Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
Standard Features
Low-voltage and Standard-voltage Operation
VCC = 1.7V to 5.5V
Internally Organized as 512 x 8 (4K), or 1024 x 8 (8K)
I2C-compatible (2-wire) Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
1MHz (2.5V, 2.7V, 5V), 400kHz (1.7V) Compatibility
Write Protect Pin for Hardware Data Protection
16-byte Page Write Mode
Partial Page Writes Allowed
Self-timed Write Cycle (5ms Max)
High-reliability
Endurance: 1,000,000 Write Cycles
Data Retention: 100 Years
Green Package Options (Pb/Halide-free/RoHS Compliant)
8-lead PDIP, 8-lead SOIC, 8-lead TSSOP, 8-pad UDFN, 5-lead SOT23,
and 8-ball VFBGA
Die Options: Wafer Form and Tape and Reel
Description
The Atmel® AT24C04C and AT24C08C provides 4,096/8,192 bits of Serial
Electrically Erasable and Programmable Read-Only Memory (EEPROM)
organized as 512/1024 words of 8 bits each. The device is optimized for use in
many industrial and commercial applications where low-power and low-voltage
operation are essential. AT24C04C/08C is available in space-saving 8-lead PDIP,
8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, 5-lead SOT23, and 8-ball
VFBGA packages and is accessed via a 2-wire serial interface.
AT24C04C and AT24C08C
I2C-Compatible, (2-wire) Serial EEPROM
4-Kbit (512 x 8), 8-Kbit (1024 x 8)
DATASHEET
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
2
1. Pin Configurations and Pinouts
Notes: 1. For use of 5-lead SOT23, the
software A2 and A1 bits in the
device address word must be set
to zero to properly communicate.
2. Drawings are note to scale.
2. Absolute Maximum Ratings
Pin Name Function
NC No Connect
A1Address Input (4K Only)
A2Address Input
SDA Serial Data
SCL Serial Clock Input
WP Write Protect
GND Ground
VCC Power Supply
1
2
3
4
NC
A1/NC
A2
GND
8
7
6
5
VCC
WP
SCL
SDA
8-pad UDFN
(Top View)
8-lead TSSOP
(Top View)
1
2
3
4
8
7
6
5
NC
A
1/NC
A2
GND
VCC
WP
SCL
SDA
1
2
3
4
NC
A1/NC
A2
GND
8
7
6
5
VCC
WP
SCL
SDA
8-lead SOIC
(Top View)
5-lead SOT23
(Top View)
SCL
GND
SDA
WP
VCC
1
2
3
5
4
NC
A1/NC
A2
GND
VCC
WP
SCL
SDA
1
2
3
4
8
7
6
5
8-ball VFBGA
(Top View)
8-lead PDIP
(Top View)
NC
A1/NC
A2
GND
VCC
WP
SCL
SDA
1
2
3
4
8
7
6
5
Operating Temperature . . . . . . . . . . .-55C to +125C
Storage Temperature . . . . . . . . . . . . .-65C to +150C
Voltage on any pin
with respect to ground . . . . . . . . . . . . . -1.0V to +7.0V
Maximum Operating Voltage . . . . . . . . . . . . . . . 6.25V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . .5.0mA
*Notice: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent
damage to the device. This is a stress rating only
and functional operation of the device at these or
any other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
3
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
3. Block Diagram
Start
Stop
Logic
Data Word
ADDR/Counter
Row Decoder
Device
Address
Comparator
Data Latches
DOUT / ACK
Logic
Column
Decoder
EEPROM
Array
Serial
Control
Logic
High Voltage
Pump & Timing
Serial MUX
Read/Write
Enable
COMP Load
INC
V
CC
GND
WP
SCL
SDA
DOUT
DIN
A
2
A
1
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
4
4. Pin Description
Serial Clock (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative
edge clock data out of each device.
Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may
be wire-ORed with any number of other open-drain or open-collector devices.
Device/Page Addresses (A2 and A1): The AT24C04C uses the A2 and A1 inputs for hard wire addressing
allowing a total of four 4K devices to be addressed on a single bus system. Pin 1 is a no connect and can be
connected to ground (see Section 7. “Device Addressing” on page 10). The AT24C08C only uses the A2 input
for hardware addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1
pins are no connects and can be connected to ground (see Section 7.).
