ADC124S101CIMMX - National Semiconductor

ADC124S101

ADC124S101 4 Channel, 500 ksps to 1 Msps, 12-Bit A/D Converter

Literature Number: SNAS283C

ADC124S101

February 19, 2010

4 Channel, 500 ksps to 1 Msps, 12-Bit A/D Converter

General Description

The ADC124S101 is a low-power, four-channel CMOS 12-bit

analog-to-digital converter with a high-speed serial interface.

Unlike the conventional practice of specifying performance at

a single sample rate only, the ADC124S101 is fully specified

over a sample rate range of 500 ksps to 1 Msps. The con-

verter is based on a successive-approximation register archi-

tecture with an internal track-and-hold circuit. It can be

configured to accept up to four input signals at inputs IN1

through IN4.

The output serial data is straight binary, and is compatible with

several standards, such as SPI™, QSPI™, MICROWIRE,

and many common DSP serial interfaces.

The ADC124S101 operates with a single supply that can

range from +2.7V to +5.25V. Normal power consumption us-

ing a +3V or +5V supply is 4.3 mW and 13.1 mW, respectively.

The power-down feature reduces the power consumption to

just 0.14 µW using a +3V supply, or 0.32 µW using a +5V

supply.

The ADC124S101 is packaged in a 10-lead MSOP package.

Operation over the industrial temperature range of −40°C to

+85°C is guaranteed.

Features

■Specified over a range of sample rates.

■Four input channels

■Variable power management

■Single power supply with 2.7V - 5.25V range

Key Specifications

■DNL +0.9/−0.6 LSB (typ)

■INL ± 0.64 LSB (typ)

■SNR 72.4 dB (typ)

■Power Consumption

■—3V Supply 4.3 mW (typ)

—5V Supply 13.1 mW (typ)

Applications

■Portable Systems

■Remote Data Acquisition

■Instrumentation and Control Systems

Pin-Compatible Alternatives by Resolution and Speed

All devices are fully pin and function compatible.

Resolution Specified for Sample Rate Range of:

50 to 200 ksps 200 to 500 ksps 500 ksps to 1 Msps

12-bit ADC124S021 ADC124S051 ADC124S101

10-bit ADC104S021 ADC104S051 ADC104S101

8-bit ADC084S021 ADC084S051 ADC084S101

Connection Diagram

20124905

TRI-STATE® is a trademark of National Semiconductor Corporation

QSPI™ and SPI™ are trademarks of Motorola, Inc.

ADC124S101 4 Channel, 500 ksps to 1 Msps, 12-Bit A/D Converter

Ordering Information

Order Code Temperature Range Description Top Mark

ADC124S101CIMM −40°C to +85°C 10-Lead MSOP Package X27C

ADC124S101CIMMX −40°C to +85°C 10-Lead MSOP Package, Tape & Reel X27C

ADC124S101EVAL Evaluation Board

Block Diagram

20124907

Pin Descriptions and Equivalent Circuits

Pin No. Symbol Description

ANALOG I/O

4-7 IN1 to IN4 Analog inputs. These signals can range from 0V to VA.

DIGITAL I/O

10 SCLK Digital clock input. This clock directly controls the conversion and readout processes.

9 DOUT Digital data output. The output samples are clocked out of this pin on falling edges of the

SCLK pin.

8 DIN Digital data input. The ADC124S101's Control Register is loaded through this pin on rising

edges of the SCLK pin.

1 CS Chip select. On the falling edge of CS, a conversion process begins. Conversions

continue as long as CS is held low.

POWER SUPPLY

2VA

Positive supply pin. This pin should be connected to a quiet +2.7V to +5.25V source and

bypassed to GND with a 1 µF capacitor and a 0.1 µF monolithic capacitor located within

1 cm of the power pin.

3 GND The ground return for the supply and signals.

www.national.com 2

ADC124S101

Absolute Maximum Ratings (Note 1, Note

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Supply Voltage VA−0.3V to 6.5V

Voltage on Any Pin to GND −0.3V to VA +0.3V

Input Current at Any Pin (Note 3) ±10 mA

Package Input Current(Note 3) ±20 mA

Power Consumption at TA = 25°C See (Note 4)

ESD Susceptibility (Note 5)

Human Body Model

Machine Model

2500V

250V

Junction Temperature +150°C

Storage Temperature −65°C to +150°C

Operating Ratings (Note 1, Note 2)

Operating Temperature Range −40°C ≤ TA ≤ +85°C

VA Supply Voltage +2.7V to +5.25V

Digital Input Pins Voltage Range −0.3V to VA

Clock Frequency 50 kHz to 16 MHz

Analog Input Voltage 0V to VA

Package Thermal Resistance

Package θJA

10-lead MSOP 190°C / W

Soldering process must comply with National

Semiconductor's Reflow Temperature Profile specifications.

