Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type: B43086
Date: December 2010
© EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Long-life grade capacitors for professional applications
Applications
Electronic ballast applications
Energy saving lamps
Power supplies
Features
RoHS-compatible
High ripple current
High reliability
Useful life of 10000 h at 105 °C
Construction
Radial leads
Aluminum case, fully insulated
Charge-discharge proof
Minus pole marking on the insulating sleeve
Case with safety vent
Delivery mode
Bulk
Taped, Ammo pack
Cut (see chapter "Single-ended Taping, packing and lead
configurations, Cut leads (Chapter A)")
Kinked (see chapter "Single-ended Taping, packing and
lead configurations, Kinked leads (Chapter A)")
Refer to chapter "Single-ended capacitors Taping, packing
and lead configurations" for further details.
Single-ended capacitors B43086
High temperature 105 °C
Page 2 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Specifications and characteristics in brief
Rated voltage VR200 ... 450 V DC
Surge voltage VSVR≤250 V DC: 1.15 VR(at room temperature)
VR> 250 V DC: 1.1 VR(at room temperature)
Rated capacitance CR1.0 ... 100 µF
Capacitance tolerance ±20% M
Dissipation factor (max.)
(20 °C, 120 Hz)
VR(V DC) 200 250 350 400 450
tan δ0.15 0.15 0.15 0.20 0.24
Leakage current Ileak
(20 °C, after 5 minutes)
Useful life
105 °C; VR; IAC,R > 10000 h
Requirements ∆C/C ≤ ±20% of initial value
tan δ ≤ 2 times initial specified limit
Ileak ≤initial specified limit
Shelf life After storage for 1000 h at 105 °C, the capacitors shall meet the
requirement of load life test after reforming process. After test: VR
to be applied for 30 minutes, 24 to 48 hours before measurement.
Low temperature stability
(impedance ratio)
(120 Hz)
VR(V DC) 200 250 350 400 450
33468
Vibration resistance test To IEC 60068-2-6, test Fc:
Frequency range 10 ... 55 Hz, displacement amplitude 0.75 mm,
acceleration max. 10 g, duration 3 ×2 h.
If can size D <16 mm, capacitor is mounted by the leads
If can size D ≥16 mm, capacitor rigidly clamped by the aluminum
case
IEC climatic category To IEC 60068-1:
25/105/56 (25 °C/+105 °C/56 days damp heat test)
B43086
High temperature 105 °C
Page 3 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawing
Case Dimensions
d×l
mm
dmax ×lmax
mm
a
mm
b
mm
10 ×12.5 11.0 ×13.0 5.0 ±0.5 0.6 ±0.1
10 ×16 11.0 ×17.5 5.0 ±0.5 0.6 ±0.1
10 ×20 11.0 ×22.0 5.0 ±0.5 0.6 ±0.1
12.5 ×20 13.5 ×22.0 5.0 ±0.5 0.6 ±0.1
12.5 ×25 13.5 ×27.0 5.0 ±0.5 0.6 ±0.1
16 ×20 17.0 ×22.0 7.5 ±0.5 0.8 ±0.1
16 ×25 17.0 ×27.0 7.5 ±0.5 0.8 ±0.1
16 ×31.5 17.0 ×33.5 7.5 ±0.5 0.8 ±0.1
B43086
High temperature 105 °C
Page 4 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types
VR(V DC) 200 250 350 400 450
Case dimensions d ×l (mm)
CR(µF)
1.0 10 ×12.5
1.5 10 ×12.5
2.2 10 ×12.5
3.3 10 ×16
4.7 10 ×12.5 10 ×16 10 ×20
5.6 10 ×16 10 ×20 10 ×20
6.8 10 ×12.5 10 ×16 10 ×20 10 ×20
10 10 ×16 10 ×16 10 ×20 12.5 ×20 12.5 ×20
15 10 ×20 10 ×20 12.5 ×20 12.5 ×25
22 10 ×20 12.5 ×20 12.5 ×25 12.5 ×25 16 ×25
33 12.5 ×20 12.5 ×25 16 ×20 16 ×25 16 ×31.5
47 12.5 ×20 16 ×20 16 ×25 16 ×31.5
68 12.5 ×25 16 ×25
82 16 ×20 16 ×31.5
100 16 ×25
B43086
High temperature 105 °C
Page 5 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz, 20 °C
µF
Case dimensions
d×l
mm
IAC,R
100 kHz, 105 °C
mA
Ordering code
(composition see below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for ∅10 ... 12.5 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for ∅16 mm)
VR= 200 V DC
10 10 ×16 200 B43086A2106M***
15 10 ×20 320 B43086A2156M***
22 10 ×20 400 B43086A2226M***
33 12.5 ×20 480 B43086A2336M***
47 12.5 ×20 528 B43086A2476M***
68 12.5 ×25 608 B43086A2686M***
