MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 Features The MAPS-010145 is ideally suited for use where high phase accuracy with minimum loss variation over the phase shift range are required. The 4 mm PQFN package provides a smaller footprint than is typically available for a digital phase shifter with an internal driver. Typical applications include communications antennas and phased array radars. D6 D5 D4 D3 or LE VCC (+5 V) 24 0.1 F 23 22 21 20 19 1 4 RFIN 5 GND 6 See Detail 7 8 9 10 11 12 GND GND 6-Bit Phase Shifter GND 3 GND 2 0.1 F 18 GND P/S GND Description The MAPS-010145 is a GaAs pHEMT 4-bit digital phase shifter with an integrated CMOS driver in a 4 mm PQFN plastic surface mount package. Step size is 22.5 providing phase shift from 0 to 360 in 22.5 steps. This design has been optimized to minimize variation in attenuation over the phase shift range. D2 or CLK D1 or SERIN VEE (-5 V) GND 4 Bit Digital Phase Shifter 360 Coverage with LSB = 22.5 Integrated CMOS Driver Serial or Parallel Control Low DC Power Consumption Minimal Attenuation Variation over Phase Shift Range 50 Impedance EAR99 Lead-Free 4 mm 24-Lead PQFN Package RoHS* Compliant GND Functional Schematic 17 SEROUT 16 GND 15 GND 14 RFOUT 13 GND Phase Shifter Detail RFIN RFOUT -22.5 deg. -45 deg. -90 deg. -180 deg. Pin Configuration2 Pin No. Function Pin No. Function 1 VEE 13 GND 2 P/S 14 RFOUT 3 GND 15 GND 4 GND 16 GND 5 RFIN 17 SEROUT 6 GND 18 VCC 1 Ordering Information Part Number Package 7 GND 19 D6 MAPS-010145-TR0500 500 piece reel 8 GND 20 D5 MAPS-010145-001SMB Sample Test Board 9 GND 21 D4 10 GND 22 D3 or LE 11 GND 23 D2 or CLK 12 GND 24 D1 or SERIN 1. Reference Application Note M513 for reel size information. 2. The exposed pad centered on the package bottom must be connected to RF, DC and thermal ground. * Restrictions on Hazardous Substances, European Union Directive 2011/65/EU. 1 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151 MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 Electrical Specifications: Freq. = 3.5 - 6.0 GHz, TA = 25C, Z0 = 50 , VCC = +5.0 V, VEE = -5.0 V Parameter Test Conditions Units Min. Typ. Max. Operating Power 3 3.5 - 6.0 GHz dBm -- -- +25 Insertion Loss (Any Phase State) Any Phase State dB -- 5.0 6.5 Attenuation Variation Across All Phase States dB -- 1 -- RMS Attenuation Error 4 All Values Relative to Insertion Loss at Reference Phase dB -- 0.4 -- RMS Phase Error 4 All Values Relative to Reference Phase deg -- 3 -- -- Phase Accuracy Relative to Reference Loss State 22.5 Degree Bit 45 Degree Bit 90 Degree Bit 180 Degree Bit Sum of All Bits deg -- 1.7 1.0 2.0 3.5 2.5 VSWR RF Input RF Output Ratio -- 1.8:1 1.8:1 -- 1 dB Compression Reference State dBm -- 27 -- Input IP3 Two-tone inputs up to +5 dBm dBm -- 45 -- TRISE, TFALL 10% to 90% RF, 90% to 10% RF ns -- 50 -- V 3.0 -5.5 -- -5.0 5.5 -3.0 5 VCC VEE -- -- VIL VIH LOW-level input voltage HIGH-level input voltage V 0.0 0.7 x VCC -- 0.3 x VCC VCC lIN (Input Control Current) VIN = VCC or GND A -- 1 -- VOH VOL For serial out; IOH = -100 A For serial out; IOL = 100 A V VCC - 0.2 -- -- -- 0.2 ICC (Quiescent Supply Current) VCONTROL = VCC or GND A -- -- 2 IEE VEE min to max VIN = VIL or VIH mA -1.0 -0.1 -- 3. Maximum operating power is the maximum power where the specifications are guaranteed. 4. RMS is calculated across all 15 amplitude or phase states relative to the amplitude or phase in the 0 phase state at a given frequency. 5. This phase shifter is guaranteed to have monotonic phase shift. 2 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151 MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 Typical Performance Curves RFIN Return Loss vs. Frequency (All States) RFOUT Return Loss vs. Frequency (All States) 0 0 -5 -5 -10 -10 -15 -15 -20 -20 -25 -25 -30 -30 -35 3.5 4.0 4.5 5.0 5.5 6.0 -35 3.5 4.0 4.5 Mean RMS Phase Error vs. Frequency 1.5 8 1.2 6 0.9 4 0.6 2 0.3 3.5 4.0 4.5 5.0 5.5 6.0 0 3.5 4.0 4.5 Frequency (GHz) 6.0 5.0 5.5 6.0 Frequency (GHz) Phase Error (degrees) vs. State Amplitude Error (dB) vs. State 15 2.0 3.5 GHz 4.0 GHz 4.5 GHz 5.0 GHz 5.5 GHz 6.0 GHz 1.5 10 1.0 5 0.5 0 0.0 -0.5 -5 3.5 GHz 4.0 GHz 4.5 GHz 5.0 GHz 5.5 GHz 6.0 GHz -10 -15 5.5 Mean RMS Amplitude Error vs. Frequency 10 0 5.0 Frequency (GHz) Frequency (GHz) 0 45 90 -1.0 -1.5 135 180 225 State (deg) 270 315 360 -2.0 0 45 90 135 180 225 270 315 360 State 3 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151 MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 Typical Performance Curves Amplitude Variation vs. Phase State Phase Shift vs. Frequency (Major States) 0 0 -45 -2 -90 -135 -4 -180 -225 -6 -270 -315 -8 -360 -10 -405 3.5 4.0 4.5 5.0 5.5 6.0 3.5 4.0 22.5 45 67.5 Absolute Maximum Ratings6,7 Parameter Absolute Maximum Input Power 3.5 - 6.0 GHz +27 dBm VCC -0.5 V VCC +7.0 V VEE -7.0 V VEE +0.5 V D1-D4, P/S, LE, CLK or SER IN -0.5 V VIN VCC + 0.5 V SER OUT -0.5 V VOUT VCC + 0.5 V Operating Temperature -40C to +85C Storage Temperature -65C to +150C 4.5 5.0 5.5 6.0 Frequency (GHz) Frequency (GHz) 90 112.5 135 157.5 180 205.5 225 247.5 270 292.5 315 337.5 Sample Board Header Pin Labels 6. Exceeding any one or combination of these limits may cause permanent damage to this device. 7. MACOM does not recommend sustained operation near these survivability limits. Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity Gallium Arsenide and Silicon Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. 4 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151 MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 Modes of Operation: Serial and Direct Parallel Mode Truth Table8,9 Serial Mode The serial control interface (SERIN, CLK, LE, SEROUT) is compatible with the SPI protocol. SPI mode is activated when P/S is kept high. The 6-bit serial word must be loaded with the MSB first. After shifting in the 6 bit word, a rising edge on LE will set the phase shifter to the desired state. While LE is high the CLK is masked to protect the data while implementing the change. SEROUT is SERIN delayed by 6 clock cycles. When P/S is low, the serial control interface is disabled. When P/S is set high, Pins 22, 23, and 24 have the LE, CLK, and SER IN function. P/S LE Mode 1 X Serial 0 N/A Direct Parallel 8. There are two dummy bits (D1 & D2), that must be sent in the serial mode. This is because the 4 bit phase shifter uses the same driver as the 6 bit phase shifter. 9. In the parallel mode, D1 and D2 should be tied to ground or to VCC. Truth Table (Digital Phase Shifter)10 D6 D5 D4 D3 D2 D1 Phase Shift 0 0 0 0 X X Reference Phase 0 0 0 1 X X 22.5 0 0 1 0 X X 45 0 1 0 0 X X 90 Direct Parallel Mode 1 0 0 0 X X 180 The parallel mode is enabled when P/S is set low. In the direct parallel mode, the phase shifter is controlled by the parallel control inputs directly. When P/S is set low, Pins 22, 23, and 24 have the D3, D2, and D1 function. 1 1 1 1 X X 337.5 In serial mode operation, the outputs will stay constant while LE is kept low. 10. 0 = CMOS Low; 1 = CMOS High, X is CMOS Low or High Serial Interface Timing Characteristics Symbol Parameter tSCK Typical Performance Units -40C 25C +85C Min. Serial Clock Period 100 100 100 ns tCS Min. Control Set-up Time 20 20 20 ns tCH Min. Control Hold Time 20 20 20 ns tLS Min. LE Set-up Time 10 10 10 ns tLEW Min. LE Pulse Width 10 10 10 ns tLH Min. Serial Clock Hold Time from LE 10 10 10 ns tLES Min. LE Pulse Spacing 630 630 630 ns 5 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151 MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 Functionality Modes of Operation: Serial and Direct Parallel Serial Input Interface Timing Diagram tLS tLEW tLH SERIAL CLK LE tLES CONTROL WORD D5 MSB D4 tCS D1 D0 LSB tCH Lead Free 4 mm 24-Lead PQFN Reference Application Note S2083 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 1 requirements. Plating is 100% matte tin over copper. 6 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151 MAPS-010145 Digital Phase Shifter 4-Bit, 3.5 - 6.0 GHz Rev. V3 MACOM Technology Solutions Inc. All rights reserved. Information in this document is provided in connection with MACOM Technology Solutions Inc ("MACOM") products. These materials are provided by MACOM as a service to its customers and may be used for informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM assumes no responsibility for errors or omissions in these materials. MACOM may make changes to specifications and product descriptions at any time, without notice. MACOM makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this document. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM customers using or selling MACOM products for use in such applications do so at their own risk and agree to fully indemnify MACOM for any damages resulting from such improper use or sale. 7 MACOM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support DC-0007151