SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 D 15-V Digital or 7.5-V Peak-to-Peak D D D D D D D D D Matched Control-Input to Signal-Output Switching 125- Typical On-State Resistance for 15-V Operation Switch On-State Resistance Matched to Within 5 Over 15-V Signal-Input Range On-State Resistance Flat Over Full Peak-to-Peak Signal Range High On/Off Output-Voltage Ratio: 80 dB Typical at fis = 10 kHz, RL = 1 k High Degree of Linearity: <0.5% Distortion Typical at fis = 1 kHz, Vis = 5 V p-p, VDD - VSS 10 V, RL = 10 k Extremely Low Off-State Switch Leakage, Resulting in Very Low Offset Current and High Effective Off-State Resistance: 10 pA Typical at VDD - VSS = 10 V, TA = 25C Extremely High Control Input Impedance (Control Circuit Isolated From Signal Circuit): 1012 Typical Low Crosstalk Between Switches: -50 dB Typical at fis = 8 MHz, RL = 1 k D D D D D Capacitance: Reduces Output Signal Transients Frequency Response, Switch On = 40 MHz Typical 100% Tested for Quiescent Current at 20 V 5-V, 10-V, and 15-V Parametric Ratings Meets All Requirements of JEDEC Tentative Standard No. 13-B, Standard Specifications for Description of "B" Series CMOS Devices Applications: - Analog Signal Switching/Multiplexing: Signal Gating, Modulator, Squelch Control, Demodulator, Chopper, Commutating Switch - Digital Signal Switching/Multiplexing - Transmission-Gate Logic Implementation - Analog-to-Digital and Digital-to-Analog Conversion - Digital Control of Frequency, Impedance, Phase, and Analog-Signal Gain E, F, M, NS, OR PW PACKAGE (TOP VIEW) SIG A IN/OUT SIG A OUT/IN SIG B OUT/IN SIG B IN/OUT CONTROL B CONTROL C VSS 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VDD CONTROL A CONTROL D SIG D IN/OUT SIG D OUT/IN SIG C OUT/IN SIG C IN/OUT description/ordering information The CD4066B is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals. It is pin-for-pin compatible with the CD4016B, but exhibits a much lower on-state resistance. In addition, the on-state resistance is relatively constant over the full signal-input range. The CD4066B consists of four bilateral switches, each with independent controls. Both the p and the n devices in a given switch are biased on or off simultaneously by the control signal. As shown in Figure 1, the well of the n-channel device on each switch is tied to either the input (when the switch is on) or to VSS (when the switch is off). This configuration eliminates the variation of the switch-transistor threshold voltage with input signal and, thus, keeps the on-state resistance low over the full operating-signal range. The advantages over single-channel switches include peak input-signal voltage swings equal to the full supply voltage and more constant on-state impedance over the input-signal range. However, for sample-and-hold applications, the CD4016B is recommended. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated !" #!$% &"' &! #" #" (" " ") !" && *+' &! #", &" ""%+ %!&" ", %% #""' POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 description/ordering information (continued) ORDERING INFORMATION -55C to 125C ORDERABLE PART NUMBER PACKAGE TA TOP-SIDE MARKING CDIP - F Tube of 25 CD4066BF3A CD4066BF3A PDIP - E Tube of 25 CD4066BE CD4066BE Tube of 50 CD4066BM Reel of 2500 CD4066BM96 Reel of 250 CD4066BMT Reel of 2000 CD4066BNSR Tube of 90 CD4066BPW Reel of 2000 CD4066BPWR SOIC - M SOP - NS TSSOP - PW CD4066BM CD4066B CM066B Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Switch Control In Vis p n p n Control VC Out Vos n VSS VDD VSS All control inputs are protected by the CMOS protection network. NOTES: A. All p substrates are connected to VDD. B. Normal operation control-line biasing: switch on (logic 1), VC = VDD; switch off (logic 0), VC = VSS C. Signal-level range: VSS Vis VDD 92CS-29113 Figure 1. Schematic Diagram of One-of-Four Identical Switches and Associated Control