Write Protect (WP): AT24C04C/08C has a Write Protect pin that provides hardware data protection. The Write
Protect pin allows normal read/write operations when connected to Ground (GND). When the Write Protect pin
is connected to VCC, the write protection feature is enabled and operates as shown in Table 4-1.
Table 4-1. Write Protect
WP Pin Status Part of the Array Protected
At VCC Full array
At GND Normal read/write operations
5
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
5. Memory Organization
AT24C04C, 4K Serial EEPROM: Internally organized with 32 pages of 16 bytes each, the 4K requires a 9-bit
data word address for random word addressing.
AT24C08C, 8K Serial EEPROM: Internally organized with 64 pages of 16 bytes each, the 8K requires a 10-bit
data word address for random word addressing.
Table 5-1. Pin Capacitance(1)
Note: 1. This parameter is characterized and is not 100% tested.
Table 5-2. DC Characteristics
Note: 1. VIL min and VIH max are reference only and are not tested.
Applicable over recommended operating range from TA = 25°C, f = 1.0MHz, VCC = +1.7V to +5.5V.
Symbol Test Condition Max Units Conditions
CI/O Input/Output capacitance (SDA) 8 pF VI/O = 0V
CIN Input capacitance (A0, A1, A2, SCL) 6 pF VIN = 0V
Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = +1.7V to +5.5V (unless otherwise noted).
Symbol Parameter Test Condition Min Typ Max Units
VCC1 Supply Voltage 1.7 5.5 V
VCC2 Supply Voltage 4.5 5.5 V
ICC Supply Current VCC = 5.0V Read at 100kHz 0.4 1.0 mA
ICC Supply Current VCC = 5.0V Write at 100kHz 2.0 3.0 mA
ISB1 Standby Current VCC = 1.7V VIN = VCC or VSS 1.0 μA
ISB2 Standby Current VCC = 5.5V VIN = VCC or VSS 6.0 μA
ILI Input Leakage Current VIN = VCC or VSS 0.10 3.0 μA
ILO Output Leakage Current VOUT = VCC or VSS 0.05 3.0 μA
VIL Input Low Level(1) -0.6 VCC x 0.3 V
VIH Input High Level(1) VCC x 0.7 VCC + 0.5 V
VOL2 Output Low Level VCC = 3.0V IOL = 2.1mA 0.4 V
VOL1 Output Low Level VCC = 1.7V IOL = 0.15mA 0.2 V
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
6
Table 5-3. AC Characteristics
Note: 1. This parameter is ensured by characterization only.
Applicable over recommended operating range from TAI = -40C to +85C, VCC = +1.7V to +5.5V, CL = 1TTL Gate and 100pF
(unless otherwise noted).
Symbol Parameter
1.7V 2.5V, 2.7V, 5.0V
UnitsMin Max Min Max
fSCL Clock Frequency, SCL 400 1000 kHz
tLOW Clock Pulse Width Low 1.2 0.4 μs
tHIGH Clock Pulse Width High 0.6 0.4 μs
tINoise Suppression Time 100 50 ns
tAA Clock Low to Data Out Valid 0.1 0.9 0.05 0.55 μs
tBUF
Time the bus must be free before a new
transmission can start. 1.2 0.5 μs
tHD.STA Start Hold Time 0.6 0.25 μs
tSU.STA Start Setup Time 0.6 0.25 μs
tHD.DAT Data In Hold Time 0 0 μs
tSU.DAT Data In Setup Time 100 100 ns
tRInputs Rise Time(1) 0.3 0.3 μs
tFInputs Fall Time(1) 300 100 ns
tSU.STO Stop Setup Time 0.6 .25 μs
tDH Data Out Hold Time 50 50 ns
tWR Write Cycle Time 5 5 ms
Endurance(1) 3.3V, +25C, Page Mode 1,000,000 Write Cycles
7
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
6. Device Operation
Clock and Data Transitions: The SDA pin is normally pulled high with an external device. Data on the SDA pin
may change only during SCL low time periods. Data changes during SCL high periods will indicate a Start or
Stop condition as defined below.
Figure 6-1. Data Validity
Start Condition: A high-to-low transition of SDA with SCL high is a Start condition which must precede any
other command.
Stop Condition: A low-to-high transition of SDA with SCL high is a Stop condition. After a read sequence, the
Stop command will place the EEPROM in a standby power mode.
