MLX90277EGOSR1-0 - Melexis - Product.Network

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 1 of 21 Data Sheet

Rev 004 Nov/06

Features and Benefits

 Full Redundant Sensor

 Analog Signal Processing

 Quad Switched Hall Plate

 Chopper Stabilized Amplifier

 Linear Analog Ratiometric Output Voltage

 Programmable Output Quiescent Voltage (V

)

-100%V

…200%V

Range

 Programmable Magnetic Sensitivity

 Programmable Low Pass Filter

 Programmable Clamping Voltage

 Programmable Temperature Compensation

 Melexis ID Number

 Programmable Customer ID Number

 Lead-free package

Application Examples

 Linear Position Sensing

 Rotary Position Sensing

 Current Sensing

 Magnetic Field Measurement

Ordering Information

Part No. Temperature Code Package Code Option Code SR(IC_A, IC_B)

†

MLX90277 E (-40°C to 85°C) GO (TSSOP 14) SRA-B, (A = 0, 1, 2, or 3)

(B = 0, 1, 2, or 3)

Example: MLX90277EGO SR2-1

†

Please see section 10.4 for detailed information on the option codes.

1 Functional Diagram

OPA

DAC

Shift Register

E E P R O M

OPA

DAC

Filter

DAC

Supply

Program

decoder

DAC

Figure 1-1 Functional Diagram

TSSOP 14 pin out

IC_A IC_B

Vdd 3 10

Out 12 5

Vss (Ground) 14 6

Test 2 9

NC 1 - 4 - 7 - 8 - 11 - 13

Table 1: Pin out

2 General Description

The MLX90277 is a Dual Programmable

Ratiometric Linear Hall Effect sensor. Two

discrete CMOS ICs are mounted inside a single

package, electrically insulated, and independently

programmable. The MLX90277 is suitable for

applications requiring full redundancy. The linear

output voltages are proportional to the magnetic

flux density. The ratiometric output voltages are

proportional to the supply voltages. The

MLX90277 possesses active error correction

circuitry, which virtually eliminates the offset errors

normally associated with analog Hall Effect

devices. All the parameters of the MLX90277

transfer characteristic are fully programmable.

The V

OUT

@ B = 0 Gauss), the Sensitivity,

the slope polarity, the Output Clamping levels, the

thermal Sensitivity drift, the internal bias point and

a low-pass filter are all programmable in end-user

applications. The MLX90277 has a very stable

thermal compensation for both the Sensitivity and

the V

over a broad temperature range. For

traceability purpose the MLX90277 will carry a

unique ID number programmed by Melexis and 24

bits of EEPROM memory are allocated for a user

programmed serial number.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 2 of 21 Data Sheet

Rev 004 Nov/06

Table of Contents

1 Functional Diagram ........................................................................................................... 1

2 General Description .......................................................................................................... 1

3 Glossary of Terms............................................................................................................. 3

4 Maximum Ratings ............................................................................................................. 3

5 Detailed Block Diagram..................................................................................................... 4

5.1 Detailed Description .................................................................................................... 4

6 General Electrical Specifications....................................................................................... 5

7 Programming Range ......................................................................................................... 6

8 Timing Specifications ........................................................................................................ 6

9 Accuracy ........................................................................................................................... 6

10 Programmable Features ................................................................................................. 7

10.1 Output Quiescent Voltage (V

)................................................................................ 8

10.2 Thermal V

Drift (DRIFT) ........................................................................................ 8

10.3 Sensitivity, Rough Gain and Fine Gain ..................................................................... 8

10.4 Sensitivity Range Selection....................................................................................... 9

10.5 Sensitivity Polarity (INVERT)................................................................................... 11

10.6 Clamping Levels (CLAMPLOW, CLAMPHIGH)....................................................... 11

10.7 Filter (FILTER) ........................................................................................................ 12

10.8 Sensitivity Temperature Compensation (TC, TCW, TC

) ........................................ 12

10.9 Diagnostic Output Level (FAULTLEV)..................................................................... 13

10.10 The EEPROM, Parity and Melexis CRC ............................................................... 13

10.11 Output Amplifier Configuration (MODE) ................................................................ 14

10.12 Memory Lock (MEMLOCK) ................................................................................... 14

10.13 IC traceability ........................................................................................................ 14

11 Performance Graphs..................................................................................................... 14

12 Applications Information................................................................................................ 15

12.1 Application Circuits.................................................................................................. 15

12.2 Programming the Sensor ........................................................................................ 16

12.3 Calibration Procedure ............................................................................................. 17

13 Standard information regarding manufacturability of Melexis products with different

soldering processes ........................................................................................................... 18

14 ESD Precautions........................................................................................................... 18

15 Package Information ..................................................................................................... 19

15.1 Package Dimensions .............................................................................................. 19

15.2 Pin-out and Marking ................................................................................................ 20

15.3 Hall Plate Positioning .............................................................................................. 20

16 Disclaimer ..................................................................................................................... 21

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 3 of 21 Data Sheet

Rev 004 Nov/06

Note: All specifications apply to IC_A and IC_B unless otherwise noted.

