19-3175; Rev 1; 7/04 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers The MAX5069 is a high-frequency, current-mode, pulse-width modulation (PWM) controller (with dual MOSFET drivers) that integrates all the building blocks necessary for implementing AC-DC or DC-DC fixed-frequency power supplies. Isolated or nonisolated pushpull and half/full-bridge power supplies are easily constructed using either primary- or secondary-side regulation. Current-mode control with leading-edge blanking simplifies control-loop design and a programmable internal slope-compensation circuit stabilizes the current loop when operating at duty cycles above 50%. An input undervoltage lockout (UVLO) programs the input-supply startup voltage and ensures proper operation during brownout conditions. A single external resistor programs the oscillator frequency from 50kHz to 2.5MHz. The MAX5069A/D provide a SYNC input for synchronization to an external clock. The maximum FET-driver duty cycle for the MAX5069 is 50%. Programmable dead time allows additional flexibility in optimizing magnetic design and overcoming parasitic effects. Programmable hiccup current limit provides additional protection under severe faults. The MAX5069 is specified over the -40C to +125C automotive temperature range and is available in a 16-pin thermally enhanced TSSOP-EP package. Refer to the MAX5068 data sheet for single FET-driver applications. Warning: The MAX5069 is designed to work with high voltages. Exercise caution. Features Current-Mode Control with 47A (typ) Startup Current Oscillator Frequency Programmable to 2.5MHz Resistor-Programmable 4.5% Accurate Switching Frequency Dual Gate-Drive Output for Half/Full-Bridge or Push-Pull Applications Rectified 85VAC to 265VAC, or 36VDC to 72VDC Input (MAX5069A/B) Input Directly Driven from 10.8V to 24V (MAX5069C/D) Programmable Dead Time and Slope Compensation Programmable Startup Voltage (UVLO) Programmable UVLO Hysteresis (MAX5069B/C) Frequency Synchronization Input (MAX5069A/D) -40C to +125C Automotive Temperature Range 16-Pin Thermally Enhanced TSSOP-EP Package Ordering Information TEMP RANGE PIN-PACKAGE MAX5069AAUE PART -40C to +125C 16 TSSOP-EP* MAX5069BAUE -40C to +125C 16 TSSOP-EP* MAX5069CAUE -40C to +125C 16 TSSOP-EP* MAX5069DAUE -40C to +125C 16 TSSOP-EP* *EP = Exposed pad. Applications Universal-Input AC Power Supplies Pin Configuration Isolated Telecom Power Supplies Networking System Power Supplies TOP VIEW Server Power Supplies Industrial Power Conversion RT 1 16 REG5 SYNC(HYST*) 2 15 IN SCOMP 3 DT 4 14 VCC MAX5069 13 NDRVA 12 NDRVB UVLO/EN 5 FB 6 11 PGND COMP 7 10 AGND FLTINT 8 9 CS TSSOP-EP *MAX5069B/C. Selector Guide appears at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX5069 General Description MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers ABSOLUTE MAXIMUM RATINGS IN to PGND ............................................................-0.3V to +30V IN to AGND.............................................................-0.3V to +30V VCC to PGND..........................................................-0.3V to +13V VCC to AGND..........................................................-0.3V to +13V FB, COMP, CS, HYST, SYNC, REG5 to AGND ........-0.3V to +6V UVLO/EN, RT, DT, SCOMP, FLTINT to AGND .........-0.3V to +6V NDRVA, NDRVB to PGND ..........................-0.3V to (VCC + 0.3V) AGND to PGND .....................................................-0.3V to +0.3V Continuous Power Dissipation (TA = +70C) 16-Pin TSSOP-EP (derate 21.3mW/C above +70C) ...1702mW Operating Temperature Range..........................-40C to +125C Maximum Junction Temperature .....................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VIN = +12V for the MAX5069C/D, VIN = +23.6V for the MAX5069A/B at startup, then reduces to +12V, CIN = CREG5 = 0.1F, CVCC = 1F, RRT = 100k, NDRV_ = floating, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS UNDERVOLTAGE LOCKOUT/STARTUP Bootstrap UVLO Wake-Up Level VSUVR VIN rising, MAX5069A/B 19.68 21.6 23.60 V Bootstrap UVLO Shutdown Level VSUVF VIN falling, MAX5069A/B 9.05 9.74 10.43 V UVLO/EN Wake-Up Threshold VULR2 UVLO/EN rising 1.205 1.230 1.255 V UVLO/EN Shutdown Threshold VULF2 UVLO/EN falling HYST FET On-Resistance RDS(ON)_H 1.18 V MAX5069B/C only, sinking 50mA, VUVLO/EN = 0V 10 nA HYST FET Leakage Current ILEAK_H VUVLO/EN = 2V, VHYST = 5V 3 IN Supply Current In Undervoltage Lockout ISTART VIN = +19V, VUVLO/EN < VULF2 47 IN Range VIN 10.8 90 A 24.0 V 10.5 V INTERNAL SUPPLIES (VCC and REG5) VCC Regulator Set Point VCCSP VIN = +10.8V to +24V, VCC sourcing 1A to 25mA 7.0 REG5 Output Voltage VREG5 IREG5 = 0 to 1mA 4.85 REG5 Short-Circuit Current Limit IREG5_SC IN Supply Current After Startup IIN Shutdown Supply Current 5.00 5.15 18 VIN = +24V fSW = 1.25MHz 7 fSW = 100kHz 3 IVIN_SD V mA mA 90 A GATE DRIVER (NDRVA, NDRVB) Driver Output Impedance Driver Peak Output Current NDRVA/NDRVB sinking 100mA 2 4 ZOUT(HIGH) NDRVA/NDRVB sourcing 25mA ZOUT(LOW) 3 6 INDRV Sinking 1000 Sourcing 650 mA PWM COMPARATOR Comparator Offset Voltage VOS_PWM VCOMP > VCS Comparator Propagation Delay tPD_PWM VCS = 0.1V 1.30 1.60 40 2.00 ns V Minimum On-Time