Refer to www.national.com/packaging. (Note 6)

ADC124S101 Converter Electrical Characteristics (Note 9)

The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 8 to 16 MHz, fSAMPLE = 500 ksps to 1 Msps, CL = 35

pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.

Symbol Parameter Conditions Typical Limits

(Note 7)Units

STATIC CONVERTER CHARACTERISTICS

Resolution with No Missing Codes 12 Bits

INL Integral Non-Linearity +0.64 +1.6 LSB (max)

−0.64 −1.2 LSB (min)

DNL Differential Non-Linearity +0.9 +1.6 LSB (max)

−0.6 −1.0 LSB (min)

VOFF Offset Error 0.44 ±1.3 LSB (max)

OEM Channel to Channel Offset Error Match ±0.1 ±1.0 LSB (max)

FSE Full Scale Error −0.34 ±1.5 LSB (max)

FSEM Channel to Channel Full-Scale Error

Match ±0.1 ±1.0 LSB (max)

DYNAMIC CONVERTER CHARACTERISTICS

SINAD Signal-to-Noise Plus Distortion Ratio VA = +2.7V to 5.25V

fIN = 40.3 kHz, −0.02 dBFS 72 69.2 dB (min)

SNR Signal-to-Noise Ratio VA = +2.7V to 5.25V

fIN = 40.3 kHz, −0.02 dBFS 72.4 70.6 dB (min)

THD Total Harmonic Distortion VA = +2.7V to 5.25V

fIN = 40.3 kHz, −0.02 dBFS −82 −75 dB (max)

SFDR Spurious-Free Dynamic Range VA = +2.7V to 5.25V

fIN = 40.3 kHz, −0.02 dBFS 83 76 dB (min)

ENOB Effective Number of Bits VA = +2.7V to 5.25V 11.7 11.2 Bits (min)

Channel-to-Channel Crosstalk VA = +5.25V

fIN = 40.3 kHz −86 dB

IMD

Intermodulation Distortion, Second

Order Terms

VA = +5.25V

fa = 40.161 kHz, fb = 41.015 kHz −87 dB

Intermodulation Distortion, Third Order

Terms

VA = +5.25V

fa = 40.161 kHz, fb = 41.015 kHz −88 dB

FPBW -3 dB Full Power Bandwidth VA = +5V 11 MHz

VA = +3V 8 MHz

3 www.national.com

ADC124S101

Symbol Parameter Conditions Typical Limits

(Note 7)Units

ANALOG INPUT CHARACTERISTICS

VIN Input Range 0 to VAV

IDCL DC Leakage Current ±0.02 ±1 µA (max)

CINA Input Capacitance Track Mode 33 pF

Hold Mode 3 pF

DIGITAL INPUT CHARACTERISTICS

VIH Input High Voltage VA = +5.25V 2.4 V (min)

VA = +3.6V 2.1 V (min)

VIL Input Low Voltage 0.8 V (max)

IIN Input Current VIN = 0V or VA±0.1 ±10 µA (max)

CIND Digital Input Capacitance 2 4pF (max)

DIGITAL OUTPUT CHARACTERISTICS

VOH Output High Voltage ISOURCE = 200 µA VA − 0.03 VA − 0.5 V (min)

ISOURCE = 1 mA VA − 0.10

VOL Output Low Voltage ISINK = 200 µA 0.02 0.4 V (max)

ISINK = 1 mA 0.1

IOZH, IOZL TRI-STATE® Leakage Current ±1 µA (max)

COUT TRI-STATE® Output Capacitance 2 4pF (max)

Output Coding Straight (Natural) Binary

POWER SUPPLY CHARACTERISTICS (CL = 10 pF)

VASupply Voltage 2.7 V (min)

5.25 V (max)

Supply Current, Normal Mode

(Operational, CS low)

