1
Photoelectric sensors in M18 stainless steel housing
E3FC
Best durability for wash-down applications
• High grade steel housing (SUS316L)
• Withstands heat shock conditions
• Epoxy resin preventing water ingress if connector is not fixed properly
• Proven with various industrial detergents of Ecolab and Diversey
(Details see page 10)
• Bright visible red LED enabling easy alignment
Ordering Information
Sensors
*1. The set type includes the emitter and receiver.
*2. The Reflector is sold separately. Select the Reflector model most suited to the application.
Sensor type Sensing distance Connection method Model
NPN output PNP output
Through-beam pre-wired E3FC-TN11 2M *1 E3FC-TP11 2M *1
M12 connector E3FC-TN21 *1 E3FC-TP21 *1
Retro-reflective with MSR
function *2 pre-wired E3FC-RN11 2M E3FC-RP11 2M
M12 connector E3FC-RN21 E3FC-RP21
Diffuse-reflectivepre-wired E3FC-DN12 2M E3FC-DP12 2M
M12 connector E3FC-DN22 E3FC-DP22
pre-wired E3FC-DN13 2M E3FC-DP13 2M
M12 connector E3FC-DN23 E3FC-DP23
pre-wired E3FC-DN15 2M E3FC-DP15 2M
M12 connector E3FC-DN25 E3FC-DP25
pre-wired E3FC-DN16 2M E3FC-DP16 2M
M12 connector E3FC-DN26 E3FC-DP26
BGS
(background suppression) pre-wired E3FC-LN11 2M E3FC-LP11 2M
M12 connector E3FC-LN21 E3FC-LP21
pre-wired E3FC-LN12 2M E3FC-LP12 2M
M12 connector E3FC-LN22 E3FC-LP22
Transparent object detection
(co-axial retro-reflective with
MSR*2)
pre-wired E3FC-BN11 2M E3FC-BP11 2M
M12 connector E3FC-BN21 E3FC-BP21
Red light Infrared light
20 m
0.1 to 4 m
with E39-R1S
300 mm
1 m
300 mm
1 m
100 mm
200 mm
1
00 to 500 mm
with E39-RP1
E3FC
2
Reflectors [Refer to Dimensions on page 12.]
Reflectors required for Retro-reflective Sensors: A Reflector is not provided with the Sensor. Be sure to order a Reflector separately.
Mounting brackets [Refer to Dimensions on page 12.]
A Mounting Bracket is not enclosed with the Sensor. Order a Mounting Bracket separately if required.
Sensor I/O connectors
Models for Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.
Sensing distance Appearance Model Material Remarks
0.1 to 4 m E39-R1S ABS, PMMA IP67
0.1 to 4 m E39-R50 PET IP67, IP69K
Ecolab tested plastic material
0 to 500 mm E39-RP1 ABS, PMMA for E3FC-B, enhanced PET detection, IP67
0.1 to 2 m E39-R16 SUS316L, glass (window)
enhanced chemical resistance for pharma
industry
IP67, IP68, IP69K
Sensor Appearance Model (Material) Material Remarks
all types
E39-L183 SUS304 Mounting bracket
E39-EL16 SUS316L M18 Flush mounting nut
Sensor Model Material Appearance Cable type Model
M12 connector types Detergent resistant
connector cable
Cable: Detergent
resistant PVC
Connector:
SUS316L
2 m
4-wire
Y92E-S12PVC4S2M-L
5 m Y92E-S12PVC4S5M-L
2 m Y92E-S12PVC4A2M-L
5 m Y92E-S12PVC4A5M-L
Straight
Angle
3
E3FC
Ratings and Specifications
*1. L-On fixed output available for Diffuse reflective and BGS models. Please add "A" in order code (e.g. E3FC-DP11A 2M)
*2. IP68 Degree of Protection Specifications
IP68 is defined by heat shock resistance with 20 test cycles of 30 min. changing between 3° and 60° surface tensioned water.
