+3 V/+5 V/5 V, CMOS, 8-Channel Analog Multiplexer ADG658-EP Enhanced Product FEATURES FUNCTIONAL BLOCK DIAGRAM 2 V to 6 V dual supply 2 V to 12 V single supply <0.1 nA leakage currents (typical) 45 typical on resistance over full signal range Rail-to-rail switching operation Single, 8 to 1 multiplexer 16-lead TSSOP package 0.01 A typical supply current TTL/CMOS compatible inputs ADG658-EP S1 D S8 ENHANCED PRODUCT FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range: -55C to +125C Controlled manufacturing baseline One assembly/test site One fabrication site Enhanced product change notification Qualification data available on request APPLICATIONS Automatic test equipment Data acquisition systems Battery-powered systems Communication systems Audio and video signal routing Relay replacement Sample-and-hold systems Industrial control systems A0 A1 A2 EN SWITCHES SHOWN FOR A LOGIC 1 INPUT. 15981-001 1 OF 8 DECODER Figure 1. GENERAL DESCRIPTION The ADG658-EP is a low voltage, CMOS analog multiplexer comprised of eight single channels. The ADG658-EP switches one of eight inputs (S1 to S8) to a common output, D, as determined by the 3-bit binary address lines A0, A1, and A2. An EN input enables or disables the device. When disabled, all channels are switched off. The ADG658-EP is designed on an enhanced process that provides lower power dissipation yet gives high switching speeds. It can operate equally well as either a multiplexer or a demultiplexer, and has an input range that extends to the supplies. All channels exhibit break-before-make switching action, preventing momentary shorting when switching channels. All digital inputs have +0.8 V to +2.4 V logic thresholds, ensuring TTL/CMOS logic compatibility when using single +5 V or dual 5 V supplies. The ADG658-EP is available in a 16-lead TSSOP package. Additional application and technical information can be found in the ADG658 data sheet. PRODUCT HIGHLIGHTS 1. 2. 3. 4. Rev. 0 Single-supply and dual-supply operation. The ADG658-EP offers high performance and is fully specified and guaranteed with 5 V, +5 V, and +3 V supply rails. Military temperature range -55C to +125C. Low supply current, typically 0.01 A. 16-lead TSSOP package. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2017 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADG658-EP Enhanced Product TABLE OF CONTENTS Features .............................................................................................. 1 5 V Single Supply ...........................................................................3 Enhanced Product Features ............................................................ 1 2.7 V to 3.6 V Single Supply .........................................................5 Applications ....................................................................................... 1 Absolute Maximum Ratings ............................................................6 Functional Block Diagram .............................................................. 1 ESD Caution...................................................................................6 General Description ......................................................................... 1 Pin Configurations and Function Descriptions ............................7 Product Highlights ........................................................................... 