VA = +5.25V,

fSAMPLE = 1 Msps, fIN = 40 kHz 2.5 3.0 mA (max)

VA = +3.6V,

fSAMPLE = 1 Msps, fIN = 40 kHz 1.2 1.6 mA (max)

Supply Current, Shutdown (CS high)

VA = +5.25V,

fSAMPLE = 0 ksps 60 nA

VA = +3.6V,

fSAMPLE = 0 ksps 38 nA

Power Consumption, Normal Mode

(Operational, CS low)

VA = +5.25V 13.1 15.8 mW (max)

VA = +3.6V 4.3 5.8 mW (max)

Power Consumption, Shutdown (CS

high)

VA = +5.25V 0.32 µW

VA = +3.6V 0.14 µW

AC ELECTRICAL CHARACTERISTICS

fSCLK Maximum Clock Frequency (Note 8) 8MHz (min)

16 MHz (max)

fSSample Rate (Note 8) 500 ksps (min)

1Msps (max)

tCONV Conversion Time 13 SCLK cycles

DC SCLK Duty Cycle fSCLK = 16 MHz 50 30 % (min)

70 % (max)

tACQ Track/Hold Acquisition Time Full-Scale Step Input 3SCLK cycles

Throughput Time Acquisition Time + Conversion Time 16 SCLK cycles

www.national.com 4

ADC124S101

ADC124S101 Timing Specifications

The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 8 MHz to 16 MHz, fSAMPLE = 500 ksps to 1 Msps,

CL = 35 pF, Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.

Symbol Parameter Conditions Typical Limits

(Note 7)Units

tCSU Setup Time SCLK High to CS Falling Edge (Note 10)VA = +3.0V −3.5 10 ns (min)

VA = +5.0V −0.5

tCLH Hold time SCLK Low to CS Falling Edge (Note 10)VA = +3.0V +4.5 10 ns (min)

VA = +5.0V +1.5

tEN Delay from CS Until DOUT active VA = +3.0V +4 30 ns (max)

VA = +5.0V +2

tACC Data Access Time after SCLK Falling Edge VA = +3.0V +14.5 30 ns (max)

VA = +5.0V +13

tSU Data Setup Time Prior to SCLK Rising Edge +3 10 ns (min)

tHData Valid SCLK Hold Time +3 10 ns (min)

tCH SCLK High Pulse Width 0.5 x tSCLK 0.3 x tSCLK ns (min)

tCL SCLK Low Pulse Width 0.5 x tSCLK 0.3 x tSCLK ns (min)

tDIS CS Rising Edge to DOUT High-Impedance

Output Falling VA = +3.0V 1.8

20 ns (max)

VA = +5.0V 1.3

Output Rising VA = +3.0V 1.0

VA = +5.0V 1.0

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: All voltages are measured with respect to GND = 0V, unless otherwise specified.

Note 3: When the input voltage at any pin exceeds the power supply (that is, VIN < GND or VIN > VA), the current at that pin should be limited to 10 mA. The 20

mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. The Absolute

Maximum Rating specification does not apply to the VA pin. The current into the VA pin is limited by the Analog Supply Voltage specification.

Note 4: The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by TJmax, the

junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/θJA. The values

for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven

beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.

Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through zero ohms.

Note 6: Reflow temperature profiles are different for lead-free and non-lead-free packages.

Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level).

Note 8: This is the frequency range over which the electrical performance is guaranteed. The device is functional over a wider range which is specified under

Operating Ratings.

Note 9: Min/max specification limits are guaranteed by design, test, or statistical analysis.

Note 10: Clock may be either high or low when CS is asserted as long as setup and hold times tCSU and tCLH are strictly observed.

5 www.national.com

ADC124S101

Timing Diagrams

20124951

ADC124S101 Timing Diagram

20124908

Timing Test Circuit

20124906

ADC124S101 Serial Timing Diagram

20124950

SCLK and CS Timing Parameters

www.national.com 6

ADC124S101

Specification Definitions

ACQUISITION TIME is the time required to acquire the input

voltage. That is, it is time required for the hold capacitor to

charge up to the input voltage.

APERTURE DELAY is the time between the fourth falling

SCLK edge of a conversion and the time when the input signal

is acquired or held for conversion.

CONVERSION TIME is the time required, after the input volt-

age is acquired, for the ADC to convert the input voltage to a

digital word.