*3. IP69K Degree of Protection Specifications
IP69K is a protection specification stipulated by DIN 40050 Part 9 of the German standards.
The test item is sprayed with 80C water from a nozzle of a specified shape at a water pressure of 80 to 100 bar. The amount of
water is 14 to 16 liters per minute.
The distance between the test item and the nozzle is 10 to 15 cm. The water is discharged at angles of 0, 30, 60, and 90 from
the horizontal plane for 30 seconds at each angle while the test item is rotated horizontally.
Sensing method Through-beam Retro-reflective with MSR function
Model NPN
output
Pre-wired E3FC-TN11 2M E3FC-RN11 2M
M12 Connector
E3FC-TN21 E3FC-RN21
PNP
output
Pre-wired E3FC-TP11 2M E3FC-RP11 2M
Item
M12 Connector
E3FC-TP21 E3FC-RP21
Sensing distance 20 m 0.1 to 4 m
(with E39-R1S)
Spot diameter (reference value) —
Standard sensing object Opaque: 7 mm dia.min. Opaque: 75 mm dia.min.
Differential travel —
Directional angle 2 min.
Light source (wavelength) Red LED (624 nm) Red LED (624 nm)
Power supply voltage 10 to 30 VDC (include voltage ripple of 10%(p-p) max.)
Current consumption 40 mA max.
(Emitter 25 mA max. Receiver 15 mA max.) 25 mA max.
Control output NPN/PNP (open collector)
Load current: 100 mA max. (Residual voltage: 3 V max.), Load power supply voltage: 30 VDC max.
Operation mode Light-ON/Dark-ON selectable by wiring *1.
Indicator
Operation indicator (orange)
Stability indicator (green)
Power indicator (green): only Emitter of Through-beam
Protection circuits
Power supply reverse polarity protection, Output short-circuit protection, and Output reverse polarity protection
Response time 0.5 ms
Sensitivity adjustment Fixed
Ambient illumination (Receiver side)
Incandescent lamp: 3,000 lx max./ Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55C/ Storage: -30 to 70C (with no icing or condensation)
Ambient humidity range Operating: 35 to 85%/ Storage: 35 to 95% (with no condensation)
Insulation resistance 20 M min. at 500 VDC
Dielectric strength 1,000 VAC at 50/60 Hz for 1 min. between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y and Z directions
Degree of protection IEC: IP67, IP68 *2., DIN 40050-9: IP69K *3.
Weight Pre-wired cable (2M) 152 g 76 g
Connector 44 g 22 g
Material
Case SUS 316L (1.4404)
Lens and Display PMMA
Adjuster –
Nut SUS 316L (1.4404)
Accessories Instruction sheet
M18 nuts (4 pcs)
Instruction sheet
M18 nuts (2 pcs)
E3FC
4
*1. L-On fixed output available for Diffuse reflective and BGS models. Please add "A" in order code (e.g. E3FC-DP11A 2M)
*2. IP68 Degree of Protection Specifications
IP68 is defined by heat shock resistance with 20 test cycles of 30 min. changing between 3° and 60° surface tensioned water.
*3. IP69K Degree of Protection Specifications
IP69K is a protection specification stipulated by DIN 40050 Part 9 of the German standards.
The test item is sprayed with 80C water from a nozzle of a specified shape at a water pressure of 80 to 100 bar. The amount of
water is 14 to 16 liters per minute.
The distance between the test item and the nozzle is 10 to 15 cm. The water is discharged at angles of 0, 30, 60, and 90 from
the horizontal plane for 30 seconds at each angle while the test item is rotated horizontally.