82 16 ×20 720 B43086A2826M***
100 16 ×25 880 B43086A2107M***
VR= 250 V DC
6.8 10 ×12.5 176 B43084F2685M***
10 10 ×16 208 B43086F2106M***
15 10 ×20 320 B43086F2156M***
22 12.5 ×20 456 B43086F2226M***
33 12.5 ×25 520 B43086F2336M***
47 16 ×20 576 B43086F2476M***
68 16 ×25 800 B43086F2686M***
82 16 ×31.5 880 B43086F2826M***
VR= 350 V DC
4.7 10 ×12.5 120 B43086A4475M***
5.6 10 ×16 136 B43086A4565M***
6.8 10 ×16 176 B43086A4685M***
10 10 ×20 208 B43086A4106M***
22 12.5 ×25 280 B43086A4226M***
33 16 ×20 400 B43086A4336M***
47 16 ×25 520 B43086A4476M***
B43086
High temperature 105 °C
Page 6 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz, 20 °C
µF
Case dimensions
d×l
mm
IAC,R
100 kHz, 105 °C
mA
Ordering code
(composition see below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk
002 = for cut leads, bulk
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for ∅10 ... 12.5 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for ∅16 mm)
VR= 400 V DC
1 10 ×12.5 56 B43086A9105M***
1.5 10 ×12.5 68 B43086A9155M***
2.2 10 ×12.5 80 B43086B9225M***
3.3 10 ×16 104 B43086B9335M***
4.7 10 ×16 144 B43086B9475M***
5.6 10 ×20 160 B43086A9565M***
6.8 10 ×20 176 B43086B9685M***
10 12.5 ×20 200 B43086B9106M***
15 12.5 ×20 280 B43086A9156M***
22 12.5 ×25 320 B43086A9226M***
33 16 ×25 480 B43086A9336M***
47 16 ×31.5 640 B43086A9476M***
VR= 450 V DC
4.7 10 ×20 100 B43086A5475M***
5.6 10 ×20 112 B43086A5565M***
6.8 10 ×20 120 B43086A5685M***
10 12.5 ×20 240 B43086A5106M***
15 12.5 ×25 320 B43086A5156M***
22 16 ×25 440 B43086A5226M***
33 16 ×31.5 560 B43086A5336M***
B43086
High temperature 105 °C
Page 7 of 31Please read Cautions and warnings and
Important notes at the end of this document.
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Useful life
depending on ambient temperature TAunder ripple current operating conditions1)
Frequency factor of permissible ripple current IAC versus frequency f
B43086
High temperature 105 °C
Page 8 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 18 mm as follows:
Lead spacing F = 2.0 mm (∅d=4 … 5 mm)
Lead spacing F = 2.5 mm (∅d=4 … 6.3 mm)
Lead spacing F = 3.5 mm (∅d = 8 mm)
Lead spacing F = 5.0 mm (∅d=4 … 12.5 mm)
Lead spacing F = 7.5 mm (∅d = 16 ... 18 mm).
Lead spacing 2.0 mm (∅d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆h D0
4 ... 5 2.0 18.5 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
B43086
High temperature 105 °C
Page 9 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 2.5 mm (∅d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
∅d F H W W0W1W2H0P P0P1I1t∆h D0
4 ... 6.3 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
Toler-
rance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
Lead spacing 3.5 mm (∅d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆h D0
8 3.5 18.5 18.0 10 9.0 3.0 12.7 12.7 4.6 1.0 0.7 1.0 4.0
Toler-
ance
+0.8
0.2 ±1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.6 max. ±0.2 max. ±0.2
Leads can also run straight through the taping area. Taping is available up to dimensions
d×l=8×15 mm.
B43086
High temperature 105 °C
Page 10 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 5.0 mm (∅d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (∅d = 10 ... 12.5 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
∅d F H W W0W1W2H0P P0P1I1t∆h D0
4 ...
6.3 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.6 1.0 4.0
820.0 10.0 16.0 12.7 12.7 3.85
10 5.0 19.0 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.6 1.0 4.0
12.5 19.0 12.5 15.0 15.0 5.0
Toler-
ance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. +0.3
0.2 max. ±0.2
Taping is available up to dimensions d ×l=10×31.5 mm and 12.5 ×25 mm.