CROSSTALK is the coupling of energy from one channel into

the other channel, or the amount of signal energy from one

analog input that appears at the measured analog input.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of

the maximum deviation from the ideal step size of 1 LSB.

DUTY CYCLE is the ratio of the time that a repetitive digital

waveform is high to the total time of one period. The specifi-

cation here refers to the SCLK.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE

BITS) is another method of specifying Signal-to-Noise and

Distortion or SINAD. ENOB is defined as (SINAD − 1.76) /

6.02 and says that the converter is equivalent to a perfect

ADC of this (ENOB) number of bits.

FULL POWER BANDWIDTH is a measure of the frequency

at which the reconstructed output fundamental drops 3 dB

below its low frequency value for a full scale input.

FULL SCALE ERROR (FSE) is a measure of how far the last

code transition is from the ideal 1½ LSB below VREF+ and is

defined as:

VFSE = Vmax + 1.5 LSB – VREF+

where Vmax is the voltage at which the transition to the maxi-

mum code occurs. FSE can be expressed in Volts, LSB or

percent of full scale range.

GAIN ERROR is the deviation of the last code transition

(111...110) to (111...111) from the ideal (VREF − 1.5 LSB), af-

ter adjusting for offset error.

INTEGRAL NON-LINEARITY (INL) is a measure of the de-

viation of each individual code from a line drawn from negative

full scale (½ LSB below the first code transition) through pos-

itive full scale (½ LSB above the last code transition). The

deviation of any given code from this straight line is measured

from the center of that code value.

INTERMODULATION DISTORTION (IMD) is the creation of

additional spectral components as a result of two sinusoidal

frequencies being applied to the ADC input at the same time.

It is defined as the ratio of the power in the second and third

order intermodulation products to the power in one of the

original frequencies. IMD is usually expressed in dB.

MISSING CODES are those output codes that will never ap-

pear at the ADC outputs. These codes cannot be reached with

any input value. The ADC124S101 is guaranteed not to have

any missing codes.

OFFSET ERROR is the deviation of the first code transition

(000...000) to (000...001) from the ideal (i.e. GND + 0.5 LSB).

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in

dB, of the rms value of the input signal to the rms value of the

sum of all other spectral components below one-half the sam-

pling frequency, not including d.c. or the harmonics included

in THD.

SIGNAL TO NOISE PLUS DISTORTION (S/N+D or

SINAD) Is the ratio, expressed in dB, of the rms value of the

input signal to the rms value of all of the other spectral com-

ponents below half the clock frequency, including harmonics

but excluding d.c.

SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-

ence, expressed in dB, between the desired signal amplitude

to the amplitude of the peak spurious spectral component,

where a spurious spectral component is any signal present in

the output spectrum that is not present at the input and may

or may not be a harmonic.

TOTAL HARMONIC DISTORTION (THD) is the ratio, ex-

pressed in dB or dBc, of the rms total of the first five harmonic

components at the output to the rms level of the input signal

frequency as seen at the output. THD is calculated as

where Af1 is the RMS power of the input frequency at the out-

put and Af2 through Af6 are the RMS power in the first 5

harmonic frequencies.

THROUGHPUT TIME is the minimum time required between

the start of two successive conversion. It is the acquisition

time plus the conversion and read out times. In the case of

the ADC124S101, this is 16 SCLK periods.

7 www.national.com

ADC124S101

Typical Performance Characteristics TA = +25°C, fSAMPLE = 500 ksps to 1 Msps, fSCLK = 8 MHz to 16

MHz, fIN = 40.3 kHz unless otherwise stated.