Sensing method Diffuse-reflective
Model NPN
output
Pre-wired
E3FC-DN12 2M E3FC-DN13 2M E3FC-DN15 2M E3FC-DN16 2M
M12 Connector
E3F
C
-DN22 E3F
C
-DN23 E3F
C
-DN25 E3F
C
-DN26
PNP
output
Pre-wired
E3FC-DP12 2M E3FC-DP13 2M E3FC-DP15 2M E3FC-DP16 2M
Item
M12 Connector
E3F
C
-DP22 E3F
C
-DP23 E3F
C
-DP25 E3F
C
-DP26
Sensing distance
300 mm
(white paper:
300 300 mm)
1 m
(white paper:
300 300 mm)
300 mm
(white paper:
300 300 mm)
1 m
(white paper:
300 300 mm)
Spot diameter (reference value)
40
50 mm
Sensing distance
of 300 mm
120
150 mm
Sensing distance
of 1 m
40
50 mm
Sensing distance
of 300 mm
120
150 mm
Sensing distance
of 1 m
Standard sensing object —
Differential travel 20% max.
Directional angle —
Light source (wavelength) Red LED (624 nm) Infrared LED (850 nm)
Power supply voltage 10 to 30 VDC (include voltage ripple of 10%(p-p) max.)
Current consumption 25 mA max.
Control output NPN/PNP (open collector)
Load current: 100 mA max. (Residual voltage: 3 V max.), Load power supply voltage: 30 VDC max.
Operation mode Light-ON/Dark-ON selectable by wiring *3.
Indicator Operation indicator (orange)
Stability indicator (green)
Protection circuits
Power supply reverse polarity protection, Output short-circuit protection, and Output reverse polarity protection
Response time 0.5 ms
Sensitivity adjustment One-turn adjuster
Ambient illumination
Incandescent lamp: 3,000 lx max./ Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55C/ Storage: -30 to 70C (with no icing or condensation)
Ambient humidity range Operating: 35 to 85%/ Storage: 35 to 95% (with no condensation)
Insulation resistance 20 M min. at 500 VDC
Dielectric strength 1,000 VAC at 50/60 Hz for 1 min. between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y and Z directions
Degree of protection IEC: IP67, IP68 *2., DIN 40050-9: IP69K *3.
Weight Pre-wired cable (2M) 76 g
Connector 22 g
Material
Case SUS 316L (1.4404)
Lens and Display PMMA
Adjuster POM
Nut SUS 316L (1.4404)
Accessories Instruction sheet
M18 nuts (2 pcs)
E3FC
5
*1. L-On fixed output available for Diffuse reflective and BGS models. Please add "A" in order code (e.g. E3FC-DP11A 2M)
*2. IP68 Degree of Protection Specifications
IP68 is defined by heat shock resistance with 20 test cycles of 30 min. changing between 3° and 60° surface tensioned water.
*3. IP69K Degree of Protection Specifications
IP69K is a protection specification stipulated by DIN 40050 Part 9 of the German standards.
The test item is sprayed with 80C water from a nozzle of a specified shape at a water pressure of 80 to 100 bar. The amount of
water is 14 to 16 liters per minute.
The distance between the test item and the nozzle is 10 to 15 cm. The water is discharged at angles of 0, 30, 60, and 90 from
the horizontal plane for 30 seconds at each angle while the test item is rotated horizontally.
Sensing method BGS (Background suppression) Transparent detected with
P-opaquing function
Model NPN
output
Pre-wired E3FC-LN11 2M E3FC-LN12 2M E3FC-BN11 2M
M12 Connector
E3FC-LN21 E3FC-LN22 E3FC-BN21
PNP
output
Pre-wired E3FC-LP11 2M E3FC-LP12 2M E3FC-BP11 2M
Item
M12 Connector
E3FC-LP21 E3FC-LP22 E3FC-BP21
Sensing distance
100 mm
(white paper:
300 300 mm)
200 mm
(white paper:
300 300 mm)
100 to 500 mm
(with E39-RP1)
Spot diameter (reference value) 10 10 mm
Sensing distance of 100 mm
10 15 mm
Sensing distance of 200 mm —
Standard sensing object — glass (t = 1.0 mm): 150 × 150 mm
Differential travel 20% max. —
Directional angle —
Light source (wavelength) Red LED (624 nm)
Power supply voltage 10 to 30 VDC (include voltage ripple of 10%(p-p) max.)
