TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 1 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 1.0 OBJECTIVE This specification defines the performance, test, quality and reliability requirements of the USB+Power (Universal Serial Bus with keyed power terminals) including the following: Series "A" Right Angle 2.0 SCOPE: This specification is applicable to the termination characteristics of the USB+ Power family of products, which provides interconnection of computer peripherals. 3.0 GENERAL This document is composed of the following sections: Paragraph 1. 2. 3. 4. 5. 5.1 5.2 5.3 5.4 5.5 6. 7. 8. 9. 9.1 9.2 9.3 9.4 9.5 9.6 Figure 1 Figure 2 Table 1 Title OBJECTIVE SCOPE GENERAL APPLICABLE DOCUMENTS REQUIREMENTS Qualification Product Examination Material Finish Design and Construction ELECTRICAL CHARACTERISTICS MECHANICAL CHARACTERISTICS ENVIRONMENTAL CHARACTERISTICS QUALITY ASSURANCE PROVISIONS Equipment Calibration Inspection Conditions Sample Quantity And Description Acceptance Qualification Testing Re-qualification Testing CONTACT RESISTANCE MEASUREMENT POINTS SHOCK AND VIBRATION MOUNTING FIXTURE QUALIFICATION TESTING AND SEQUENCE MATRIX This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION GS-12-130 (Was GES-12-130) TITLE PAGE USB + Power Product Specification REVISION K 2 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 4.0 APPLICABLE DOCUMENTS 4.1 Specifications: 4.1.1 Engineering Drawings 55917, 57489,10063583 74233, 57496 4.2 4.3 USB + Power Receptacle Assembly USB + Power Plug Assembly Military Standards: 4.2.1 MIL-STD-202F: 4.2.2 MIL-STD-1344A: 4.2.3 MIL-C-45662: Test Methods for Electronic Component Parts Test Methods for Electrical Connectors Equipment Calibration Federal Specifications: 4.3.1 QQ-N-290: 4.3.2 QQ-B-750: 4.3.3 QQ-S-571: Nickel Plating (Electrodeposited) Phosphor Bronze Alloy Strip Solder 4.4 Other Standards and Specifications: 4.4.1 UL94: Flammability 4.4.2 ASTM B-103: Phosphor Bronze 4.4.3 ISO 9000: 4.4.4 EIA 364: Electrical connector/socket test procedures including environmental classifications 4.4.5 ASTM-D-4565: Physical and Environmental Performance Properties of Insulation and Jacket for Telecommunications Wire and Cable, Test Standard Method 4.4.6 ASTM-D-4566: Electrical Performance Properties of Insulation and Jacket for Telecommunication Wire and Cable, Test Standard Method 4.4.7 USB Universal Serial BUS Specification 4.5 Berg Specifications: 4.5.1 BUS-03-114: 4.5.2 BUS-03-404: 4.5.3 BUS-03-405: 4.5.4 BUS-03-601: 4.5.5 BUS-16-016: 4.5.6 BUS-16-074: 4.5.7 BUS-19-002: 4.5.8 BUS-19-020: 4.5.9 BUS-19-040: 4.5.10 BUS-19-002: 4.5.11 BUS-19-122: Capacitance Measurement Normal Force Measurement Insertion/Withdrawal Force Measurement Current Rating/30 Temperature Rise Phosphor Bronze Strip PCT, 30% glass Solderability Porosity Plating Adhesion Surface Mount Solder Joint Reliability Solder Joint Reliability Test Procedure for Surface Mount Connectors This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 3 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 5.0 REQUIREMENTS 5.1 Qualification Connectors furnished under this specification shall be capable of meeting the qualification test requirements specified herein. 5.2 Product Examination Product will be examined per EIA-364-18 verifying visually paragraphs 5.3, 5.4, and 5.5. Dimensional examination is not required. 5.3 Material Material for each part shall be specified herein, or equivalent. Substitute material shall meet the performance requirements of this specification. 5.4 5.3.1 Receptacle and Plug Terminal - The material shall be high strength copper alloy strip. 5.3.2 Receptacle and Plug Insulator Housings and Covers - Connectors shall be molded of plastic that is rated UL94-V-0 or better in accordance with UL-94. 5.3.3 Receptacle and Plug Shell - The base material shall be phosphor-bronze strip. 5.3.4 Insulator housings and covers of lead free part - The insulator housings and covers of lead o free part will withstand exposure to 260 C peak temperature for 40 seconds in a convection, infra-red or vapor phase reflow oven. For 10063583, it also can withstand o exposure to 260 C peak temperature for 10 seconds for 3 times. 