DNL - VA = 3.0V

20124920

INL - VA = 3.0V

20124921

DNL - VA = 5.0V

20124962

INL - VA = 5.0V

20124963

DNL vs. Supply

20124922

INL vs. Supply

20124923

www.national.com 8

ADC124S101

DNL vs. Clock Frequency

20124924

INL vs. Clock Frequency

20124925

DNL vs. Clock Duty Cycle

20124926

INL vs. Clock Duty Cycle

20124927

DNL vs. Temperature

20124928

INL vs. Temperature

20124929

9 www.national.com

ADC124S101

SNR vs. Supply

20124930

THD vs. Supply

20124935

SNR vs. Clock Frequency

20124931

THD vs. Clock Frequency

20124936

SNR vs. Clock Duty Cycle

20124932

THD vs. Clock Duty Cycle

20124937

www.national.com 10

ADC124S101

SNR vs. Input Frequency

20124933

THD vs. Input Frequency

20124938

SNR vs. Temperature

20124934

THD vs. Temperature

20124939

SFDR vs. Supply

20124940

SINAD vs. Supply

20124945

11 www.national.com

ADC124S101

SFDR vs. Clock Frequency

20124941

SINAD vs. Clock Frequency

20124946

SFDR vs. Clock Duty Cycle

20124942

SINAD vs. Clock Duty Cycle

20124947

SFDR vs. Input Frequency

20124943

SINAD vs. Input Frequency

20124948

www.national.com 12

ADC124S101

SFDR vs. Temperature

20124944

SINAD vs. Temperature

20124949

ENOB vs. Supply

20124952

ENOB vs. Clock Frequency

20124953

ENOB vs. Clock Duty Cycle

20124954

ENOB vs. Input Frequency

20124955

13 www.national.com

ADC124S101

ENOB vs. Temperature

20124956

Spectral Response - 3V, 500 ksps

20124959

Spectral Response - 5V, 500 ksps

20124960

Spectral Response - 3V, 1.0 Msps

20124964

Spectral Response - 5V, 1.0 Msps

20124965

Power Consumption vs. Throughput

20124961

www.national.com 14

ADC124S101

Applications Information

1.0 ADC124S101 OPERATION

The ADC124S101 is a successive-approximation analog-to-

digital converter designed around a charge-redistribution dig-

ital-to-analog converter. Simplified schematics of the AD-

C124S101 in both track and hold modes are shown in

Figures 1, 2, respectively. In Figure 1, the ADC124S101 is in

track mode: switch SW1 connects the sampling capacitor to

one of four analog input channels through the multiplexer, and

SW2 balances the comparator inputs. The ADC124S101 is in

this state for the first three SCLK cycles after CS is brought

low.

Figure 2 shows the ADC124S101 in hold mode: switch SW1

connects the sampling capacitor to ground, maintaining the

sampled voltage, and switch SW2 unbalances the compara-

tor. The control logic then instructs the charge-redistribution

DAC to add fixed amounts of charge to the sampling capacitor

until the comparator is balanced. When the comparator is

balanced, the digital word supplied to the DAC is the digital

representation of the analog input voltage. The ADC124S101

is in this state for the fourth through sixteenth SCLK cycles

after CS is brought low.

The time when CS is low is considered a serial frame. Each

of these frames should contain an integer multiple of 16 SCLK

cycles, during which time a conversion is performed and

clocked out at the DOUT pin and data is clocked into the DIN

pin to indicate the multiplexer address for the next conversion.

20124909

FIGURE 1. ADC124S101 in Track Mode

20124910

FIGURE 2. ADC124S101 in Hold Mode

2.0 USING THE ADC124S101

A ADC124S101 timing diagram and a serial interface timing

diagram for the ADC124S101 are shown in the Timing Dia-

grams section. CS is chip select, which initiates conversions

and frames the serial data transfers. SCLK (serial clock) con-

trols both the conversion process and the timing of serial data.

DOUT is the serial data output pin, where a conversion result

is sent as a serial data stream, MSB first. Data to be written

to the ADC124S101's Control Register is placed on DIN, the

serial data input pin. New data is written to the ADC at DIN

with each conversion.

A serial frame is initiated on the falling edge of CS and ends

on the rising edge of CS. Each frame must contain an integer

multiple of 16 rising SCLK edges. The ADC output data

(DOUT) is in a high impedance state when CS is high and is

active when CS is low. Thus, CS acts as an output enable.

Additionally, the device goes into a power down state when

CS is high, and also between continuous conversion cycles.

During the first 3 cycles of SCLK, the ADC is in the track

mode, acquiring the input voltage. For the next 13 SCLK cy-

cles the conversion is accomplished and the data is clocked

out, MSB first, starting on the 5th clock. If there is more than

one conversion in a frame, the ADC will re-enter the track

mode on the falling edge of SCLK after the N*16th rising edge

of SCLK, and re-enter the hold/convert mode on the N*16+4th

falling edge of SCLK, where "N" is an integer.