Figure 6-2. Start and Stop Definition
SDA
SCL
Data Stable Data Stable
Data
Change
SDA
SCL
Start Stop
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
8
Acknowledge: All addresses and data words are serially transmitted to and from the EEPROM in eight bit
words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the
ninth clock cycle.
Figure 6-3. Output Acknowledge
Standby Mode: The Atmel AT24C04/08C features a low-power standby mode which is enabled:
Upon power-up.
After the receipt of the Stop condition and the completion of any internal operations.
2-wire Software Reset: After an interruption in protocol, power loss or system reset, any 2-wire part can be
reset by following these steps:
1. Create a Start condition (if possible).
2. Clock nine cycles.
3. Create another Start condition followed by Stop condition as shown below.
The device should be ready for the next communication after above steps have been completed. In the event
that the device is still non-responsive or remains active on the SDA bus, a power cycle must be used to reset
the device.
Figure 6-4. Software Reset
SCL
DATA IN
DATA OUT
Start Acknowledge
9
8
1
SCL 9
Start
Condition Start
Condition
Stop
Condition
8321
SDA
Dummy Clock Cycles
9
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
Figure 6-5. Bus Timing
SCL: Serial Clock, SDA: Serial Data I/O
Figure 6-6. Write Cycle Timing
SCL: Serial Clock, SDA: Serial Data I/O
Notes: 1. The write cycle time tWR is the time from a valid Stop condition of a write sequence to the end of the internal
clear/write cycle.
SCL
SDA IN
SDA OUT
tF
tHIGH
tLOW tLOW
tR
tAA tDH tBUF
tSU.STO
tSU.DAT
tHD.DAT
tHD.STA
tSU.STA
tWR
(1)
Stop
Condition
Start
Condition
WORDn
ACK
8th bit
SCL
SDA
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
10
7. Device Addressing
Standard EEPROM Access: The 4K and 8K EEPROM device requires an 8-bit device address word following
a start condition to enable the chip for a read or write operation. The device address word consists of a
mandatory “1010” (0xA) sequence for the first four Most Significant Bits (MSB) as shown in Figure 7-1. This is
common to all the EEPROM devices.
The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address
bit. The two device address bits must compare to their corresponding hard-wired input pins. The A0 pin is no
connect.
The 8K EEPROM only uses the A2 device address bit with the next two bits being for memory page addressing.
The A2 address bit must compare to its corresponding hard-wired input pin. The A1 and A0 pins are no connect.
The eighth bit of the device address is the read/write operation select bit. A read operation is initiated if this bit is
high and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the chip will
return to a standby state.
For the SOT23 package offering, the 4K EEPROM software A2 and A1 bits in the device address word must be
set to zero to properly communicate. The 8K EEPROM software A2 bit in the device address word must be set
to zero to properly communicate.
Figure 7-1. Device Address
Density Access Area Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
4K EEPROM 1 0 1 0 A2A1P0 R/W
8K EEPROM 1 0 1 0 A2P1 P0 R/W
MSB LSB
11
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
8. Write Operations
Byte Write: A write operation requires an 8-bit data word address following the device address word and
acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in
the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the
addressing device, such as a microcontroller, must terminate the write sequence with a Stop condition. At this
time the EEPROM enters an internally timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled
during this write cycle and the EEPROM will not respond until the write is complete.
Figure 8-1. Byte Write
Page Write: The 4K and 8K EEPROM devices are capable of a 16-byte Page Write.
A Page Write is initiated in the same way as a Byte Write, but the microcontroller does not send a Stop condition
after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word,
the microcontroller can transmit up to fifteen more data words. The EEPROM will respond with a zero after each
data word received. The microcontroller must terminate the Page Write sequence with a Stop condition.
The data word address lower four bits are internally incremented following the receipt of each data word. The
higher data word address bits are not incremented, retaining the memory page row location. When the word
address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the
same page. If more than 16 data words are transmitted to the EEPROM, the data word address will “roll over”
and previous data will be overwritten.
Figure 8-2. Page Write
Acknowledge Polling: Once the internally timed write cycle has started and the EEPROM inputs are disabled,
Acknowledge Polling can be initiated. This involves sending a Start condition followed by the device address
word. The Read/Write bit is representative of the operation desired. Only if the internal write cycle has
completed will the EEPROM respond with a zero allowing the read or write sequence to continue.
SDA LINE
S
T
A
R
T
W
R
I
T
E
S
T
O
P
Device
Address Word Address Data
M
S
B
A
C
K
A
C
K
A
C
K
R
/
W
SDA LINE
S
T
A
R
T
W
R
I
T
E
S
T
O
P
Device
Address
Word
Address (n) Data (n) Data (n + 1) Data (n + x)
M
S
B
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
R
/
W
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
12
9. Read Operations
Read operations are initiated in the same way as write operations with the exception that the read/write select
bit in the device address word is set to one. There are three read operations: Current Address Read, Random
Address Read, and Sequential Read.
Current Address Read: The internal data word address counter maintains the last address accessed during
the last read or write operation, incremented by one. This address stays valid between operations as long as the
chip power is maintained. The address roll-over during read is from the last byte of the last memory page to the
first byte of the first page. The address roll-over during write is from the last byte of the current page to the first
byte of the same page.
Once the device address with the read/write select bit set to one is clocked in and acknowledged by the
EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an
input zero but does generate a following stop condition.
Figure 9-1. Current Address Read
Random Read: A random read requires a “dummy” byte write sequence to load in the data word address. Once
the device address word and data word address are clocked in and acknowledged by the EEPROM, the
microcontroller must generate another start condition. The microcontroller now initiates a Current Address Read
by sending a device address with the read/write select bit high. The EEPROM acknowledges the device
address and serially clocks out the data word. The microcontroller does not respond with a zero but does
generate a following stop condition.
Figure 9-2. Random Read
SDA LINE
S
T
A
R
T
R
E
A
D
S
T
O
P
Device
Address Data
M
S
B
A
C
K
N
O
A
C
K
R
/
W
SDA LINE
S
T
A
R
T
S
T
A
R
T
R
E
A
D
W
R
I
T
E
S
T
O
P
Device
Address
Device
Address
Word
Address (n) Data (n)
M
S
B
A
C
K
A
C
K
A
C
K
N
O
A
C
K
R
/
W
Dummy Write
13
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
Sequential Read: Sequential Reads are initiated by either a Current Address Read or a Random Address
Read. After the microcontroller receives a data word, it responds with an Acknowledge. As long as the
EEPROM receives an Acknowledge, it will continue to increment the data word address and serially clock out
sequential data words. When the memory address limit is reached, the data word address will roll-over and the
Sequential Read will continue. The Sequential Read operation is terminated when the microcontroller does not
respond with a zero but does generate a following Stop condition.
Figure 9-3. Sequential Read
SDA LINE
R
E
A
D
S
T
O
P
Device
Address Data (n) Data (n + 1) Data (n + 2) Data (n + x)
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
R
/
W
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
14
10. Ordering Code Detail
Atmel Designator
Product Family
Device Density
Device Revision
Shipping Carrier Option
Operating Voltage
04 = 4K
08 = 8K
24C = Standard Serial EEPROM
B or blank = Bulk (Tubes)
T = Tape and Reel, Standard Quantity Option
E = Tape and Reel, Expanded Quantity Option
M = 1.7V to 5.5V
Package Device Grade or
Wafer/Die Thickness
H = Green, NiPdAu Lead Finish,
Industrial Temperature Range
(-40˚C to +85˚C)
U = Green, Matte Sn Lead Finish,
Industrial Temperature Range
(-40˚C to +85˚C)
11 = 11mil Wafer Thickness
Package Option
P = PDIP
SS = JEDEC SOIC
X = TSSOP
MA = UDFN
ST = SOT23
C = VFBGA
WWU = Wafer Unsawn
AT24C04C-SSHM-B
15
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
11. Product Markings
DRAWING NO. REV. TITLE
24C04-08CSM C
12/7/16
24C04-08CSM, AT24C04C and AT24C08C Package Marking
Information
Package Mark Contact:
DL-CSO-Assy_eng@atmel.com
AAAAAAAA
###% @
ATMLHYWW
8-lead SOIC 8-lead TSSOP
AAAAAAA
###% @
ATHYWW
8-pad UDFN
###
H%@
YXX
2.0 x 3.0 mm Body
Note 2: Package drawings are not to scale
Note 1: designates pin 1
AT24C04C and AT24C08C: Package Marking Information
Catalog Number Truncation
AT24C04C Truncation Code ###: 04C / ##: 4C
AT24C08C Truncation Code ###: 08C / ##: 8C
Date Codes Voltages
Y = Year M = Month WW = Work Week of Assembly % = Minimum Voltage
6: 2016 0: 2020 A: January 02: Week 2 M: 1.7V min
7: 2017 1: 2021 B: February 04: Week 4
8: 2018 2: 2022 ... ...
9: 2019 3: 2023 L: December 52: Week 52
Country of Assembly Lot Number Grade/Lead Finish Material
@ = Country of Assembly AAA...A = Atmel Wafer Lot Number U: Industrial/Matte Tin/SnAgCu
H: Industrial/NiPdAu
Trace Code Atmel Truncation
XX = Trace Code (Atmel Lot Numbers Correspond to Code) AT: Atmel
Example: AA, AB.... YZ, ZZ ATM: Atmel
ATML: Atmel
5-lead SOT-23
AAAAAAAA
###% @
ATMLUYWW
8-lead PDIP
##@%U
YMXX
Note 3: For SOT23 package with date codes before 7B, the bottom line (YMXX) is marked on the bottom side and there is no Country of Assembly (
@
) mark on the top line.
1.5 x 2.0 mm Body
8-ball VFBGA
PIN 1
###U
YMXX
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
16
12. Ordering Information
Note: 1. For Wafer sales, please contact Atmel Sales.
Atmel Ordering Code Lead Finish Package
Delivery Information
Operation
Range
Form Quantity
AT24C04C-SSHM-B
NiPdAu
(Lead-free/Halogen-free)
8S1
Bulk (Tubes) 100 per Tube
Industrial
Temperature
(-40C to 85C)
AT24C04C-SSHM-T Tape and Reel 4,000 per Reel
AT24C04C-XHM-B
8X
Bulk (Tubes) 100 per Tube
AT24C04C-XHM-T Tape and Reel 5,000 per Reel
AT24C04C-MAHM-T
8MA2
Tape and Reel 5,000 per Reel
AT24C04C-MAHM-E Tape and Reel 15,000 per Reel
AT24C04C-PUM Matte Tin
(Lead-free/Halogen-free)
8P3 Bulk (Tubes) 50 per Tube
AT24C04C-STUM-T 5TS1 Tape and Reel 5,000 per Reel
AT24C04C-CUM-T SnAgCu Ball
(Lead-free/Halogen-free) 8U3-1 Tape and Reel 5,000 per Reel
AT24C04C-WWU11M(1) N/A Wafer Sale Note 1
AT24C08C-SSHM-B
NiPdAu
(Lead-free/Halogen-free)
8S1
Bulk (Tubes) 100 per Tube
Industrial
Temperature
(-40C to 85C)
AT24C08C-SSHM-T Tape and Reel 4,000 per Reel
AT24C08C-XHM-B
8X
Bulk (Tubes) 100 per Tube
AT24C08C-XHM-T Tape and Reel 5,000 per Reel
AT24C08C-MAHM-T
8MA2
Tape and Reel 5,000 per Reel
AT24C08C-MAHM-E Tape and Reel 15,000 per Reel
AT24C08C-PUM Matte Tin
(Lead-free/Halogen-free)
8P3 Bulk (Tubes) 50 per Tube
AT24C08C-STUM-T 5TS1 Tape and Reel 5,000 per Reel
AT24C08C-CUM-T SnAgCu Ball
(Lead-free/Halogen-free) 8U3-1 Tape and Reel 5,000 per Reel
AT24C08C-WWU11M(1) N/A Wafer Sale Note 1
Package Type
8P3 8-lead, 0.300" wide, Plastic Dual Inline Package (PDIP)
8S1 8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8X 8-lead, 4.4mm body, Plastic Thin Shrink Small Outline Package (TSSOP)
8MA2 8-pad, 2.00mm x 3.00mm body, 0.50mm pitch, Plastic Ultra Thin Dual Flat No Lead (UDFN)
5TS1 5-lead, 2.90mm x 1.60mm body, Plastic Thin Shrink Small Outline (SOT23)
8U3-1 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch, Die Ball Grid Array (VFBGA)
17
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
13. Packaging Information
13.1 8P3 — 8-lead PDIP
DRAWING NO. REV. TITLE GPC
Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
D
D1
E
E1
e
L
b2
b
A2 A
1
N
eA
c
b3
4 PLCS
A - - 5.334 2
A1 0.381 - -
A2 2.921 3.302 4.953
b 0.356 0.457 0.559 5
b2 1.143 1.524 1.778 6
b3 0.762 0.991 1.143 6
c 0.203 0.254 0.356
D 9.017 9.271 10.160 3
D1 0.127 0.000 0.000 3
E 7.620 7.874 8.255 4
E1 6.096 6.350 7.112 3
e 2.540 BSC
eA 7.620 BSC 4
L 2.921 3.302 3.810 2
Top View
Side View
End View
Package Drawing Contact:
packagedrawings@atmel.com