5.3.5 Lead free products - All lead free products are RoHS compatible. Finish 5.4.1 5.5 Receptacle and Plug terminals - shall be plated in the contact area with 0,76um (30 inches) palladium nickel with gold flash minimum over 1,27um (50 inches) minimum nickel. The receptacle terminal solder tail sections shall be plated with 2,54um (100 inches) 90/10 tinlead minimum or 2,54um (100 inches) minimum matted tin for lead free part over 1,27um (50 inches) minimum nickel. The terminal areas outside of the contact areas and the solder tail areas shall be plated with 1,27um (50 inches) nickel minimum. 5.4.2 Outside shells - shall be plated with 2, 00um (75inches) minimum 90/10 bright tin-lead over 1,27um (50 inches) minimum nickel underplate or 2, 00um (75inches) minimum bright tin over 1,27um (50 inches) minimum nickel underplate or only 1.27um (50 micro inches) minimum nickel. 5.4.3 Lead free plating - All plating chemical for lead free part are qualified by FCI. FCI qualification include solderability, whiskering, solder joint reliability and tarnishing effects. Design and Construction This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 4 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 6.0 5.5.1 Receptacle connector - is a multiple piece assembly having a lower single row of contacts (USB standard terminals) spaced on dissimilar centerlines (the two inner contacts are spaced 2.0mm apart and the terminals adjacent to these terminals are spaced 2.5mm away) in the interface area. The Upper row of contacts used for power transmission is spaced 2.5mm apart. Each terminal transition will be a 90 degree bend to allow for termination to the PC board by a through hole leg. The outside shell has six resilient contact arms (four on the sides and two on the bottom) that act as ESD grounding as well as cable plug retention features. The two arms on the side of the shell assure that there is constant contact between the shell and the shell of the cable assembly plug while the connectors are mated. The receptacle is has a recess to accommodate the spring latch on the plug connector. The entire receptacle assembly is attached to the printed circuit board via four retention claws on the outside shell. The connector has four keys for various supply voltages. Refer to the Customer Drawing for recommended P.C. Board thickness and keying positions. 5.5.2 The plug connector - is a multiple piece assembly having a lower single row of contacts (USB standard terminals) spaced on dissimilar centerlines (the two inner contacts are spaced 2.0mm apart and the terminals adjacent to these terminals are spaced 2.5mm away) in the interface area. The Upper row of contacts used for power transmission is spaced 2.5mm apart. Each terminal is straight and is soldered to the cable connectors. The connector is fitted with two shells. The front shell when mated with the receptacle is in contact with the resilient contact arms of the receptacle providing EMI protection. The rear shell provides EMI protection as well as clamps to the cable providing a specified cable strain relief pull force. The outside shell has six resilient contact arms (four on the sides and two on the bottom) that act as ESD grounding as well as cable plug retention features. The two arms on the side of the shell assure that there is constant contact between the shell and the shell of the cable assembly plug while the connectors are mated. A plastic spring latch on top of the connector positively latches into the receptacle connector when mated. The connector provides four keying positions for various supply voltages. Refer to the Customer Drawing keying positions. 5.5.3 Mating - The connectors shall be capable of mating and unmating manually without the use of special tools. 5.5.4 Workmanship - Connectors shall be uniform in quality and shall be free from burrs, scratches, cracks, voids, chips, blisters, pin holes, sharp edges, other defects, debris and any ingress of foreign material that will adversely affect life or serviceability. 