When CS is brought high, SCLK is internally gated off. If SCLK

is stopped in the low state while CS is high, the subsequent

fall of CS will generate a falling edge of the internal version of

SCLK, putting the ADC into the track mode. This is seen by

the ADC as the first falling edge of SCLK. If SCLK is stopped

with SCLK high, the ADC enters the track mode on the first

falling edge of SCLK after the falling edge of CS.

15 www.national.com

ADC124S101

During each conversion, data is clocked into the DIN pin on

the first 8 rising edges of SCLK after the fall of CS. For each

conversion, it is necessary to clock in the data indicating the

input that is selected for the conversion after the current one.

See Tables 1, 2 and Table 3.

If CS and SCLK go low within the times defined by tCSU and

tCLH, the rising edge of SCLK that begins clocking data in at

DIN may be one clock cycle later than expected. It is, there-

fore, best to strictly observe the minimum tCSU and tCLH times

given in the Timing Specifications..

There are no power-up delays or dummy conversions re-

quired with the ADC124S101. The ADC is able to sample and

convert an input to full conversion immediately following pow-

er up. The first conversion result after power-up will be that of

IN1.

TABLE 1. Control Register Bits

Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

DONTC DONTC ADD2 ADD1 ADD0 DONTC DONTC DONTC

TABLE 2. Control Register Bit Descriptions

Bit #: Symbol: Description

7 - 6, 2 - 0 DONTC Don't care. The value of these bits do not affect device operation.

5 ADD2 These three bits determine which input channel will be sampled and converted

in the next track/hold cycle. The mapping between codes and channels is shown

in Table 3.

4 ADD1

3 ADD0

TABLE 3. Input Channel Selection

ADD2 ADD1 ADD0 Input Channel

x 0 0 IN1 (Default)

x 0 1 IN2

x 1 0 IN3

x 1 1 IN4

3.0 ADC124S101 TRANSFER FUNCTION

The output format of the ADC124S101 is straight binary.

Code transitions occur midway between successive integer

LSB values. The LSB width for the ADC124S101 is VA/4096.

The ideal transfer characteristic is shown in Figure 3. The

transition from an output code of 0000 0000 0000 to a code

of 0000 0000 0001 is at 1/2 LSB, or a voltage of VA/8192.

Other code transitions occur at steps of one LSB.

20124911

FIGURE 3. Ideal Transfer Characteristic

www.national.com 16

ADC124S101

4.0 TYPICAL APPLICATION CIRCUIT

A typical application of the ADC124S101 is shown in Figure

4. Power is provided in this example by the National Semi-

conductor LP2950 low-dropout voltage regulator, available in

a variety of fixed and adjustable output voltages. The power

supply pin is bypassed with a capacitor network located close

to the ADC124S101.

Because the reference for the ADC124S101 is the supply

voltage, any noise on the supply will degrade device noise

performance. To keep noise off the supply, use a dedicated

linear regulator for this device, or provide sufficient decou-

pling from other circuitry to keep noise off the ADC124S101

supply pin. Because of the ADC124S101's low power re-

quirements, it is also possible to use a precision reference as

a power supply to maximize performance. The four-wire in-

terface is also shown connected to a microprocessor or DSP.

20124913

FIGURE 4. Typical Application Circuit

5.0 ANALOG INPUTS

An equivalent circuit for one of the ADC124S101's input chan-

nels is shown in Figure 5. Diodes D1 and D2 provide ESD

protection for the analog inputs. At no time should any input

go beyond (VA + 300 mV) or (GND − 300 mV), as these ESD

diodes will begin conducting, which could result in erratic op-

eration. For this reason, these ESD diodes should NOT be

used to clamp the input signal.

The capacitor C1 in Figure 5 has a typical value of 3 pF, and

is mainly the package pin capacitance. Resistor R1 is the on

resistance of the multiplexer and track / hold switch, and is

typically 500 ohms. Capacitor C2 is the ADC124S101 sam-

pling capacitor, and is typically 30 pF. The ADC124S101 will

deliver best performance when driven by a low-impedance

source to eliminate distortion caused by the charging of the

sampling capacitance. This is especially important when us-

ing the ADC124S101 to sample AC signals. Also important

when sampling dynamic signals is a band-pass or low-pass

filter to reduce harmonics and noise, improving dynamic per-

formance.