3 Glossary of Terms

 mT (milli-Tesla) = Unit of measurement for magnetic flux density. 1mT is equal to 10 Gauss.

 V

(Output Quiescent Voltage) = Output voltage at zero magnetic field, V

OUT

for B = 0 mT.

 Sensitivity = Change in output voltage versus change in magnetic field, ∆ V

OUT

/ ∆ B.

 TempCo (Sensitivity Temperature Compensation) = Change in Sensitivity over temperature. Listed

in units of ppm / °C (100ppm / °C. = 0.01 % / °C.).

 PTC (Programming Through the Connector) = Melexis in circuit programming protocol.

 MSB = Most Significant Bit.

 LSB = Least Significant Bit.

4 Maximum Ratings

Table 2: Absolute Maximum Ratings

Note: Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolute-

maximum-rated conditions for extended periods may affect device reliability.

Parameter Units

Maximum Supply Voltage, V

DD_MAX

(Over

Voltage)

30 V

Maximum Supply Current, I

DD_MAX

(Over Voltage)

50 mA

Reverse Voltage, V

DD_REV

- 15 V

Reverse Supply Current, I

DD_REV

- 85 mA

Positive Output Voltage, V

OUT_MAX

24 V

Positive Output Current, I

OUT_POS_FAULT

40 mA

Reverse Output Voltage, V

OUT_REV

- 0.7 V

Reverse Output Current, I

OUT_REV_FAULT

-50 mA

Operating Ambient Temperature Range, T

-40°C to 150°C

Storage Temperature Range, T

-55°C to 165°C

Magnetic Flux Density Infinite

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 4 of 21 Data Sheet

Rev 004 Nov/06

5 Detailed Block Diagram

Figure 5-1 Detailed Block Diagram

5.1 Detailed Description

Integrated on each individual IC within the MLX90277 is a temperature-compensated quad switched Hall

plate, chopper stabilized amplifiers, adjustable output filter, output driver, voltage protection circuitry and a

programmable EEPROM with security and redundancy. Programming the EEPROM allows each device to be

calibrated in the application.

In normal operation data stored in the EEPROM feeds a register, RAM, that updates internal DACs and

switches that effect the operation of the device. In programming mode the RAM can be directly accessed to

allow faster calibration of the parameters. Communication to the device is done using Melexis' PTC serial

interface.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 5 of 21 Data Sheet

Rev 004 Nov/06

6 General Electrical Specifications

DC operating parameters at V

= 5V (unless otherwise specified) and for T

as specified by the temperature

range (E).

Parameter Symbol Test Conditions Min Typical

Max Units

Nominal Supply Voltage V

DDNOM

- 5 - V

Operating Supply Voltage V

DD†

4.5 - 5.5 V

Nominal Supply Current I

DDNOM

= V

DDNOM

4.0 7.0 8.0 mA

Supply Current I

= 4.5 … 5.5 V 3.0 - 9.0 mA

OUTPD

Pull Down Load ≥ 10 kΩ

no clamping 2 96 %V

Output Voltage Swing

OUTPU

Pull Up Load ≥ 10 kΩ

no clamping 5 97 %V

Output Current I

OUT

= V

DDNOM

-1.25 1.25 mA

Output Short-Circuit Current

OUTSC+

OUTSC-

= V

DDNOM

Output shorted to supply-permanent

Output shorted to ground-permanent

-12

-4

OUT1

Broken supply,

Pull-down load > 10 kΩ 0 0.5

OUT2

Broken ground,

Pull-down load > 10 kΩ 94 96 100

OUT3

Broken supply,

Pull-up load > 10 kΩ 0 3 5

Diagnostic Output Voltage

OUT4

Broken ground,

Pull-up load > 10 kΩ 99.5 100

Power on Reset V

DD_POR

Voltage on V

1.5 3.8 V

Over Voltage Detection V

DD_OVD

Voltage on V

6.5 8.5 V

Substrate Insulation R

DIES

200VDC across V

SS1

and V

SS2

0 50 µA

Table 3: Electrical Specifications

†

The ratiometric output voltage is proportional to the supply voltage. When using the supply voltage as a

reference for an A/D converter, fluctuations of ±10% in supply voltage are compensated.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 6 of 21 Data Sheet

Rev 004 Nov/06

7 Programming Range

programming 20°C to 30°C.

