Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz mixers - Downconverters - SMT 9 Typical Applications Features The HMC683LP6C(E) is Ideal for: High Input IP3: +23 dBm * Cellular/3G & LTE/WiMAX/4G Conversion Gain: 7.5 dB * Basestations & Repeaters Low LO Drive: 0 dBm * GSM, CDMA & OFDM High Channel Isolation * Dual Density Receivers 40 Lead 6x6mm SMT Package: 36mm2 Functional Diagram General Description The HMC683LP6C(E) is a high linearity, dual channel downconverter with integrated LO amplifier in a 6x6 SMT QFN package covering 0.7 - 1.0 GHz. Excellent input IP3 performance of +23 dBm for down conversion is provided for 3G & 4G GSM/CDMA applications at an LO drive of 0 dBm. With an input 1 dB compression of +11 dBm, the RF port will accept a wide range of input signal levels. Conversion gain is 7.5 dB typical. The 60 - 500 MHz IF frequency response will satisfy various GSM/CDMA receive frequency plans. Electrical Specifications, TA = +25 C, IF - 100 MHz, LO = 0 dBm Vcc1, 2 = Vcc_BAL1, 2 = Vcc_AMP1, 2 [1] = Vcc_IF1P, N = Vcc_IF2P, N = +5V, BIAS1, 2 = +2.5V Parameter Min. Typ. Units 700 - 1000 MHz Frequency Range, LO 570 - 900 MHz 60 - 500 MHz Frequency Range, IF Conversion Gain 5 7.5 Noise Figure (SSB) dB 11 dB 10 16 dB LO to IF Isolation 15 20 dB RF to IF Isolation 19 28 dB LO to RF Isolation IP3 (Input) 23 dBm 1 dB Compression (Input) 11 dBm Channel to Channel Isolation 50 dB LO Drive Input Level (Typical) Supply Current (Icc) [1] See Application Circuit 9-1 Max. Frequency Range, RF -3 to +3 420 dBm 520 mA [2] Unless otherwise noted all measurements with low side LO & IF = 100 MHz. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz Single Channel: Isolation 0 10 -10 8 6 +25 C +85 C -40 C 4 2 -20 -30 -40 RF/IF LO/RF LO/IF -50 0 0.6 0.7 0.8 0.9 1 -60 0.6 1.1 0.7 FREQUENCY (GHz) 0 10 -5 8 6 -3 dBm 0 dBm +3 dBm 2 0.7 0.8 0.9 1 1.1 -10 -15 -20 RF1 LO1 LO_SEL 0V LO1 LO_SEL +5V -25 0 0.6 0.9 Single Channel: Return Loss 12 RETURN LOSS (dB) CONVERSION GAIN (dB) 0.8 FREQUENCY (GHz) Single Channel: Conversation Gain vs. LO Drive 4 9 1 -30 0.5 1.1 0.6 FREQUENCY (GHz) 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) mixers - Downconverters - SMT 12 ISOLATION (dB) CONVERSION GAIN (dB) Single Channel: Conversion Gain vs. Temperature Single Channel: Input P1dB vs. Temperature Single Channel: IF Bandwidth 20 15 10 15 0 P1dB (dBm) RESPONSE (dB) 5 IF Return Loss Conversion Gain -5 -10 10 +25 C +85 C -40 C 5 -15 -20 -25 0 0.1 0.2 0.3 FREQUENCY (GHz) 0.4 0.5 0 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 9-2 HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz 30 25 25 20 20 IP3 (dBm) IP3 (dBm) Single Channel: Input IP3 vs. Temperature 30 -3 dBm 0 dBm +3 dBm 15 15 10 10 5 5 0 0.6 0.7 0.8 0.9 1 0 0.6 1.1 +25 C +85 C -40 C 0.7 FREQUENCY (GHz) 0.8 0.9 1 1.1 FREQUENCY (GHz) Dual Channel: Channel to Channel Isolation [1] Dual Channel: LO1 to LO2 Isolation [2] -20 -10 -20 -30 RF1 TO RF2 AT IFI RF2 TO RF1 AT IF2 ISOLATION (dBc) ISOLATION (dBc) mixers - Downconverters - SMT 9 Single Channel: Input IP3 vs. LO Drive -40 -30 -40 -50 -50 -60 -60 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) -70 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) Noise Figure vs. Temperature [1] For 900 MHz, RF1 = 900 MHz @ 0 dBm, RF2 = 901 MHz @ 0 dBm, LO = 800 MHz @ 0 dBm, IF2 terminated with 50 Ohms. Channel isolation is the dBc difference at IF1 port between the fundamental tone @ 100 MHz and the leakage tone @ 101 MHz. 16 NOISE FIGURE (dB) 15 +25 C +85 C -40 C 14 13 [2] For 900 MHz, LO1 = 800 MHz @ 0 dBm, LO2 = 799 MHz @ 0 dBm, LO1 is selected, RF1 = RF2 = 900 MHZ @ 0 dBm, IF2 terminated with 50 Ohms. LO1-LO2 isolation is the dBc difference measured at the IF1 port between the fundamental tone at 100 MHz and the leakage tone @ 101 MHz. 12 11 10 9 8 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) 9-3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz +2RF -2LO Response vs. LO Drive [3] 55 50 +25 C +85 C -40 C 45 40 0.6 0.7 0.8 0.9 1 55 50 40 0.6 1.1 -3 dBm 0 dBm +3 dBm 45 0.7 FREQUENCY (GHz) 75 75 +3RF-3LO RESPONSE (dBc) +3RF-3LO RESPONSE (dBc) 80 70 65 60 +25 C +85 C -40 C 0.7 0.8 0.9 FREQUENCY (GHz) 0.9 1 1.1 +3RF -3LO Response vs. LO Drive [3] 80 55 0.8 FREQUENCY (GHz) +3RF -3LO Response vs. Temperature [3] 50 0.6 9 60 +2RF-2LO RESPONSE (dBc) +2RF-2LO RESPONSE (dBc) 60 1 1.1 70 65 -3 dBm 0 dBm +3 dBm 60 55 50 0.6 0.7 0.8 0.9 1 1.1 FREQUENCY (GHz) mixers - Downconverters - SMT +2RF -2LO Response vs. Temperature [3] [1] Referenced to RF Input Power @ 0 dBm For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 9-4 HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz mixers - Downconverters - SMT 9 MxN Spurious @ IF Port Harmonics of LO nLO nLO Spur @ RF Port mRF 0 1 2 3 4 LO Freq. (GHz) 1 2 3 4 0 xx 23 16 22 28 0.6 17 33 36 37 1 34 0 38 16 45 0.7 15 25 34 39 2 55 50 56 59 82 0.8 17 24 33 30 3 88 57 82 63 88 0.9 20 26 35 25 4 93 94 92 94 94 1.0 21 28 41 54 1.1 23 29 53 57 RF Freq. = 0.9 GHz @ -5 dBm LO Freq. = 0.8 GHz @ 0 dBm All values in dBc below IF power level (1RF - 1LO). Typical Supply Current vs. Vcc LO = 0 dBm All values in dBc below input LO level measured at RF port. Truth Table Vcc Icc (A) LO_SEL (V) 4.75 390 0 LO Signal Path LO1 5.00 420 5 LO2 5.25 450 Downconverter will operate over full voltage range shown above. Absolute Maximum Ratings 9-5 RF / IF Input (Vcc= +5V) +15 dBm LO Drive (Vcc= +5V) +6 dBm Vcc (LO or IF) 5.5V Channel Temperature 12.5C Continuous Pdiss (T = 85C) (derate 110.53 mW/C above 85C) 4.42 W Thermal Resistance (channel to ground paddle) 9.05 C/W Storage Temperature -65 to 150C Operating Temperature -40 to +85 C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY. 3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN. 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 6. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.25mm MAX. 7. PACKAGE WARP SHALL NOT EXCEED 0.05mm 8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. mixers - Downconverters - SMT 9 Package Information Part Number Package Body Material Lead Finish MSL Rating HMC683LP6C Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC683LP6CE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H683 XXXX H683 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 260 C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 9-6 HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz mixers - Downconverters - SMT 9 9-7 Pin Descriptions Pin Number Function Description 1, 10 RF1, RF2 These are the RF inputs of the mixers. See application circuit for the off-chip matching components 2, 9 TAP1, TAP2 These are the center taps of the internal RF baluns. Connect these pins to the AC ground via external capacitors. See application circuit. 3, 5, 8, 15, 16, 22, 23, 26 - 29, 35, 36 GND These pins must be connected to RF ground. 4, 7 BIAS1, BIAS2 Bias pins for mixer cores. See application circuit for the nominal value. 6, 17, 18, 24, 33, 34 Vcc1, Vcc_BAL2, Vcc_AMP2, Vcc2, Vcc_AMP1, Vcc_BAL1 Power supply voltage pins. See application circuit for bypass capacitors required. 11, 20, 31, 40 N/C No Connection required. These pins may be connected to RF GND without affecting performance. 12, 39 IND1, IND2 Current source inductors for IF amplifiers. 13, 14, 38, 37 IF2P, IF2N, IF1P, IF1N Differential IF outputs and DC bias for IF amplifiers. 19, 32 BIAS_ADJ1, BIAS_ADJ2 Adjusts LO buffer amplifies current via external resistor. See application circuit. 21, 30 LO2, LO1 These are LO inputs of the mixers. See application circuit for off-chip matching components. 25 LO_SEL Control voltage for LO1 or LO2 selection. LO1 is selected when LO SEL is set low. LO2 is selected when LO SEL is set high. See application circuit and truth table for low and high voltage levels. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz 9 mixers - Downconverters - SMT Evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 9-8 HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz mixers - Downconverters - SMT 9 9-9 List of Materials for Evaluation PCB 119926 [1] Item Description J1 - J6 PCB Mount SMA Connector J7 - J10 2mm Vertical Molex 8pc Connector L1, L2 51 nH Inductor, 0603 Pkg. L3 - L6 390 nH Inductor, 0603 Pkg. L7, L8 5.1 nH Inductor, 0402 Pkg. L9, L10 3.6 nH Inductor, 0402 Pkg. C7, C8, C26, C38 22 pF Capacitor, 0402 Pkg. C9, C10 10 nF Capacitor, 0603 Pkg. C11, C17, C19, C24, C27, C29, C34, C37, C40, C48, C50 1 nF Capacitor, 0402 Pkg. C12, C15, C16, C18, C20, C25, C28, C30, C35, C36, C39, C47, C49 0.1 F Capacitor, 0603 Pkg. C13, C14, C60 - C63 100 pF Capacitor, 0402 Pkg. C21, C22, C32, C33 0.01 F Capacitor, 0402 Pkg. C51 - C59 0.47 F Capacitor, 0603 Pkg. R7, R8 330 Ohm Resistor, 0603 Pkg. T1, T2 1:1 Transformer - Tyco ETC1-IT U1 HMC683LP6C(E) PCB [2] 118274 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon-25FR adn FR4 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC683LP6C / 683LP6CE v02.0808 HIGH IP3 DUAL CHANNEL DOWNCONVERTER w/ LO SWITCH, 0.7 - 1.0 GHz 9 mixers - Downconverters - SMT Application Circuit For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 9 - 10 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: HMC683LP6CE HMC683LP6CETR 119926-HMC683LP6C