20124914

FIGURE 5. Equivalent Input Circuit

6.0 DIGITAL INPUTS AND OUTPUTS

The ADC124S101's digital output DOUT is limited by, and

cannot exceed, the supply voltage, VA. The digital input pins

are not prone to latch-up and, and although not recommend-

ed, SCLK, CS and DIN may be asserted before VA without

any latch-up risk.

7.0 POWER SUPPLY CONSIDERATIONS

The ADC124S101 is fully powered-up whenever CS is low,

and fully powered-down whenever CS is high, with one ex-

ception: the ADC124S101 automatically enters power-down

mode between the 16th falling edge of a conversion and the

1st falling edge of the subsequent conversion (see Timing

Diagrams).

The ADC124S101 can perform multiple conversions back to

back; each conversion requires 16 SCLK cycles. The AD-

C124S101 will perform conversions continuously as long as

CS is held low.

The user may trade off throughput for power consumption by

simply performing fewer conversions per unit time. The Power

Consumption vs. Sample Rate curve in the Typical Perfor-

mance Curves section shows the typical power consumption

of the ADC124S101 versus throughput. To calculate the pow-

er consumption, simply multiply the fraction of time spent in

the normal mode by the normal mode power consumption,

and add the fraction of time spent in shutdown mode multi-

plied by the shutdown mode power dissipation.

7.1 Power Management

When the ADC124S101 is operated continuously in normal

mode, the maximum throughput is fSCLK/16. Throughput may

be traded for power consumption by running fSCLK at its max-

imum 16 MHz and performing fewer conversions per unit

time, putting the ADC124S101 into shutdown mode between

conversions. A plot of typical power consumption versus

17 www.national.com

ADC124S101

throughput is shown in the Typical Performance Curves sec-

tion. To calculate the power consumption for a given through-

put, multiply the fraction of time spent in the normal mode by

the normal mode power consumption and add the fraction of

time spent in shutdown mode multiplied by the shutdown

mode power consumption. Generally, the user will put the part

into normal mode and then put the part back into shutdown

mode. Note that the curve of power consumption vs. through-

put is nearly linear. This is because the power consumption

in the shutdown mode is so small that it can be ignored for all

practical purposes.

7.2 Power Supply Noise Considerations

The charging of any output load capacitance requires current

from the power supply, VA. The current pulses required from

the supply to charge the output capacitance will cause voltage

variations on the supply. If these variations are large enough,

they could degrade SNR and SINAD performance of the ADC.

Furthermore, discharging the output capacitance when the

digital output goes from a logic high to a logic low will dump

current into the die substrate, which is resistive. Load dis-

charge currents will cause "ground bounce" noise in the sub-

strate that will degrade noise performance if that current is

large enough. The larger is the output capacitance, the more

current flows through the die substrate and the greater is the

noise coupled into the analog channel, degrading noise per-

formance.

To keep noise out of the power supply, keep the output load

capacitance as small as practical. If the load capacitance is

greater than 35 pF, use a 100 Ω series resistor at the ADC

output, located as close to the ADC output pin as practical.

This will limit the charge and discharge current of the output

capacitance and improve noise performance.

www.national.com 18

ADC124S101

Physical Dimensions inches (millimeters) unless otherwise noted

10-Lead MSOP

Order Number ADC124S101CIMM, ADC124S101CIMMX

NS Package Number P0MUB10A

19 www.national.com

ADC124S101

Notes

ADC124S101 4 Channel, 500 ksps to 1 Msps, 12-Bit A/D Converter

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

www.national.com

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench

Audio www.national.com/audio App Notes www.national.com/appnotes

Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns

Data Converters www.national.com/adc Samples www.national.com/samples

Interface www.national.com/interface Eval Boards www.national.com/evalboards

LVDS www.national.com/lvds Packaging www.national.com/packaging

Power Management www.national.com/power Green Compliance www.national.com/quality/green

Switching Regulators www.national.com/switchers Distributors www.national.com/contacts

LDOs www.national.com/ldo Quality and Reliability www.national.com/quality

LED Lighting www.national.com/led Feedback/Support www.national.com/feedback

Voltage References www.national.com/vref Design Made Easy www.national.com/easy

PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions

Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero

Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic

PLL/VCO www.national.com/wireless PowerWise® Design

University

www.national.com/training

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email: support@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265