tON(MIN) Includes tCS_BLANK 110 ns CURRENT-LIMIT COMPARATOR Current-Limit Trip Threshold 2 VCS 298 314 _______________________________________________________________________________________ 330 mV High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers (VIN = +12V for the MAX5069C/D, VIN = +23.6V for the MAX5069A/B at startup, then reduces to +12V, CIN = CREG5 = 0.1F, CVCC = 1F, RRT = 100k, NDRV_ = floating, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER CS Input Bias Current CS Blanking Time SYMBOL IB_CL CONDITIONS VCS = 0V MIN 0 tCS_BLANK Propagation Delay from Comparator Input to NDRV_ tPD_CL TYP 50mV overdrive MAX UNITS +2 A 70 ns 40 ns IN CLAMP VOLTAGE IN Clamp Voltage VIN_CLAMP IN sinking 2mA (Note 2) 24.0 26.0 29.0 V ERROR AMPLIFIER (FB, COMP) Voltage Gain AV RCOMP = 100k to AGND 80 dB Unity-Gain Bandwidth BW RCOMP = 100k to AGND, CLOAD = 100pF to AGND 5 MHz Phase Margin PM RCOMP = 100k to AGND, CLOAD = 100pF to AGND 65 Degrees FB Input Offset Voltage VOS_FB COMP Clamp Voltage VCOMP Error-Amplifier Output Current ICOMP 3 High 2.6 3.8 Low 0.4 1.1 Sinking or sourcing 0.5 mV V mA +25C TA +125C (Note 3) 1.215 1.230 1.245 -40C TA +125C (Note 3) 1.205 1.230 1.242 300 Reference Voltage VREF Input Bias Current IB_EA 100 ICOMP_SC 12 mA TSD +170 C THYST 25 C COMP Short-Circuit Current V nA THERMAL SHUTDOWN Thermal-Shutdown Temperature Thermal Hysteresis OSCILLATOR SYNC INPUT (MAX5069A/D only) SYNC High-Level Voltage VIH_SYNC SYNC Low-Level Voltage VIL_SYNC SYNC Input Bias Current IB_SYNC Maximum SYNC Frequency fSYNC 2.4 V 0.4 10 fOSC = 2.5MHz (Note 4) V nA 3.125 MHz SYNC High-Level Pulse Width tSYNC_HI 30 ns SYNC Low-Level Pulse Width tSYNC_LO 30 ns DIGITAL SOFT-START Soft-Start Duration tSS Reference-Voltage Step (Note 5) VSTEP Reference-Voltage Steps During Soft-Start 2047 Cycles 9.7 mV 127 Steps OSCILLATOR Oscillator Frequency Range fOSC fOSC = (1011 / RRT) 50 2500 kHz _______________________________________________________________________________________ 3 MAX5069 ELECTRICAL CHARACTERISTICS (continued) MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers ELECTRICAL CHARACTERISTICS (continued) (VIN = +12V for the MAX5069C/D, VIN = +23.6V for the MAX5069A/B at startup, then reduces to +12V, CIN = CREG5 = 0.1F, CVCC = 1F, RRT = 100k, NDRV_ = floating, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS NDRV_ Switching Frequency fSW fSW = 1011 / (2 x RRT) RT Voltage VRT 40k < RRT < 500k TA = +25C Oscillator Accuracy TA = -40C to +125C Maximum Duty Cycle DMAX MIN TYP 25 MAX UNITS 1250 kHz 2.0 V fOSC 500kHz -2.5 +2.5 fOSC > 500kHz -4 +4 fOSC 500kHz -4.5 +4.5 fOSC > 500kHz -6 % +6 DT connected to REG5 100 % RDT = 24.9k 60 ns DEAD-TIME CONTROL (DT) Dead Time Dead-Time Disable Voltage Dead-Time Regulation Voltage tDT VREG5 0.5V VDT_DISABLE VDT V 1.23 V INTEGRATING FAULT PROTECTION (FLTINT) FLTINT Source Current IFLTINT VFLTINT = 0V 60 A FLTINT Shutdown Threshold VFLTINT_SD VFLTINT rising 2.8 V FLTINT Restart Threshold VFLTINT_RS VFLTINT falling 1.6 V CSLOPE = 100pf, RT = 110k 15 mV/s SLOPE COMPENSATION Slope Compensation VSLOPE Slope-Compensation Range VSLOPER 0 90 mV/s Slope-Compensation Voltage Range VSCOMP 0 2.7 V Note 1: The MAX5069 is 100% tested at TA = +25C. All limits over temperature are guaranteed by design. Note 2: The MAX5069A/B are intended for use in universal-input power supplies. The internal clamp circuit is used to prevent the bootstrap capacitor (C1 in Figure 1) from charging to a voltage beyond the absolute maximum rating of the device when UVLO/EN is low. The maximum current to VIN (hence to clamp) when UVLO is low (device is in shutdown) must be externally limited to 2mA. Clamp currents higher than 2mA may result in clamp voltages higher than 30V, thus exceeding the absolute maximum rating for VIN. For the MAX5069C/D, do not exceed the 24V maximum operating voltage of the device. Note 3: Reference voltage (VREF) is measured with FB connected to COMP (see the Functional Diagram). Note 4: The SYNC frequency must be at least 25% higher than the programmed oscillator frequency. Note 5: The internal oscillator clock cycle. 4 _______________________________________________________________________________________ High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers MAX5069A/B 21.5 UVLO/EN WAKE-UP THRESHOLD vs. TEMPERATURE MAX5069A/B 1.245 9.9 MAX5069 toc03 10.0 MAX5069 toc01 21.6 BOOTSTRAP UVLO SHUTDOWN LEVEL vs. TEMPERATURE MAX5069 toc02 BOOTSTRAP UVLO WAKE-UP LEVEL vs. TEMPERATURE UVLO/EN RISING 1.240 21.4 UVLO/EN (V) VIN (V) VIN (V) 9.8 21.3 9.7 1.235 1.230 21.2 9.6 21.0 9.5 10 35 60 85 110 1.220 -40 -15 10 35 60 85 110 -40 60 85 110 UVLO/EN SHUTDOWN THRESHOLD vs. TEMPERATURE VIN SUPPLY CURRENT IN UNDERVOLTAGE LOCKOUT vs. TEMPERATURE VIN SUPPLY CURRENT AFTER STARTUP vs. TEMPERATURE UVLO/EN FALLING 60 VIN = 19V WHEN IN BOOTSTRAP UVLO (MAX5069A/B) UVLO/EN (MAX5069C/D) IS LOW 56 8 fSW = 1.25MHz VIN = 24V 7 6 1.15 1.14 52 IIN (mA) 1.16 ISTART (A) 48 1.13 fSW = 500kHz 5 fSW = 250kHz 4 3 1.12 44 2 1.11 fSW = 100kHz fSW = 50kHz 1.10 40 10 35 60 85 110 -15 10 35 60 85 TEMPERATURE (C) VCC vs. TEMPERATURE REG5 OUTPUT VOLTAGE vs. OUTPUT CURRENT 10.0 9.7 VIN = 19V, IIN = 10mA VIN = 19V, IIN = 25mA 9.4 -40 TEMPERATURE (C) 4.980 RRT = 100k 4.975 9.1 110 -40 4.99 -40 -15 10 35 60 TEMPERATURE (C) 85 110 100A LOAD 1mA LOAD 4.95 4.94 4.92 4.955 4.91 4.90 4.950 7.0 110 4.93 VIN = 10.8V, IIN = 10mA VIN = 10.8V, IIN = 25mA 85 VIN = 10.8V 4.96 4.965 4.960 7.3 60 4.97 8.2 7.6 35 4.98 REG5 (V) REG5 (V) 8.5 10 REG5 vs. TEMPERATURE 5.00 4.970 8.8 -15 TEMPERATURE (C) MAX5069 toc08 -15 MAX5069 toc07 -40 1 MAX5069 toc09 UVLO/EN (V) 35 TEMPERATURE (C) 1.17 VCC (V) 10 TEMPERATURE (C) 1.18 7.9 -15 TEMPERATURE (C) MAX5069 toc05 1.19 -15 MAX5069 toc04 -40 1.20 1.225 MAX5069 toc06 21.1 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 OUTPUT CURRENT (mA) -40 -15 10 35 60 85 110 TEMPERATURE (C) _______________________________________________________________________________________ 5 MAX5069 Typical Operating Characteristics (VIN = +23.6V for MAX5069A/B at startup, then reduces to +12V, VIN = +12V for the MAX5069C/D, CIN = CREG5 = 0.1F, CVCC = 1F, RRT = 100k, NDRV_ = floating, VFB = 0V, VCOMP = floating, VCS = 0V, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (VIN = +23.6V for MAX5069A/B at startup, then reduces to +12V, VIN = +12V for the MAX5069C/D, CIN = CREG5 = 0.1F, CVCC = 1F, RRT = 100k, NDRV_ = floating, VFB = 0V, VCOMP = floating, VCS = 0V, TA = +25C, unless otherwise noted.) CS TRIP THRESHOLD vs. TEMPERATURE 4.982 4.981 4.980 4.979 4.978 318 315 312 309 fSW = 500kHz 525 +3 510 505 MEAN 500 -3 495 306 4.976 303 485 4.975 300 -40 480 -40 12 14 16 18 20 22 -15 10 35 60 85 490 110 10 -15 35 60 110 85 VIN (V) TEMPERATURE (C) TEMPERATURE (C) PROPAGATION DELAY FROM CS COMPARATOR INPUT TO NDRV vs. TEMPERATURE INPUT CURRENT vs. INPUT CLAMP VOLTAGE INPUT CLAMP VOLTAGE vs. TEMPERATURE INPUT CURRENT (mA) 46 12 44 42 40 38 36 10 8 6 4 34 26.6 26.4 26.2 26.0 25.8 25.6 -40 -15 10 35 60 85 25.2 25.0 0 110 -40 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 -15 10 35 60 85 110 INPUT CLAMP VOLTAGE (V) TEMPERATURE (C) NDRVA/NDRVB OUTPUT IMPEDANCE vs. TEMPERATURE NDRVA/NDRVB OUTPUT IMPEDANCE vs. TEMPERATURE ERROR AMPLIFIER OPEN-LOOP GAIN AND PHASE vs. FREQUENCY 4.0 MAX5069 toc16 2.6 3.8 3.6 3.4 2.2 3.2 RON () 2.4 2.0 1.8 VIN = 24V SOURCING 25mA 2.8 2.6 1.4 2.4 1.2 2.2 2.0 1.0 -40 -15 10 35 60 TEMPERATURE (C) 85 110 100 -30 GAIN -60 60 40 -90 PHASE 20 -120 0 -150 -20 -180 -40 -40 -15 10 35 60 TEMPERATURE (C) 85 110 30 0 80 3.0 1.6 MAX5069 toc18 120 GAIN (dB) VIN = 24V SINKING 100mA MAX5069 toc17 TEMPERATURE (C) -210 0.1 10 1k 100k FREQUENCY (Hz) _______________________________________________________________________________________ 10M PHASE (DEGREES) 30 2.8 ISINK = 2mA 26.8 25.4 2 32 3.0 27.0 MAX5069 toc15 48 INPUT CLAMP VOLTAGE (V) 14 MAX5069 toc13 50 PROPAGATION DELAY (ns) 24 TOTAL NUMBER OF DEVICES = 200 520 515 4.977 10 6 530 MAX5069 toc12 324 321 MAX5069 toc14 REG5 (V) 327 CS TRIP THRESHOLD (mV) 4.983 MAX5069 toc11 IREG5 = 100A 4.984 330 MAX5069 toc10 4.985 SWITCHING FREQUENCY vs. TEMPERATURE SWITCHING FREQUENCY (kHz) REG5 OUTPUT VOLTAGE vs. VIN RON () MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers VIN = 24V SINKING 50mA 12.0 11.0 62.5 62.4 10.5 10.0 62.3 9.5 62.2 9.0 62.1 8.5 8.0 62.0 -15 10 35 60 85 -15 10 60 85 TEMPERATURE (C) TEMPERATURE (C) 35 110 0.03 50.8 50.4 50.0 49.6 49.2 48.8 504 MAX5069 toc23 51.2 NDRV SWITCHING FREQUENCY (kHz) fSW = 50kHz 1 2 NDRV SWITCHING FREQUENCY vs. TEMPERATURE 505 MAX5069 toc22 52.0 0.1 RRT (M) NDRV SWITCHING FREQUENCY vs. TEMPERATURE NDRV SWITCHING FREQUENCY vs. TEMPERATURE 51.6 0.1 0.01 -40 110 fSW = 500kHz 503 502 501 500 499 498 497 1.40 NDRV SWITCHING FREQUENCY (kHz) -40 fSW = 1.25MHz 1.35 1.30 1.25 1.20 1.15 496 48.4 495 48.0 -15 10 35 60 85 1.10 -50 110 TEMPERATURE (C) -25 0 25 50 75 TEMPERATURE (C) 125 100 DEAD TIME vs. TEMPERATURE 65 VIN = 24V RDT = 24.9k RRT = 100k -15 10 35 60 85 110 DEAD TIME vs. RDT 200 MAX5069 toc26 70 -40 TEMPERATURE (C) MAX5069 toc25 180 160 140 60 TIME (ns) -40 TIME (ns) NDRV SWITCHING FREQUENCY (kHz) 1 MAX5069 toc24 11.5 62.6 RON () 62.7 2 fSW (MHz) 62.8 12.5 MAX5069 toc20 62.9 FLTINT CURRENT (A) 13.0 MAX5069 toc19 63.0 NDRVA SWITCHING FREQUENCY (fSW) vs. RRT HYST RON vs. TEMPERATURE MAX5069 toc21 FLTINT CURRENT vs. TEMPERATURE 55 50 120 100 80 60 40 45 20 40 0 -40 -15 10 35 60 TEMPERATURE (C) 85 110 1 10 100 RDT (k) _______________________________________________________________________________________ 7 MAX5069 Typical Operating Characteristics (continued) (VIN = +23.6V for MAX5069A/B at startup, then reduces to +12V, VIN = +12V for the MAX5069C/D, CIN = CREG5 = 0.1F, CVCC = 1F, RRT = 100k, NDRV_ = floating, VFB = 0V, VCOMP = floating, VCS = 0V, TA = +25C, unless otherwise noted.) MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers Pin Description PIN MAX5069A MAX5069D MAX5069B MAX5069C NAME FUNCTION 1 1 RT Oscillator-Timing Resistor. Connect a resistor from RT to AGND to set the internal oscillator frequency. 