1 Typical Performance Characteristics ..............................................8 Revision History ............................................................................... 2 Outline Dimensions ....................................................................... 10 Specifications..................................................................................... 3 Ordering Guide .......................................................................... 10 Dual Supply ................................................................................... 3 REVISION HISTORY 8/2017--Revision 0: Initial Version Rev. 0 | Page 2 of 10 Enhanced Product ADG658-EP SPECIFICATIONS DUAL SUPPLY VDD = 5 V 10%, VSS = -5 V 10%, GND = 0 V, unless otherwise noted. Table 1. Parameter ANALOG SWITCH Analog Signal Range On Resistance, RON On Resistance Match Between Channels, RON On Resistance Flatness, RFLAT(ON) +25C -55C to +125C VSS to VDD 45 75 1.3 3 10 16 100 3.5 18 Unit Test Conditions/Comments V typ max typ max typ max VDD = +4.5 V, VSS = -4.5 V Source voltage (VS) = 4.5 V, source current (IS) = 1 mA VS = 3.5 V, IS = 1 mA VDD = +5 V, VSS = -5 V VS = 3 V, IS = 1 mA VDD = +5.5 V, VSS = -5.5 V LEAKAGE CURRENTS Source Off Leakage, IS (OFF) 0.005 nA typ Drain voltage (VD) = 4.5 V, VS = 4.5 V 5 Drain Off Leakage, ID (OFF) 0.2 0.005 nA max nA typ VD = 4.5 V, VS = 4.5 V 0.2 0.005 0.2 5 5 nA max nA typ nA max 2.4 0.8 V min V max A typ A max pF typ Input voltage (VIN) = VINL or VINH 1 ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ pC max dB typ % typ MHz typ pF typ pF typ pF typ Load resistance (RL) = 300 , load capacitance (CL) = 35 pF VS = 3 V RL = 300 , CL = 35 pF VS = 3 V RL = 300 , CL = 35 pF VS = 3 V RL = 300 , CL = 35 pF Source 1 voltage (VS1) = 3 V, source 2 voltage (VS2) = 3 V VS = 0 V, RS = 0 CL = 1 nF RL = 50 , CL = 5 pF, f = 1 MHz RL = 600 , 2 V p-p, f = 20 Hz to 20 kHz RL = 50 , CL = 5 pF Channel On Leakage ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS1 Transition Time, tTRANSITION EN On Time, tON (EN) EN Off Time, tOFF (EN) Break-Before-Make Time Delay, tBBM 0.005 2 80 115 80 115 30 45 50 165 165 55 10 Charge Injection Off Isolation Total Harmonic Distortion Plus Noise, THD + N -3 dB Bandwidth Source Capacitance, CS (OFF) Drain Capacitance, CD (OFF) CD, CS (ON) POWER REQUIREMENTS Positive Power Supply Current, IDD 2 4 -90 0.025 210 4 23 28 0.01 1 Negative Power Supply Current, ISS 0.01 1 1 A typ A max A typ A max Guaranteed by design; not subject to production test. Rev. 0 | Page 3 of 10 VD = VS = 4.5 V f = 1 MHz f = 1 MHz f = 1 MHz VDD = +5.5 V, VSS = -5.5 V Digital inputs = 0 V or 5.5 V Digital inputs = 0 V or 5.5 V ADG658-EP Enhanced Product 5 V SINGLE SUPPLY VDD = 5 V 10%, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 2. Parameter ANALOG SWITCH Analog Signal Range On Resistance, RON On Resistance Match Between Channels, RON On Resistance Flatness, RFLAT(ON) LEAKAGE CURRENTS Source Off Leakage, IS (OFF) Drain Off Leakage, ID (OFF) Channel On Leakage ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 1 Transition Time, tTRANSITION EN On Time, tON (EN) EN Off Time, tOFF (EN) Break-Before-Make Time Delay, tBBM +25C 85 150 4.5 8 13 0.005 0.2 0.005 0.2 0.005 0.2 -55C to +125C Unit Test Conditions/Comments 0 to VDD V typ max typ max typ VDD = 4.5 V, VSS = 0 V VS = 0 V to 4.5 