Circuitry 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 absolute maximum ratings over operating free-air temperature (unless otherwise noted) DC supply-voltage range, VDD (voltages referenced to VSS terminal) . . . . . . . . . . . . . . . . . . . . -0.5 V to 20 V Input voltage range, Vis (all inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VDD + 0.5 V DC input current, IIN (any one input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA Package thermal impedance, JA (see Note 1): E package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W M package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113C/W Lead temperature (during soldering): At distance 1/16 1/32 inch (1,59 0,79 mm) from case for 10 s max . . . . . . . . . . . . . . . . . . . . . . . 265C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions MIN VDD TA Supply voltage Operating free-air temperature POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MAX UNIT 3 18 V -55 125 C 3 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 electrical characteristics LIMITS AT INDICATED TEMPERATURES PARAMETER IDD TEST CONDITIONS Quiescent device current VIN (V) VDD (V) UNIT 25C -55C -40C 85C 125C TYP MAX 0, 5 5 0.25 0.25 7.5 7.5 0.01 0.25 0, 10 10 0.5 0.5 15 15 0.01 0.5 0, 15 15 1 1 30 30 0.01 1 0, 20 20 5 5 150 150 0.02 5 5 800 850 1200 1300 470 1050 10 310 330 500 550 180 400 15 200 210 300 320 125 240 A A Signal Inputs (Vis) and Outputs (Vos) ron On-state resistance (max) VC = VDD, RL = 10 k returned V DD * V SS to , 2 Vis = VSS to VDD ron THD Iis 4 15 10 10 15 5 On-state resistance difference between any two switches RL = 10 k, VC = VDD Total harmonic distortion VC = VDD = 5 V, VSS = -5 V, Vis(p-p) = 5 V (sine wave centered on 0 V), RL = 10 k, fis = 1-kHz sine wave 0.4 % -3-dB cutoff frequency (switch on) VC = VDD = 5 V, VSS = -5 V, Vis(p-p) = 5 V (sine wave centered on 0 V), RL = 1 k 40 MHz -50-dB feedthrough frequency (switch off) VC = VSS = -5 V, Vis(p-p) = 5 V (sine wave centered on 0 V), RL = 1 k 1 MHz Input/output leakage current (switch off) (max) VC = 0 V, Vis = 18 V, Vos = 0 V; and VC = 0 V, Vis = 0 V, Vos = 18 V VC(A) = VDD = 5 V, VC(B) = VSS = -5 V, Vis(A) = 5 Vp-p, 50- source, RL = 1 k -50-dB crosstalk frequency tpd 5 Propagation delay (signal input to signal output) Cis Input capacitance Cos Cios RL = 200 k, VC = VDD, VSS = GND, CL = 50 pF, Vis = 10 V (square wave centered on 5 V), tr, tf = 20 ns 18 0.1 0.1 1 1 10-5 0.1 8 A MHz 5 20 40 10 10 20 15 7 15 ns 8 pF Output capacitance VDD = 5 V, VC = VSS = -5 V VDD = 5 V, VC = VSS = -5 V 8 pF Feedthrough VDD = 5 V, VC = VSS = -5 V 0.5 pF POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 electrical characteristics (continued) LIMITS AT INDICATED TEMPERATURES CHARACTERISTIC TEST CONDITIONS UNIT 25C VDD (V) -55C -40C 85C 125C TYP MAX Control (VC) VILC Control input, low voltage (max) |Iis| < 10 A, Vis = VSS, VOS = VDD, and Vis = VDD, VOS = VSS 5 1 1 1 1 1 10 2 2 2 2 2 15 2 2 2 2 2 5 VIHC IIN Control input, high voltage 3.5 (MIN) 10 7 (MIN) 15 11 (MIN) V Input current (max) Vis VDD, VDD - VSS = 18 V, VCC VDD - VSS 18 Crosstalk (control input to signal output) VC = 10 V (square wave), tr, tf = 20 ns, RL = 10 k 10 50 5 35 70 Turn-on and turn-off propagation delay VIN = VDD, tr, tf = 20 ns, CL = 50 pF, RL = 1 k 10 20 40 15 15 30 5 6 10 9 15 9.5 Maximum control input repetition rate CI See Figure 6 Vis = VDD, VSS = GND, RL = 1 k to GND, CL = 50 pF, VC = 10 V (square wave centered on 5 V), tr, tf = 20 ns, Vos = 1/2 Vos at 1 kHz V 0.1 0.1 1 1 10-5 Input capacitance 5 0.1 A mV ns MHz 7.5 pF switching characteristics SWITCH OUTPUT, Vos (V) SWITCH INPUT VDD (V) Vis (V) Iis (mA) -55C -40C 25C 85C 125C 5 0 0.64 0.61 0.51 0.42 0.36 5 5 -0.64 -0.61 -0.51 -0.42 -0.36 10 0 1.6 1.5 1.3 1.1 0.9 10 10 -1.6 -1.5 -1.3 -1.1 -0.9 15 0 4.2 4 3.4 2.8 2.4 15 15 -4.2 -4 -3.4 -2.8 -2.4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN MAX 0.4 4.6 0.5 9.5 1.5 13.5 5 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) 600 Supply Voltage (VDD - VSS) = 5 V 500 TA = 125C 400 300 +25C 200 -55C 100 0 -4 -3 -2 -1 0 1 2 3 4 r - Channel On-State Resistance - on r - Channel On-State Resistance - on TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) 300 Supply Voltage (VDD - VSS) = 10 V 250 TA = 125C 200 +25C 150 -55C 100 50 0 -10 -7.5 -5 -2.5 0 2.5 5 7.5 Vis - Input Signal Voltage - V Vis - Input Signal Voltage - V 92CS-27327RI 92CS-27326RI Figure 2 Figure 3 Supply Voltage (VDD - VSS) = 15 V 300 250 200 TA = 125C 150 +25C 100 -55C 50 0 -7.5 -5 -2.5 0 2.5 5 7.5 10 TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) r - Channel On-State Resistance - on r - Channel On-State Resistance - on TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) -10 TA = 125C 600 Supply Voltage (VDD - VSS) = 5 V 500 400 300 200 10 V -15 V 100 0 -10 -7.5 -5 -2.5 0 2.5 5 7.5 10 Vis - Input Signal Voltage - V Vis - Input Signal Voltage - V 92CS-27329RI 92CS-27330RI Figure 5 Figure 4 6 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS Iis Vis CD4066B 1 of 4 Switches ron = Vos |Vis - Vos| |Iis| 92CS-30966 Figure 6. Determination of ron as a Test Condition for Control-Input High-Voltage (VIHC) Specification Keithley 160 Digital Multimeter VDD TG On 10 k 1-k Range Y X-Y Plotter VSS H. P. Moseley 7030A X 92CS-22716 Figure 7. Channel On-State Resistance Measurement Circuit POWER DISSIPATION PER PACKAGE vs SWITCHING FREQUENCY TYPICAL ON CHARACTERISTICS FOR 1 OF 4 CHANNELS 3 VO - Output Voltage - V 2 1 0 VC = VDD -1 Vis CD4066B 1 of 4 Switches Vos RL VSS -2 -3 -3 VDD All unused terminals are connected to VSS -2 -1 0 1 2 3 PD - Power Dissipation Per Package - W 104 4 6 4 TA = 25C 2 103 Supply Voltage (VDD) = 15 V 6 4 2 10 V 102 5V 6 4 14 5 2 6 101 12 6 4 13 CD4066B 7 2 10 10 VDD 2 VI - Input Voltage - V 4 6 102 2 4 VSS 6 103 f - Switching Frequency - kHz 92CS-30919 Figure 9 Figure 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 92C-30920 7 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS Cios VDD = 5 V VC = -5 V CD4066B 1 of 4 Switches VC = VSS Vis = VDD Cis VSS = -5 V Cos Figure 10. Typical On Characteristics for One of Four Channels Vos I 92CS-30922 All unused terminals are connected to VSS. Figure 11. Off-Switch Input or Output Leakage VDD VC = VDD Vis CD4066B 1 of 4 Switches VSS 92CS-30921 Measured on Boonton capacitance bridge, model 75a (1 MHz); test-fixture capacitance nulled out. VDD CD4066B 1 of 4 Switches VSS +10 V Vos 50 pF VC tr = tf = 20 ns 200 k VDD VDD V Vis CD4066B os 1 of 4 Switches 10 k 1 k VSS tr = tf = 20 ns 92CS-30924 92CS-30923 All unused terminals are connected to VSS. All unused terminals are connected to VSS. Figure 12. Propagation Delay Time Signal Input (Vis) to Signal Output (Vos) 8 POST OFFICE BOX 655303 Figure 13. Crosstalk-Control Input to Signal Output * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS VDD VDD VC = VDD tr = tf = 20 ns CD4066B 1 of 4 Switches VDD VSS Vos 50 pF 1 k NOTES: A. All unused terminals are connected to VSS. B. Delay is measured at Vos level of +10% from ground (turn-on) or on-state output level (turn-off). 92CS-30925 Figure 14. Propagation Delay, tPLH, tPHL Control-Signal Output tr VC 10% tf 10 V 90% 50% 0V Repetition Rate tr = tf = 20 ns Vos V OS + V OS at 1 kHz 2 VDD = 10 V VC Vis = 10 V CD4066B 1 of 4 Switches V OS + 50 pF V OS at 1 kHz 2 1 k VSS All unused terminals are connected to VSS. 92CS-30925 Figure 15. Maximum Allowable Control-Input Repetition Rate POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS VDD Inputs VDD I VSS 92CS-27555 VSS Measure inputs sequentially to both VDD and VSS. Connect all unused inputs to either VDD or VSS. Measure control inputs only. Figure 16. Input Leakage-Current Test Circuit 10 10 Clock Reset 14 2 P E J1 7 9 12 J2 