2 -- SYNC 8 External-Clock Sync Input. Connect SYNC to AGND when not using an external clock. -- 2 HYST 3 3 SCOMP Hysteresis Input 4 4 DT 5 5 UVLO/EN 6 6 FB 7 7 COMP Error-Amplifier Output Fault-Integration Input. A capacitor connected to FLTINT charges with an internal 60A current source during persistent current-limit faults. Switching terminates when VFLTINT is 2.8V. An external resistor connected in parallel discharges the capacitor. Switching resumes when VFLTINT drops to 1.6V. Slope-Compensation Capacitor Connection Dead-Time Resistor Connection. Connect a resistor from DT to AGND to program the output dead time. Connect to REG5 for NDRVA and NDRVB maximum 50% duty cycle. Externally Programmable Undervoltage Lockout. UVLO/EN programs the input start voltage. Connect UVLO/EN to AGND to disable the output. Error-Amplifier Inverting Input 8 8 FLTINT 9 9 CS Current-Sense Resistor Connection 10 10 AGND Analog Ground. Connect to PGND. 11 11 PGND Power Ground. Connect to AGND through a ground plane. 12 12 NDRVB Gate-Driver Output B. Connect NDRVB to the gate of the external N-channel FET. 13 13 NDRVA Gate-Driver Output A. Connect NDRVA to the gate of the external N-channel FET. 14 14 VCC 9V Linear-Regulator Output. Decouple VCC with a minimum 1F ceramic capacitor to AGND; also internally connected to the FET drivers. 15 15 IN Power-Supply Input. IN provides power for all internal circuitry except the gate driver. Decouple IN with 0.1F to AGND (see the Typical Operating Circuit). 16 16 REG5 5V Linear-Regulator Output. Decouple REG5 to AGND with 0.1F ceramic capacitor. EP EP PAD Exposed Paddle. Connect to GND. _______________________________________________________________________________________ High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers The MAX5069 is a current-mode, dual MOSFET driver, PWM controller designed for isolated and nonisolated push-pull or half-/full-bridge power-supply applications. A bootstrap UVLO with a programmable hysteresis, very low startup, and low operating current result in high-efficiency universal-input power supplies. In addition to the internal bootstrap UVLO, the device also offers programmable input startup and turn-off voltages, programmed through the UVLO/EN pin. The MAX5069 includes a cycle-by-cycle current limit that turns off the gate drive to the external MOSFET during an overcurrent condition. The MAX5069 integrating fault protection reduces average power dissipation during persistent fault conditions (see the Integrating Fault Protection section). The MAX5069 features a very accurate, wide-range, programmable oscillator that simplifies and optimizes the design of the magnetics. The MAX5069A/B are well suited for universal-input (rectified 85VAC to 265VAC) or telecom (-36VDC to -72VDC) power supplies. The MAX5069C/D are well suited for low-input voltage (10.8VDC to 24VDC) power supplies. The MAX5069 high-frequency, universal input, offline/telecom, current-mode PWM controller integrates all the building blocks necessary for implementing ACDC and DC-DC fixed-frequency power supplies. Pushpull and half-/full-bridge isolated or nonisolated power supplies are easily constructed using either primary- or secondary-side regulation. Current-mode control with leading-edge blanking simplifies control-loop design and the programmable slope compensation stabilizes the current loop when operating both FET drivers at a combined 100% duty cycle. An input UVLO programs the input-supply startup voltage and ensures proper operation during brownout conditions. An external voltage-divider programs the supply startup voltage. The MAX5069B/C feature a programmable UVLO hysteresis. The MAX5069A/B feature an additional internal bootstrap UVLO with large hysteresis that requires a minimum startup voltage of 23.6V. The MAX5069A/D start up from a minimum voltage of 10.8V. Internal digital soft-start reduces output-voltage overshoot at startup. A single external resistor programs the switching frequency of each MOSFET driver from 25kHz to 1.25MHz. The MAX5069A/D provide a SYNC input for synchronization to an external clock. The maximum FET driver duty cycle for each driver is limited to 50%. Programmable dead time allows additional flexibility in optimizing magnetic design and overcoming parasitic effects. Integrating fault protection ignores transient overcurrent conditions for a set length of time. The length of time is programmed by an external capacitor. The internal thermal-shutdown circuit protects the device should the junction temperature exceed +170C. Power supplies designed with the MAX5069A/B use a high-value startup resistor, R1, which charges a reservoir capacitor, C1 (Figure 1). During this initial period, while the voltage is less than the internal bootstrap UVLO threshold, the device typically consumes only 47A of quiescent current. This low startup current and the large bootstrap UVLO hysteresis help to minimize the power dissipation across R1 even at the high end of the universal AC input voltage (265VAC). The MAX5069 includes a cycle-by-cycle current limit that turns off the gates to both external MOSFETs during an overcurrent condition. When using the MAX5069A/B in the bootstrap mode (if the power-supply output is shorted), the tertiary winding voltage drops below the 9.74V threshold, causing the UVLO to turn off the gate to the external power MOSFETs. This reinitiates a startup sequence with soft-start. Current-Mode Control The