LM98722CCMTX/NOPB - NATIONAL SEMICONDUCTOR

LM98722

LM98722 3 Channel, 16-Bit, 45 MSPS Analog Front End with LVDS/CMOS Output,

Integrated CCD/CIS Sensor Timing Generator and Spread Spectrum Clock

Generation

Literature Number: SNAS487

LM98722

September 24, 2009

3 Channel, 16-Bit, 45 MSPS Analog Front End with LVDS/

CMOS Output, Integrated CCD/CIS Sensor Timing

Generator and Spread Spectrum Clock Generation

General Description

The LM98722 is a fully integrated, high performance 16-Bit,

45 MSPS signal processing solution for digital color copiers,

scanners, and other image processing applications. High-

speed signal throughput is achieved with an innovative archi-

tecture utilizing Correlated Double Sampling (CDS), typically

employed with CCD arrays, or Sample and Hold (S/H) inputs

(for higher speed CCD or CMOS image sensors). The signal

paths utilize 8 bit Programmable Gain Amplifiers (PGA), a

+/-9-Bit offset correction DAC and independently controlled

Digital Black Level correction loops for each input. The PGA

and offset DAC are programmed independently allowing

unique values of gain and offset for each of the three analog

inputs. The signals are then routed to a 45MHz high perfor-

mance analog-to-digital converter (ADC). The fully differential

processing channel shows exceptional noise immunity, hav-

ing a very low noise floor of -74dB. The 16-bit ADC has

excellent dynamic performance making the LM98722 trans-

parent in the image reproduction chain.

A very flexible integrated Spread Spectrum Clock Generation

(SSCG) modulator is included to assist with EM compliance

and reduce system costs.

Applications

■Multi-Function Peripherals

■High-speed Currency/Check Scanners

■Flatbed or Handheld Color Scanners

■High-speed Document Scanners

Features

■LVDS/CMOS Outputs

■LVDS/CMOS/Crystal Clock Source with PLL Multiplication

■Integrated Flexible Spread Spectrum Clock Generation

■CDS or S/H Processing for CCD or CIS sensors

■Independent Gain/Offset Correction for Each Channel

■Automatic per-Channel Gain and Offset Calibration

■Programmable Input Clamp Voltage

■Flexible CCD/CIS Sensor Timing Generator

Key Specifications

■Maximum Input Level 1.2 or 2.4 Volt Modes

■(both with + or - polarity option)

■ADC Resolution 16-Bit

■ADC Sampling Rate 45 MSPS

■INL +18/-25 LSB (typ)

■Channel Sampling Rate 22.5/22.5/15 MSPS

■PGA Gain Steps 256 Steps

■PGA Gain Range 0.64 to 8.3x

■Analog DAC Resolution +/-9 Bits

■Analog DAC Range +/-307mV or +/-614mV

■Digital DAC Resolution +/-6 Bits

■Digital DAC Range -2048 LSB to + 2016 LSB

■SNR -74dB (@0dB PGA Gain)

■Power Dissipation 630mW (LVDS)

■Operating Temp 0 to 70°C

■Supply Voltage 3.3V Nominal (3.0V to 3.6V range)

System Block Diagram

30099570

LM98722 3 Channel, 16-Bit, 45 MSPS Analog Front End with LVDS/CMOS Output Integrated