Current consumption 25 mA max.
Control output NPN/PNP (open collector)
Load current: 100 mA max. (Residual voltage: 3 V max.), Load power supply voltage: 30 VDC max.
Operation mode Light-ON/Dark-ON selectable by wiring *1.
Indicator Operation indicator (orange)
Stability indicator (green)
Protection circuits
Power supply reverse polarity protection, Output short-circuit protection, and Output reverse polarity protection
Response time 0.5 ms
Sensitivity adjustment Fixed One-turn adjuster
Ambient illumination Incandescent lamp: 3,000 lx max./ Sunlight: 10,000 lx max.
Ambient temperature range Operating: -25 to 55C/ Storage: -30 to 70C (with no icing or condensation)
Ambient humidity range Operating: 35 to 85%/ Storage: 35 to 95% (with no condensation)
Insulation resistance 20 M min. at 500 VDC
Dielectric strength 1,000 VAC at 50/60 Hz for 1 min. between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance Destruction: 500 m/s2 3 times each in X, Y and Z directions
Degree of protection IEC: IP67, IP68 *2., DIN 40050-9: IP69K *3. IEC: IP67, DIN 40050-9: IP69K *3
Weight
(packed
state/only
sensor)
Pre-wired cable (2M) 76 g Approx. 95 g/Approx. 65 g
Connector 22 g Approx. 50 g/Approx. 20 g
Material
Case SUS316L (1.4404)
Lens and Display PMMA
Adjuster –POM
Nut SUS316L (1.4404)
Accessories Instruction sheet
M18 nuts (2 pcs)
E3FC
6
Engineering Data (Reference Value)
Parallel Operating Range
Through-beam Models Retro-reflective Models (with MSR function)
E3FC-T@E3FC-R@
Operating Range
Diffuse-reflective Models
E3FC-D@2E3FC-D@3E3FC-D@5
BGS Models Transparent object detection models
E3FC-D@6E3FC-L@1, E3FC-L@2E3FC-B@1
Distance Y (mm)
Distance X (m)
405 1015202530350
-1000
-800
-600
-400
-200
200
0
400
600
800
1000
Y
X
Distance Y (mm)
Distance X (m)
200
-200 82460
150
50
-50
100
0
-100
-150
Reflector: E39-R1S
Y
X
30
-30600100 200 300 400 5000
10
-10
20
0
-20
Distance Y (mm)
Distance X (mm)
Sensing object: white paper
Y
X
Distance Y (mm)
Distance X (mm)
100
-100 1800200 400 600 800 1000 1200 1400 16000
80
20
-40
40
-20
60
0
-60
-80
Sensing object: 300 × 300 (mm) white paper
Y
X
Distance Y (mm)
Distance X (mm)
100
-100 700100 200 300 400 500 6000
80
20
-40
40
-20
60
0
-60
-80
Sensing object: white paper
Y
X
Distance Y (mm)
Distance X (mm)
100
−100 1600200 400 600 800 1000 1200 14000
80
20
−40
40
−20
60
0
−60
−80
Sensing object: 300 × 300 (mm) white paper
Y
X
Distance Z (mm)
Distance X (mm)
40
-40 25010050 150 2000
30
10
-10
20
0
-20
-30
E3FC-L@1
E3FC-L@2
Sensing object: white paper
Z
X
Distance Y (mm)
Distance X (mm)
40
−40 1200200 400 600 800 10000
30
10
−10
20
0
−20
−30
Reflector: E39-RP1
Y
X
7
E3FC
Excess Gain vs. Distance
Through-beam Models Retro-reflective Models (with MSR function)
E3FC-T@E3FC-R@
Diffuse-reflective Models
E3FC-D@2E3FC-D@3E3FC-D@5
Transparent object detection models
E3FC-D@6E3FC-B@1
Sensing Distance vs. Sensing Object Material
BGS Models
E3FC-L@1E3FC-L@2
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.1010203040506070
Excess gain ratio (multiple)
Distance (m)
Operating
level
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.102 46810
Excess gain ratio (multiple)
Distance (m)
Operating
level
Reflector: E39-R1S
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 200 400 600 800 1000
Excess gain ratio (multiple)