5.5.5 Temperature Rating - The receptacle connector shall be capable of withstanding a storage temperature range of -55oC to 85oC and an operating temperature range of -55oC to 85oC. ELECTRICAL CHARACTERISTICS 6.1 Low Level Contact Resistance(LLCR) 6.1.1 6.1.2 6.1.3 Test Standard: Acceptance Criteria: Connection Method: EIA 364-23 30m max. Attach current and voltage leads as shown in Figure 1 for p/n 55917, 74233/ Figure 3 for p/n 57489, 57496 This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 5 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 6.2 Insulation Resistance 6.2.1 6.2.2 6.2.3 6.2.4 6.2.5 Test Standard: Acceptance Criteria: Test Voltage: Electrification Time: Measurement Points: EIA 364-21 >1000 megohms, mated and unmated 500 volts DC 2 minutes Between adjacent contacts and between contacts shell This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 6 of 16 AUTHORIZED BY DATE XK ZHANG 07/05/10 CLASSIFICATION UNRESTRICTED 6.3 6.4 6.5 Dielectric Withstanding Voltage 6.3.1 6.3.2 Test Standard: Acceptance Criteria: 6.3.3 6.3.4 Test Voltage: Test Barometric Pressure: Current Rating 6.4.1 6.4.2 6.4.3 Test Standard: Acceptance Criteria: Test Methods: 6.4.4 Ambient Conditions: BUS-03-601 0 30 C Max. delta T any point. USB Section; With all contacts energized 1.5 Amp per contact Power Section; With all contacts energized,3.0 Amps per contact. Note: All contacts to be energized for this test Still air at 25 degrees C. Capacitance 6.5.1 6.5.2 6.5.3 6.5.4 6.5.5 7.0 EIA 364-20, Method A No evidence of arc-over, insulation breakdown, or excessive current leakage(> 1 mA) mated and unmated connectors 750 volts AC, 60 760mm Hg, Sea level Test Standard: Acceptance Criteria: Ambient Conditions: Frequency: Points of Measurement EIA 364-30 2 pF max. Still air at 25 degrees C. 1 kHz (default 1 MHz) Between adjacent contacts in an unmated connector MECHANICAL CHARACTERISTICS 7.1 Mating/Unmating Force 7.1.1 7.1.2 7.1.3 7.1.4 7.2 Test Standard: Acceptance Criteria: 7.1.2.1 Mating: 7.1.2.2 Unmating: Cross Head Speed: Mounting: EIA 364-13 <66.0 N (15 Lb.)per plug <44.0 N (10 Lb.)per plug after latch is unlatched 1 inch per minute Free floating fixtures Contact Retention 7.2.1 7.2.2 7.2.3 Test Standard: Acceptance Criteria: Application Rate: EIA 364-29 Axial Load > 0.5 pounds without dislodging 0.2 inches/minute This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 7 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 7.3 7.4 7.5 8.0 Latch Pull Force 7.3.1 7.3.2 Test Standard: Acceptance Criteria: 7.3.3 Application Rate: EIA 364-13 Mated condition Multi-directional <66.0 N (15 Lb.) without loss of continuity and without causing visible physical damage to the receptacle and plug 0.2 inches/minute Cable Pull Out 7.4.1 7.4.2 Test Standard: Acceptance Criteria: 7.4.3 Application Rate: EIA 364-46 Axial pull without loss of continuity, No jacket tears or visual exposure of shield. No jacket movement greater than 1.5 mm at point of exit Plug Unmated condition Cable Axial-directional <132.0 N (30 Lb.) 0.2 inches/minute Cable Flexing 7.5.1 Test Standard: 7.5.2 7.5.3 Acceptance Criteria: Application Rate: EIA 364-41, Condition I: dim x=3.7 x cable diameter or thickness; 100 cycles in each of two planes No discontinuities, DWV, IR, Mated Condition Cable ENVIRONMENTAL CONDITIONS Acceptance Criteria - After exposure to the following environmental conditions in accordance with the specified test procedure and/or details, the product shall show no physical damage and shall meet the electrical and mechanical requirements per paragraphs 6.0 and 7.0 as specified in the Table 1. Unless specified otherwise, assemblies shall be mated during exposure. 8.1 Thermal Shock 8.1.1 8.1.2 8.1.3 8.1.4 8.2 EIA 364-32, Test Condition I 5 30 minutes 5 minutes maximum Temperature & Humidity 8.2.1 8.2.2 8.2.3 8.3 Test Standard: Number of Cycles: Time at each Temperature: Transfer Time: Test Standard: High Temperature/Humidity: Low Temperature/Humidity Cycle times: As specified below 60+/-3 degrees C @ 90-95 RH 25+/-3 degrees C @ 55 +/- 10% RH 8 hours total 1.75 hours @ Low, 1.5 ramp up, 4 hours @ high, .75 hour ramp down High Temperature Life This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 8 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 8.3.1 8.3.2 8.3.3 8.4 8.8 Test Standard: Acceptance Criteria: Duration: Mounting: EIA 364-28, Test Condition: V ,Test Letter A No