Sensor Timing Generator and Spread Spectrum Clock Generation

LM98722 Overall Chip Block Diagram

30099501

FIGURE 1. Chip Block Diagram

www.national.com 2

LM98722

LM98722 Pin Out Diagram

30099502

FIGURE 2. LM98722 Pin Out Diagram

3 www.national.com

LM98722

Typical Application Diagram

30099573

FIGURE 3. Typical Application Diagram

www.national.com 4

LM98722

Pin Descriptions

Pin Name I/O Typ Res Description

1 PHIC2 O D PU Configurable high speed sensor timing output.

2 PHIC1 O D PD Configurable high speed sensor timing output.

3 SH1 O D PU Configurable low speed sensor timing output.

4 CE I D Chip Serial Interface Address Setting Input

CE Level Address

VD01

Float 10

DGND 00

5 CAL I D PD Initiate calibration sequence. Leave unconnected or tie to DGND if unused.

6 RESET I D PU Active-low master reset. NC when function not being used.

7 SH_R I D PD External request for an SH interval.

8 SDI I D PD Serial Interface Data Input.

9 SDO O D Serial Interface Data Output.

10 SCLK I D PD Serial Interface shift register clock.

11 SEN I D PU Active-low chip enable for the Serial Interface.

12 VA P Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.

13 AGND P Analog ground return.

14 VA P Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.

15 VREFB O A Bottom of ADC reference. Bypass with a 0.1μF capacitor to ground.

16 VREFT O A Top of ADC reference. Bypass with a 0.1μF capacitor to ground.

17 VA P Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.

18 AGND P Analog ground return.

19 VCLP IO A Input Clamp Voltage. Normally bypassed with a 0.1μF , and a 4.7μF capacitor to AGND.

An external reference voltage may be applied to this pin.

20 VA P Analog power supply. Bypass voltage source with 4.7μF and pin with 0.1μF to AGND.

21 IBIAS O A Bias setting pin. Connect a 9.0 kOhm 1% resistor to AGND.

22 AGND P Analog ground return.

23 OSRI A Analog input signal. Typically sensor Red output AC-coupled thru a capacitor.

24 AGND P Analog ground return.

25 OSGI A Analog input signal. Typically sensor Green output AC-coupled thru a capacitor.

26 AGND P Analog ground return.

27 OSBI A Analog input signal. Typically sensor Blue output AC-coupled thru a capacitor.

28 CPOFILT2 A Charge Pump Filter Capacitor. Bypass this supply pin with a 0.1μF capacitor to

CPOFILT1.

29 DGND P Digital ground return.

30 CPOFILT1 A Charge Pump Filter Capacitor. Bypass this supply pin with a 0.1μF capacitor to

CPOFILT2.

31 DVB O D Digital Core Voltage bypass. Not an input. Bypass with 0.1μF capacitor to DGND.

32 INCLK+ I D Clock Input. Non-Inverting input for LVDS clocks or CMOS clock input. CMOS clock is

selected when pin 29 is held at DGND, otherwise clock is configured for LVDS operation.

33 INCLK- I D Clock Input. Inverting input for LVDS clocks, connect to DGND for CMOS clock.

34 DOUT7/ O D Bit 7 of the digital video output bus in CMOS Mode, LVDS Frame Clock+ in LVDS Mode.

TXCLK+

35 DOUT6/ O D Bit 6 of the digital video output bus in CMOS Mode, LVDS Frame Clock- in LVDS Mode.

TXCLK-

36 DOUT5/ O D Bit 5 of the digital video output bus in CMOS Mode, LVDS Data Out2+ in LVDS Mode.

TXOUT2+

5 www.national.com

LM98722

Pin Name I/O Typ Res Description

37 DOUT4/ O D Bit 4 of the digital video output bus in CMOS Mode, LVDS Data Out2- in LVDS Mode.

TXOUT2-

38 DOUT3/ O D Bit 3 of the digital video output bus in CMOS Mode, LVDS Data Out1+ in LVDS Mode.

TXOUT1+

39 DOUT2/ O D Bit 2 of the digital video output bus in CMOS Mode, LVDS Data Out1- in LVDS Mode.

TXOUT1-

40 DOUT1/ O D Bit 1 of the digital video output bus in CMOS Mode, LVDS Data Out0+ in LVDS Mode.

TXOUT0+

41 DOUT0/ O D Bit 0 of the digital video output bus in CMOS Mode, LVDS Data Out0- in LVDS Mode.

TXOUT0-

42 DGND O D PD Configurable sensor control output.

43 VD P Power supply for the digital circuits. Bypass this supply pin with 0.1μF capacitor. A single

4.7μF capacitor should be used between the supply and the VD, VR and VC pins.

44 VC P Power supply for the sensor control outputs. Bypass this supply pin with 0.1μF capacitor.

45 CLKOUT/SH2 O D Output clock for registering output data when using CMOS outputs, or a configurable

low speed sensor timing output.

46 SH3 O D Configurable low speed sensor timing output.

47 RS O D Configurable high speed sensor timing output.

48 CP O D Configurable high speed sensor timing output.

49 PHIA1 O D Configurable high speed sensor timing output.

50 PHIA2 O D Configurable high speed sensor timing output.

51 DGND P Digital ground return.

52 VC P Power supply for the sensor control outputs.

Bypass this supply pin with 0.1μF capacitor.

