SYSTEM NO. DRAWING NO. OVERMOLDED MDSR-7 SEE CHART PART NUMBER 59166-1-S-00-A D10-59166-1-X-00-X-1 0.480 MAX VOLTAGE BREAKDOWN 150-350 volts CONTACT RESISTANCE 0.100 ohm MAX. 0.150 MIN 0.380 MAX 150-350 volts 0.100 ohm MAX. 0.150 MIN 0.380 MAX 150-350 volts 0.100 ohm MAX. 0.155 MIN 0.460 MAX 150-350 volts 0.100 ohm MAX. 0.145 MIN 0.370 MAX 150-350 volts 0.100 ohm MAX. 0.145 MIN 0.370 MAX 150-350 volts 0.100 ohm MAX. 59166 MDSR-7 20-25 LEADED 0.150 MIN 0.440 MAX 150-350 volts 0.100 ohm MAX. 37220 59166 MDSR-7 20-25 GW BULK 0.140 MIN 0.360 MAX 150-350 volts 0.100 ohm MAX. 37221 59166 MDSR-7 20-25 GW TAPE 0.140 MIN 0.360 MAX 150-350 volts 0.100 ohm MAX. SYS # EXTENDED DESCRIPTION ACTUATE DIST DEACTUATE DIST 37213 59166 MDSR-7 10-15 LEADED 0.160 MIN 59166-1-S-00-C 37214 59166 MDSR-7 10-15 GW BULK 59166-1-S-00-D 37215 59166 MDSR-7 10-15 GW TAPE 59166-1-T-00-A 37216 59166 MDSR-7 15-20 LEADED 59166-1-T-00-C 37217 59166 MDSR-7 15-20 GW BULK 59166-1-T-00-D 37218 59166 MDSR-7 15-20 GW TAPE 59166-1-U-00-A 37219 59166-1-U-00-C 59166-1-U-00-D PART NUMBER INFORMATION SERIES 59166 OVERMOLDED MDSR-7 TABLE 1 -SWITCH TYPE ___ TABLE 2 -SENSITIVITY ___ 1 = Normally Open S = 10-15 T = 15-20 U = 20-25 -00 TABLE 3 PACKAGING ___ A = Leaded C = Gull Wing bulk packed D = Gull Wing taped and reel (1500 PER REEL) STD 57045 ACTUATOR D Note for Testing: When testing, probe the sensors in a location where the terminals will not get bent during or after test. Bent terminals are not acceptable. ORIGINAL DCR NO. L3516 DRAWN BY: KCL APP'D BY: HG DATE: 05-May-08 DATE: 09-May-08 HAMLIN PROPRIETARY NOTE: THE INFORMATION ON THIS DRAWING IS THE CONFIDENTIAL PROPERTY OF HAMLIN. THIS DRAWING MUST NOT SHEET BE MADE PUBLIC OR COPIED UNLESS AUTHORIZED IN WRITING BY HAMLIN. THIS DRAWING IS SUBJECT TO RETURN UPON DEMAND. DESCRIPTION OF REVISION: New Drawing 1 of 2 DCR No. L3516 DRAWN BY: DATE: APP'D BY: DATE: REV. AA SYSTEM NO. DRAWING NO. OVERMOLDED MDSR-7 SEE CHART D10-59166-1-X-00-X-1 ELECTRICAL RATINGS CONTACT FORM .095 [2.40] A CONTACT RATING .000 to .005 59166-1-X-00-A WATTS 10 [0.000 to 0.127] XXXX VOLTAGE SWITCHING VDC-MAX NOTE: PADS NOT TO EXTEND BELOW THE SENSOR BODY PLANE. .095 [2.40] 0.630 [16.00] MAX C LEAD CURRENT L O.0185 [0.47] 5* RESISTANCE 10 MAX 1.590 [40.39] A C LEAD L 200 BREAKDOWN VDC-MIN 250 ARC - QUENCH VDC-MIN 200 SWITCHING AMPS-MAX CARRY 0.018 [0.47] AMPS-MAX 0.5 0.8 .095 [2.40] 59165-1-X-00-X XXXX INITIAL CONTACT OHMS-MAX INSULATION 10 CAPACITANCE .630 [16.00] MAX PICOFARADS-TYP .099 [2.51] OPERATING CHARACTERISTICS .670 [17.01] .795 [20.20] RELEASE TIME ms-MAX 0.030 [7.62]. 2 places. DIMENSIONS ARE "AFTER TEST" INCHES [mm] TOLERANCES: UNLESS NOTED OTHERWISEG's .XX: .010 VIBRATION .XXX: .005 G's ANGULAR: 1/2 RESONANT FREQUENCY TEMPERATURE C LEAD L 10 MAX 5* 12 0.3 C BULK D TAPE & REEL ms-MAX SHOCK NOTE: PADS NOT TO EXTEND BELOW THE SENSOR BODY PLANE. 0.1 OHMS-MIN .095 [2.40] OPERATE TIME .000 to .005 [0.000 to 0.127] 0.045 [1.14] 0.6 0.2 MAX, 11ms59165 1/2 SINE - 1WAVE - - 00 - 100 MAX, 50-2000 HERTZ SENSITIVITY (S,T,U) 30 TERMINATION (A,C,D) HERTZ, TYPICAL 5500 OPERATING DEGREES CELCIUS -40 to +125 STORAGE DEGREES CELCIUS -65 to +125 REFLOW (15 SEC) DEGREES CELCIUS MAX 260 0.018 [0.47] 59166-1-X-00-X .095 [2.40] XXXX 0.035 [.89] TAPE DETAILS (Tek Pak) C LEAD L .095 [2.40] .630 [16.00] MAX .099 [2.51] .315 [8.00] C BULK .157 [4.00] .670 [17.01] 0.035 [.89]. 2 places. D TAPE & REEL .079 [2.00] 1.260 [32.00] .805 [20.45] DIMENSIONS ARE "AFTER TEST" INCHES [mm] TOLERANCES: UNLESS NOTED OTHERWISE .XX: .010 .XXX: .005 ANGULAR: 1/2 ORIGINAL DCR NO. L3516 DRAWN BY: KCL APP'D BY: HG DATE: 05-May-08 DATE: 09-May-08 HAMLIN 59166 - 1 SENSITIVITY (S,T,U) TERMINATION (A,C,D) - 00 - .092 [2.34] .065 [1.65] .84 [21.34] PROPRIETARY NOTE: THE INFORMATION ON THIS DRAWING IS THE CONFIDENTIAL PROPERTY OF HAMLIN. THIS DRAWING MUST NOT SHEET BE MADE PUBLIC OR COPIED UNLESS AUTHORIZED IN WRITING BY HAMLIN. THIS DRAWING IS SUBJECT TO RETURN UPON DEMAND. DESCRIPTION OF REVISION: New Drawing 2 of 2 DCR No. L3516 DRAWN BY: DATE: APP'D BY: DATE: REV. AA