MAX5069 offers a current-mode control operation feature, such as leading-edge blanking with a dual internal path that only blanks the sensed current signal applied to the input of the PWM controller. The currentlimit comparator monitors CS at all times and provides cycle-by-cycle current limit without being blanked. The leading-edge blanking of the CS signal prevents the PWM comparator from prematurely terminating the on cycle. The CS signal contains a leading-edge spike that results from the MOSFET's gate charge current, and the capacitive and diode reverse-recovery current of the power circuit. Since this leading-edge spike is normally lower than the current-limit comparator threshold, current limiting is provided under all conditions. Use the MAX5069 in push-pull and half-/full-bridge applications where a large duty cycle is desired. The large duty cycle results in much lower operating primary RMS currents through the MOSFET switches, and in most cases it results in a smaller inductor and output filter capacitor. The MAX5069 adjusted slope compensation allows for easy stabilization of the inner current loop. _______________________________________________________________________________________ 9 MAX5069 Detailed Description MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers D3 D1 VOUT C7 VIN R1 C1 R6 R2 IN D2 UVLO/EN C2 FLTINT RHYST C3 HYST VCC C4 R9 R7 MAX5069B REG5 R3 RT NDRVB Q2 NDRVA R4 R10 Q1 DT CS C5 SCOMP FB R8 AGND PGND COMP R5 C6 Figure 1. Nonisolated Power Supply with Programmable Input Supply Voltage Undervoltage Lockout The MAX5069 features an input voltage UVLO/EN function to enable the PWM controller before any operation can begin. The MAX5069A/D shut down if the voltage at UVLO/EN falls below its 1.18V threshold. The MAX5069B/C also incorporate a UVLO hysteresis input to set the desired turn-off voltage. MAX5069A/D UVLO Adjustment The MAX5069A/D have an input voltage UVLO/EN with a 1.231V threshold. Before any operation can commence, the UVLO/EN voltage must exceed the 1.231V threshold. The UVLO circuit keeps the PWM comparator, ILIM comparator, oscillator, and output drivers shutdown to reduce current consumption (see the Functional Diagram). 10 Calculate R6 in Figure 2 by using the following formula: V R6 = ON - 1 x R7 V ULR2 where VULR2 is the UVLO/EN's 1.231V rising threshold and VON is the desired startup voltage. Choose an R7 value in the 20k range. After a successful startup, the MAX5069A/D shut down if the voltage at UVLO/EN drops below its 1.18V falling threshold. MAX5069B/C UVLO with Programmable Hysteresis In addition to programmable undervoltage lockout during startup, the MAX5069B/C incorporate a UVLO/EN ______________________________________________________________________________________ High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers MAX5069 VIN MAX5069A/D R6 UVLO/EN VHYST = VON - VOFF R7 1.23V 1.18V VOFF Figure 2. Setting the MAX5069A/D Undervoltage Lockout Threshold hysteresis that allows the user to set a voltage (VOFF) to disable the controller (see Figure 3). At the beginning of the startup sequence, UVLO/EN is below the 1.23V threshold, and Q1 turns on connecting RHYST to GND (Figure 4). Once the UVLO 1.23V threshold is crossed, Q1 turns off, resulting in the series combination of R6, RHYST, and R7, placing the MAX5069 in normal operating condition. Calculate the turn-on voltage (V ON) by using the following formula: V R6 = ON - 1 x RHYST VULR2 VON Figure 3. MAX5069 Hysteresis VIN MAX5069B/C R6 UVLO/EN RHYST 1.23V 1.18V HYST Q1 R7 where VULR2 is the UVLO/EN's 1.23V rising threshold. Choose an RHYST value in the 20k range. The MAX5069 turns off when the MAX5069 UVLO/EN falls below the 1.18V falling threshold. The turn-off voltage (VOFF) is then defined as: V R7 = R6 / OFF - 1 - RHYST VULF2 where VULF2 is the 1.18V UVLO/EN falling threshold. Bootstrap Undervoltage Lockout (MAX5069A/B) In addition to the externally programmable UVLO function offered by the MAX5069, the MAX5069A/B feature an additional internal bootstrap UVLO for use in highvoltage power supplies (see the Functional Diagram). This allows the device to bootstrap itself during initial Figure 4. Setting the MAX5069B/C Turn-On/Turn-Off Voltages power-up. The MAX5069A/B start when VIN exceeds the bootstrap UVLO threshold of 23.6V. During startup, the UVLO circuit keeps the PWM comparator, ILIM comparator, oscillator, and output drivers shut down to reduce current consumption. Once V IN reaches 23.6V, the UVLO circuit turns on both the PWM and ILIM comparators, as well as the oscillator, and allows the output driver to switch. If VIN drops below 9.7V, the UVLO circuit shuts down the PWM comparator, ILIM comparator, oscillator, and output drivers, returning the MAX5069A/B to the startup mode. ______________________________________________________________________________________ 11 MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers MAX5069A/B Startup Operation Normally, VIN is derived from the tertiary winding of the transformer. However, at startup there is no energy delivered through the transformer; hence, a special bootstrap sequence is required. Figure 5 shows the voltages