V, IS = 1 mA 200 10 16 5 2.4 0.8 V min V max A typ A max pF typ VIN = VINL or VINH 1 ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ pC max dB typ MHz typ pF typ pF typ pF typ RL = 300 , CL = 35 pF VS = 3 V RL = 300 , CL = 35 pF VS = 3 V RL = 300 , CL = 35 pF VS = 3 V RL = 300 , CL = 35 pF VS1 = VS2 = 3 V VS = 2.5 V, RS = 0 , CL = 1 nF 5 5 2 300 280 70 10 Charge Injection Off Isolation -3 dB Bandwidth Source Capacitance, CS (OFF) Drain Capacitance, CD (OFF) CD, CS (ON) POWER REQUIREMENTS Positive Power Supply Current, IDD 0.5 1 -90 180 5 29 30 0.01 A typ A max 1 1 VDD = 5 V, VSS = 0 V, VS = 1.5 V to 4 V, IS = 1 mA VDD = 5.5 V VS = 1 V/4.5 V, VD = 4.5 V/1 V nA typ nA max nA typ nA max nA typ nA max 0.005 120 200 120 190 35 50 100 VS = 3.5 V, IS = 1 mA Guaranteed by design; not subject to production test. Rev. 0 | Page 4 of 10 VS = 1 V/4.5 V, VD = 4.5 V/1 V VS = VD = 1 V or 4.5 V RL = 50 , CL = 5 pF, f = 1 MHz RL = 50 , CL = 5 pF f = 1 MHz f = 1 MHz f = 1 MHz VDD = 5.5 V Digital inputs = 0 V or 5.5 V Enhanced Product ADG658-EP 2.7 V TO 3.6 V SINGLE SUPPLY VDD = 2.7 to 3.6 V, VSS = 0 V, GND = 0 V, unless otherwise noted. Table 3. Parameter ANALOG SWITCH Analog Signal Range On Resistance, RON On Resistance Match Between Channels, RON LEAKAGE CURRENTS Source Off Leakage, IS (OFF) Drain Off Leakage, ID (OFF) Channel On Leakage ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current IINL or IINH Digital Input Capacitance, CIN DYNAMIC CHARACTERISTICS 1 Transition Time, tTRANSITION EN On Time, tON (EN) EN Off Time, tOFF (EN) Break-Before-Make Time Delay, tBBM +25C 185 300 2 4.5 0.005 0.2 0.005 0.2 0.005 0.2 -55C to +125C Unit Test Conditions/Comments 0 to VDD V typ max typ max VDD = 2.7 V, VSS = 0 V VS = 0 V to 2.7 V, IS = 0.1 mA 400 7 5 2.0 0.5 V min V max A typ A max pF typ VIN = VINL or VINH 1 ns typ ns max ns typ ns max ns typ ns max ns typ ns min pC typ pC max dB typ MHz typ pF typ pF typ pF typ RL = 300 , CL = 35 pF VS = 1.5 V RL = 300 , CL = 35 pF VS = 1.5 V RL = 300 , CL = 35 pF VS = 1.5 V RL = 300 , CL = 35 pF VS1 = VS2 = 1.5 V VS = 1.5 V, RS = 0 , CL = 1 nF 5 5 2 490 490 110 10 Charge Injection Off Isolation -3 dB Bandwidth Source Capacitance, CS (OFF) Drain Capacitance, CD (OFF) CD, CS (ON) POWER REQUIREMENTS Positive Power Supply Current, IDD 1 2 -90 160 5 29 30 0.01 1 1 VDD = 3.3 V VS = 1 V/3 V, VD = 3 V/1 V nA typ nA max nA typ nA max nA typ nA max 0.005 200 370 230 370 50 80 200 VS = 1.5 V, IS = 0.1 mA Guaranteed by design; not subject to production test. Rev. 0 | Page 5 of 10 A typ A max VS = 1 V/3 V, VD = 3 V/1 V VS = VD = 1 V or 3 V RL = 50 , CL = 5 pF, f = 1 MHz RL = 50 , CL = 5 pF f = 1 MHz f = 1 MHz f = 1 MHz VDD = 3.6 V Digital inputs = 0 V or 3.6 V ADG658-EP Enhanced Product ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 4. Parameter VDD to VSS VDD to GND VSS to GND Analog Inputs 1 Digital Inputs1 Rating 13 V -0.3 V to +13 V +0.3 V to -6.5 V VSS - 0.3 V to VDD + 0.3 V GND - 0.3 V to VDD + 0.3 V or 10 mA, whichever occurs first 40 mA Peak Current, Sx or D (Pulsed at 1 ms, 10% duty cycle max) Continuous Current, Sx or D Operating Temperature Range Storage Temperature Range Junction Temperature JA Thermal Impedance 16-Lead TSSOP Lead Temperature, Soldering Vapor Phase (60 sec) Infrared (15 sec) ESD (Human Body Model) 1 Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION 20 mA -55C