Installation Instructions for the
Basic Board Mount Pressure Sensors
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
60 mbar to 10 bar | 6 kPa to 1 MPa | 1 psi to 150 psi
Sensing and Control
Issue F
50076346
GENERAL INFORMATION
Honeywell’s Basic Board Mount Pressure Sensors: NBP Series,
Uncompensated/Unamplied, and TBP Series, Compensated/
Unamplied, are piezoresistive silicon pressure sensors designed
for customers who require a simple, cost-effective, mV output,
unamplied, high quality, high resolution solution for medical and
industrial applications.
SOLDERING
See soldering times and temperatures in Table 1.
CAUTION
MEDIA INCOMPATIBILITY
•No gel coating option: The input port is limited to non-
corrosive, non-ionic media such as dry air and gases and
should not be exposed to condensation. The gases are
limited to media that are compatible with the following
wetted materials of construction: high temperature
polyamide, silicone, epoxy, alumina ceramic, silicon, gold,
and glass.
•Silicon gel coating option: The gel coated sensors use the
same materials in the wetted media path but are protected
from condensation by a silicone-based gel coating.
The gel coating option allows use in applications where
condensation can occur.
Failure to comply with these instructions may result in
product damage.
CAUTION
IMPROPER CLEANING
•Ensurecleaninguids,suchasappropriatealcohols
oruorinatedsolvents,areusedbasedonthetypeof
contaminants to be removed.
•Donotimmersethesensor.
Failure to comply with these instructions may result in
product damage.
Table 1. Absolute Maximum Ratings1
Characteristic Min. Max. Unit
Supply voltage (Vsupply)2-12.0 12.0 Vdc
Storage temperature -40 [-40] 125 [257] °C [°F]
Soldering time and temperature:
leadsoldertemperature(DIP)
peakreowtemperature(Lead
less SMT, SMT)
4 s max. at 250 °C [482 °F]
15 s max. at 250 °C [482 °F]
1. Absolute maximum ratings are the extreme limits the device will
withstand without damage.
2.Incorrectapplicationofsupplyvoltageorgroundtothewrongpin
may cause electrical failure.
Table 2. Operating Specications
Characteristic Min. Typ. Max. Unit
Supply voltage (Vsupply):1, 2
TBP Series
NBP Series
1. 5
1. 8
5.0
5.0
12.0
12.0
Vdc
Supply current (at 5.0 Vdc supply):
TBP Series
NBP Series
—
—
0.6
1. 5
1. 0
2.5
mA
Operating temperature range3-40 [-40] —125 [257] °C [°F]
Compensated temperature range4 (TBP Series only) 0 [32] —85 [185] °C [°F]
Inputresistance (NBP Series only) 2.4 3.0 5.5 kOhm
1. Ratiometricity of the sensor (the ability of the device output to scale to the supply voltage) is achieved within the specied operating voltage.
2.Incorrectapplicationofsupplyvoltageorgroundtothewrongpinmaycauseelectricalfailure.
3. Operating temperature range: The temperature range over which the sensor will produce an output proportional to pressure.
4. Compensated temperature range: The temperature range over which the sensor will produce an output proportional to pressure within
the specied performance limits.
2 Honeywell Sensing and Control
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Table 3. Environmental Specications
Characteristic Parameter
Humidity:
all external surfaces
internal surfaces of silicon gel coating option
internal surfaces of no coating option
0 %RH to 95 %RH, non-condensing
0 %RH to 100 %RH, condensing
0 %RH to 95 %RH, non-condensing
Vibration MIL-STD-202G,Method204D,ConditionB(15g,10Hzto2kHz)
Shock MIL-STD-202G,Method213B,ConditionC(100g,6msduration)
Life11 million pressure cycles min.
ESD:
TBP Series
NBP Series
MIL-STD883Method3015.7,Class1
MIL-STD883Method3015.7,Class3
Solderreow J-STD-020-D,MSL1(unlimitedshelflifewhenstoredatlessthan30°Cand85%RH)
Notes:
1Lifemayvarydependingonspecicapplicationinwhichthesensorisutilized.
Table 4. Wetted Materials
Component No Gel Coating Option Silicon Gel Coating Option
Ports high temperature polyamide high temperature polyamide
Substrate alumina ceramic not exposed: protected by silicone gel
Adhesives epoxy, RTV epoxy
Electroniccomponents ceramic, silicon, gold, glass not exposed: protected by silicone gel
Honeywell Sensing and Control 3
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Figure 2. DIP Package Dimensional Drawings (For reference only: mm [in].)