Parameter Symbol Test Conditions Min Typical

Max Units

Output Quiescent Voltage V

AGND = Default

AGND = 0…1023

-10

-100

110

200

Sensitivity S 2.6 210 mV/mT

Output Clamping Voltage Low ClampLo 0 100 %V

Output Clamping Voltage High ClampHi 0 100 %V

Temperature Compensation TempCo 1

order 0 2300 ppm / °C

Table 4: Programming Range Specifications

8 Timing Specifications

DC operating parameters at V

= 5V (unless otherwise specified) and for T

as specified by the temperature

range (E).

Parameter Symbol Test Conditions Min Typical

Max Units

Power On Delay T

FILTER = 0, RG = 0

FILTER = 0, RG = 15

FILTER = 15, RG = 0

FILTER = 15, RG = 15

0.4

0.6

1.1

0.8

1.2

2.2

Step Response Time RG = 0 to 3, FILTER = 0

RG = 4 to 7, FILTER = 0

RG = 8 to 11, FILTER = 0

RG = 12 to 15, FILTER = 0

100

200

132

264

µs

Table 5: Timing Specifications

9 Accuracy

DC operating parameters at V

= 5V (unless otherwise specified) and for T

as specified by the temperature

range (E).

Parameter Symbol

††

Test Conditions Min Typical

Max Units

Thermal Voq Drift ∆

= 2.5V

(1)

, 25°C / 150°C

= 2.5V

(1)

, 25°C / -40°C

- 0.2

- 0.4

+ 0.2

+ 0.4

Life Time Drift of the Thermal

Voq Drift

∆

- 0.2 + 0.2 %V

Life Time Voq Drift ∆

- 0.3 + 0.3 %V

Life Time Sensitivity Drift ∆

S - 1 + 1 %

Sensitivity Temperature

Coefficient

†

TCs 0 to 500 ppm / °C

500 to 1200 ppm / °C

1200 to 2300 ppm / °C

± 100

± 150

± 200

ppm / °C

Thermal Drift of Sensitivity

Temperature Compensation

∆

TC 150 ppm / °C

Thermal Drift Output Clamping

Levels

∆

OUTCLAMP

0.4

+ 0.4 %V

Life Time Drift Output Clamping

Levels

∆

OUTCLAMP

- 0.2 + 0.2 %V

Linearity error Le 0.2 %

Table 6: Accuracy Specifications

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 7 of 21 Data Sheet

Rev 004 Nov/06

†

Valid for Rough Gain within the specified option code.

††

∆

= Life Time Drift (based on HTOL data [1000 hours @ 150°C]).

∆

= Thermal Drift.

(1)

For other test conditions, please contact the Melexis Sales representative of your area.

10 Programmable Features

The MLX90277 has many programmable features for adjusting the output characteristics. The parameters

are independently programmable for IC A and IC B. The features are utilized by writing data into the

redundant non-volatile EEPROM. Below is a quick list and description of all the programmable parameters.

Many of the parameters are set by Melexis and they are not used by the end customer. Later sections of the

data sheet give details on how the parameters are used.

Parameter Symbol Description Number of

Bits

Default

IC_A

Default

IC_B

Internal Bias Point AGND Coarse adjustment of V

. 10 Trimmed Trimmed

Analog Clock Choice

†

CKANACH Adjustment for amplifier clock generator. 2 Preset Preset

Clamping High CLAMPHIGH

Adjustment of upper output clamping

voltage.

10 768 256

Clamping Low CLAMPLOW Adjustment of lower output clamping

voltage.

10 768 256

Customer ID

††

CUSTID Open bits for customer programming. 24 Preset Preset

Offset Drift

†

DRIFT V

temperature drift compensation. 4 Trimmed Trimmed

EEPROM Fault Level FAULTLEV Output state for EEPROM parity error. 1 0 0

Fine Gain FG Fine adjustment for Sensitivity. 10 0 0

Filter FILTER Adjustment for low pass output filter. 4 0 0

Invert Slope INVERT Sensitivity polarity selection. 1 0 0

Memory Lock MEM_LOCK Used to lock the entire EEPROM. 1 0 0

Melexis ID

†

MLX_ID Melexis IC identification number. Preset Preset

Melexis Lock

†

MLX_LOCK Used to lock Melexis area of the EEPROM.

1 0 0

Output Driver

†

MODE Adjustment for output stage amplifier. 2 1 1

Offset DAC OFFSET Fine adjustment of V

. 10 0 0

Oscillator Adjust

†

OSCADJ Chip oscillator frequency adjustment. 4 Preset Preset

EEPROM Parity PARITY Ensures the integrity of the EEPROM data. 3 Calculated Calculated

Rough Gain RG Rough adjustment for Sensitivity. 4 0 0

Slow

†

SLOW Amplifier speed adjustment. 1 Preset Preset

Temperature

Compensation Window

TCW Range adjustment for Sensitivity

Temperature Compensation.