discontinuities greater than 1 microsecond 15 minutes along each of three orthogonal axes See Figure 2 for p/n 55917, 74233/ Figure 4 for p/n 57489, 57496 Test Standard: Acceptance Criteria: Mounting: EIA 364-27, Condition: H No discontinuities greater than 1microseconds See Figure 2 8.7.1 Test Standard: 8.7.2 8.7.3 Number of Cycles: Cycling Rate: Standard laboratory procedure as applicable to the specific product, Latch removed 1500 cycles 200 cycles/hour Maximum Durability Solderability 8.8.1 8.8.2 8.8.3 8.9 EIA 364-65, Class: III 7 days Mated connectors Mechanical Shock 8.6.1 8.6.2 8.6.3 8.7 Test Standard: Duration: Condition: Vibration, Random 8.5.1 8.5.2 8.5.3 8.5.4 8.6 EIA 364-17, Test Condition 3, Method A 85 degrees C 250 hours Industrial Mixed Flowing Gas (IMFG) 8.4.1 8.4.2 8.4.3 8.5 Test Standard: Test Temperature: Test Duration: Test Standard: Acceptance Criteria: Steam Aging: ANSI-J-002, Test Condition A Meets ANSI-J-002 requirements 4 hours Resistance to Solder Heat 8.9.1 8.9.2 Test Standard: 8.9.1.1 Thru Hole 8.9.1.2 Surface Mount Acceptance Criteria: EIA 364-56,Procedure 3,Condition E EIA 364-56,Procedure 5, Level 3 There shall be no evidence of physical or mechanical damage This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION GS-12-130 (Was GES-12-130) TITLE PAGE USB + Power Product Specification REVISION K 9 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 8.10 Resistance to Solvents 8.10.1 8.10.2 8.10.3 8.10.4 9.0 Test Standard: Acceptance Criteria: Solvent Temperature: Immersion Time: EIA 364-11, Class IV No evidence of physical or mechanical damage 25 C 3 minutes QUALITY ASSURANCE PROVISIONS 9.1 Equipment Calibration All test equipment and inspection facilities used in the performance of any test shall be maintained in a calibration system in accordance with MIL-C-45662 and ISO 9000. 9.2 Inspection Conditions Unless otherwise specified herein, all inspections shall be performed under the following ambient conditions: 9.2.1 9.2.2 9.2.3 9.3 Temperature: Relative Humidity: Barometric Pressure: 25 +/- 5 degrees C 30% to 60% Local ambient Sample Quantity and Description Total Receptacles: 52 Total Plugs 57 9.3.1 9.3.2 9.3.3 9.3.4 9.3.5 Groups 1, 2 ,7: Groups 3, 5, 6: Group 4: Group 8, 9: Group 10: 8 samples in each group ( 8 receptacles, 8 plugs) 5 samples in each group (5 receptacles, 5 plugs) 3 samples in group ( 3 receptacles, 3 plugs) 5 samples in group ( 5 receptacles, 5 plugs) 5 samples in group ( 5 plugs) Note: Group 3: Receptacle is loose piece and not mounted to the test board 9.4 9.5 Acceptance 9.4.1 Electrical and mechanical requirements placed on test samples as indicated in paragraphs 6.0 and 7.0 shall be established from test data using appropriate statistical techniques or shall otherwise be customer specified, and all samples tested in accordance with this product specification shall meet the stated requirements. 9.4.2 Failures attributed to equipment, test set-up, or operator error shall not disqualify the product. If product failure occurs, corrective action shall be taken and samples resubmitted for qualification. Qualification Testing - Qualification testing shall be performed on sample units produced with equipment and procedures normally used in production. The test sequence shall be as shown in Table 1. This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 10 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED 9.6 Re-qualification Testing - If any of the following conditions occur, the responsible product engineer shall initiate re-qualification testing consisting of all applicable parts of the qualification test matrix (Table 1). 