Distance (mm)
Operating
level
Sensing object: 100 × 100 (mm) white paper
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 0.5 1 1.5 2 2.5 3
Excess gain ratio (multiple)
Distance (m)
Operating
level
Sensing object: 300 × 300 (mm) white paper
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 200 400 600 800 1000
Excess gain ratio (multiple)
Distance (mm)
Operating
level
Sensing object: 300 × 300 (mm) white paper
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.10 0.5 1 1.5 2 2.5 3
Excess gain ratio (multiple)
Distance (m)
Operating
level
Sensing object: 300 × 300 (mm) white paper
100
70
50
30
10
7
5
3
1
0.7
0.5
0.3
0.101 234
Excess gain ratio (multiple)
Distance (m)
Operating
level
Reflector: E39-RP1
120
100
80
60
40
20
0
Material
Sensing distance (mm)
White paper SUSBlack paper
250
200
150
100
50
0
Material
Sensing distance (mm)
White paper SUSBlack paper
E3FC
8
Output circuit diagram
PNP Output
Model Operation
mode Timing charts Operation
selector Output circuit
E3FC-TP@
E3FC-RP@
E3FC-DP@
E3FC-BP@
Light-ON
Connect the
pink wire
(Pin(2)) to the
brown (Pin(1))
Dark-ON
Connect the
pink wire
(Pin(2)) to the
blue (Pin(3))
or open the
pink wire
(Pin(2))
E3FC-LP@
Light-ON
Connect the
pink wire
(Pin(2)) to the
brown (Pin(1))
Dark-ON
Connect the
pink wire
(Pin(2)) to the
blue (Pin(3))
or open the
pink wire
(Pin(2))
Light incident
Light interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
(Between blue
and black leads)
Output transistor
Load
(e.g., relay)
4
3
2
1
Pink
100 mA max.
(Control output)
Light-ON
Dark-ON
0 V
Operation
indicator
(Orange)
Stability
indicator
(Green)
Photo-
electric
Sensor
Main
Circuit
10 to 30 VDC
Brown
Black
Blue
Load
(Relay)
Through-beam Receivers, Retro-reflective Models,
Diffuse-reflective Models
Light incident
Light interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
(Between blue
and black leads)
Output transistor
Load
(e.g., relay)
3
1
Through-beam Emitter
Power
indicator
(green)
Photo-
electric
Sensor
Main
Circuit
Brown
Blue
10 to 30 VDC
NEAR FAR
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
Output transistor
Load
(e.g., relay)
(Between blue
and black leads)
4
3
2
1
Pink
100 mA max.
(Control output)
Light-ON
Dark-ON
0 V
Operation
indicator
(Orange)
Stability
indicator
(Green)
Photo-
electric
Sensor
Main
Circuit
10 to 30 VDC
Brown
Black
Blue
Load
(Relay)
Background suppression.
NEAR FAR
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(oramge)
Output transistor
Load
(e.g., relay)
(Between blue
and black leads)
9
E3FC
NPN Output
Connector Pin Arrangement
M12 Connector Pin Arrangement
Connectors (Sensor I/O connectors)
M12 4-wire Connectors
Model Operation
mode Timing charts Operation
selector Output circuit
E3FC-TN@
E3FC-RN@
E3FC-DN@
E3FC-BN@
Light-ON
Connect the
pink wire
(Pin(2)) to the
brown (Pin(1))
or open the
pink wire
(Pin(2))
Dark-ON
Connect the
pink wire
(Pin(2)) to the
blue (Pin(3))
E3FC-LN@
Light-ON
Connect the
pink wire
(Pin(2)) to the
brown (Pin(1))
or open the
pink wire
(Pin(2))
Dark-ON
Connect the
pink wire
(Pin(2)) to the
blue (Pin(3))
Light incident
Light interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
(Between brown
and black leads)
Output transistor
Load
(e.g., relay)
4
3
2
1
10 to 30 VDC
Brown
Black
Blue
Pink
100 mA max.