Taping is not available for d ×l=8×20 mm.
B43086
High temperature 105 °C
Page 11 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 7.5 mm (∅d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆P∆h D0
16 7.5 18.5 18.0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0
18
Toler-
ance ±0.8 0.5
+0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2
Taping is available up to dimensions d ×l=16×31.5 mm and 18 ×31.5 mm.
B43086
High temperature 105 °C
Page 12 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Cut or kinked leads
Single-ended capacitors are available with cut or kinked leads. Other lead configurations also
available upon request.
Cut leads (Chapter A)
Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086,
B43088, B43827, B43828.
Last 3 digits of ordering code: 002
Case size d x l (mm) Dimensions
(mm)
a±0.5
4 x 7 1.5
5 x 7 2.0
5 x 11 2.0
6.3 x 7 2.5
6.3 x 11 2.5
8 x 7 3.5
8 x 11.5 3.5
8 x 15 3.5
8 x 20 3.5
10 x 12.5 5.0
10 x 16 5.0
10 x 20 5.0
10 x 25 5.0
10 x 31.5 5.0
Case size d x l (mm) Dimensions
(mm)
a±0.5
12.5 x 16 5.0
12.5 x 20 5.0
12.5 x 25 5.0
12.5 x 31.5 5.0
12.5 x 35.5 5.0
12.5 x 40 5.0
16 x 20 7.5
16 x 25 7.5
16 x 31.5 7.5
16 x 35.5 7.5
16 x 40 7.5
18 x 20 7.5
18 x 25 7.5
18 x 31.5 7.5
18 x 35.5 7.5
18 x 40 7.5
B43086
High temperature 105 °C
Page 13 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Cut leads (Chapter B)
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Last 3 digits of ordering code: 002
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×12.5 5.0
10 ×16 5.0
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
16 ×35.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B43086
High temperature 105 °C
Page 14 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Kinked leads (Chapter A)
Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086,
B43088, B43827, B43828.
Last 3 digits of ordering code: 001
Case size d x l (mm) Dimensions
(mm)
a±0.5
4 x 7 1.5
5 x 7 2.0
5 x 11 2.0
6.3 x 7 2.5
6.3 x 11 2.5
8 x 7 3.5
8 x 11.5 3.5
8 x 15 3.5
8 x 20 3.5
10 x 12.5 5.0
10 x 16 5.0
10 x 20 5.0
10 x 25 5.0
10 x 31.5 5.0
Case size d x l (mm) Dimensions
(mm)
a±0.5
12.5 x 16 5.0
12.5 x 20 5.0
12.5 x 25 5.0
12.5 x 31.5 5.0
12.5 x 35.5 5.0
12.5 x 40 5.0
16 x 20 7.5
16 x 25 7.5
16 x 31.5 7.5
16 x 35.5 7.5
16 x 40 7.5
18 x 20 7.5
18 x 25 7.5
18 x 31.5 7.5
18 x 35.5 7.5
18 x 40 7.5
B43086
High temperature 105 °C
Page 15 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Kinked leads (Chapter B)
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Last 3 digits of ordering code: 001
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
16 ×35.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B43086
High temperature 105 °C
Page 16 of 31Please read Cautions and warnings and
Important notes at the end of this document.
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 18 mm.
There are three configurations available: Crimped leads, J leads, bent 90°leads
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal With flat rubber seal
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 a ±0.5 ∅b
16 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×35.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
18 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
B43086
High temperature 105 °C
Page 17 of 31Please read Cautions and warnings and
Important notes at the end of this document.
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 J ±0.2 a ±0.5 ∅b
10 ×12.5 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×16 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×25 3.2 0.7 1.2 5.0 0.6 ±0.05
16 ×20 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×25 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×35.5 3.5 0.7 1.6 7.5 0.8 ±0.05
18 ×20 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×25 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×35 3.5 0.7 1.6 7.5 0.8 ±0.1
B43086
High temperature 105 °C
Page 18 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Bent 90°leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 ∅b
16 ×20 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×25 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×31.5 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×35.5 4.0 4.0 12.0 7.5 0.8 ±0.05
18 ×20 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×25 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×31.5 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×35 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×40 4.0 4.0 13.0 7.5 0.8 ±0.1
Bent leads for diameter 12.5 mm available upon request.