on VIN and VCC during startup. Initially, both VIN and VCC are 0V. After the input voltage is applied, C1 charges through the startup resistor, R1, to an intermediate voltage (see Figure 1). At this point, the internal regulator begins charging C3 (see Figure 5). Only 47A of the current supplied by R1 is used by the MAX5069A/B. The remaining input current charges C1 and C3. The charging of C3 stops when the VCC voltage reaches approximately 9.5V. The voltage across C1 continues rising until it reaches the wake-up level of 23.6V. Once VIN exceeds the bootstrap UVLO threshold, NDRVA/NDRVB begin switching the MOSFETs and energy is transferred to the secondary and tertiary outputs. If the voltage on the tertiary output builds to higher than 9.74V (the bootstrap UVLO lower threshold), startup ends and sustained operation commences. If VIN drops below 9.74V before startup is complete, the device goes back to low-current UVLO. If this occurs, increase the value of C1 to store enough energy to allow for the voltage at the tertiary winding to build up. Startup Time Considerations for Power Supplies Using the MAX5069A/B The VIN bypass capacitor, C1, supplies current immediately after wakeup (see Figure 1). The size of C1 and the connection configuration of the tertiary winding determine the number of cycles available for startup. Large values of C1 increase the startup time and also supply extra gate charge for more cycles during initial startup. If the value of C1 is too small, VIN drops below 9.74V because NDRVA/NDRVB do not have enough time to switch and build up sufficient voltage across the tertiary output that powers the device. The device goes back into UVLO and does not start. Use low-leakage capacitors for C1 and C3. Generally, offline power supplies keep typical startup times to less than 500ms, even in low-line conditions (85VAC input for universal offline applications or 36VDC for telecom applications). Size the startup resistor, R1, to supply both the maximum startup bias of the device (90A) and the charging current for C1 and C3. The bypass capacitor, C3, must charge to 9.5V, and C1 must charge to 24V, within the desired time period of 500ms. Because of the internal soft-start time of the MAX5069, C1 must store enough charge to deliver current to the device for at least 2047 oscillator clock cycles. To calculate the approximate amount of capacitance required, use the following formula: 12 VCC 2V/div MAX5069 VIN PIN 5V/div 0V 100ms/div Figure 5. V IN and V CC During Startup When Using the MAX5069 in Bootstrapped Mode (See Figure 1) Ig = Qgtot x fSW (IIN + Ig ) x t SS C1 = VHYST where IIN is the MAX5069's internal supply current after startup (3.3mA, typ), Qgtot is the total gate charge for Q1 and Q2, fSW is the MAX5069's programmed output switching frequency, VHYST is the bootstrap UVLO hysteresis (12V), and tss is the internal soft-start time (2047 clock cycles x 1 / fOSC). Example: Ig = (16nC) (250kHz) 4mA fOSC = 500kHz tSS = 2047 x (1 / fOSC) = 4.1ms C1 = (3.3mA + 4mA) (4.1ms) = 2.5F 12V Use a 4.7F ceramic capacitor for C1. Assuming C1 > C3, calculate the value of R1 as follows: VSUVR x C1 500ms VIN(MIN) - 0.5 x VSUVR IC1 R1 IC1 + ISTART where V SUVR is the bootstrap UVLO wakeup level (23.6V max), VIN(MIN) is the minimum input supply voltage for the application (36V for telecom), and ISTART is the VIN supply current at startup (90A, max). ______________________________________________________________________________________ High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers MAX5069 VOUT C7 VIN R1 C1 R6 R2 IN C2 UVLO/EN FLTINT C3 VCC RHYST MAX5069B HYST R7 C4 REG5 NDRVB R3 Q2 RT NDRVA Q1 R4 DT CS SCOMP FB C5 AGND R12 R8 C8 VCC PGND COMP R5 C10 C6 R13 PS2913 R10 R9 R11 MAX8515 R14 Figure 6. Secondary-Side, Regulated, Isolated Power Supply For example: 24V x 4.7F = 225A 500ms 36V - 12V R1 = 76k 225A + 90A IC1 = To minimize power loss on this resistor, choose a higher value for R1 than the one calculated above (if a longer startup time can be tolerated). The above startup method applies to a circuit similar to the one shown in Figure 1. In this circuit, the tertiary winding has the same phase as the secondary windings. Thus, the voltage on the tertiary winding at any given time is proportional to the output voltage. The minimum discharge time of C1 from 22V to 10V must be greater than the soft-start time (tSS). ______________________________________________________________________________________ 13 MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers Oscillator/Switching Frequency Use an external resistor at RT to program the MAX5069 internal oscillator frequency from 50kHz to 2.5MHz. The MAX5069 NDRVA/NDRVB switching frequency is one half of the programmed oscillator frequency with a maximum 50% duty cycle. Use the following formula to calculate the internal oscillator frequency: fosc = Dead time = 11 10 RRT 60 x RDT (ns) 29.4 where RDT is in k and the dead time is in ns. where fOSC is the oscillator frequency and RRT is a resistor connected from RT to AGND. Choose the appropriate resistor at RT to calculate the desired switching frequency (fSW): RRT = shorting out the