53 PHIB1 O D Configurable high speed sensor timing output.

54 PHIB2 O D Configurable high speed sensor timing output.

55 SH4 O D Configurable low speed sensor timing output.

56 SH5 O D Configurable low speed sensor timing output.

(I=Input), (O=Output), (IO=Bi-directional), (P=Power), (D=Digital), (A=Analog), (PU=Pull Up with an internal resistor), (PD=Pull Down with an internal resistor.).

www.national.com 6

LM98722

Absolute Maximum Ratings (Note 1, Note

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Supply Voltage (VA,VR,VD,VC) 4.2V

Voltage on Any Input Pin

(Not to exceed 4.2V)

−0.3V to

(VA + 0.3V)

Voltage on Any Output Pin

(execpt DVB and not to exceed 4.2V)

−0.3V to

(VA + 0.3V)

DVB Output Pin Voltage 2.0V

Input Current at any pin other than

Supply Pins (Note 3)

±25 mA

Package Input Current (except Supply

Pins) (Note 3)

±50 mA

Maximum Junction Temperature (TA) 150°C

Thermal Resistance (θJA)<66°C/W

Package Dissipation at TA = 25°C

(Note 4)

>1.89W

ESD Rating (Note 5)

Human Body Model 2500V

Machine Model 250V

Storage Temperature −65°C to +150°C

Soldering process must comply with National

Semiconductor’s Reflow Temperature Profile

specifications. Refer to www.national.com/packaging.

(Note 6)

Operating Ratings (Note 1, Note 2)

Operating Temperature Range 0°C ≤ TA ≤ +70°C

All Supply Voltage +3.0V to +3.6V

Electrical Characteristics

The following specifications apply for VA = VD = VC = 3.3V, CL = 10pF, and fINCLK = 15MHz unless otherwise specified. Boldface

limits apply for TA = TMIN to TMAX; all other limits TA = 25°C.

Symbol Parameter Conditions Min

(Note 9)

Typ

(Note 8)

Max

(Note 9)Units

CMOS Digital Input DC Specifications (RESETb, SH_R, SCLK, SENb)

VIH Logical “1” Input Voltage 2.0 V

VIL Logical “0” Input Voltage 0.8 V

VIHYST Logic Input Hysteresis 0.6

IIH Logical “1” Input Current VIH = VD

RESET,SEN 100 nA

SH_R, SCLK, SDI, CAL 65 μA

CE 30 nA

IIL Logical “0” Input Current VIL = DGND

RESETSEN -65 μA

SH_R, SCLK, SDI, CAL -100 nA

CE -30 μA

CMOS Digital Output DC Specifications (SH1 to SH5, RS, CP, PHIA, PHIB, PHIC)

VOH Logical “1” Output Voltage IOUT = -0.5mA 3.0 V

VOL Logical “0” Output Voltage IOUT = 1.6mA 0.21 V

IOS Output Short Circuit Current VOUT = DGND 18 mA

VOUT= VD -25

IOZ CMOS Output TRI-STATE Current VOUT = DGND 20 nA

VOUT = VD -25

CMOS Digital Output DC Specifications (CMOS Data Outputs)

VOH Logical “1” Output Voltage IOUT = -0.5mA 2.3 V

VOL Logical “0” Output Voltage IOUT = 1.6mA 0.12 V

IOS Output Short Circuit Current VOUT = DGND 12 mA

VOUT= VD -14

IOZ CMOS Output TRI-STATE Current VOUT = DGND 20 nA

VOUT = VD -25

7 www.national.com

LM98722

Symbol Parameter Conditions Min

(Note 9)

Typ

(Note 8)

Max

(Note 9)Units

LVDS/CMOS Clock Receiver DC Specifications (INCLK+ and INCLK- Pins)