A1
Gage Plane
.381
8P3 E
07/31/14
8P3, 8-lead, 0.300” Wide Body, Plastic Dual
In-line Package (PDIP) PTC
v0.254
mC
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
18
13.2 8S1 — 8-lead JEDEC SOIC
DRAWING NO. REV. TITLE GPC
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A1 0.10 – 0.25
A 1.35 – 1.75
b 0.31 – 0.51
C 0.17 – 0.25
D 4.80 – 5.05
E1 3.81 – 3.99
E 5.79 – 6.20
e 1.27 BSC
L 0.40 – 1.27
Ø
Ø
0° – 8°
Ø
E
1
N
TOP VIEW
C
E1
END VIEW
A
b
L
A1
e
D
SIDE VIEW
Package Drawing Contact:
packagedrawings@atmel.com
8S1 G
6/22/11
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC) SWB
19
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
13.3 8X — 8-lead TSSOP
DRAWING NO. REV. TITLE GPC
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A - - 1.20
A1 0.05 - 0.15
A2 0.80 1.00 1.05
D 2.90 3.00 3.10 2, 5
E 6.40 BSC
E1 4.30 4.40 4.50 3, 5
b 0.19 0.25 0.30 4
e 0.65 BSC
L 0.45 0.60 0.75
L1 1.00 REF
C 0.09 - 0.20
Side View
End View
Top View
A2
A
L
L1
D
1
E1
N
b
Pin 1 indicator
this corner
E
e
Notes: 1. This drawing is for general information only.
Refer to JEDEC Drawing MO-153, Variation AA, for proper
dimensions, tolerances, datums, etc.
2. Dimension D does not include mold Flash, protrusions or gate
burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15mm (0.006in) per side.
3. Dimension E1 does not include inter-lead Flash or protrusions.
Inter-lead Flash and protrusions shall not exceed 0.25mm
(0.010in) per side.
4. Dimension b does not include Dambar protrusion.
Allowable Dambar protrusion shall be 0.08mm total in excess
of the b dimension at maximum material condition. Dambar
cannot be located on the lower radius of the foot. Minimum
space between protrusion and adjacent lead is 0.07mm.
5. Dimension D and E1 to be determined at Datum Plane H.
Package Drawing Contact:
packagedrawings@atmel.com
8X E
2/27/14
8X, 8-lead 4.4mm Body, Plastic Thin
Shrink Small Outline Package (TSSOP) TNR
C
A1
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
20
13.4 8MA2 — 8-pad UDFN
DRAWING NO. REV. TITLE GPC
8MA2 G
11/26/14
8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally
Enhanced Plastic Ultra Thin Dual Flat No-Lead
Package (UDFN)
YNZ
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A 0.50 0.55 0.60
A1 0.0 0.02 0.05
A2 - - 0.55
D 1.90 2.00 2.10
D2 1.40 1.50 1.60
E 2.90 3.00 3.10
E2 1.20 1.30 1.40
b 0.18 0.25 0.30 3
C 1.52 REF
L 0.30 0.35 0.40
e 0.50 BSC
K 0.20 - -
TOP VIEW
SIDE VIEW
BOTTOM VIEW
Package Drawing Contact:
packagedrawings@atmel.com
C
E
Pin 1 ID
D
8
7
6
5
1
2
3
4
A
A1
A2
D2
E2
e (6x)
L (8x)
b (8x)
Pin#1 ID
K
1
2
3
4
8
7
6
5
Notes: 1. This drawing is for general information only. Refer to
Drawing MO-229, for proper dimensions, tolerances,
datums, etc.
2. The Pin #1 ID is a laser-marked feature on Top View.
3. Dimensions b applies to metallized terminal and is
measured between 0.15 mm and 0.30 mm from the
terminal tip. If the terminal has the optional radius on
the other end of the terminal, the dimension should
not be measured in that radius area.
4. The Pin #1 ID on the Bottom View is an orientation
feature on the thermal pad.