transformer's primary. The MAX5069 allows the dead-time delay required to turn on the NDRVB FET after the NDRVA FET turns off. The dead time can be programmed to a minimum of 30ns to 1 / (0.5 x fSW). Connect a resistor between DT and AGND to set the desired dead time. Calculate the dead time using the following formula: 1011 2fSW For the maximum 50% duty cycle at NDRVA/NDRVB, connect DT to REG5. Dual N-Channel MOSFET Switch Driver The MAX5069 drives two external N-channel MOSFETs in push-pull isolated power supplies. Each MOSFET driver operates with a maximum 50% duty cycle. The NDRV_ outputs are supplied by the internal regulator (VCC), which is internally set to approximately 9.5V. For the universal input voltage range, the MOSFETs used must be able to withstand at least twice the DC level of the high-line input voltage. Both NDRVA and NDRVB can source and sink in excess of 650mA and 1000mA peak current, respectively. Dead-Time Control In typical push-pull designs, it is desirable to add some extra delay between the turning off of one MOSFET and the turning on of the next MOSFET (Figure 7). The extra time ensures that the first MOSFET is fully off when the other MOSFET starts to turn on. This prevents both MOSFETs from being on simultaneously, thus avoiding External Synchronization (MAX5069A/D) The MAX5069A/D can be synchronized using an external clock at the SYNC input. For proper frequency synchronization, the SYNC's input frequency must be at least 25% higher than the MAX5069A/D programmed internal oscillator frequency. Connect SYNC to AGND when not using an external clock. Integrating Fault Protection The integrating fault-protection feature allows transient overcurrent conditions to be ignored for a programmable amount of time, giving the power supply time to behave like a current source to the load. For example, this can occur under load-current transients when the control loop requests maximum current to keep the output voltage from going out of regulation. Program the fault-integration time by connecting an external suitably sized capacitor to the FLTINT. Under sustained overcurrent faults, the voltage across this capacitor ramps up towards the FLTINT shutdown threshold (typically 2.8V). Once the threshold is reached, the power supply shuts down. A high-value bleed resistor connected in parallel with the FLTINT capacitor allows it to discharge towards the restart threshold (typically 1.6V). Once this threshold is reached, the supply restarts with a new soft-start cycle. SYNC MAX5069A/D tDT DEAD TIME NDRVA NDRVB RT <50% PWM PWM Figure 7. MAX5069 Dead-Time Timing Diagram 14 <50% AGND Figure 8. External Synchronization of the MAX5069A/D ______________________________________________________________________________________ High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers I x tSH CFLTINT FLTINT 2.8V where IFLTINT = 60A, tSH is the desired fault-integration time during which current-limit events from the current-limit comparator are ignored. For example, a 0.1F capacitor gives a fault-integration time of 4.7ms. This is an approximate formula. Some testing may be required to fine-tune the actual value of the capacitor. To calculate the recovery time, use the following formula: RFLTINT t RT 0.595 x CFLTINT Error Amplifier The MAX5069 includes an internal error amplifier that can regulate the output voltage in the case of a nonisolated power supply (Figure 1). Calculate the output voltage using the following equation: R9 VOUT = 1 + x VREF R10 where VREF = 1.23V. The amplifier's noninverting input internally connects to a digital soft-start reference voltage. This forces the output voltage to come up in an orderly and well-defined manner under all load conditions. Slope Compensation The MAX5069 uses an internal-ramp generator for slope compensation. The internal-ramp signal resets at the beginning of each cycle and slews at the rate programmed by the external capacitor connected at SCOMP and the resistor at RT. Adjust the MAX5069 slew rate up to 90mV/s using the following equation: SR = where tRT is the desired recovery time. Choose tRT = 10 x tSH. Typical values for tSH range from a few hundred microseconds to a few milliseconds. Soft-Start The MAX5069 soft-start feature allows the load voltage to ramp up in a controlled manner, eliminating outputvoltage overshoot. Soft-start begins after UVLO is deasserted. The voltage applied to the noninverting node of the amplifier ramps from 0 to 1.23V in 2047 oscillator clock cycles (soft-start timeout period). Unlike other devices, the MAX5069 reference voltage to the internal amplifier is soft-started. This method results in superior control of the output voltage under heavy- and light-load conditions. Internal Regulators Two internal linear regulators power the MAX5069 internal and external control circuits. VCC powers the external N-channel MOSFETs and is internally set to approximately 9.5V. The REG5 5V regulator has a 1mA sourcing capability and may be used to provide power to external circuitry. Bypass VCC and REG5 with 1F and 0.1F high quality capacitors, respectively. Use lower value ceramics in parallel to bypass other unwanted noise signals. Bootstrapped operation requires startup through a bleed resistor. Do not excessively load the regulators while the MAX5069 is in the power-up mode. Overloading the outputs may cause the MAX5069 to fail upon startup. 