VIHL Differential LVDS Clock RL = 100Ω 200 mV

High Threshold Voltage VCM (LVDS Input Common Mode

Voltage)= 1.25V

VILL Differential LVDS Clock -200 mV

Low Threshold Voltage

VIHC CMOS Clock INCLK- = DGND 2.0 V

High Threshold Voltage

VILC CMOS Clock 0.8 V

Low Threshold Voltage

IIHL CMOS Clock 230 260 μA

Input High Current

IILC CMOS Clock -135 -120 μA

Input Low Current

LVDS Output DC Specifications

VOD Differential Output Voltage RL = 100Ω 280 390 490 mV

VOS LVDS Output Offset Voltage 1.08 1.20 1.33 V

IOS Output Short Circuit Current VOUT = 0V, RL = 100Ω 8.5 mA

Power Supply Specifications

IA VA Analog Supply Current LVDS Output Data Format 139 162 mA

LVDS Output Data Format

(Powerdown)

3.1 4.5 mA

CMOS Output Data Format

(40 MHz)

137 161 mA

ID VD Digital Output Driver Supply

Current

LVDS Output Data Format 50 65 mA

LVDS Output Data Format

(Powerdown)

5.5 8 mA

CMOS Output Data Format

(ATE Loading of CMOS Outputs

> 50 pF) (40 MHz)

48 62 mA

IC VC CCD Timing Generator Output

Driver Supply Current

Typical sensor outputs: 1 4 mA

SH1-SH5, PHIA, PHIB, PHIC,

RS, CP

(ATE Loading of CMOS

Outputs > 50pF)

PWR Average Power Dissipation LVDS Output Data Format 630 736 mW

LVDS Output Data Format

(Powerdown)

28 32 mW

CMOS Output Data Format

(ATE Loading of CMOS Outputs

> 50pF) (40 MHz)

600 740 mW

Input Sampling Circuit Specifications

VIN Input Voltage Level CDS Gain=1x, PGA Gain=1x 2.3 Vp-p

CDS Gain=2x, PGA Gain= 1x 1.22

www.national.com 8

LM98722

Symbol Parameter Conditions Min

(Note 9)

Typ

(Note 8)

Max

(Note 9)Units

IIN_SH Sample and Hold Mode Source Followers Off 19 25 μA

Input Leakage Current CDS Gain = 1x (-103) (-95)

OSX = VA (OSX = AGND)

Source Followers Off 33 50 μA

CDS Gain = 2x (-152) (-141)

OSX = VA (OSX = AGND)

Source Followers On 20 250 nA

CDS Gain = 2x (-250) (-50)

OSX = VA (OSX = AGND)

CSH Sample/Hold Mode CDS Gain = 1x 2.5 pF

Equivalent Input Capacitance

CDS Gain = 2x 4 pF

IIN_CDS CDS Mode Source Followers Off 10 250 nA

Input Leakage Current OSX = VA (OSX = AGND) (-250) (-50)

RCLPIN CLPIN Switch Resistance 16 55 Ω

(OSX to VCLP Node)

VCLP Reference Circuit Specifications

VVCLP

VCLP Voltage 000 VCLP Voltage Setting = 000 0.85VA V

VCLP Voltage 001 VCLP Voltage Setting = 001 0.9VA V

VCLP Voltage 010 VCLP Voltage Setting = 010 0.95VA V

VCLP Voltage 011 VCLP Voltage Setting = 011 0.6VA V

VCLP Voltage 100 VCLP Voltage Setting = 100 0.55VA V

VCLP Voltage 101 VCLP Voltage Setting = 101 0.4VA V

VCLP Voltage 110 VCLP Voltage Setting = 110 0.35VA V

VCLP Voltage 111 VCLP Voltage Setting = 111 0.15VA V

ISC VCLP DAC Short Circuit Output

Current

0001 xxxxb VCLP Config.

30 mA

Black Level Offset DAC Specifications

Resolution 10 Bits

Monotonicity Guaranteed by characterization

Offset Adjustment Range CDS Gain = 1x

mVReferred to AFE Input Minimum DAC Code = 0x000 -614

Maximum DAC Code = 0x3FF 614

CDS Gain = 2x

mV Minimum DAC Code = 0x000 -307

Maximum DAC Code = 0x3FF 307

Offset Adjustment Range Minimum DAC Code = 0x000 -17500 -16130 LSB

Referred to AFE Output Maximum DAC Code = 0x3FF +16130 +17500

DAC LSB Step Size CDS Gain = 1x 1.2 mV

Referred to AFE Output (32) (LSB)