(Control output)
Light-ON
Dark-ON
Operation
indicator
(Orange)
Stability
indicator
(Green)
0 V
Load
(Relay)
Photo-
electric
Sensor
Main
Circuit
Through-beam Receivers, Retro-reflective Models,
Diffuse-reflective Models
Light incident
Light interrupted
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
(Between brown
and black leads)
Output transistor
Load
(e.g., relay)
NEAR FAR
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(orange)
Output transistor
Load
(e.g., relay)
(Between brown
and black leads)
Background suppression.
4
3
2
1
10 to 30 VDC
Brown
Black
Blue
Pink
100 mA max.
(Control output)
Light-ON
Dark-ON
Operation
indicator
(Orange)
Stability
indicator
(Green)
0 V
Load
(Relay)
Photo-
electric
Sensor
Main
Circuit
NEAR FAR
ON
OFF
ON
OFF
Operate
Reset
Operation indicator
(oramge)
Output transistor
Load
(e.g., relay)
(Between brown
and black leads)
3
1
24
Classification Wire color Connector pin No. Application
DC
Brown ➀Power supply (+V)
White ➁L/on · D/on selectable
Blue ➂Power supply (0 V)
Black ➃Output
2
4
13
1
2
3
4
Brown
Blue
White
Black
Pin No.
Wire color
E3FC
10
Safety Precautions
Refer to Warranty and Limitations of Liability.
This product is not designed or rated for directly or
indirectly ensuring safety of persons. Do not use it
for such a purpose.
Never use the product with an AC power supply.
Do not use the product with voltage in excess of the
rated voltage.
Do not use the product with incorrect wiring.
Otherwise, explosion, fire, malfunction may result.
Be sure to follow the safety precautions below for added safety.
1. Do not use the sensor under the environment with explosive,
flammable or corrosive gas.
2. Do not use the sensor under the oil or chemical environment
exceeding specifications. Performance is assured for typical
detergents and disinfectants used in Food & Beverage industry.
Refer to the following table when using these agents:
3. Do not use the sensor under the environment under the other
conditions in excess of rated.
4. Do not use the sensor in place that is exposed by direct sunlight.
5. Do not use the sensor in place where the sensor may receive
direct vibration or shock.
6. Do not use the thinner, alcohol, or other organic solvents.
7. Never disassemble, repair nor tamper with the sensor.
8. Please process it as industrial waste.
1. Laying Sensor wiring in the same conduit or duct as high-voltage
wires or power lines may result in malfunction or damage due to
conduit or use shielded cable.
2. Do not pull on the cable with excessive force.
3. If a commercial switching regulator is used, ground the FG (frame
ground) terminal.
4. The sensor will be available 100 ms after the power supply is tuned
ON. Start to use the sensor 100 ms or more after turning ON the
power supply. If the load and the sensor are connected to separate
power supplies, be sure to turn ON the sensor first.
5. Output pulses may be generated even when the power supply is
OFF. Therefore, it is recommended to first turn OFF the power
supply for the load or the load line.
6. The sensor must be mounted using the provided nuts. The proper
tightening torque is 20 N°m max..