J3 J4 J5 Clock CD4018B 15 1 3 External Reset 13 14 P E J1 15 1/4 CD4066B 1 4 3 7 9 12 J2 J3 J4 J5 CD4018B Q1 Q2 1 Q1 Q2 5 2 5 2 4 13 1 3 7 2 2 1/3 CD4049B 5 6 4 8 9 8 6 5 2 1 1/3 CD4049B 5 CD4001B 3 12 6 4 9 CD4001B 10 10 11 4 3 10 9 6 12 5 12 13 6 5 Signal Outputs 11 11 13 Signal Inputs 11 12 Channel 1 Channel 2 4 Channel 3 CD4066B 5 9 11 10 3 4 4 Channel 4 1/4 CD4066B 3 8 9 10 k Maximum Allowable Signal Level LPF Channel 2 10 k CD4066B 11 Package Count 2 - CD4001B 1 - CD4049B 3 - CD4066B 2 - CD4018B Channel 1 1 3 8 LPF 10 k 1/6 CD4049B 2 1 2 12 LPF Channel 3 10 k VDD Clock 30% (VDD - VSS) VSS 10 LPF Channel 4 10 k Chan 1 Chan 2 Chan 3 Chan 4 92CM-30928 Figure 17. Four-Channel PAM Multiplex System Diagram 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS 5V 0 -5 V Analog Inputs (5 V) VDD = 5 V VDD = 5 V CD4066B 5V SWA 0 IN SWB CD4054B SWC SWD Digital Control Inputs VSS = 0 V VEE = -5 V Analog Outputs (5 V) VSS = -5 V 92CS-30927 Figure 18. Bidirectional Signal Transmission Via Digital Control Logic POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 APPLICATION INFORMATION In applications that employ separate power sources to drive VDD and the signal inputs, the VDD current capability should exceed VDD/RL (RL = effective external load of the four CD4066B bilateral switches). This provision avoids any permanent current flow or clamp action on the VDD supply when power is applied or removed from the CD4066B. In certain applications, the external load-resistor current can include both VDD and signal-line components. To avoid drawing VDD current when switch current flows into terminals 1, 4, 8, or 11, the voltage drop across the bidirectional switch must not exceed 0.8 V (calculated from ron values shown). No VDD current will flow through RL if the switch current flows into terminals 2, 3, 9, or 10. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 15-Oct-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty CD4066BE ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD4066BEE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD4066BF ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type 1 N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) CD4066BF3A ACTIVE CDIP J 14 TBD A42 CD4066BF3AS2283 OBSOLETE CDIP J 14 TBD Call TI Call TI CD4066BF3AS2534 OBSOLETE CDIP J 14 TBD Call TI Call TI CD4066BM ACTIVE SOIC D 14 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BM96 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BM96E4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BM96G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BME4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMT ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMTE4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMTG4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BNSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BNSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BNSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWE4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM JM38510/05852BCA ACTIVE CDIP J 14 50 1 (1) TBD The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. Addendum-Page 1 A42 N / A for Pkg Type PACKAGE OPTION ADDENDUM www.ti.com 15-Oct-2009 NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing CD4066BM96 SOIC SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) 9.0 2.1 8.0 16.0 Q1 D 14 2500 330.0 16.4 6.5 W Pin1 (mm) Quadrant CD4066BM96 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD4066BNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 CD4066BPWR TSSOP PW 14 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD4066BM96 SOIC D 14 2500 333.2 345.9 28.6 CD4066BM96 SOIC D 14 2500 346.0 346.0 33.0 CD4066BNSR SO NS 14 2000 346.0 346.0 33.0 CD4066BPWR TSSOP PW 14 2000 346.0 346.0 29.0 Pack Materials-Page 2 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated