DATA SHEET THIN FILM CHIP RESISTORS General purpose RJ series (Pb Free) 1%, TC50 Product specification - May 30, 2005 V.1 sizes 0201/0402/0603/0805/ 1206/1210/2010/2512 Product specification Chip Resistor Surface Mount RJ 2 10 0201 to 2512 (Pb Free) SERIES SCOPE This specification describes RJ0201 to RJ2512 general purpose chip resistors with lead-free terminations made by thin film process. ORDERING INFORMATION Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. PHYCOMP ORDERING CODE 12NC CODE 2390 XXX XXXXX L (1) (2) (3) (4) RJ START TOL. RESISTANCE SIZE IN (1) (%) RANGE EMBOSSED TAPE ON REEL(2) PAPER/PE TAPE ON REEL (units) (2) 4,000 5,000 10,000 20,000 0201 2390 1% 10 to 30 k - - 409 8xxxx 429 8xxxx 449 8xxxx 0402 2390 1% 10 to 121 k - - 407 8xxxx 427 8xxxx 447 8xxxx 0603 2390 1% 3 to 681 k - 404 8xxxx 424 8xxxx 444 8xxxx - 0805 2390 1% 3 to 1.5 M - 401 8xxxx 421 8xxxx 441 8xxxx - 1206 2390 1% 3 to 1.5 M - 411 8xxxx 431 8xxxx 451 8xxxx - 1210 2390 1% 1 to 1 M - 412 0xxxx 432 8xxxx 412 8xxxx - 2010 2390 1% 10 to 1 M 415 8xxxx - - - - 2512 2390 1% 10 to 1 M 418 8xxxx - - - - (1) The resistors have a 12-digit ordering code starting with 2390. (2) The subsequent 4 digits indicate the resistor tolerance and packaging. (3) The remaining 4 digits represent the resistance value with the last digit indicating the multiplier as shown in the table of "Last digit of 12NC". (4) "L" means lead-free terminations (a) . ORDERING EXAMPLE The ordering code of a RJ0603 resistor, TC50 value 56 X, with 1% tolerance, supplied in tape of 5,000 units per reel is: 239040485609L. Last digit of 12NC Resistance decade (3) NOTE Last digit 0.01 to 0.0976 X 0.1 to 0.976 X 0 1 to 9.76 X 8 10 to 97.6 X 9 100 to 976 X 1 1 to 9.76 kX 2 10 to 97.6 kX 3 100 to 976 kX 4 1 to 9.76 MX 5 10 to 97.6 MX 6 Example: 50,000 7 0.02 X = 0200 or 200 0.3 X = 3007 or 307 1X = 1008 or 108 33 kX = 3303 or 333 10 MX = 1006 or 106 a. The "L" at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp "LFP"= lead free production. b. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet. c. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006) www.yageo.com May 30, 2005 V.1 3 Product specification Chip Resistor Surface Mount CTC RJ SERIES 10 0201 to 2512 (Pb Free) CODE RJ XXXX F X X XX XXXX L (1) (2) (3) (4) (5) (6) (7) (1) SIZE 0201 ORDERING EXAMPLE The ordering code of a RJ0603 chip resistor, TC50 value 56 X with 1% tolerance, supplied in 7-inch tape reel is: RJ0603FRE0756RL. 0402 NOTE 0603 a. The "L" at the end of the code is only for ordering. On the reel label, the standard CTC will be mentioned an additional stamp "LFP"= lead free production. 0805 1206 1210 2010 2512 b. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet. c. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006) (2) TOLERANCE F = 1% (3) PACKAGING TYPE R = Paper/PE taping reel K = Embossed taping reel (4) TEMPERATURE COEFFICIENT OF RESISTANCE E = 50 ppm/C (5) TAPING REEL 07 = 7 inch dia. Reel 10 = 10 inch dia. Reel (not preferred) 13 = 13 inch dia. Reel (6) RESISTANCE VALUE 5R6, 56R, 560R, 5K6, 56K, 1M. (7) RESISTOR TERMINATIONS L = Lead free terminations (matte tin) (a) www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount RJ SERIES 4 10 0201 to 2512 (Pb Free) MARKING RJ0805 / RJ1206 / RJ1210 / RJ2010 / RJ2512 Either resistance in E-24 or E-96: 4 digits 00 YNSC004 Fig. 1 Value = 10 k First three digits for significant figure and 4th digit for number of zeros RJ0603 E-24 series: 3 digits ynsc015 Fig. 2 Value = 12 k 10C ynsc002 First two digits for significant figure and 3rd digit for number of zeros E-96 series: 3 digits for 06031% EIA-96 marking method Fig. 3 Value = 12.4 k RJ0201 / RJ0402 ynsc007 No marking Fig. 4 For marking codes, please see EIA-marking code rules in data sheet "Chip resistors marking". www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount RJ 5 10 0201 to 2512 (Pb Free) SERIES CONSTRUCTION The resistors are constructed out of a high-grade ceramic body. Internal metal electrodes are added at each end and