WARNING
CAUTION
Precautions for Safe Use
Manufacturer Product name Concen-
tration Testtime
Diversey
Diverfoam SMS HD 5% 720 h
Oxofoam 5% 720 h
Acifoam 5% 720 h
Divosan Hypochlorit 1% 720 h
Divosan Forte 1% 720 h
Ecolab
P3-topactive® 200 5% 720 h
P3-topax® 56 5% 720 h
P3-topactive® OKTO 3% 720 h
P3-topax® 990 3% 720 h
P3-topax® 66 3% 720 h
General H2O26,5% 240 h
Precautions for Correct Use
11
E3FC
Dimensions
Sensors
(Unit: mm)
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
35.7
23
29.9
48
16.6
26.4
Operation indicator (orange)
Stability indicator (green)
M18×1
Sensitivity adjuster (Diffuse reflective, transparent models)
7
Receiver
Emitter
Optical axisOptical axis
(Through-beam,
transparent
models)
48
35.7
29.9
16.6
26.4
Operation indicator
(orange)
Stability indicator
(green)
M18×1
Vinyl insurated round cord 4 dia. 4 cores
(conductor cross sectional area: 0.128 mm²
(AWG26)/insulation outside diameter:
0.85 dia.)
standard length 2 m
Vinyl insurated round cord 4 dia. 4 cores
(conductor cross sectional area: 0.128 mm²
(AWG26)/insulation outside diameter:
0.85 dia.)
standard length 2 m
Pre-wired Models
E3FC-T@1@
E3FC-R@1@
E3FC-D@1@
E3FC-L@1@
E3FC-B@1@
23
29,9
37,5
48
16,6
26,4
M18x1
M12x1
Sensitivity adjuster (Diffuse reflective, transparent models)
Operation indicator (orange)
Stability indicator (green)
7
Receiver
Emitter
Optical axisOptical axis
(Through-beam,
transparent
models)
29,9
37,5
48
16,6
26,4
M18x1
M12x1
Operation indicator
(orange)
Stability indicator
(green)
12
34
M12 Connector Models
E3FC-T@2@
E3FC-R@2@
E3FC-D@2@
E3FC-L@2@
E3FC-B@2@
Terminal No. Specification
1+V
2 L/on · D/on selectable
30V
4 Output
Three, 24
24 dia.
M18 4 P=1
4
Attached nut
E3FC
12
Accessories (Order Separately)
34
40.3
5259.9
2.7
8
1.6
7.5
7
Two, 3.5 dia.
3.5
3.85
8±0.3
4.2 1
51.99
56
60
34
36.95
41
Reflectors
E39-R1S E39-R50
72 63.680
44
Two, 3.5 dia.
Reflector
3
8.5
0.2
43
37
R4
15
Ø 3.2
reflective surface
21.8 × 27.8 mm
5
30
E39-RP1 E39-R16
4.3
37
22
15
36.5
20
Two, 30°
Two, 4.3
Two, R 15
42
1.5
90°
(R16.5)
18.2 dia.
M18×1 4
Ø26
45°
Mounting brackets
E39-L183
Flush mounting nut
E39-EL16
In the interest of product improvement, specifications are subject to change without notice.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter-
est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for pub-
lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability
. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod-
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.
55.59.01.43.00
• 01-800-226-6766 • mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 01-800-226-6766 • mela@omron.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
Authorized Distributor:
E65I-E-02 12/14 Note: Specifications are subject to change. © 2014 Omron Electronics LLC Printed in U.S.A.
Printed on recycled paper.
Automation Control Systems
• Machine Automation Controllers (MAC) • Programmable Controllers (PLC)
• Operator interfaces (HMI) • Distributed I/O • Software
Drives & Motion Controls
• Servo & AC Drives • Motion Controllers & Encoders
Temperature & Process Controllers
• Single and Multi-loop Controllers
Sensors & Vision
• Proximity Sensors • Photoelectric Sensors • Fiber-Optic Sensors
• Amplified Photomicrosensors • Measurement Sensors
• Ultrasonic Sensors • Vision Sensors
Industrial Components
• RFID/Code Readers • Relays • Pushbuttons & Indicators
• Limit and Basic Switches • Timers • Counters • Metering Devices
• Power Supplies
Safety
• Laser Scanners • Safety Mats • Edges and Bumpers • Programmable Safety
Controllers • Light Curtains • Safety Relays • Safety Interlock Switches
OMRON AUTOMATION AND SAFETY • THE AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON EUROPE B.V. •
Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
•
+31 (0) 23 568 13 00
•
www.industrial.omron.eu