21
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
13.5 5TS1 — 5-lead SOT23
DRAWING NO. REV. TITLE GPC
Package Drawing Contact:
packagedrawings@atmel.com
5TS1 D
5/31/12
5TS1, 5-lead 1.60mm Body, Plastic Thin
Shrink Small Outline Package (Shrink SOT) TSZ
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL MIN NOM MAX NOTE
A - - 1.00
A1 0.00 - 0.10
A2 0.70 0.90 1.00
c 0.08 - 0.20 3
D 2.90 BSC 1,2
E 2.80 BSC 1,2
E1 1.60 BSC 1,2
L1 0.60 REF
e 0.95 BSC
e1 1.90 BSC
b 0.30 - 0.50 3,4
1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash,
protrusions or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does
not include interlead flash or protrusion. Interlead flash or protrusion shall not
exceed 0.15 mm per side.
2. The package top may be smaller than the package bottom. Dimensions D and E1
are determined at the outermost extremes of the plastic body exclusive of mold
flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch
between the top and bottom of the plastic body.
3. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15
mm from the lead tip.
4. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion
shall be 0.08 mm total in excess of the "b" dimension at maximum material
condition. The dambar cannot be located on the lower radius of the foot. Minimum
space between protrusion and an adjacent lead shall not be less than 0.07 mm.
This drawing is for general information only. Refer to JEDEC
Drawing MO-193, Variation AB for additional information.
54
2
L1
L
C
END VIEW
C
A
A2
A1
b
e
PLANE
SEATING
D
SIDE VIEW
E
e1
E1
3
1
TOP VIEW
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
22
13.6 8U3-1 — 8-ball VFBGA
DRAWING NO. REV. TITLE GPC
Package Drawing Contact:
packagedrawings@atmel.com
8U3-1 F
6/11/13
8U3-1, 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch,
Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA) GXU
COMMON DIMENSIONS
(Unit of Measure - mm)
SYMBOL MIN NOM MAX NOTE
A
0.73 0.79 0.85
A1 0.09 0.14 0.19
A2 0.40 0.45 0.50
b 0.20 0.25 0.30 2
D
1.50 BSC
E
2.0 BSC
e
0.50 BSC
e1 0.25 REF
d
1.00 BSC
d1 0.25 REF
1. This drawing is for general information only.
2. Dimension ‘b’ is measured at maximum solder ball diameter.
3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu.
Notes:
A2
SIDE VIEW
A
PIN 1 BALL PAD CORNER
TOP VIEW
E
D
A1
b
8 SOLDER BALLS
BOTTOM VIEW
(d1)
d
4
3
2
(e1)
6
e
5
7
PIN 1 BALL PAD CORNER
1
8
2.
23
AT24C04C/08C [DATASHEET]
Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016
14. Revision History
Doc. Rev. Date Comments
8787F 12/2016
Part marking SOT23:
- Moved backside mark (YMXX) to front side line2.
- Added @ = Country of Assembly.
8787E 01/2015
Add the UDFN expanded quantity options and update the ordering information section.
No change in functional or electrical specification. Update the 8P3, 8X, 8MA2, and 8U3-1
package outline drawings and the disclaimer page.
8787D 04/2013 In the Page Write description, correct from eight to 16 data words.
Update ordering code table, footers, and disclaimer page.
8787C 07/2012
Correct ordering codes:
- AT24C04C-WWU11, Die Sale to AT24C04C-WWU11M, Wafer Sale.
- AT24C08C-WWU11, Die Sale to AT24C08C-WWU11M, Wafer Sale.
Remove WDT from ordering code detail.
Update Atmel logos and disclaimer page.
8787B 05/2012
Remove preliminary status.
Remove A0 signal from the block diagram.
ISB2 parameter measured at 5.5V.
In AC Characteristics table, changed 1.7V, 2.5V, 2.7V to 1.7 and 5.0V to 2.5V, 2.7V, 5.0V.
Increase tI maximum value from 50ns to 100ns.
Endurance parameter is studied at 3.3V, to +25C, Page mode.
Remove Serial Number Read from read operations.
Update product markings.
Update 8X and 8U3-1 package drawings.
Update template.
8787A 10/2011 Initial document release.
X
XXX
XX
Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com
© 2015 Atmel Corporation. / Rev.: Atmel-8787F-SEEPROM-AT24C04C-08C-Datasheet_122016.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