9.6.1 9.6.2 9.6.3 A significant design change is made to the existing product which impacts the product form, fit or function. Examples of significant changes shall include, but not be limited to, changes in the plating material composition or thickness, contact force, contact surface geometry, insulator design, contact base material, or contact lubrication requirements. A significant change is made to the manufacturing process which impacts the product form, fit or function. A significant event occurs during production or end use requiring corrective action to be taken relative to the product design or manufacturing process. This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 11 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:J PDM: Rev:K STATUS:Released Printed: Nov 28, 2010. STATUS: Released Printed: May 06, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 12 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:J PDM: Rev:K STATUS:Released Printed: Nov 28, 2010. STATUS: Released Printed: May 06, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 13 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:J PDM: Rev:K STATUS:Released Printed: Nov 28, 2010. STATUS: Released Printed: May 06, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 14 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:J PDM: Rev:K STATUS:Released Printed: Nov 28, 2010. STATUS: Released Printed: May 06, 2010. TYPE NUMBER PRODUCT SPECIFICATION TITLE GS-12-130 (Was GES-12-130) PAGE USB + Power Product Specification REVISION K 15 of 16 AUTHORIZED BY XK ZHANG DATE 07/05/10 CLASSIFICATION UNRESTRICTED Qualification Testing and Sequence Matrix See paragraph. 9.3 for quantities Test Procedure Para 1 2 3 4 5 6 7 8 9 Product Examination 5.2 1,11 1,7 1,5,11 (C) 1,3 1,3 1,4 1,5 1,3 1,5 Contact Resistance 6.1 3,5,8, 10 2,4,6 2,6 Insulation Resistance 6.2 3,10 (C) 2,6 6.3 4,9 (C) Dielectric Withstanding 3,7 Voltage Current Rating 6.4 2 Capacitance 6.5 2,8 (C) Mating / Unmating Forces 7.1 2,9 Contact Retention 7.2 8 (B) Thermal Shock 8.1 6 3 (D) Temperature and Humidity 8.2 7 5(E) High Temperature Life 8.3 5 Ind. Mixed Flowing Gas 8.4 4 Vibration 8.5 6 Mechanical Shock 8.6 7 Durability 8.7 4 3(A) Solderability 8.8 2 Resistance to Soldering 8.9 2 Heat Resistance to Solvents 8.10 3 Latch Test 7.3 2 Cable Flex Test 7.4 4 Cable Pull Out 7.5 ( A ) Condition samples with 10 cycles of durability ( B ) Testing to be done on loose piece (un-terminated) connector that has been exposed to high temperature life testing ( C ) Loose piece parts used for this testing ( D ) Condition samples with 5 cycles of durability ( E ) Test durability 7 days only 10 1,3 2 Table 1 Qualification Testing and Sequence Matrix This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:J PDM: Rev:K STATUS:Released Printed: Nov 28, 2010. STATUS: Released Printed: May 06, 2010. TYPE NUMBER PRODUCT SPECIFICATION GS-12-130 (Was GES-12-130) TITLE PAGE USB + Power Product Specification REVISION K 16 of 16 AUTHORIZED BY DATE XK ZHANG 07/05/10 CLASSIFICATION UNRESTRICTED REVISION RECORD PAGE DESCRIPTION EC # DATE A All Released V81785 9/29/98 B All Removed group 7 from matrix Renamed groups 8,9,10,11 to 7,8,9,10, Decreased quantity of group 4 from 9 to 3 Paragraph 9.3 Quantities were Total Receptacles 63, Total plugs 68 V82003 11/04/98 C ALL V01739 08/03/00 D ALL V01775 08/28/00 E F G H ALL ALL ALL 3 Para. 7.1 Changed from >44.0 N to < 44.0 N Para 7.1.2 Added without causing visible physical damage to the receptacle. Para 7.3.2 Added without causing visible physical damage to the plug and receptacle. Guardian Site Transfer To Taiwan. Add Figure 3&4 to describe electrical test Update current rating 5.4.1 Add "or 2,54um (100 inches) minimum matted tin for lead free part" T20205 T20276 T04-0101 N04-0072 08/14/02 09/10/02 03/05/04 10/21/04 N04-0072 10/21/04 N04-0072 10/21/04 N04-0072 N04-0072 N06-0234 N06-0234 N10-0120 10/21/04 10/21/04 09/05/06 09/05/06 07/05/10 REV 3 3 J H 3 3 2 3 4 5.4.2 Add "or 2,00um (75 inches) minimum matted tin for lead free part" Add 5.3.4 Insulator housings and covers of lead free part Add 5.4.3 lead free plating Add 5.3.5 lead free part material 4.1.1 Add engineering drawing 10063583 5.4.2 Add plating option: only nickel 5.5.5 Change the storage temperature range from -40oC~~60oC to -55oC~~85oC.And change the operating temperature range from 0oC~~40oC to -55oC~~85oC. This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in any way without the written consent of FCI Electronics. Form E-3005 Rev A 02/12/01 V20603 GS-01-001 PDM: Rev:K Rev:J PDM: STATUS: Released Released Printed: May 06, 2010.. Nov 28, Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: FCI / Amphenol: 55917-501LF 74233-201LF 74233-202LF 55917-600LF 55917-601LF 55917-001LF 10116136-001LF