow down the dV/dt at OUT, allowing time for the LTC4361 to shut off RIN 20V WALL ADAPTER + VIN 20V/DIV LIN ICABLE IN RSENSE - OUT GATE LTC4361 SENSE + - VOUT 5V/DIV VGATE 10V/DIV D1 B160 5V USB M1 Si1470DH R1 100k IN COUT ICABLE 10A/DIV LOAD OUT 436112 F09 1s/DIV FIGURE 8 CIRCUIT RIN = 150m LIN = 2H, RSENSE = 25m, LOAD = 10 COUT = 10F (16V, SIZE 1210) GND 436112 F08 Figure 8. Setup for Testing 20V Plugged into 5V System Figure 9. Overvoltage Protection Waveforms When 20V Plugged into 5V System 1 2 3 4 LTC4361 GND 4 5 6 3 Si1470DH 2 RSENSE OUT 1 SUPPLY 8 7 6 5 IN 436112 F10 Figure 10. Layout for N-Channel MOSFET Configuration 436112fb 12 LTC4361-1/LTC4361-2 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. DC8 Package 8-Lead Plastic DFN (2mm x 2mm) (Reference LTC DWG # 05-08-1719 Rev A) 0.70 0.05 2.55 0.05 1.15 0.05 0.64 0.05 (2 SIDES) PACKAGE OUTLINE 0.25 0.05 0.45 BSC 1.37 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED R = 0.05 TYP 2.00 0.10 (4 SIDES) PIN 1 BAR TOP MARK (SEE NOTE 6) R = 0.115 TYP 5 8 0.40 0.10 0.64 0.10 (2 SIDES) PIN 1 NOTCH R = 0.20 OR 0.25 x 45 CHAMFER (DC8) DFN 0409 REVA 4 0.200 REF 1 0.23 0.05 0.45 BSC 0.75 0.05 1.37 0.10 (2 SIDES) 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 436112fb 13 LTC4361-1/LTC4361-2 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. TS8 Package 8-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1637 Rev A) 0.40 MAX 2.90 BSC (NOTE 4) 0.65 REF 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.22 - 0.36 8 PLCS (NOTE 3) 0.65 BSC 0.80 - 0.90 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) 1.95 BSC TS8 TSOT-23 0710 REV A NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 436112fb 14 LTC4361-1/LTC4361-2 Revision History REV DATE DESCRIPTION PAGE NUMBER A 01/11 Revised conditions for VGATE(CLP) and tOFF in Electrical Characteristics section 3 Revised GATE Control in Applications Information section 7 B 05/12 Added H-grade order information 2 Change to Electrical Characteristics Input Undervoltage Lockout 3 Added VIN(OVL) specifications 3 Change to Electrical Characteristics Overvoltage Hysteresis 3 Change to Electrical Characteristics GATE Pull-Up and Pull-Down Current 3 Change to Electrical Characteristics GATE Ramp-Up 3 Added ISENSE(IN) specifications 3 Change to Electrical Characteristics ON Pull-Down Current 3 Change to Electrical Characteristics IN to GATEP Clamp Voltage 3 Change to Electrical Characteristics GATEP Resistive Pull-Down 3 Change to Electrical Characteristics PWRGD Pull-Up Resistance to OUT 3 Change to Electrical Characteristics GATE On Delay 3 Change to Electrical Characteristics PWRGD Delay 3 Replaced GATE Fast Pull-Down Current vs Temperature Curve 4 Added PCB trace to short pin 3 to pin 5 in Figure 10 12 Added packaging link 13, 14 436112fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC4361-1/LTC4361-2 Typical Application 5V System Protected from 24V Power Supplies and Overcurrent VIN 5V M2 Si3590DV RSENSE 0.05 M1 COUT 10F VOUT 5V 0.5A 5V System Protected from 24V Power Supplies, Overcurrent and Reverse Current VIN 5V M2 Si1471DH FDC6561AN RSENSE 0.05 M1 M3 COUT 10F GATE VOUT 5V 0.5A GATE SENSE OUT SENSE VIO 5V LTC4361 OUT VIO 5V LTC4361 IN IN R1 1k GATEP ON D1 LN1351CTR PWRGD GND R1 1k GATEP ON GND 436112 TA02 D1 LN1351CTR PWRGD 436112 TA03 Related Parts PART NUMBER DESCRIPTION COMMENTS LTC2935 Ultralow Power Supervisor with Eight Pin-Selectable Thresholds 500nA Quiescent Current, 2mm x 2mm 8-Lead DFN and TSOT-23 Packages LT3008 20mA, 45V, 3A IQ Micropower LDO 280mV Dropout Voltage, Low IQ: 3A, VIN = 2.0V to 45V, VOUT = 0.6V to 39.5V; ThinSOT and 2mm x 2mm DFN-6 Packages LT3009 20mA, 3A IQ Micropower LDO 280mV Dropout Voltage, Low IQ: 3A, VIN = 1.6V to 20V, VOUT = 0.6V to 19.5V; ThinSOT and SC-70 Packages LTC3576/ LTC3576-1 Switching USB Power Manager with USB OTG + Triple Complete Multifunction PMIC: Bi-Directional Switching Power Manager + 3 Step-Down DC/DCs Bucks + LDO LTC4090/ LTC4090-5 High Voltage USB Power Manager with Ideal Diode Controller and High Efficiency Li-Ion Battery Charger High Efficiency 1.2A Charger from 6V to 38V (60V Max) Input Charges Single Cell Li-Ion Batteries Directly from a USB Port LTC4098 USB-Compatible Switchmode Power Manager with OVP High VIN: 38V operating, 60V transient; 66V OVP. 1.5A Max Charge Current from Wall, 600mA Charge Current from USB LTC4210 Single Channel, Low Voltage Hot SwapTM Controller Operates from 2.7V to 16.5V, Active Current Limiting, SOT23-6 LTC4213 No RSENSETM Electronic Circuit Breaker Controls Load Voltages from 0V to 6V. 3 Selectable Circuit Breaker Thresholds. Dual Level Overcurrent Fault Protection LT4356 Surge Stopper- Overvoltage/Overcurrent Protection Regulator Wide Operation Range: 4V to 80V. Reverse Input Protection to -60V. Adjustable Output Clamp Voltage LTC4411 SOT-23 Ideal Diode 2.6A Forward Current, 28mV Regulated Forward Voltage LTC4412 2.5V to 28V, Low Loss PowerPathTM Controller in ThinSOT More Efficient than Diode-ORing, Automatic Switching Between DC Sources, Simplified Load Sharing LTC4413-1/ LTC4413-2 Dual 2.6A, 2.5V to 5.5V Fast Ideal Diodes in 3mm x 3mm DFN 130m On Resistance, Low Reverse Leakage Current, 18mV Regulated Forward Voltage (LTC4413-2 with Overvoltage Protection Sensor) 436112fb 16 Linear Technology Corporation LT 0512 REV B * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com LINEAR TECHNOLOGY CORPORATION 2010