AN: Single axial barbed port
LN: Single axial barbless port
PN: Low-prole port
Recommended PCB Pad Layout
11,50
[0.45]
2,54
[0.100
]
Ø 0,813
[0.032]
Table 8. Pinout for DIP Packages
Pin 4 Pin 3
Vout+ GND
Pin 1 Pin 2
Vsupply Vout-
4X 0,46
[0.018]
34
21
7,00
[0.276]
5,50
[0.217]
2,54 TYP.
[0.100]
43
12
3,50
[0.138]
2,23
[0.088] Ø 6,50
[0.256]
10,94 MAX.
[0.430]
11,50
[0.45]
1,02
[0.040]
0,25
[0.010]
8,64
[0.340]
Ø 2,74
[0.108]
Ø 2,32
[0.091]
3,56
[0.140]
Ø 1,91
[0.075]
PIN 1
INDICATO
R
5,50
[0.217]
43
12
3,50
[0.138]
2,23
[0.088]
2,54 TYP.
[0.100] 1,02
[0.040]
8,64
[0.340]
0,25
[0.010]
11,5
[0.45]
10,94 MAX.
[0.430]
Ø 3,18
[0.125]
Ø 6,50
[0.256]
3,84
[0.151]
5,83
[0.230]
4X 0,46
[0.018]
34
21
7,00
[0.276]
PIN 1
INDICATO
R
5,50
[0.217]
2,54 TYP.
[0.100]
34
12
3,50
[0.138]
2,23
[0.088]
11,5
[0.45]
0,25
[0.010]
1,02
[0.040]
8,64
[0.340]
Ø 6,50
[0.256]
3,84
[0.151]
2,10
[0.083]
4X 0,46
[0.018]
34
21
7,00
[0.276]
PIN 1
INDICATO
R
4 Honeywell Sensing and Control
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Figure 3. Leadless SMT Package Dimensional Drawings (For reference only: mm [in])
AN: Single axial barbed port
LN: Single axial barbless port
PN: Low-prole port
7,00
[0.276]
3,50
[0.138]
3,50
[0.138]
3,56
[0.140] 3,84 MAX.
[0.151]
10,94 MAX.
[0.430]
Ø 2,32
[0.091]
Ø 1,91
[0.075]
Ø 2,74
[0.108]
Ø 6,50
[0.256]
7,00
[0.276]
1,02
[0.040] 2,50 TYP.
[0.098]
1,00
[0.039]
3
2
1
4
5
6
PAD 1
INDICATOR
7,00
[0.276]
Ø 6,50
[0.256]
1,02
[0.040]
10,94 MAX.
[0.430]
3,84 MAX.
[0.151]
5,84
[0.230]
Ø 3,18
[0.125]
3,50
[0.138]
3,50
[0.138]
7,00
[0.276]
2,50 TYP.
[0.098]
1,00
[0.039]
3
2
1
4
5
6
PAD 1
INDICATOR
7,00
[0.276]
3,84 MAX.
[0.151]
Ø 6,50
[0.256]
1,02
[0.040]
7,00
[0.276]
3,50
[0.138]
3,50
[0.138] 2,50 TYP.
[0.098]
1,00
[0.039]
3
2
1
4
5
6
PAD 1
INDICATOR
5,46
[0.215]
2,50
[0.098]
1,27
[0.050]
2,54
[0.100]
Table 9. Pinout for Leadless SMT
Pressure Packages
Pad 1 Pad 6
Vsupply Vout+
Pad 2 Pad 5
NC NC
Pad 3 Pad 4
Vout- GND
Recommended PCB Pad Layout
Honeywell Sensing and Control 5
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Figure 4. SMT Package Dimensional Drawings (For reference only: mm [in])
AN: Single axial barbed port
LN: Single axial barbless port
PN: Low-prole port
3,50
[0.138]
2,25
[0.088]
2,54 TYP.
[0.100]
43
12
5,50
[0.217]
3,03
[0.119]
Ø 2,74
[0.108]
Ø 6,50
[0.256]
[0.430]
11,5
[0.45]
3,84
[0.151]
0,25
[0.010]
Ø 2,32
[0.091]
Ø 1,91
[0.075]
1,02
[0.040]
7,00
[0.276]
4X 1,27
[0.050
4X 0,46
[0.018]
34
21
PIN 1
R
7,00
[0.276]
4X 1,27
[0.050]
4X 0,46
[0.018]
34
21
3,50
[0.138]
5,50
[0.217]
43
12
2,25
[0.088]
2,54 TYP.
