DATA SHEET Form 0252-180912 PAGE 1 G4 DIGITAL AC OUTPUT MODULES Features > > > > > > > > 4000 volts optical isolation (transient) Built-in LED status indicator Logic levels of 5, 15, and 24 VDC Removable fuse Current rating: 3 amps at 45 C UL Motor Load rating: 1.5 amps Ability to withstand one-cycle surge of 80 amps Operating temperature: -30 C to 70 C G4OAC5A and G4OAC5AMA Modules DESCRIPTION Opto 22's G4 AC output modules are used to control or switch AC loads. Each module provides up to 4000 volts of optical isolation (transient) between field outputs and the control side of the circuit, and each features zero voltage turn-on and zero current turn-off. All AC output modules are equivalent to single-pole, single-throw, normally open contacts (Form A, SPST-NO) except the G4OAC5A5, which is equivalent to a single-pole, single-throw, normally closed contact (Form B, SPST-NC). Each module is equipped with a 4 amp fast-blow fuse. The fuse breaking capacity is 40 amps at 250 VAC. Current should be limited to prevent the short circuit current from exceeding the rated breaking capacity of the fuse. Typical applications for AC output modules include switching loads such as AC relays, solenoids, motor starters, heaters, lamps, and indicators. Part Numbers Part Description G4OAC5* G4 AC Output 12-140 VAC, 5 VDC Logic G4OAC5FM G4 AC Output 12-140 VAC, 5 VDC Logic, Factory Mutual Approved G4OAC5A* G4 AC Output 24-280 VAC, 5 VDC Logic G4OAC5AFM G4 AC Output 24-280 VAC, 5 VDC Logic, Factory Mutual Approved The G4OAC5MA and the G4OAC5AMA are special modules featuring a manual-on/manual-off/automatic switch, ideal for diagnostic testing of control applications. G4OAC5A5* G4 AC Output 24-280 VAC, 5 VDC Logic NC G4OAC5A5FM G4 AC Output 24-280 VAC, 5 VDC Logic NC, Factory Mutual Approved Part numbers ending in FM are Factory Mutual approved. G4OAC5MA* G4 AC Output 12-140 VAC, 5 VDC Logic With Manual/Auto Switch Compatible with Raspberry Pi G4OAC5AMA* G4 AC Output 24-280 VAC, 5 VDC Logic With Manual/Auto Switch G4OAC15 G4 AC Output 12-140 VAC, 15 VDC Logic G4OAC15A G4 AC Output 24-280 VAC, 15 VDC Logic G4OAC24 G4 AC Output 12-140 VAC, 24 VDC Logic G4OAC24A G4 AC Output 24-280 VAC, 24 VDC Logic The following G4 digital AC output modules can be used with the Digital I/O Carrier Board for Raspberry Pi(R) (part number OPTO-P1-40P) to monitor and control industrial devices with your Raspberry Pi: * G4OAC5 * G4OAC5A * G4OAC5A5 * G4OAC5MA * G4OAC5AMA * Compatible with Raspberry Pi Raspberry Pi(R) is a trademark of the Raspberry Pi Foundation. OPTO 22 * 800-321-6786 * 1-951-695-3000 * www.opto22.com * sales@opto22.com (c) 2012-2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Form 0252-180912 PAGE 2 SPECIFICATIONS Units G4OAC5* G4OAC5FM** G4OAC5A* G4OAC5AFM** G4OAC5A5* G4OAC5A5FM** G4OAC5MA* G4OAC5AMA* Nominal line voltage VAC 120 120/240 120/240 120 120/240 Output voltage range VAC 12-140 24-280 24-280 12-140 24-280 Key feature -- -- -- Normally closed Diagnostic switch Diagnostic switch Current rating: At 45 C ambient At 70 C ambient A A 3 2 3 2 3 2 3 2 3 2 UL Motor Load Rating A 1.5 1.5 1.5 1.5 1.5 4000 1500 4000 1500 4000 1500 4000 1500 4000 1500 5 1.25/2.5 1.25/2.5 5 1.25/2.5 Isolation input-tooutput (transient): 1 ms 1 minute Off-state leakage at nominal voltage (60 Hz) volts mARMS Nominal logic voltage VDC 5 5 5 5 5 Logic voltage range VDC 4-8 4-8 4-8 4-8 4-8 Logic pickup voltage VDC 4 4 4 4 4 Logic dropout voltage VDC 1 1 1 1 1 Logic input current at nominal logic voltage mA 12 12 12 12 12 ohms 220 220 220 220 220 Control resistance (Rc in schematic) One-cycle surge A peak 80 80 80 80 80 8.3*** 8.3**** 8.3*** 