DNL Differential Non-Linearity -0.85 +0.74/

-0.37

+2.4 LSB

INL Integral Non-Linearity -2.5 +0.72/

-0.56

+2.5 LSB

PGA Specifications

Gain Resolution 8 Bits

Monotonicity Guaranteed by characterization

Maximum Gain CDS Gain = 1x 7.7 8.3 8.8 V/V

CDS Gain = 1x 17.7 18.4 18.9 dB

9 www.national.com

LM98722

Symbol Parameter Conditions Min

(Note 9)

Typ

(Note 8)

Max

(Note 9)Units

Minimum Gain CDS Gain = 1x 0.58 0.64 0.70 V/V

CDS Gain = 1x -4.7 -4.2 -3.5 dB

PGA Function Gain (V/V) = (180/(277-PGA Code))

Gain (dB) = 20LOG10(180/(277-PGA Code))

Channel Matching Minimum PGA Gain 3 %

Maximum PGA Gain 12.7

ADC Specifications

VREFT Top of Reference 2.07 V

VREFB Bottom of Reference 0.89 V

VREFT -

VREFB

Differential Reference Voltage 1.06 1.18 1.30 V

Overrange Output Code 65535

Underrange Output Code 0

Digital Offset “DAC” Specifications

Resolution 7 Bits

Digital Offset DAC LSB Step Size Referred to AFE Output 32 LSB

Offset Adjustment Range Min DAC Code =7b0000000 -2048

LSBReferred to AFE Output Mid DAC Code =7b1000000 0

Max DAC Code = 7b1111111 +2016

Full Channel Performance Specifications

DNL Differential Non-Linearity (Note 10) -0.999 +0.8/-0.7 2.5 LSB

INL Integral Non-Linearity (Note 10) -75 +18/-25 75 LSB

SNR Total Output Noise

Minimum PGA Gain

(Note 10)

-76 dB

10 26 LSB RMS

Maximum PGA Gain

(Note 10)

-56 dB

96 LSB RMS

Channel to Channel Crosstalk Mode 3 26 LSB

Mode 2 17

www.national.com 10

LM98722

AC Timing Specifications

The following specifications apply for VA = VD = VC = 3.3V, CL = 10pF, and fINCLK = 15MHz unless otherwise specified. Boldface

limits apply for TA = TMIN to TMAX; all other limits TA = 25°C.

Symbol Parameter Conditions

Min

(Note

Typ

(Note 8)

Max

(Note 9)Units

Input Clock Timing Specifications

fINCLK Input Clock Frequency

INCLK = PIXCLK 0.66

15 (Mode 3)

MHz(Pixel Rate Clock) 1 22.5 (Mode 2)

1 22.5 (Mode 1)

INCLK = ADCCLK

45 (Mode 3)

MHz(ADC Rate Clock) 45 (Mode 2)

22.5 (Mode 1)

Tdc Input Clock Duty Cycle 40/60 50/50 60/40 %

Full Channel Latency Specifications

tLAT3

3 Channel Mode Pipeline Delay PIXPHASE0 24

TADC

PIXPHASE1 23 1/2

PIXPHASE2 23

PIXPHASE3 22 1/2

tLAT2

2 Channel Mode Pipeline Delay PIXPHASE0 21

TADC

PIXPHASE1 20 1/2

PIXPHASE2 20

PIXPHASE3 19 1/2

tLAT1

1 Channel Mode Pipeline Delay PIXPHASE0 19

TADC

PIXPHASE1 18 1/2

PIXPHASE2 18

PIXPHASE3 17 1/2

SH_R Timing Specifications

tSHR_S SH_R Setup Time 2 ns

tSHR_H SH_R Hold Time 2 ns

LVDS Output Timing Specifications

TXpp0 TXCLK to Pulse Position 0 LVDS Output -0.46 0 0.46 ns

TXpp1 TXCLK to Pulse Position 1 Specifications not 2.71 3.17 3.63 ns

TXpp2 TXCLK to Pulse Position 2 tested in production. 5.89 6.35 6.81 ns

TXpp3 TXCLK to Pulse Position 3 Min/Max guaranteed 9.06 9.52 9.98 ns

TXpp4 TXCLK to Pulse Position 4 by design, 12.24 12.70 13.16 ns

TXpp5 TXCLK to Pulse Position 5 characterization and statistical 15.41 15.87 16.33 ns