3 0 0

Temperature

Compensation

TC Fine adjustment of Sensitivity

Temperature Compensation.

5 0 0

2nd Order Temperature

Compensations

Linearization adjustment of the Sensitivity

Temperature Compensation.

6 0 0

Table 7: Programmable Parameters

†

Melexis parameter adjusted at final test.

††

Not included in redundant area of the EEPROM.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 8 of 21 Data Sheet

Rev 004 Nov/06

10.1 Output Quiescent Voltage (V

)

Two parameters, AGND and OFFSET, are used for adjustment of the V

. The AGND is a 10 bit parameter

for coarse adjustment of V

. It has a resolution of approximately 0.014V and a range of -100%V

200%V

. The OFFSET is a 10 bit parameter with a resolution of approximately -0.005V. The OFFSET

parameter is used for fine adjustment of the V

, while the AGND parameter is used to set the range. The

large adjustable range allows the MLX90277 to be used in an unipolar magnetic system without limiting the

output voltage span. The formula below shows how the AGND and OFFSET parameters combine to set the

OFFSET

AGND

00.5

1023

0.5

1023

25.14

75.0











∗−+











∗+−=

This formula approximates the typical V

of the MLX90277's individual sensors. The actual V

formula

varies slightly from IC to IC. Melexis calibrates the AGND setting during final test so that the V

approximately 50%V

with OFFSET set to 512. This gives the V

a range of 0%V

to 100%V

without

adjusting the AGND value. The OFFSET parameter is often used to set the application's offset output

transfer characteristic.

10.2 Thermal V

Drift (DRIFT)

The Thermal V

Drift is tuned using 4 bits. This parameter, DRIFT, is calibrated for each unit by Melexis

during final test. The value is set to achieve a V

accuracy below 10mV over a temperature span of 25°C to

150°C. This parameter is not used by the end customer.

10.3 Sensitivity, Rough Gain and Fine Gain

The Sensitivity of the MLX90277's individual sensors is controlled through parameters linked to dedicated

internal amplification stages. The parameter Rough Gain (RG), or pre-amplifier, has 4 bits for adjustment of

two stages. The two MSB affect the Differential Input Differential Output (DIDO) stage. The two LSB effect

the Differential to Single output (DTS) stage. The gain of both the DIDO and DTS are multiplied to get the

total RG. The table below shows typical values of the small signal amplifier gain vs. the parameter RG. The

pre-amplifier is chopper stabilized and the refresh frequency is adapted automatically to the RG setting to

match the chopper gain-bandwidth product.

Rough Gain (MSB LSB) DIDO DTS Gain

00 (00 00) 16 1.0 16

01 (00 01) 16 1.5 24

02 (00 10) 16 2.33 37

03 (00 11) 16 4.0 64

04 (01 00) 39 1.0 39

05 (01 01) 39 1.5 59

06 (01 10) 39 2.33 91

07 (01 11) 39 4.0 156

08 (10 00) 82 1.0 82

09 (10 01) 82 1.5 123

10 (10 10) 82 2.33 191

11 (10 11) 82 4.0 328

12 (11 00) 205 1.0 205

13 (11 01) 205 1.5 308

14 (11 10) 205 2.33 477

15 (11 11) 205 4.0 820

Table 8: MLX90277 Rough Gain Small Signal Amplifier Gain

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 9 of 21 Data Sheet

Rev 004 Nov/06

The MLX90277 sensors also have an additional stage, Fine Gain, for fine tuning the Sensitivity. The stage

(parameter FG) follows the RG and provides a 10 bit adjustment. The small signal gain of the FG is within

1.0 and 2.5. The RG and FG parameters are adjusted in the application to calibrate the sensitivity (gain) and

output slope transfer characteristic of the device. The function for the fine gain is given in the following

equation:

1023

*6.01

GainFine

−

Note. The one bit parameter INVERT is used to fix the “sign” of the sensitivity. A value of 0 makes the gain

positive and the output voltage increases in response to a South magnetic field. A value of 1 makes the gain

negative and the output voltage decrease in response to a South magnetic field. Refer to section 10.5,

Sensitivity Polarity for more information on INVERT.

10.4 Sensitivity Range Selection

Each unit is characterized over temperature during final test to optimize its performance and accuracy. To

achieve the best possible Sensitivity Temperature Compensation, TempCo., each unit is optimized for use

within a specific Sensitivity range. This is represented in the ordering information by the option code. There

are four available ranges, option codes 0, 1, 2 and 3. The option code corresponds with the two MSB of the

RG parameter. Each device is tested to meet the TempCo specification in the Sensitivity range determined

by the RG parameter (RG = 0…3, RG = 4…7, RG = 8...11 or RG = 12…15), regardless of the FG parameter.