8.3**** 8.3*** 8.3**** 8.3*** 8.3**** Turn-off time @ 60 Hz milliseconds 8.3*** 8.3**** Peak repetitive voltage VAC 500 500 500 500 500 Minimum load current Turn-on time @ 60 Hz milliseconds mA 20 20 20 20 20 Output voltage drop maximum peak V 1.6 1.6 1.6 1.6 1.6 Operating frequency Hz 25-65 25-65 25-65 25-65 25-65 V/micro-sec onds 200 200 200 200 200 dV/dT-commutating -- snubbed for 0.5 power factor load snubbed for 0.5 power factor load snubbed for 0.5 power factor load snubbed for 0.5 power factor load snubbed for 0.5 power factor load Temperature Operating: Storage: C C -30 to +70 -30 to +85 -30 to +70 -30 to +85 -30 to +70 -30 to +85 -30 to +70 -30 to +85 -30 to +70 -30 to +85 dV/dT-off-state * Compatible with Raspberry Pi ** Part numbers ending in FM are Factory Mutual approved. *** One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave. **** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave. OPTO 22 * 800-321-6786 * 1-951-695-3000 * www.opto22.com * sales@opto22.com (c) 2012-2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Form 0252-180912 PAGE 3 SPECIFICATIONS (CONT.) Units G4OAC15*** G4OAC15A*** G4OAC24*** G4OAC24A*** Nominal line voltage VAC 120 120/240 120 120/240 Output voltage range VAC 12-140 24-280 12-140 24-280 Key feature -- -- -- -- -- Current rating: At 45 C ambient At 70 C ambient A A 3 2 3 2 3 2 3 2 UL Motor Load Rating A 1.5 1.5 1.5 1.5 volts 4000 1500 4000 1500 4000 1500 4000 1500 mARMS 5 1.25/2.5 5 1.25/2.5 Logic voltage range VDC 10.5-16 10.5-16 19.5-32 19.5-32 Logic pickup voltage VDC 10.5 10.5 19.5 19.5 Logic dropout voltage VDC 1 1 1 1 mA 15 15 18 18 ohms 1K 1K 2.2 K 2.2 K A peak 80 80 80 80 Turn-on time @ 60 Hz microseconds 8.3* 8.3* 8.3* 8.3* Turn-off time @ 60 Hz microseconds 8.3** 8.3** 8.3** 8.3** Peak repetitive voltage VAC 500 500 500 500 Minimum load current mA 20 20 20 20 Isolation input-to-output (transient): 1 ms 1 minute Off-state leakage at nominal voltage (60 Hz) Logic input current at nominal logic voltage Control resistance (Rc in schematic) One-cycle surge Output voltage drop maximum peak V 1.6 1.6 1.6 1.6 Operating frequency Hz 25-65 25-65 25-65 25-65 V/microsecond 200 200 200 200 dV/dT-commutating -- snubbed for 0.5 power factor load snubbed for 0.5 power factor load snubbed for 0.5 power factor load snubbed for 0.5 power factor load Temperature Operating: Storage: C C -30 to +70 -30 to +85 -30 to +70 -30 to +85 -30 to +70 -30 to +85 -30 to +70 -30 to +85 dV/dT-off-state * One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave. ** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave. *** Not for use with Opto 22 brains. OPTO 22 * 800-321-6786 * 1-951-695-3000 * www.opto22.com * sales@opto22.com (c) 2012-2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Form 0252-180912 PAGE 4 DIMENSIONS SCHEMATICS OPTO 22 * 800-321-6786 * 1-951-695-3000 * www.opto22.com * sales@opto22.com (c) 2012-2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. More about Opto 22 PRODUCTS * Opto 22 develops and manufactures reliable, easy-to-use, open standards-based hardware and software products. Industrial automation, process control, building automation, industrial refrigeration, remote monitoring, data acquisition, and industrial internet of things (IIoT) applications worldwide all rely on Opto 22. groov EPIC(R) System Opto 22's groov Edge Programmable Industrial Controller (EPIC) system is the culmination of over 40 years of experience in designing products for the automation industry. groov EPIC gives you an industrially hardened system with guaranteed-for-life I/O, a flexible Linux(R)-based controller with gateway functions, and software