[0.100]
10,94 MAX.
[0.430]
Ø 6,50
[0.256]
3,84
[0.151]
Ø 3,18
[0.125]
0,25
[0.010]
3,03
[0.119]
1,02
[0.040]
11,5
[0.45]
5,83
[0.230]
PIN 1
INDICATO
R
7,00
[0.276]
4X 1,27
[0.050
]
4X 0,46
[0.018]
34
21
3,50
[0.138]
2,25
[0.088]
5,50
[0.217]
2,54 TYP.
[0.100]
43
12
0,25
[0.010]
3,03
[0.119]
11,5
[0.45]
1,02
[0.040]
Ø 6,50
[0.256]
2,10
[0.083]
3,84 MAX.
[0.151]
PIN 1
INDICATO
R
2,54
[0.100
]
7,59
[0.30]
1,143
[0.045]
2,032
[0.080
]
Table 10. Pinout for SMT Packages
Pin 4 Pin 3
Vout+ GND
Pin 1 Pin 2
Vsupply Vout-
Recommended PCB Pad Layout
6 Honeywell Sensing and Control
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Figure 5. TBP Series Nomenclature and Order Guide
TBP D AN N 150PG U C
V
U
Series
Output
TBP
Unamplified
For example, TBPDANN150PGUCV denes a TBP Series Basic Board Mount Pressure Sensor, DIP package, AN pressure
port, no gel coating in media path,150 psi gage pressure range, unamplied, compensated, constant supply voltage.
D
L
DIP (Dual Inline Pin)
Leadless SMT (Surface Mount Technology)
Package
MSMT (Surface Mount Technology)
Gel Coating Option
DIP Leadless SMT
AN
SMT
LN
PN
Single axial
barbless port
Low-profile
port
Single axial
barbed port
AN
LN
PN
Single axial
barbless port
Low-profile
port
Single axial
barbed port
AN
LN
PN
Single axial
barbless port
Low-profile
port
Single axial
barbed port
C
Compensation
Compensated
V
Supply Voltage
Constant
N
S
No gel coating in media path
Silicone gel coating in media path
Pressure Port
Pressure Range
1 psi to 150 psi60 mbar to 10 bar 6 kPa to 1 MPa
Gage
Gage
001PG
005PG
015PG
030PG
060PG
100PG
150PG
060MG
100MG
160MG
250MG
400MG
600MG
001BG
1.6BG
2.5BG
004BG
006BG
010BG
0 mbar to 60 mbar
0 mbar to 100 mbar
0 mbar to 160 mbar
0 mbar to 250 mbar
0 bar to 400 mbar
0 bar to 600 mbar
0 bar to 1 bar
0 bar to 1.6 bar
0 bar to 2.5 bar
0 bar to 4 bar
0 bar to 6 bar
0 bar to 10 bar
Gage
006KG
010KG
016KG
025KG
040KG
060KG
100KG
160KG
250KG
400KG
600KG
001GG
0
kPa
to 6
kPa
0
kPa
to 10
kPa
0
kPa
to 16
kPa
0
kPa
to 25
kPa
0
kPa
to 40
kPa
0
kPa
to 60
kPa
0
kPa
to 100
kPa
0
kPa
to 160
kPa
0
kPa
to 250
kPa
0
kPa t
o 400
kPa
0
kPa
to 600
kPa
0
kPa t
o 1 MP
a
0 psi to 1 psi
0 psi to 5 psi
0 psi to 15 psi
0 psi to 30 psi
0 psi to 60 psi
0 psi to 100 psi
0 psi to 150 psi
Honeywell Sensing and Control 7
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Figure 6. NBP Series Nomenclature and Order Guide
NBP D AN N 150PG U N
V
U
Series
Output
NBP
Unamplified
For example, NBPDANN150PGUNV denes an NBP Series Basic Board Mount Pressure Sensor, DIP package, AN pressure
port, no gel coating in media path,150 psi gage pressure range, unamplied, uncompensated, constant supply voltage.