to +125C -65C to +150C 150C 150.4C/W 215C 220C 4.0 kV Overvoltages at AX, EN, Sx, or D are clamped by internal diodes. Current must be limited to the maximum ratings. Table 5. Truth Table A2 A1 A0 X 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 1 1 1 1 EN 1 0 0 0 0 0 0 0 0 Switch Condition None 1 2 3 4 5 6 7 8 X means don't care Rev. 0 | Page 6 of 10 Enhanced Product ADG658-EP S5 1 16 VDD S7 2 15 S3 D 3 14 S2 S8 4 ADG658-EP 13 S1 S6 5 TOP VIEW (Not to Scale) 12 S4 EN 6 11 A0 VSS 7 10 A1 GND 8 9 A2 15981-002 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 2. 16-Lead TSSOP Pin Configuration Table 6. 16-Lead TSSOP Pin Function Descriptions Pin No. 1, 2, 4, 5, 12, 13, 14, 15 3 6 Mnemonic S1 to S8 Description Source Terminals. Can be an input or output. D EN 7 8 9, 10, 11 16 VSS GND A0 to A2 VDD Drain Terminal. Can be an input or output. Active Low Digital Input. When high, device is disabled and all switches are off. When low, Ax logic inputs determine on switch. Most Negative Power Supply Potential. Ground (0 V) Reference. Logic Control Inputs. Most Positive Power Supply Potential. Rev. 0 | Page 7 of 10 ADG658-EP Enhanced Product TYPICAL PERFORMANCE CHARACTERISTICS 100 1.5 90 1.0 IS (OFF) 70 60 +125C +85C 50 40 +25C -40C 30 -55C 20 -3 -2 -1 0 1 2 3 4 5 VD, VS (V) 15981-003 -4 0 -0.5 ID (OFF) -1.0 ID (ON), IS (ON) -1.5 VDD = +5V -2.0 VSS = -5V VD = 4V VS = 4V -2.5 0 20 10 0 -5 0.5 40 60 80 Figure 3. On Resistance vs. VD (VS) for Different Temperatures (Dual Supply) 1.5 120 1.0 VDD = +5V VSS = 0V VD = 4V VS = 1V LEAKAGE CURRENT (nA) +85C 60 -40C -55C 40 20 0 -0.5 ID (OFF) -1.0 ID (ON), IS (ON) -1.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VD, VS (V) 15981-004 -2.0 0 Figure 4. On Resistance vs. VD (VS) for Different Temperatures (Single Supply) 300 250 +125C ON RESISTANCE () IS (OFF) 0.5 +85C 200 +25C -40C 150 -55C 100 0 0 0.5 1.0 1.5 VD, VS (V) 2.0 2.5 3.0 15981-005 50 Figure 5. On Resistance vs. VD (VS) for Different Temperatures (Single Supply) Rev. 0 | Page 8 of 10 -2.5 0 20 40 60 80 100 120 TEMPERATURE (C) Figure 7. Leakage Current vs. Temperature (Single Supply) 15981-007 ON RESISTANCE () +125C 100 +25C 120 Figure 6. Leakage Current vs. Temperature (Dual Supply) 140 80 100 TEMPERATURE (C) 15981-006 LEAKAGE CURRENT (nA) ON RESISTANCE () 80 Enhanced Product ADG658-EP 140 350 VDD = +5V VSS = -5V VSS = 0V 120 300 100 250 VDD = 3V TIME (ns) 60 40 200 VDD = 5V 150 tON VDD = 3V 100 tOFF 50 VDD = 5V tOFF 0 -55 -35 -15 5 25 45 65 85 105 TEMPERATURE (C) 125 0 -55 -35 -15 5 25 45 65 85 105 TEMPERATURE (C) Figure 9. tON/tOFF Time vs. Temperature (Single Supply) Figure 8. tON/tOFF Time vs. Temperature (Dual Supply) Rev. 0 | Page 9 of 10 125 15981-009 20 15981-008 TIME (ns) tON 80 ADG658-EP Enhanced Product OUTLINE DIMENSIONS 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.20 0.09 0.30 0.19 0.65 BSC COPLANARITY 0.10 SEATING PLANE 8 0 0.75 0.60 0.45 COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 10. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADG658TRUZ-EP ADG658TRUZ-EP-RL7 1 Temperature Range -55C to +125C -55C to +125C Package Description 16-Lead Thin Shrink Small Outline Package [TSSOP] 16-Lead Thin Shrink Small Outline Package [TSSOP] Z = RoHS Compliant Part. (c)2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D15981-0-8/17(0) Rev. 0 | Page 10 of 10 Package Option RU-16 RU-16