B43086
High temperature 105 °C
Page 19 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Packing units and box dimensions
Ammo pack
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
4×7 330 50 196 2000
5×7 330 50 226 2000
5×11 330 50 226 2000
6.3 ×7 330 50 286 2000
6.3 ×11 330 50 286 2000
8×7 330 50 246 1000
8×11.5 330 50 246 1000
8×15 330 50 246 500
10 ×12.5 330 50 196 500
10 ×16 330 54 196 500
10 ×20 330 58 196 500
12.5 ×20 341 60 272 500
12.5 ×25 341 65 272 500
16 ×25 320 65 270 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B43086
High temperature 105 °C
Page 20 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Ammo pack
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
8×11.5 345 55 240 1000
10 ×12.5 345 55 280 750
10 ×16 345 60 200 500
10 ×20 345 60 200 500
12.5 ×20 345 65 280 500
12.5 ×25 345 65 280 500
16 ×20 315 65 275 300
16 ×25 315 65 275 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B43086
High temperature 105 °C
Page 21 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 4 x 7 ... 16 x 40
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
dxl
mm
Standard,
bulk
pcs.
Taped,
Ammo pack
pcs.
Kinked leads,
bulk
pcs.
Cut leads,
bulk
pcs.
4 x 7 10000 2000 15000 15000
5 x 7 7500 2000 10000 10000
5 x 11 5000 2000 10000 10000
6.3 x 7 5000 2000 10000 10000
6.3 x 11 5000 2000 5000 5000
8 x 7 5000 1000 5000 5000
8 x 11.5 2500 1000 4000 4000
8 x 15 2000 1000 2500 2500
8 x 20 1500 2000 2000
10 x 12.5 2000 500 2500 2500
10 x 16 1500 500 2000 2000
10 x 20 1000 500 1500 1500
10 x 25 1000 500 1250 1250
12.5 x 16 750 500 1000 1000
12.5 x 20 750 500 500 500
12.5 x 25 750 500 500 500
12.5 x 31.5 500 750 750
12.5 x 35.5 500 750 750
12.5 x 40 500 750 750
16 x 20 375 300 500 500
16 x 25 375 300 500 500
16 x 31.5 250 300 375 375
16 x 35.5 250 375 375
16 x 40 250 375 375
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002
006
007
008
009
016
3.5
2.5
5.0
7.5
2.0
8
4 ... 6.3
4 ... 12.5
16 ... 18
4 ... 5
B43086
High temperature 105 °C
Page 22 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 x 20 ... 18 x 40
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
dxl
mm
Standard,
bulk
pcs.
Taped,
Ammo pack
pcs.
Kinked leads,
bulk
pcs.
Cut leads,
bulk
pcs.
18 x 20 250 250 100 100
18 x 25 250 250 100 100
18 x 31.5 250 250 100 100
18 x 35.5 250 100 100
18 x 40 250 100 100
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002
009 7.5 16 ... 18
B43086
High temperature 105 °C
Page 23 of 31Please read Cautions and warnings and
Important notes at the end of this document.
1) Available upon request
Overview of packing units and code numbers for case sizes 8 ×11.5 ... 16 ×35.5
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
8×11.5 1000 1000
10 ×12.5 1000 750 1000 675
10 ×16 1000 500 1000 675
10 ×20 500 500 500 500 500
12.5 ×20 350 500 350 350 300 1)
12.5 ×25 250 500 500 500 225 1)
12.5 ×30 200
12.5 ×35 175
12.5 ×40 175
16 ×20 250 300 200 200 200 200 120
16 ×25 250 300 200 200 200 200 120
16 ×31.5 200 300 250 250 344 344 120
16 ×35.5 100 100 100 150 150 150
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
006
008
009
3.5
5
7.5
8
5...12.5
16...18
B43086
High temperature 105 °C
Page 24 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 ×20 ... 18 ×40
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
18 ×20 175 250 175 175 200 200 120
18 ×25 150 250 150 150 200 200 120
18 ×31.5 100 250 100 100 150 150 120
18 ×35 100 100 100 150 150 150
18 ×40 125 100 100 120 72
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
009 7.5 16...18
B43086
High temperature 105 °C
Page 25 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling aluminum electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
B43086
High temperature 105 °C
Page 26 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Product safety
The table below summarizes the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic Safety information Reference
chapter "General
technical information"
Polarity Make sure that polar capacitors are connected
with the right polarity.
1
"Basic construction of
aluminum electrolytic
capacitors"
Reverse voltage Voltages polarity classes should be prevented by
connecting a diode.
