FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & HIGH VOLTAGE KAMAYA OHM RVC 1. Higher Limiting Element Voltage compared with RMC (general use) 2. Stability Class : 5% W L c c d d Rated resistance is marked with 3-digit (E24) or 4-digit (E96) on the over coating. RVC16 : only 3digit marking is available. H Chip Resistors Unit : mm Metric 1608 2012 3216 5025 6332 Inch 0603 0805 1206 2010 2512 L 1.60.1 2.00.1 3.20.15 5.00.15 6.30.15 W 0.8 0.15 0.05 1.250.10 1.6 0.15 2.5 0.15 3.2 0.15 H 0.450.10 0.550.10 0.550.10 0.550.15 0.550.15 c 0.3 0.1 0.4 0.2 0.5 0.25 0.6 0.2 0.6 0.2 d 0.3 0.1 0.4 0.2 0.5 0.25 0.6 0.2 0.6 0.2 *Unit weight/pc. 2mg 5mg 9mg 25mg 40mg *Values for reference Example Style RVC 32 Product Type Code 16 20 32 50 63 8 Size Metric Inch 1608 0603 2012 0805 3216 1206 5025 2010 6332 2512 K 475 Rated Resistance E24 Series e.g. : 475=4.7M ohm 3-Digit E96 Series e.g. : 7154=7.15M ohm 4-Digit Temperature Coefficient of Resistance - Standard K 10010-6/C F TP * Packaging & Standard Qty. (Min.) Tolerance on Rated Resistance F G J K 1% 2% 5% 10% B TP Bulk (Loose Package) 1,000pcs. All Styles Paper Tape 5,000pcs. RVC16 RVC20 RVC32 4,000pcs. RVC50 RVC63 TE Embossed Tape *Refer to Tape and Packaging information on pages 46 and 47. Product specifications contained in this catalogue are subject to change at any time without notice. Please confirm specifications with your order. KAMAYA OHM Style Size Metric (Inch) RVC16 1608 (0603) 0.1 200 RVC20 2012 (0805) 0.125 400 RVC32 3216 (1206) 0.25 RVC Rated Dissipation Limiting Element Combinations of Rated Resistance Range and Tolerance on Rated Resistance Temperature Coefficient Preferred Number Isolation Category Temperature of Resistance at 70C Voltage Series for Voltage Range F(1%) , G(2%) J(5%) , K(10%) W V Resistors V C Code 10-6/C 470 10M 47 464 10051M 10010M 47 97.6 10010M 10051M 47 97.6 47020M 47051M 47 464 56051M 56020M 100 549 47 97.6 500 RVC50 5025 (2010) 0.5 RVC63 6332 (2512) 1.0 800 K K K K K 100 200 100 200 100 200 100 200 100 200 500200 100 F(1%) G(2%) E96 E24 55125 500 J( 5%) K(10%) E24 Note1. Rated Voltage = (Rated Dissipation)(Rated Resistance). (d.c. or a.c. r.m.s. Voltage) Note2. Limiting Element Voltage can only be applied to resistors when the resistance value is equal to or higher than the critical resistance value. Note3. Critical Resistance Value is the resistance value at which the rated voltage is equal to the limiting element voltage. The derated values of dissipation for temperatures in excess of 70C shall be indicated by the following Curve. ! 100 Percentage of the rated dissipation(%) " 55/125/56 Lower Category Temperature Upper Category Temperature Duration of the Damp heat, Steady-State Test -55C +125C 56 days Area of recommended operation 0 55 70 0 125 Ambient Temperature (C) Description Requirements Test Methods Voltage proof No breakdown or flashover R1G ohm Clause 4.7 RVC16 RVC20~RVC63 Variation of resistance with temperature See Ratings Table Clause 4.8 Measuring temperature :+20C/-55C/+20C/+125C/+20C Overload DR(1%+0.05 ohm) Clause 4.13 The applied voltage shall be 2.5 times of the rated voltage or twice of the limiting element voltage, whichever is the less severe, 2s. Clause 4.17 235C, 2s Clause 4.18 After immersion into the flux, the immersion into solder shall be carried out in Solder bath at 260C for 5s. Solderability Resistance to soldering heat Rapid change of temperature No visible damage, legible marking In accordance with Clause 4.17.4.5 DR(1%+0.05 ohm) DR(1%+0.05 ohm) No visible damage 100Va.c.,60s 500Va.c.,60s Clause 4.19 5 cycles between -55C and +125C. Climatic sequence DR(5%+0.1 ohm) No visible damage Damp test, steady state Endurance at 70C Endurance at the upper category temperature Adhesion Bend strength of the face plating DR(5%+0.1 ohm) No visible damage, legible marking DR(5%+0.1 ohm) No visible damage Clause 4.23 Dry/Damp heat(12+12h cycle), first cycle./ Cold/Damp heat(12+12h cycle), remaining cycle. /D.C.Load. Clause 4.24 40C, 95%R.H., 56 days, test a) and b) of Clause 4.24.2.1 Clause 4.25.1 Rated voltage, 1.5h"ON", 0.5h"OFF", 70C, 1,000h. DR(5%+0.1 ohm) No visible damage Clause 4.25.3 125C, no-load, 1,000h. No visible damage Clause 4.32 5N, 10s Clause 4.33 RVC16~RVC32 Amount of bend : 3 mm RVC50, 63 Amount of bend : 1 mm DR(1%+0.05 ohm) Product specifications contained in this catalogue are subject to change at any time without notice. Please confirm specifications with your order. 9 Chip Resistors FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & HIGH VOLTAGE