MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Rev. V4 Features Functional Schematic Gain: 22 dB P1dB: 27 dBm High Linearity, OIP3: 38 dBm Integrated Power Detector Lead-Free 7 mm Laminate Package RoHS* Compliant and 260C Reflow Compatible Description The MAAP-010512 is a 4-stage, high linearity 1W power amplifier in a 7x7 mm laminate package, allowing easy assembly. This PA product is fully matched to 50 ohms on both the input and output. It is designed for use as a power amplifier stage in transmit chains and is ideally suited for 42 GHz band point-to-point radios. Each device is 100% RF tested to ensure performance compliance. The part is fabricated using an efficient pHEMT process. Pin Configuration 1,2 Pin No. Function Pin No. Function 1 RFIN 9 RFOUT Ordering Information Part Number Package 2 VG1 10 VD3 MAAP-010512-000000 Bulk quantity 3 VG2 11 VD2 MAAP-010512-TR0200 200 Piece Reel 4 VG3 12 VD1 MAAP-010512-TR0500 500 Piece Reel 5 No Connection 13 No Connection MAAP-010512-001SMB Sample Evaluation board 6 No Connection 14 No Connection 7 VREFERENCE 15 No Connection 8 VDETECTOR 16 No Connection Paddle Ground 1. MACOM recommends connecting unused package pins to ground. 2. The exposed pad centered on the package bottom must be connected to RF and DC ground. * Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Rev. V4 Electrical Specifications: Freq: 40.5 - 43.5 GHz, VD = 4 V, ID1 = 217 mA, ID2 = 300 mA, ID3 = 600 mA, T A = 25C Parameter Units Min. Typ. Max. Small Signal Gain dB 18.0 22.0 27.0 Gain Flatness cross Band dB - +/-1.0 - Input Return Loss dB - 15 - Output Return Loss dB - 12 - Reverse Isolation dB - 50 - Output P1dB dBm - 27.0 - Output IP3 dBm 32.5 38.0 - Saturated Output Power dBm 25.0 29.0 - Output IMD3 with Pout (scl) = 14 dBm dBc 37.0 48.0 - Supply Current3 mA - 1117 1300 3. Adjust Vgs between -1.0 V and -0.1 V to achieve specified supply current. Typical current 1117 mA = 217 (ID1) + 300 (ID2) + 600 (ID3) Absolute Maximum Ratings 4,5,6 Parameter Absolute Max. Drain Voltage +4.3 V Gate Bias Voltage -1.5 V < Vg < 0 V Input Power 15 dBm Junction Temperature7 150C Operating Temperature -40C to +85C Storage Temperature -55C to +150C Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these Human Body Model Class 1A devices. 4. Exceeding any one or combination of these limits may cause permanent damage to this device. 5. M/A-COM Technology Solutions does not recommend sustained operation near these survivability limits. 6. Operating at nominal conditions with TJ 150C will ensure MTTF > 1 x 106 hours. 7. Junction Temperature (TJ) = TC + jc * (V * I) Typical thermal resistance (jc) = 11.2 C/W. a) For TC = 25C, TJ = 75C @ 4 V, 1117 mA b) For TC = 85C, TJ = 135C @ 4 V, 1117 mA 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Rev. V4 Typical Performance Curves: VD = 4 V, ID1 = 217 mA, ID2 = 300 mA, ID3 = 600 mA, T A = 25C Small Signal Gain Input Return Loss 0 40 -5 30 -10 20 -15 +25C -40C +85C 10 0 40.5 41.0 41.5 42.0 42.5 -20 43.0 43.5 -25 40.5 41.0 41.5 0 -30 -5 -40 -10 -50 -15 -60 -20 -70 41.0 42.5 43.0 43.5 43.0 43.5 43.0 43.5 Reverse Isolation Output Return Loss -25 40.5 42.0 Frequency (GHz) Frequency (GHz) 41.5 42.0 42.5 43.0 43.5 -80 40.5 41.0 41.5 42.0 42.5 Frequency (GHz) Frequency (GHz) Output IP3 (Pout = 14 dBm SCL) C/I3 (Pout = 14 dBm SCL) 44 54 +25C -40C +85C 42 40 50 38 48 36 46 34 40.5 41.0 41.5 +25C -40C +85C 52 42.0 42.5 Frequency (GHz) 43.0 43.5 44 40.5 41.0 41.5 42.0 42.5 Frequency (GHz) 3 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Rev. V4 Typical Performance Curves: VD = 4 V, ID1 = 217 mA, ID2 = 300 mA, ID3 = 600 mA, T A = 25C Psat P1dB 34 32 +25C -40C +85C 30 28 30 26 28 24 26 22 40.5 41.0 +25C -40C +85C 32 41.5 42.0 42.5 43.0 43.5 Frequency (GHz) 24 40.5 41.0 41.5 42.0 42.5 43.0 Frequency (GHz) Detector Output (Diff), Vdet/ref Bias = +5V100k 10 1 1 0.1 40.5 GHz 42.0 GHz 43.5 GHz 0.01 0.001 -15 -10 -5 0 5 10 15 20 25 30 Output Power (dBm) 4 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support 43.5 MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Rev. V4 App Note [1] Biasing - It is recommended to bias the amplifier with Vd=4.0 V and Id=1117 mA. It is also recommended to use active biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. The gate of the pHEMT is controlled to maintain correct drain current and thus drain voltage. The typical gate voltage needed to do this is -0.3 V. Typically the gate is protected with Silicon diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying the positive drain supply. App Note [2] Bias Arrangement - Each DC pin (Vd1,2,3 and Vg1,2,3) needs to have DC bypass capacitance (10 nF/1 F) as close to the package as possible. App Note [3] Power Detector - As shown in the schematic below, the power detector is implemented by providing +5 V bias and measuring the difference in output voltage with standard op-amp in a differential mode configuration. Recommended Board Layout 5 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Lead-Free 7 mm x 7mm Laminate Package Reference Application Note S2083 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 3 requirements. 6 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support Rev. V4 MAAP-010512 Amplifier, Power, 0.8 W 40.5 - 43.5 GHz Rev. V4 M/A-COM Technology Solutions Inc. All rights reserved. Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM") products. These materials are provided by MACOM as a service to its customers and may be used for informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM assumes no responsibility for errors or omissions in these materials. MACOM may make changes to specifications and product descriptions at any time, without notice. MACOM makes no commitment to update the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this document. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE OF THESE MATERIALS. MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM customers using or selling MACOM products for use in such applications do so at their own risk and agree to fully indemnify MACOM for any damages resulting from such improper use or sale. 7 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: https://www.macom.com/support