The Sensitivity range is selected independently for Sensor A and Sensor B. Melexis may limit the available

combinations.

Option Code Rough Gain Sensitivity Range

(mV/mT)

Typical Magnetic Field Range

(mT, B

MAX

- B

MIN

)

0 0-3 (00 xx) 2.6 < S < 15 333 < B < 800

1 4-7 (01 xx) 10 < S < 35 156 < B < 333

2 8-11 (10 xx) 18 < S < 90 62 < B < 156

3 12-15 (11 xx) 50 < S < 210 6 < B < 62

Table 9: Optimized Sensitivity Range

The next figures show the typical Sensitivity versus the FG and RG parameters. The gray areas are

representative of the chip to chip dispersion (i.e.: for the same RG and FG parameters, the Sensitivity can

vary from chip to chip). There is large overlap between the different ranges for use of one range for

applications with large magnetic and/or mechanical dispersions. The Sensitivity graphs and tables can be

used to select the right device type for the application. If one is unsure of the application’s magnetic design

and the desired Sensitivity range Melexis recommends option code 2.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 10 of 21 Data Sheet

Rev 004 Nov/06

Sensitivity VS Fine Gain for RG = 8..11

MLX90277 SR2

Fine Gain

RG=8

RG=9

RG=10

RG=11

0 128 256 384 512 640 768 896 1023

100

120

140

Sensitivity Range 2

Sensitivity VS Fine Gain for RG = 4..7

MLX90277 SR1

Fine Gain

RG=4

RG=5

RG=6

RG=7

0 128 256 384 512 640 768 896 1023

Sensitivity Range 1

Sensitivity VS Fine Gain for RG = 0..3

MLX90277 SR0

Fine Gain

RG=0

RG=1

RG=2

RG=3

0 128 256 384 512 640 768 896 1023

2.5

7.5

12.5

17.5

22.5

Sensitivity Range 0

RG=12

RG=13

RG=14

RG=15

Sensitivity VS Fine Gain for RG = 12..15

MLX90277 SR3

Fine Gain

0 128 256 384 512 640 768 896 1023

120

160

200

240

280

320

Sensitivity Range 3

Figures 10.4-1…10.4-4 Sensitivity versus RG and FG

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 11 of 21 Data Sheet

Rev 004 Nov/06

10.5 Sensitivity Polarity (INVERT)

The slope transfer characteristic defines the Sensitivity. The INVERT parameter changes the Sensitivity's

polarity, or the slope's direction. This allows the device to accommodate the application requirements and

the magnet's polarity. The slope is inverted in the first stage of the IC, at the Hall Plate. With INVERT set to 0,

the output voltage increases as a South magnetic field is applied and decreases in the presence of a North

magnetic field. An INVERT value of 1 causes the output voltage to increase in the presence of a North

magnetic field and decrease in the presence of a South magnetic field. The magnetic field polarity is

referenced to the field component perpendicular to the top-face of the MLX90277.

10.6 Clamping Levels (CLAMPLOW, CLAMPHIGH)

Two independent values, called the clamping levels, can limit the output voltage range or swing. The

CLAMPLOW parameter adjusts the minimum output voltage level, ClampLo. The CLAMPHIGH sets the

maximum output voltage level, ClampHi. Both parameters have 10 bits of adjustment with a resolution of

approximately 0.005V. The formulas below give a close approximation of the output clamp voltage. The

actual clamping level formulas vary slightly from chip to chip. If CLAMPLOW exceeds CLAMPHIGH the

output voltage is fixed at the high clamp voltage level. The CLAMPHIGH and CLAMPLOW initial value of 768

for IC_A, set by Melexis, results in a fixed output voltage of approximately 76% V

. The CLAMPHIGH and

CLAMPLOW initial value of 256 for IC_B, set by Melexis, results in a fixed output voltage of approximately

25% V

CLAMPHIGH

ClampHi

CLAMPLOW

ClampLo

00.5

1023

10.5

1023

10.5

∗=

At the point the output voltage switches between the linear operating region and the clamping region the

output can deviate slightly. This is represented by the grey areas in the figure below. The limits for deviation

in the Y axis are listed in Table 10. The deviation in the X axis is calculated from the application's transfer

function. The Clamp Comparator Offset does not effect the output linearity or clamp voltage accuracy.

During calibration it is recommended to set the clamp voltage outside of the transition region (0V to 5V).

FIELD

CLAMP HIGH

CLAMP LOW

VOUT

Linear Operating

Region

Transition Point

Figure 10.6 Output Voltage Clamping Deviation

DC operating parameters at V

= 5V (unless otherwise specified) and for T

as specified by the temperature

range (E or L).

