SYSTEM NO.
SEE CHART OVERMOLDED MDSR-7 DRAWING NO.
D10-59166-1-X-00-X-1
ORIGINAL DCR NO.
L3516 HAMLIN PROPRIETARY NOTE: THE INFORMATION ON THIS DRAWING IS THE CONFIDENTIAL PROPERTY OF HAMLIN. THIS DRAWING MUST NOT
BE MADE PUBLIC OR COPIED UNLESS AUTHORIZED IN WRITING BY HAMLIN. THIS DRAWING IS SUBJECT TO RETURN UPON DEMAND. SHEET
1 of 2 DCR No.
L3516 REV.
AA
DRAWN BY:
KCL DATE:
05-May-08 DESCRIPTION OF REVISION: New Drawing
DRAWN BY:
DATE:
APP’D BY:
HG DATE:
09
-
May
-
08
APP’D BY:
DATE:
PART NUMBER INFORMATION
TABLE 1 TABLE 2 TABLE 3
SERIES -SWITCH TYPE -SENSITIVITY -00 PACKAGING
59166 ___ ___ ___
OVERMOLDED 1 = Normally Open S = 10-15 A = Leaded
MDSR-7 T = 15-20 C = Gull Wing bulk packed
U = 20-25 D = Gull Wing taped and reel (1500 PER REEL)
PART
NUMBER
SYS # EXTENDED DESCRIPTION ACTUATE DIST DEACTUATE DIST
VOLTAGE
BREAKDOWN
CONTACT
RESISTANCE
59166-1-S-00-A 37213 59166 MDSR-7 10-15 LEADED 0.160 MIN 0.480 MAX 150-350 volts 0.100 ohm MAX.
59166-1-S-00-C 37214 59166 MDSR-7 10-15 GW BULK 0.150 MIN 0.380 MAX 150-350 volts 0.100 ohm MAX.
59166-1-S-00-D 37215 59166 MDSR-7 10-15 GW TAPE 0.150 MIN 0.380 MAX 150-350 volts 0.100 ohm MAX.
59166-1-T-00-A 37216 59166 MDSR-7 15-20 LEADED 0.155 MIN 0.460 MAX 150-350 volts 0.100 ohm MAX.
59166-1-T-00-C 37217 59166 MDSR-7 15-20 GW BULK 0.145 MIN 0.370 MAX 150-350 volts 0.100 ohm MAX.
59166-1-T-00-D 37218 59166 MDSR-7 15-20 GW TAPE 0.145 MIN 0.370 MAX 150-350 volts 0.100 ohm MAX.
59166-1-U-00-A 37219 59166 MDSR-7 20-25 LEADED 0.150 MIN 0.440 MAX 150-350 volts 0.100 ohm MAX.
59166-1-U-00-C 37220 59166 MDSR-7 20-25 GW BULK 0.140 MIN 0.360 MAX 150-350 volts 0.100 ohm MAX.
59166-1-U-00-D 37221 59166 MDSR-7 20-25 GW TAPE 0.140 MIN 0.360 MAX 150-350 volts 0.100 ohm MAX.
STD 57045
ACTUATOR
D
Note for Testing: When testing, probe the sensors in a location where the
terminals will not get bent during or after test. Bent terminals are not acceptable.
SYSTEM NO.
SEE CHART OVERMOLDED MDSR-7 DRAWING NO.
D10-59166-1-X-00-X-1
ORIGINAL DCR NO.
L3516 HAMLIN PROPRIETARY NOTE: THE INFORMATION ON THIS DRAWING IS THE CONFIDENTIAL PROPERTY OF HAMLIN. THIS DRAWING MUST NOT
BE MADE PUBLIC OR COPIED UNLESS AUTHORIZED IN WRITING BY HAMLIN. THIS DRAWING IS SUBJECT TO RETURN UPON DEMAND. SHEET
2 of 2 DCR No.
L3516 REV.
AA
DRAWN BY:
KCL DATE:
05-May-08 DESCRIPTION OF REVISION: New Drawing
DRAWN BY:
DATE:
APP’D BY:
HG DATE:
09
-
May
-
08
APP’D BY:
DATE:
0.018 [0.47]
0.045 [1.14]
.000 to .005
[0.000 to 0.127]
NOTE: PADS NOT TO EXTEND
BELOW THE SENSOR BODY PLANE.
5°
10° MAX
L
CLEAD
LEAD
C
L
*
0.030 [7.62]. 2 places.
DIMENSIONS ARE "AFTER TEST" INCHES [mm]
TOLERANCES: UNLESS NOTED OTHERWISE
.XX: ± .010
.XXX: ±.005
ANGULAR: ±1/2°
.095 [2.40]
.095 [2.40]
.099 [2.51]
C BULK
D TAPE & REEL
.630 [16.00] MAX
59165-1-X-00-X XXXX
.795 [20.20]
.670 [17.01]
59165 - 1 - - 00 -
SENSITIVITY (S,T,U)
TERMINATION (A,C,D)
ELECTRICAL RATINGS
CONTACT FORM A
CONTACT RATING WATTS 10
VOLTAGE SWITCHING VDC-MAX 200
BREAKDOWN VDC-MIN 250
ARC - QUENCH VDC-MIN 200
CURRENT SWITCHING AMPS-MAX 0.5
CARRY AMPS-MAX 0.8
RESISTANCE INITIAL CONTACT
OHMS-MAX 0.1
INSULATION OHMS-MIN 10
12
CAPACITANCE
PICOFARADS-TYP 0.3
OPERATING CHARACTERISTICS
OPERATE TIME
ms-MAX 0.6
RELEASE TIME
ms-MAX 0.2
SHOCK
G's MAX, 11ms 1/2 SINE WAVE 100
VIBRATION
G's MAX, 50-2000 HERTZ 30
RESONANT FREQUENCY HERTZ, TYPICAL 5500
TEMPERATURE OPERATING
DEGREES CELCIUS -40 to +125
STORAGE
DEGREES CELCIUS -65 to +125
REFLOW (15 SEC)
MAX
DEGREES CELCIUS 260
0.035 [.89]. 2 places.
.095 [2.40]
.099 [2.51]
.630 [16.00] MAX
.670 [17.01]
1.590 [40.39] A
TERMINATION (A,C,D)
SENSITIVITY (S,T,U)
59166 - 1 - - 00 -
59166-1-X-00-X XXXX
D TAPE & REEL
C BULK
.095 [2.40]
59166-1-X-00-A XXXX
0.630 [16.00] MAX Ø.0185 [0.47]
.095 [2.40]
.095 [2.40]
DIMENSIONS ARE "AFTER TEST" INCHES [mm]
TOLERANCES: UNLESS NOTED OTHERWISE
.XX: ± .010
.XXX: ±.005
ANGULAR: ±1/2°
*
L
CLEAD
LEAD
C
L
10° MAX 5°
NOTE: PADS NOT TO EXTEND
BELOW THE SENSOR BODY PLANE.
.000 to .005
[0.000 to 0.127]
0.018 [0.47]
0.035 [.89]
.805 [20.45]
.079 [2.00]
TAPE DETAILS
(Tek Pak)
.065 [1.65]
.315 [8.00]
1.260 [32.00]
.092 [2.34]
.157 [4.00]
.84 [21.34]