connected by a resistive layer. The resistive layer is adjusted to give the approximate required resistance and laser cutting of this resistive layer that achieves tolerance trims the value. The resistive layer is covered with a protective coat and printed with the resistance value. Finally, the two external terminations (matte tin) are added. See fig. 5. OUTLINES For dimension see Table 1 protective coat resistive layer inner electrode H end termination ceramic substrate I2 protective coat DIMENSION I1 Table 1 For outlines see fig. 5 TYPE RJ0201 L (mm) W (mm) H (mm) I1 (mm) I2 (mm) 0.6 0.10 0.30 0.05 0.25 0.05 0.15 0.10 0.15 0.10 W RJ0402 1.00 0.10 0.50 0.05 0.30 0.05 0.20 0.10 0.25 0.10 RJ0603 1.60 0.10 0.80 0.10 0.45 0.10 0.25 0.15 0.25 0.15 YNSC056 L RJ0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 RJ1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 RJ1210 3.10 0.10 2.60 0.15 0.55 0.10 0.50 0.20 0.50 0.20 Fig. 5 Chip resistor outlines RJ2010 5.00 0.10 2.50 0.15 0.55 0.10 0.60 0.20 0.50 0.20 RJ2512 6.35 0.10 3.20 0.15 0.55 0.10 0.60 0.20 0.50 0.20 ELECTRICAL CHARACTERISTICS Table 2 RESISTANCE RANGE OPERATING TEMPERATURE RANGE DERATED TO 0 LOAD AT MAXIMUM WORKING VOLTAGE DIELECTRIC WITHSTAND VOLTAGE MAXIMUM OVERTOAD VOLTAGE TEMPERATURE COEFFICIENT OF RESISTANCE RJ0201 10 to 22 K -55 C to +125 C +125 C 15 V 50 V 50 V 50 ppm/C RJ0402 1 to 121 K -55 C to +125 C +125 C 25 V 100 V 100 V 50 ppm/C RJ0603 1 to 681 K -55 C to +125 C +125 C 50 V 100 V 100 V 50 ppm/C RJ0805 1 to 1.5 M -55 C to +125 C +125 C 100 V 250 V 200 V 50 ppm/C RJ1206 1 to 1.5 M -55 C to +125 C +125 C 150 V 250 V 250 V 50 ppm/C RJ1210 1 to 1 M -55 C to +125 C +125 C 150 V 400 V 300 V 50 ppm/C RJ2010 1 to 1 M -55 C to +125 C +125 C 150 V 400 V 300 V 50 ppm/C RJ2512 1 to 1 M -55 C to +125 C +125 C 150 V 400 V 300 V 50 ppm/C TYPE www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount RJ SERIES 6 10 0201 to 2512 (Pb Free) FOOTPRINT AND SOLDERING PROFILES ENVIRONMENTAL DATA For recommended footprint and soldering profiles, please see the special data sheet "Chip resistors mounting". For material declaration information (IMDS-data) of the products, please see the separated info "Environmental data" conformed to EU RoHS. PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PACKING STYLE REEL DIMENSION RJ0201 RJ0402 RJ0603 RJ0805 RJ1206 RJ1210 RJ2010 RJ2512 7" (178 mm) 10,000 10,000 5,000 5,000 5,000 5,000 --- --- mm) (2) 20,000 20,000 10,000 10,000 10,000 10,000 --- --- 13" (330 mm) 50,000 50,000 20,000 20,000 20,000 20,000 --- --- 7" (178 mm) --- --- --- --- --- --- 4,000 4,000 Paper/PE taping reel (R) 10" (254 Embossed taping reel (K) NOTE 1. For Paper/PE/Embossed tape and reel specification/dimensions, please see the special data sheet "Packing" document. 2. 10" reel is not preferred typing reel. FUNCTIONAL DESCRIPTION OPERATINGTEMPERATURE RANGE Range: -55C to +125C handbook, P halfpage POWER RATING Each type rated power at 70C: RJ0201=1/20 W, RJ0402=1/16 W, RJ0603=1/16 W, RJ0805=1/10 W, RJ1206=1/8 W, RJ1210=1/4 W, RJ2010=1/2 W, RJ2512=3/4 W. 50 RATED VOLTAGE The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V = (P X R) MLB206 max (%Prated ) 100 0 55 0 50 70 100 125 o Tamb ( C) Fig. 6 Maximum dissipation (Pmax) in percentage of rated power as a function of the operating ambient temperature (Tamb ) Where V = Continuous rated DC or AC (rms) working voltage (V) P = Rated power (W) R = Resistance value (X) www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount RJ SERIES 7 10 0201 to 2512 (Pb Free) TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements TEST Temperature Coefficient of Resistance (T.C.R.) TEST METHOD PROCEDURE REQUIREMENTS MIL-STD-202F-method 304; At +25/-55 C and +25/+125 C 50 ppm/C JIS C 5202-4.8 Formula: R2-R1 T.C.R= ------------------------- x106 (ppm/C) R1(t2-t1) Where t1=+25 C or specified room temperature t2=-55 C or +125 C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms MIL-STD-202F-method 107G; At -65 (+0/-10) C for 2 minutes and at +125 (+10/-0) C for 2 minutes; 25 cycles (0.5%+0.05 ) At -65 (+0/-5) C for 1 hour; RCWV applied for 45 (+5/-0) minutes (0.5%+0.05 ) (1.0%+0.05 ) IEC 60115-1 4.13 2.5 x RCWV applied for 5 seconds at room temperature Insulation Resistance MIL-STD-202F-method 302; RCOV for 1 minute 10 G IEC 60115-1 4.6.1.1 Details see below table 5 Dielectric Withstand Voltage MIL-STD-202F-method 301; Maximum voltage (Vrms) applied for 1 minute IEC 60115-1 4.6.1.1 Details see below table 5 Resistance to Soldering Heat MIL-STD-202F-method 210C; Unmounted chips; 260 5 C for 10 1 seconds (0.5%+0.05 ) Life MIL-STD-202F-method 108A; At 702 C for 1,000 hours; RCWV applied for 1.5 hours on and 0.5 hour off (1%+0.05 ) Thermal Shock IEC 60115-1 4.19 Low Temperature Operation MIL-R-55342D-Para 4.7.4 Short Time Overload MIL-R-55342D-Para 4.7.5; IEC 60115-1 4.18 IEC 60115-1 4.25.1 No visible damage No visible damage No breakdown or flashover No visible damage www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount RJ 8 10 0201 to 2512 (Pb Free) SERIES Table 4 Test condition, procedure and requirements (continued) TEST Solderability Bending Strength TEST METHOD PROCEDURE REQUIREMENTS MIL-STD-202F-method 208A; Solder bath at 2453 C Well tinned (95% covered) IEC 60115-1 4.17 Dipping time: 20.5 seconds No visible damage Resistors mounted on a 90 mm glass epoxy resin PCB (FR4) (1.0%+0.05 ) JIS C 5202.6.14; IEC 60115-1 4.15 No visible damage Bending: see table 6 for each size Resistance to Solvent Noise MIL-STD-202F-method 215; No smeared IEC 60115-1 4.29 lsopropylalcohol (C3H7OH) or dichloromethane (CH2Cl2) followed by brushing JIS C 5202 5.9; Maximum voltage (Vrms) applied. < 10 dB JIS C 5202 7.5; 1,000 hours; 402 C; 93(+2/-3)% RH IEC 60115-8 4.24.8 (0.5%+0.05 ) RCWV applied for 1.5 hours on and 0.5 hour off EIA/IS 4.13B; Solder bath at 2605 C IEC 60115-8 4.18 Dipping time: 301 seconds JIS C 5202 5.8 At room temperature; 2.5 x RCWV applied for 1 second on and 25 seconds off; total 10,000 cycles On request On request MIL-STD-202F-method 106F; 42 cycles; total 1,000 hours (0.5%+0.05) IEC 60115-1 4.24.2 Shown as figure 7 No visible damage IEC 60115-1 4.12 Humidity (steady state) Leaching Intermittent Overload Resistance to Vibration Moisture Resistance Heat No visible damage (1.0%+0.05 ) Table 5 Criteria of rated continued working voltage and overload voltage TYPE RJ0201 RJ0402 RJ0603 RJ0805 RJ1206 RJ1210 RJ2010 RJ2512 50 100 100 300 500 500 500 500 Voltage (DC/unit: V); (AC/ unit: Vrms) Table 6 Bending for sizes 0201 to 2512 TYPE Specification (mm) RJ0201 RJ0402 RJ0603 RJ0805 RJ1206 RJ1210 RJ2010 RJ2512 2 2 3 3 2 2 2 2 www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount 75 RJ 80 - 98% RH 90 - 98% RH temperature [C] 90 - 98% RH 80 - 98% RH 9 10 0201 to 2512 (Pb Free) SERIES 90 - 98% RH initial drying 24 hours rate of change of temperature is unspecified, however, specimens shall not be subjected to radiant heating from chamber conditioning processes 50 end of final cycle; measurements as specified in 2.7 +10 C (+18 F) -2 C (-3.6 F) 25 initial measurements as specified in 2.2 0 temperature tolerance 2 C (3.6 F) unless otherwise specified voltage applied as specified in 2.4 STEP1 STEP2 prior to first cycle only HBK073 optional sub-cycle if specified (2.3); sub-cycle performed during any 5 of the first 9 cycles; humidity uncontrolled during sub-cycle circulation of conditioning air shall be at a minimum cubic rate per minute equivalent to 10 times the volume of the chamber STEP3 STEP4 STEP5 STEP6 STEP7 one cycle 24 hours; repeat as specified in 2.5 0 5 10 15 20 25 time [h] Fig. 7 Moisture resistance test requirements www.yageo.com May 30, 2005 V.1 Product specification Chip Resistor Surface Mount RJ SERIES 10 10 0201 to 2512 (Pb Free) REVISION HISTORY REVISION DATE Version 1 CHANGE NOTIFICATION May 30, 2005 - DESCRIPTION - New datasheet for thin film general purpose chip resistors sizes of 0201/0402/0603/0805/1206/1210/2010/2512 1% , TC50 with lead-free terminations www.yageo.com May 30, 2005 V.1