Parameter Symbol Test Conditions Min Typical

Max Units

Clamp Comparator Offset CLAMP

OFF

-40°C to 85°C - 0.7 + 0.7 %V

Table 10: Clamp Comparator Offset Specification

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 12 of 21 Data Sheet

Rev 004 Nov/06

10.7 Filter (FILTER)

Each die of the MLX90277 includes two programmable low-pass filters located within the chopper amplifier

stages. The two low-pass filters are controlled through a 4 bit parameter, FILTER. The FILTER value 0

corresponds to minimum filtering, maximum speed (impulse response time), and maximum output noise. The

value 15 provides the maximum filtering, minimum speed, and minimum output noise. It is important to note

the noise is also linked to the gain settings. The FILTER parameter needs to be adjusted to achieve optimal

performance. The next table shows typical values of the cut-off frequency at -3 dB versus FILTER and RG

parameters. FILTER values from 8 to 11 are not used. For most applications FILTER values 7 or 15 are

recommended.

Cut-off frequency at -3 dB (Hz) – Typical

Filter MLX90277 SR0

Rough Gain 0…3

MLX90277 SR1

Rough Gain 4…7

MLX90277 SR2

Rough Gain 8…11

MLX90277 SR3

Rough Gain 12…15

0 22900 14300 7000 3850

1 19500 11450 5550 2950

2 12300 10000 3000 2300

3 10400 6750 2100 1100

4 7450 3900 1500 850

5 5850 2900 1125 860

6 5700 2700 1350 715

7 5050 2550 1380 650

8 Not used

9 Not used

10 Not used

11 Not used

12 2200 840 565 250

13 1000 480 470 190

14 920 380 290 155

15 800 330 250 135

Table 11: Cut-off Frequency versus FILTER and RG Parameters

10.8 Sensitivity Temperature Compensation (TC, TCW, TC

)

The change in the device's Sensitivity versus temperature is defined as the Sensitivity Temperature

Compensation, TempCo. In an application the slope output transfer characteristic is often affected by

temperature. Fluctuations in temperature can cause variations in the air gap, mechanical alignment and

magnetic field. The Sensitivity Temperature Compensation feature compensates for these effects.

Three parameters, TC, TCW, TC

are used for adjustment of the TempCo. The TCW is used to adjust the

TempCo range, TC is for fine adjustment of the TempCo value, and TC

effects the TempCo linear response.

To simplify use of these parameters Melexis stores a look up table within the EEPROM of each device. The

look up table is optimized for each device by characterizing the unit over temperature at final test.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 13 of 21 Data Sheet

Rev 004 Nov/06

The value of TempCo is often determined by the magnet. In the application the TempCo is adjusted to

compensate for the temperature coefficient of the magnet. To adjust the value the look up table is read from

the device. The parameters are then calculated to match the desired value. The Melexis PTC hardware and

software tools contain built in functions for programming the TempCo.

TempCo Range (ppm / °C) Accuracy (ppm / °C)

0 to 500 ± 100

500 to 1200 ± 150

1200 to 2000 ± 200

Table 12: TempCo Accuracy

Note: The budget error of the whole system, the compensation mismatch (system vs. IC) tolerance should be

taken into consideration during the design. Table 11 is valid for Rough Gain within the specified option code.

See section 10.4 for information on selecting the option code.

10.9 Diagnostic Output Level (FAULTLEV)

The MLX90277 sensors' EEPROM memory content is secured through a parity check. This self-diagnostic

feature brings the output to a defined range in case of a parity error. The parameter, FAULTLEV, is used to

define the parity error diagnostic state. With the FAULTLEV set to 0 a parity error event will result in an

output diagnostic voltage low. With the FAULTLEV set to 1 a parity error event will result in an output

diagnostic voltage high. To get rid of the output load influence the output diagnostic voltage level can be

fixed to either Ground (to be used with pull-down load) or V

(to be used with pull-up load). Melexis PTC

software and hardware tools have built in functions for calculating and programming the parity.

Note: The MLX90277 sensors' EEPROM is also redundant. Each parameter bit is written in three separate

cells and a “majority voting” is applied to determine its status. A parity error is detected only if two out of the

three cells unexpectedly change state. The bits available for the customer ID are not redundant.

10.10 The EEPROM, Parity and Melexis CRC

The memory cells of the EEPROM are arranged in a table of four columns and one hundred twenty eight

rows. This configuration gives redundancy to the parameters stored in the EEPROM. Each parameter bit is

written in three separate cells in an individual row. A majority voting applied to the three cells determines the

logic status of the bit.

A parameter bit only toggles state in error if two out of three memory cells, within a row, unexpectedly

change. If this happens the feature, PARITY, forces the output voltage to the FAULTLEV diagnostic level.

This ensures the device does not operate with a critical memory fault.

The remaining memory cells are used for data storage. The status of these cells does not effect the device

operation. For example the Customer ID, CUSTID, is stored in this area. Melexis stores the device ID

information, TempCo look-up table and CRC bits in the extra cells. The CRC bits ensure the integrity of the

Melexis data.

Note: To avoid parity and CRC errors, the entire contents of the EEPROM must be read before

programming. Melexis PTC software and hardware tools have built in functions for reading the EEPROM and

handling parity.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 14 of 21 Data Sheet

Rev 004 Nov/06

10.11 Output Amplifier Configuration (MODE)

The output buffer can be configured to accommodate capacitive loads and improve the saturation voltage

(output swing). The two bit parameter, MODE, sets the current capacity of the output amplifier. Melexis sets

this parameter to 1 at final test. This parameter is not used by the end customer.

10.12 Memory Lock (MEMLOCK)

The Memory Lock feature prevents the device from entering programming mode and from any changes to the

EEPROM. The entire EEPROM is locked by setting the MEMLOCK parameter to 1. This should be the last

parameter set in the application.

10.13 IC traceability

A unique ID number is programmed into the EEPROM of every IC. The ID number gives Melexis additional

traceability to better service its customers. The ID number is composed of the lot number, wafer number and

wafer coordinates (X and Y). Memory is also available for the customer to add a serial number of the product

or any other data.

11 Performance Graphs

-10 0 10 20 30

-80

-60

-40

-20

Typical I

VS V

(Volts)

(mA)

4 4.5 5 5.5 6

4.5

5.5

6.5

7.5

8.5

Typical I

VS V

DDNOM

(Volts)

(mA)

150

-40

150

-40

DDNOM

Over Voltage

Under Voltage

Figure 11-1…11-2 I

versus V

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 15 of 21 Data Sheet

Rev 004 Nov/06

12 Applications Information

12.1 Application Circuits

The TEST pins are not used in applications. For EMC protection it is recommended to connect the TEST

pins to Ground as close as possible to the device pins. The values for capacitors, C11, C12, C21 and C22,

can be adjusted to satisfy ESD and EMC requirements according to the environment. Ceramic capacitors

are recommended for use in the application. However for stable operation, C12 and C21 should each not be

higher than 150nF. If higher capacitors (due to special ESD or EMC requirements) or special circuit

configurations are requested, please contact Melexis.

The MLX90277 can operate with a high impedance load; a load resistor is not required.

Figures 12.1-1…12.1-2 Application Circuits

A voltage of 9V is required on V

for programming. All additional components connected to V

must be

able to withstand the voltage.

The MLX90277 is designed for operation with a stable 5V supply. If fast voltage transients occur additional

filtering may be required.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 16 of 21 Data Sheet

Rev 004 Nov/06

12.2 Programming the Sensor

To program the individual MLX90277 sensors, connection to V

, GND, and V

OUT

is required. The device is

placed into program mode by increasing the supply voltage to the V

program level. In program mode data

is clocked into the device through the output pin using the Melexis tri-level PTC protocol. The clock and data

are integrated into one serial data stream, eliminating the need for a dedicated clock signal. The data is

clocked at the leading edge of each bit.

Figure 12.2-1 V

Programming Level

2.5V

5.0V

Device

Decoded

Clock

Device

Decoded

Data

X XX

VOUT

Program Wave Form

Figure 12.2-2 Tri-Level PTC

Note: External capacitors and resistors will effect the rise and fall times for the programming waveforms.

Program pulse timings may require adjustment for the application. The device can not be programmed if

MEMLOCK equals 1.

The EEPROM contents can be read from the device. This procedure, known as a read back, is done by

sending a read command and then measuring the supply current. To successfully read the EEPROM it must

be possible to measure the supply current to the device. The Melexis PTC hardware and software tools

contain built in functions for reading the EEPROM.

The MLX90277 sensors can be programmed by using the PTC-04 programmer and the dedicated software

tools. The timing and voltage levels are controlled through the programming hardware and software. Further

details can be found in the MLX90277 software documentation.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 17 of 21 Data Sheet

Rev 004 Nov/06

12.3 Calibration Procedure

The programmable features of the device allow it to be calibrated within the application. This section gives

general information for a two point calibration procedure. The two point calibration is the most common,

however, it is possible to adapt other procedures.

1.) The first step in the calibration procedure is to initialize the device. This is done by establishing

communication and reading the contents of the EEPROM.

2.)The second step is to set the TempCo and FILTER settings.

3.) Step three is the evaluation of position one. During this step the output voltage is measured with initial

values for RG, FG and OFFSET.

4.) Step four is the evaluation of position two. During this step, the output voltage is measured with the same

values from step 3. From the measurements it is possible to calculate the slope and offset error. Next the

output slope transfer characteristic versus FG and RG is interpolated. With this information the initial settings

are adjusted and the output voltage is measured again.