TXpp6 TXCLK to Pulse Position 6 analysis. 18.59 19.05 19.51 ns

CMOS Output Timing Specifications

tCRDO

CLKOUT Rising Edge to CMOS

Output Data Transition

fINCLK = 40MHz

2 6 9 ns

INCLK = ADCCLK

(ADC Rate Clock)

Serial Interface Timing Specifications

11 www.national.com

LM98722

Symbol Parameter Conditions

Min

(Note

Typ

(Note 8)

Max

(Note 9)Units

fSCLK Input Clock Frequency

fSCLK <= fINCLK

15/22.5/22.5 MHz

INCLK = PIXCLK

(Pixel Rate Clock)

Mode 3/2/1

fSCLK <= fINCLK

45/45/22.5 MHz

INCLK = ADCCLK

(ADC Rate Clock)

Mode 3/2/1

SCLK Duty Cycle 50/50 ns

tIH Input Hold Time 1.5 ns

tIS Input Setup Time 2.5 ns

tSENSC SCLK Start Time After SEN Low 1.5 ns

tSCSEN

SEN High after last SCLK Rising

Edge 2.5 ns

tSENW SEN Pulse Width

INCLK present 6

TINCLK

INCLK stopped

(Note 11, Note 12)

50 ns

tOD Output Delay Time 11 14 ns

tHZ Data Output to High Z 0.5 TSCLK

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions. Operation of the device beyond the Operating Ratings is not recommended.

Note 2: All voltages are measured with respect to AGND = DGND = 0V, unless otherwise specified.

Note 3: When the input voltage (VIN) at any pin exceeds the power supplies (VIN < GND or VIN > VA or VD), the current at that pin should be limited to 25 mA.

The 50 mA maximum package input current rating limits the number of pins that can simultaneously safely exceed the power supplies with an input current of 25

mA to two.

Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA and the ambient temperature, TA. The maximum

allowable power dissipation at any temperature is PD = (TJMAX – TA)/θJA. The values for maximum power dissipation listed above will be reached only when the

device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed).

Such conditions should always be avoided.

Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through 0Ω.

Note 6: Reflow temperature profiles are different for lead-free and non-lead-free packages.

Note 7: The analog inputs are protected as shown below. Input voltage magnitudes beyond the supply rails will not damage the device, provided the current is

limited per note 3. However, input errors will be generated If the input goes above VA and below AGND.

30099571

Note 8: Typical figures are at TA = 25°C, and represent most likely parametric norms at the time of product characterization. The typical specifications are not

guaranteed.

Note 9: Test limis are guaranteed to National's AOQL (Average Outgoing Quality Level).

Note 10: This parameter guaranteed by design and characterization.

Note 11: If the input INCLK is divided down to a lower internal clock rate via the PLL, the parameter tSENW will be increased by the same factor.

Note 12: When the Spread Spectrum Clock Generation feature is enabled, tSENW should be increased by 1.

www.national.com 12

LM98722

Physical Dimensions inches (millimeters) unless otherwise noted

56-Lead TSSOP

NS Package Number MTD56

13 www.national.com

LM98722

Notes

LM98722 3 Channel, 16-Bit, 45 MSPS Analog Front End with LVDS/CMOS Output Integrated

Sensor Timing Generator and Spread Spectrum Clock Generation

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench

Audio www.national.com/audio App Notes www.national.com/appnotes

Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns

Data Converters www.national.com/adc Samples www.national.com/samples

Interface www.national.com/interface Eval Boards www.national.com/evalboards

LVDS www.national.com/lvds Packaging www.national.com/packaging

Power Management www.national.com/power Green Compliance www.national.com/quality/green

Switching Regulators www.national.com/switchers Distributors www.national.com/contacts

LDOs www.national.com/ldo Quality and Reliability www.national.com/quality

LED Lighting www.national.com/led Feedback/Support www.national.com/feedback

Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy

PowerWise® Solutions www.national.com/powerwise Solutions www.national.com/solutions

Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero

Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic

Wireless (PLL/VCO) www.national.com/wireless PowerWise® Design

University

www.national.com/training

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email: support@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265