for your IIoT application or any application. groov EPIC I/O Ignition Edge(R) from Inductive Automation(R), with OPC-UA drivers to Allen-Bradley(R), Siemens(R), and other control systems, and MQTT/Sparkplug communications for efficient IIoT data transfer groov Edge Appliance Visualization, data handling, and connectivity in a compact, industrial box: that's the groov Edge Appliance. Included are: * groov View for building and viewing operator interfaces on PCs and mobile * Node-RED for building simple logic flows * Ignition Edge(R) from Inductive Automation(R), for OPC-UA drivers and MQTT/Sparkplug IIoT communications Older products From solid state relays (our first products) to world-famous G4 and SNAP I/O, to SNAP PAC controllers, Opto 22 products last a long time. You can count on us to give you the reliability and service you expect. I/O provides the local connection to sensors and equipment. groov I/O offers up to 24 channels on each I/O module, with a spring-clamp terminal strip, integrated wireway, and swingaway cover. QUALITY Founded in 1974, Opto 22 has established a worldwide reputation for high-quality products. All are made in the U.S.A. at our manufacturing facility in Temecula, California. Opto 22 I/O is so reliable, we can afford to guarantee it for life. groov I/O is hot swappable, UL Hazardous Locations approved, and ATEX compliant. Because we test each product twice before it leaves our factory rather than testing a sample of each batch, we can guarantee most solid-state relays and optically isolated I/O modules for life. groov EPIC Controller The heart of the system is the groov EPIC controller. It handles a wide range of digital, analog, and serial functions for data collection, remote monitoring, process control, and discrete and hybrid manufacturing. In addition, the EPIC provides secure data communications among physical assets, control systems, software applications, online services, and more, both on premises and in the cloud. Configuring and troubleshooting I/O and networking is easier with the EPIC's integrated high-resolution touchscreen. Authorized users can see your groov View HMI locally on the touchscreen or on a monitor connected via the HDMI or USB ports. groov EPIC Software Software includes: * Flowchart-based PAC Control for control programming, or build your own custom application with optional secure shell access * groov View for building and viewing your own deviceindependent HMI * Node-RED for creating simple logic flows from pre-built nodes OPTO 22 * www.opto22.com 43044 Business Park Dr. Temecula, CA 92590-3614 FREE PRODUCT SUPPORT Opto 22's California-based Product Support Group offers free, comprehensive technical support for Opto 22 products from engineers with decades of training and experience. Support is available in English and Spanish by phone or email, Monday-Friday, 7 a.m. to 5 p.m. PST. Support is always available on our website, including how-to videos, user's guides, the Opto 22 KnowledgeBase, troubleshooting tips, and OptoForums. In addition, free hands-on training is available at our Temecula, California headquarters, and you can register online. PURCHASING OPTO 22 PRODUCTS Opto 22 products are sold directly and through a worldwide network of distributors, partners, and system integrators. For more information, contact Opto 22 headquarters at 800-321-6786 (toll-free in the U.S. and Canada) or +1-951-695-3000, or visit our website at www.opto22.com. SALES * sales@opto22.com 800-321-6786 * 1-951-695-3000 SUPPORT * support@opto22.com 800-835-6786 * 1-951-695-3080 (c) 2006-2018 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1335-180323