D
L
DIP (Dual Inline Pin)
Leadless SMT (Surface Mount Technology)
Package
MSMT (Surface Mount Technology)
Gel Coating Option
N
Compensation
Uncompensated
V
Supply Voltage
Constant
N
S
No gel coating in media path
Silicone gel coating in media path
Pressure Range
1 psi to 150 psi60 mbar to 10 bar
Absolute
Absolute
015PA
030PA
060PA
100PA
150PA
001BA
1.6BA
2.5BA
004BA
006BA
010BA
0 bar to 1 bar
0 bar to 1.6 bar
0 bar to 2.5 bar
0 bar to 4 bar
0 bar to 6 bar
0 bar to 10 bar
0 psi to 15 psi
0 psi to 30 psi
0 psi to 60 psi
0 psi to 100 psi
0 psi to 150 psi
Gage
Gage
001PG
005PG
015PG
030PG
060PG
100PG
150PG
060MG
100MG
160MG
250MG
400MG
600MG
001BG
1.6BG
2.5BG
004BG
006BG
010BG
0 mbar to 60 mbar
0 mbar to 100 mbar
0 mbar to 160 mbar
0 mbar to 250 mbar
0 bar to 400 mbar
0 bar to 600 mbar
0 bar to 1 bar
0 bar to 1.6 bar
0 bar to 2.5 bar
0 bar to 4 bar
0 bar to 6 bar
0 bar to 10 bar
0 psi to 1 psi
0 psi to 5 psi
0 psi to 15 psi
0 psi to 30 psi
0 psi to 60 psi
0 psi to 100 psi
0 psi to 150 psi
DIP Leadless SMT
AN
SMT
LN
PN
Single axial
barbless port
Low-profile
port
Single axial
barbed port
AN
LN
PN
Single axial
barbless port
Low-profile
port
Single axial
barbed port
AN
LN
PN
Single axial
barbless port
Low-profile
port
Single axial
barbed port
Pressure Port
Sensing and Control
Honeywell
1985 Douglas Drive North
Golden Valley, MN 55422
honeywell.com
50076346-F-EN IL50
October 2014
Copyright © 2014 Honeywell International Inc. All rights reserved.
WARRANTY
Honeywell warrants goods of its manufacture as being free of
defective materials and faulty workmanship. Honeywell’s standard
product warranty applies unless agreed to otherwise by Honeywell
in writing; please refer to your order acknowledgement or consult
yourlocalsalesofficeforspecicwarrantydetails.Ifwarranted
goods are returned to Honeywell during the period of coverage,
Honeywell will repair or replace, at its option, without charge those
items it nds defective. The foregoing is buyer’s sole remedy
and is in lieu of all warranties, expressed or implied, including
those of merchantability and tness for a particular purpose.
In no event shall Honeywell be liable for consequential,
special, or indirect damages.
While we provide application assistance personally, through our
literature and the Honeywell web site, it is up to the customer to
determine the suitability of the product in the application.
Specications may change without notice. The information we
supply is believed to be accurate and reliable as of this printing.
However, we assume no responsibility for its use.
WARNING
PERSONAL INJURY
DONOTUSEtheseproductsassafetyoremergencystop
devices or in any other application where failure of the product
could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
SALES AND SERVICE
Honeywell serves its customers through a worldwide network
of sales offices, representatives and distributors. For application
assistance, current specications, pricing or name of the nearest
AuthorizedDistributor,contactyourlocalsalesofficeor:
E-mail:info.sc@honeywell.com
Internet:sensing.honeywell.com
Phone and Fax:
Asia Pacic +65 6355-2828
+65 6445-3033 Fax
Europe +44(0)1698481481
+44 (0) 1698 481676 Fax
LatinAmerica +1-305-805-8188
+1-305-883-8257 Fax
USA/Canada +1-800-537-6945
+1-815-235-6847
+1-815-235-6545 Fax
TBP Series, Compensated/Unamplified
NBP Series, Uncompensated/Unamplified
ISSUE F
50076346
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Honeywell:
TBPMANN060PGUCV TBPDLNN150PGUCV TBPMANS060MGUCV TBPMANN400MGUCV TBPDANN030PGUCV
TBPDLNS030PGUCV TBPLANS030PGUCV TBPDLNN004BGUCV TBPLANS060MGUCV TBPLPNS1.6BGUCV
TBPLANN060PGUCV TBPDANS150PGUCV TBPMANN015PGUCV TBPDANN060PGUCV TBPLPNS005PGUCV
TBPDLNN100PGUCV TBPLPNS400MGUCV TBPDANN250MGUCV TBPDLNN060MGUCV TBPMANS030PGUCV
TBPDLNS150PGUCV TBPDANN015PGUCV