3.1.6
"Reverse voltage"
Upper category
temperature
Do not exceed the upper category temperature. 7.2
"Maximum permissible
operating temperature"
Maintenance Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
10
"Maintenance"
Mounting
position of screw-
terminal capacitors
Do not mount the capacitor with the terminals
(safety vent) upside down.
11.1.
"Mounting positions of
capacitors with screw
terminals"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
11.4
"Mounting
considerations for
single-ended capacitors"
Robustness of
terminals
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
11.3
"Mounting torques"
Soldering Do not exceed the specified time or temperature
limits during soldering.
11.5
"Soldering"
B43086
High temperature 105 °C
Page 27 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Topic Safety information Reference
chapter "General
technical information"
Soldering,
cleaning agents
Do not allow halogenated hydrocarbons to come
into contact with aluminum electrolytic capacitors.
11.6
"Cleaning agents"
Passive
flammability
Avoid external energy, such as fire or electricity. 8.1
"Passive flammability"
Active
flammability
Avoid overload of the capacitors. 8.2
"Active flammability"
Reference
chapter "Capacitors with
screw terminals"
Breakdown strength
of insulating
sleeves
Do not damage the insulating sleeve, especially
when ring clips are used for mounting.
"Screw terminals
accessories"
B43086
High temperature 105 °C
Page 28 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Symbols and terms
Symbol English German
C Capacitance Kapazität
CRRated capacitance Nennkapazität
CSSeries capacitance Serienkapazität
CS,T Series capacitance at temperature T Serienkapazität bei Temperatur T
CfCapacitance at frequency f Kapazität bei Frequenz f
d Case diameter, nominal dimension Gehäusedurchmesser, Nennmaß
dmax Maximum case diameter Maximaler Gehäusedurchmesser
ESL Self-inductance Eigeninduktivität
ESR Equivalent series resistance Ersatzserienwiderstand
ESRfEquivalent series resistance at
frequency f
Ersatzserienwiderstand bei Frequenz f
ESRTEquivalent series resistance at
temperature T
Ersatzserienwiderstand bei Temperatur T
f Frequency Frequenz
I Current Strom
IAC Alternating current (ripple current) Wechselstrom
IAC,rms Root-mean-square value of alternating
current
Wechselstrom, Effektivwert
IAC,f Ripple current at frequency f Wechselstrom bei Frequenz f
IAC,max Maximum permissible ripple current Maximal zulässiger Wechselstrom
IAC,R Rated ripple current Nennwechselstrom
IAC,R (B) Rated ripple current for base cooling Nennwechselstromstrom für Bodenkühlung
Ileak Leakage current Reststrom
Ileak,op Operating leakage current Betriebsreststrom
l Case length, nominal dimension Gehäuselänge, Nennmaß
lmax Maximum case length (without
terminals and mounting stud)
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
R Resistance Widerstand
Rins Insulation resistance Isolationswiderstand
Rsymm Balancing resistance Symmetrierwiderstand
T Temperature Temperatur
∆T Temperature difference Temperaturdifferenz
TAAmbient temperature Umgebungstemperatur
TCCase temperature Gehäusetemperatur
TBCapacitor base temperature Temperatur des Becherbodens
t Time Zeit
∆t Period Zeitraum
tbService life (operating hours) Brauchbarkeitsdauer (Betriebszeit)
B43086
High temperature 105 °C
Page 29 of 31Please read Cautions and warnings and
Important notes at the end of this document.
Symbol English German
V Voltage Spannung
VFForming voltage Formierspannung
Vop Operating voltage Betriebsspannung
VRRated voltage, DC voltage Nennspannung, Gleichspannung
VSSurge voltage Spitzenspannung
XCCapacitive reactance Kapazitiver Blindwiderstand
XLInductive reactance Induktiver Blindwiderstand
Z Impedance Scheinwiderstand
ZTImpedance at temperature T Scheinwiderstand bei Temperatur T
tan δDissipation factor Verlustfaktor
λFailure rate Ausfallrate
ε0Absolute permittivity Elektrische Feldkonstante
εrRelative permittivity Dielektrizitätszahl
ωAngular velocity; 2 πf Kreisfrequenz; 2 πf
Note
All dimensions are given in mm.
B43086
High temperature 105 °C
Page 30 of 31Please read Cautions and warnings and
Important notes at the end of this document.
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-
tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the "General Terms of Delivery for Products and Services in the Electrical In-
dustry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap,
DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKK, MKD, MLSC, MotorCap, PCC,
PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trade-
marks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
Important notes
Page 31 of 31