165 x 10 -6 (mV / s) RRT x CSCOMP where RRT is the external resistor at RT that sets the oscillator frequency and CSCOMP is the capacitor at SCOMP. PWM Comparator The PWM comparator uses the instantaneous current, the error amplifier, and the slope compensation to determine when to switch NDRVA and NDRVB off. In normal operation, the N-channel MOSFETs turns off when: IPRIMARY x RCS > VEA - VOFFSET - VSCOMP where IPRIMARY is the current through the N-channel MOSFETs, V EA is the output voltage of the internal amplifier, VOFFSET is the 1.6V internal DC offset, and VSCOMP is the ramp function starting at zero and slewing at the programmed slew rate (SR). When using the MAX5069 in a forward-converter configuration, the following conditions must be met to avoid current-loop subharmonic oscillations: K x RCS x VOUT NS x = SR L NP where K = 0.75 and NS and NP are the number of turns on the secondary and primary side of the transformer, respectively. L is the secondary filter inductor. When optimally compensated, the current loop responds to input-voltage transients within one cycle. ______________________________________________________________________________________ 15 MAX5069 Note that cycle-by-cycle current limiting is provided at all times by CS with a threshold of 314mV (typ). The fault-integration circuit forces a 60A current onto FLTINT each time that the current-limit comparator is tripped (see the Functional Diagram). Use the following formula to calculate the value of the capacitor necessary for the desired shutdown time of the circuit: MAX5069 High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers Current Limit Applications Information The current-sense resistor (RCS), connected between the source of the MOSFET and ground, sets the current limit. The CS input has a voltage trip level (V CS) of 314mV. Use the following equation to calculate the value of RCS: RCS = Layout Recommendations Keep all PC board traces carrying switching currents as short as possible, and minimize current loops. For universal AC input design, follow all applicable safety regulations. Offline power supplies may require UL, VDE, and other similar agency approvals. Contact these agencies for the latest layout and component rules. Typically, there are two sources of noise emission in a switching power supply: high di/dt loops and high dV/dt surfaces. For example, traces that carry the drain current often form high di/dt loops. Similarly, the heatsink of the MOSFET presents a dV/dt source, thus minimize the surface area of the heatsink as much as possible. To achieve best performance and to avoid ground loops, use a solid ground-plane connection. VCS IPRI where IPRI is the peak current in the primary that flows through the MOSFET at full load. When the voltage produced by this current (through the current-sense resistor) exceeds the current-limit comparator threshold, the MOSFET drivers (NDRVA/ NDRVB) quickly terminate the current on-cycle. In most cases, a small RC filter is required to filter out the leading-edge spike on the sense waveform. Set the corner frequency to a few MHz above the switching frequency. Selector Guide 16 PART BOOTSTRAP UVLO STARTUP VOLTAGE (V) PROGRAMMABLE UVLO HYSTERESIS OSCILLATOR SYNC MAX5069A Yes 23.6 No Yes MAX5069B Yes 23.6 Yes No MAX5069C No 10.8 Yes No MAX5069D No 10.8 No Yes ______________________________________________________________________________________ R5 R19 C8 R8 C11 C10 PGND R4 R3 MAX5069B PGND FB R10 FLTINT CS AGND NDRVB HYST COMP NDRVA VCC IN REG5 DT SCOMP UVLO/EN RT C12 C1 PGND PGND REG5 C13 PGND PGND C14 R20 PGND R13 R12 R11 C2 C3 R14 PGND R16 Q2 Si7450DP Q1 Si7450DP C4 D5 N4148 D4 N4148 D3 N4148 D2 N4148 R15 R17 6T 6T T1 R21 3T 3T VCC D1 25CTQ45 PS2911 L1 10H C15 C5 C7 C17 OUT IN FB GND MAX8515AEZK-T R17 C16 PGND C6 R2 R1 VOUT 12V UP TO 15A Typical Operating Circuit ______________________________________________________________________________________ 17 MAX5069 L2 1mH High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers MAX5069 Functional Diagram HYST** BOOTSTRAP UVLO MAX5069 UVLO/EN 21.6V/ 9.74V UVLO 1.23V REFERENCE 1.23V/ 1.18V IN VIN CLAMP 26V IN 2.8V/ 1.6V 60A REGULATOR Q FLTINT REG_OK R S 5V OUT REG5 VCC VCC CURRENT-LIMIT COMPARATOR S 314mV 5k + CS + * 1.6V Q NDRVA R 70ns BLANKING AGND PWM COMPARATOR NDRVB OSC PGND OUT THERMAL SHUTDOWN DEAD TIME SLOPE COMPENSATION SCOMP OUT 1.23V DIGITAL SOFT-START ERROR AMP FB *MAX5069A/D **MAX5069B/C COMP SYNC* RT DT Chip Information TRANSISTOR COUNT: 4266 PROCESS: BiCMOS 18 ______________________________________________________________________________________ High-Frequency, Current-Mode PWM Controller with Accurate Oscillator and Dual FET Drivers TSSOP 4.4mm BODY.EPS PACKAGE OUTLINE, TSSOP, 4.40 MM BODY EXPOSED PAD 21-0108 D 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19 (c) 2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. MAX5069 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)