5.) Step five is the final check and adjustment. At this stage small corrections are made to the OFFSET and

FG parameters. Next, the output clamping parameters, CLAMPHIGH and CLAMPLOW, are determined.

6.) The sixth step is the program phase. Now that all the parameters are determined and the application

requirements are satisfied, the settings are programmed into the EEPROM.

7.) The final step, seven, is the lock and verify step. Here the customer can perform any number of additional

measurements and verify the EEPROM contents. After this is completed the MEMLOCK is set and the

EEPROM is locked, preventing any further programming.

Note: EEPROM verification is done by reading the contents of the EEPROM and comparing it to the data

written. It is possible to read the EEPROM contents regardless of the status of MEMLOCK.

The Melexis PTC software tools contain built in functions and procedures for calibrating the MLX90277.

Please refer to the software documentation for more information on how to use the calibration tools.

The outputs of the MLX90277 are ratiometric. To avoid calibration errors from fluctuations in the supply

voltage, the output voltage should be measured as a percentage of the supply voltage.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 18 of 21 Data Sheet

Rev 004 Nov/06

13 Standard information regarding manufacturability of Melexis

products with different soldering processes

Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity

level according to following test methods:

Reflow Soldering SMD’s (Surface Mount Devices)

• IPC/JEDEC J-STD-020

Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices

(classification reflow profiles according to table 5-2)

• EIA/JEDEC JESD22-A113

Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing

(reflow profiles according to table 2)

Wave Soldering SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)

• EN60749-20

Resistance of plastic- encapsulated SMD’s to combined effect of moisture and soldering heat

• EIA/JEDEC JESD22-B106 and EN60749-15

Resistance to soldering temperature for through-hole mounted devices

Iron Soldering THD’s (Through Hole Devices)

• EN60749-15

Resistance to soldering temperature for through-hole mounted devices

Solderability SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)

• EIA/JEDEC JESD22-B102 and EN60749-21

Solderability

For all soldering technologies deviating from above mentioned standard conditions (regarding peak

temperature, temperature gradient, temperature profile etc) additional classification and qualification tests

have to be agreed upon with Melexis.

The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of

adhesive strength between device and board.

Melexis is contributing to global environmental conservation by promoting lead free solutions. For more

information on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Of

the use of certain Hazardous Substances) please visit the quality page on our website:

http://www.melexis.com/quality.asp

14 ESD Precautions

Electronic semiconductor products are sensitive to Electro Static Discharge (ESD).

Always observe Electro Static Discharge control procedures whenever handling semiconductor products.

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 19 of 21 Data Sheet

Rev 004 Nov/06

15 Package Information

The TSSOP14 package is lead-free and is released for MSL3/260°C.

15.1 Package Dimensions

0.09

0.20

6.4 TYP

4.30

4.50**

0.65 TYP

1.0 DIA

1.0

NOTES:

All dimensions are in millimeters (anlges in degrees).

* Dimension does not include mold flash, protrusions or gate burrs (shall not exceed 0.15 per side).

** Dimension does not include interleads flash or protrusion (shall not exceed 0.25 per side).

*** Dimension does not include dambar protrusion. Allowable dambar protrusion shall be 0.08 mm total in excess of the dimension at

maximum material condition. Dambar cannot be located on the lower radius of the foot.

4.90

5.10*

1.1 MAX

0.05

0.15

0.85

0.95

0.19

0.30***

0.20 TYP

TYP

0.09 MIN

0.50

0.75

1.0 TYP

TYP

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 20 of 21 Data Sheet

Rev 004 Nov/06

15.2 Pin-out and Marking

15.3 Hall Plate Positioning

0.003

0.103

0.641

0.741

0.641

0.741

0.003

0.103

MLX90277

Hall plate 1 Hall plate 2

0.240

0.360

MLX90277

Dual Programmable Linear Hall Effect Sensor

3901090277 Page 21 of 21 Data Sheet

Rev 004 Nov/06

16 Disclaimer

Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its

Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the

information set forth herein or regarding the freedom of the described devices from patent infringement.

Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior

to designing this product into a system, it is necessary to check with Melexis for current information. This

product is intended for use in normal commercial applications. Applications requiring extended temperature

range, unusual environmental requirements, or high reliability applications, such as military, medical life-

support or life-sustaining equipment are specifically not recommended without additional processing by

Melexis for each application.

The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be

liable to recipient or any third party for any damages, including but not limited to personal injury, property

damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential

damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical

data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis’ rendering

of technical or other services.

For the latest version of this document, go to our website at

www.melexis.com

Or for additional information contact Melexis Direct:

Europe, Africa, Asia: America:

Phone: +32 1367 0495 Phone: +1 603 223 2362

E-mail: sales_europe@melexis.com E-mail: sales_usa@melexis.com

ISO/TS 16949 and ISO14001 Certified