MODEL 834M1 ACCELEROMETER SPECIFICATIONS Triaxial Piezoelectric Accelerometer <22A Current Consumption Wide Bandwidth to 6kHz Circuit Board Mountable The Model 834M1 is a low cost, board mountable triaxial accelerometer designed for high amplitude embedded shock applications. The accelerometer features a maximum current consumption of 22 micro-amps and incorporates full power and signal conditioning. The model 834M1 is available in 2000g to 6000g ranges and provides a flat frequency response up to greater than 6kHz. The standard model 834 offers the same envelope with a lower maximum current consumption of 4 micro-amps. FEATURES 2000g to 6000g Dynamic Range Low Cost Triaxial Hermetically Sealed Piezo-ceramic Crystals -40 to +125C Operating Range Single Axis Configurations Available APPLICATIONS SENSOR SOLUTIONS /// Model 834M1 Rev F Asset Monitoring Impact Testing System Wake-Up Switch Embedded Applications Instrumentation 12/2017 Page 1 MODEL 834M1 ACCELEROMETER PERFORMANCE SPECIFICATIONS All values are typical at +24C, 80Hz and 3.3Vdc excitation unless otherwise stated. TE Connectivity reserves the right to update and change these specifications without notice. Parameters DYNAMIC Range (g) Sensitivity (mV/g) Frequency Response (Hz) Natural Frequency (Hz) Non-Linearity (%FSO) Transverse Sensitivity (%) Shock Limit (g) Broadband Noise (V) Spectral Noise (mg/Hz) Spectral Noise (mg/Hz) Spectral Noise (mg/Hz) 2000 0.62 2-6000 >30000 2 <8 10000 40 3.2 0.6 0.2 ELECTRICAL Bias Voltage (Vdc) Total Supply Current (A) 1 Excitation Voltage (Vdc) Output Impedance () Insulation Resistance (M) Shielding Ground Isolation Exc Voltage / 2 <22 3.3 to 5.5 <100 >50 100% Isolated from Mounting Surface ENVIRONMENTAL Temperature Response (%) Operating Temperature (C) Storage Temperature (C) Humidity -20/+30 from -40C to +125C -40 to +125 -40 to +125 Hermetically Solder Sealed PHYSICAL Sensing Element Case Material Weight (grams) Ceramic (shear mode) Ceramic Base, Nickel Silver Cover 2.6 Notes 6000 0.20 2-6000 >30000 2 <8 10000 30 4.0 1.0 0.5 30% 2dB 0.1Hz-10kHz @ 10Hz @ 100Hz @ 1000Hz @100Vdc 1 A lower current consumption of 4 micro-amps is available on model 834. The model 834M1 is not to be reflow soldered at high temperature, manual soldering is recommended. See operating manual. 3 The model 834M1 can be operated with 2.8V excitation but the full-scale range will be limited. See operating manual for details. 2 Calibration supplied: CS-SENS-0100 NIST Traceable Amplitude Calibration at 80Hz The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. TE Connectivity reserves the right to make changes without further notice to any product herein. TE Connectivity makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does TE Connectivity assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer's technical experts. TE Connectivity does not convey any license under its patent rights nor the rights of others. SENSOR SOLUTIONS /// Model 834M1 Rev F 12/2017 Page 2 MODEL 834M1 ACCELEROMETER DIMENSIONS SCHEMATIC SENSOR SOLUTIONS /// Model 834M1 Rev F 12/2017 Page 3 MODEL 834M1 ACCELEROMETER ORDERING INFORMATION 834M1 GGGG Range 2000=2000g 6000=6000g Example; 834M1-6000 Model 834M1, 6000g range NORTH AMERICA EUROPE ASIA Measurement Specialties, Inc., a TE Connectivity Company Tel: 800-522-6752 customercare.hmpt@te.com MEAS France SAS a TE Connectivity Company Tel: +31 73 624 6999 customercare.lcsb@te.com Measurement Specialties (China), Ltd., a TE Connectivity Company Tel: 0400-820-6015 customercare.shzn@te.com TE.com/sensorsolutions MEAS France SAS and Measurement Specialties (China) , Inc., are TE Connectivity companies. TE Connectivity, TE, TE connectivity (logo) are trademarks. All other logos, products and/or company names referred to herein might be trademarks of their respective owners. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity`s obligations shall only be as set forth in TE Connectivity`s Standard Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application. (c) 2017 TE Connectivity Ltd. All Rights Reserved. SENSOR SOLUTIONS /// Model 834M1 Rev F 12/2017 Page 4