DAC081S101CIMK - Texas Instruments High-Performance Analog

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

DAC081S101 8-Bit Micro Power Digital-to-Analog Converter with Rail-to-Rail Output

Check for Samples: DAC081S101

1FEATURES DESCRIPTION

The DAC081S101 is a full-featured, general purpose

23• Guaranteed Monotonicity 8-bit voltage-output digital-to-analog converter (DAC)

• Low Power Operation that can operate from a single +2.7V to 5.5V supply

• Rail-to-Rail Voltage Output and consumes just 175 µA of current at 3.6 Volts.

The on-chip output amplifier allows rail-to-rail output

• Power-on Reset to Zero Volts Output swing and the three wire serial interface operates at

• SYNC Interrupt Facility clock rates up to 30 MHz over the specified supply

• Wide Power Supply Range (+2.7V to +5.5V) voltage range and is compatible with standard SPI™,

QSPI, MICROWIRE and DSP interfaces. Competitive

• Small Packages devices are limited to 20 MHz clock rates at supply

• Power Down Feature voltages in the 2.7V to 3.6V range.

The supply voltage for the DAC081S101 serves as its

APPLICATIONS voltage reference, providing the widest possible

• Battery-Powered Instruments output dynamic range. A power-on reset circuit

• Digital Gain and Offset Adjustment ensures that the DAC output powers up to zero volts

and remains there until there is a valid write to the

• Programmable Voltage & Current Sources device. A power-down feature reduces power

• Programmable Attenuators consumption to less than a microWatt.

The low power consumption and small packages of

the DAC081S101 make it an excellent choice for use

in battery operated equipment.

The DAC081S101 is a direct replacement for the

AD5300 and is one of a family of pin compatible

DACs, including the 10-bit DAC101S101 and the 12-

bit DAC121S101. The DAC081S101 operates over

the extended industrial temperature range of −40°C

to +105°C.

Table 1. Key Specifications

VALUE

Resolution 8 bits

DNL +0.04, -0.02 LSB (typ)

Output Settling Time 3 µs (typ)

Zero Code Error 3.8mV (typ)

Full-Scale Error −0.07 %FS (typ)

Normal Mode 0.63 mW (3.6V) / 1.41 mW (5.5V) typ

Power Consumption Pwr Down Mode 0.14 µW (3.6V) / 0.33 µW (5.5V) typ

1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2SPI is a trademark of Motorola, Inc..

3All other trademarks are the property of their respective owners.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

POWER-ON

RESET

DAC

INPUT

CONTROL

LOGIC

8-BIT DAC

POWER-DOWN

CONTROL

LOGIC

BUFFER

1k 100k

SCLK DIN

SYNC

REF(+) REF(-)

VAGND

DAC081S101

VOUT

DIN

SCLK

GND

VOUT 1

SYNC

GND

DIN

SCLK

VOUT SYNC

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

Pin Configuration SOT VSSOP

Block Diagram

Pin Descriptions

SOT-23 VSSOP

Name Description

Pin No. Pin No.

VOUT 1 4 DAC Analog Output Voltage.

GND 2 8 Ground reference for all on-chip circuitry.

VA3 1 Power supply and Reference input. Should be decoupled to GND.

Serial Data Input. Data is clocked into the 16-bit shift register on the falling

DIN 4 7 edges of SCLK after the fall of SYNC.

Serial Clock Input. Data is clocked into the input shift register on the falling

SCLK 5 6 edges of this pin.

Frame synchronization input for the data input. When this pin goes low, it

enables the input shift register and data is transferred on the falling edges

SYNC 6 5 of SCLK. The DAC is updated on the 16th clock cycle unless SYNC is

brought high before the 16th clock, in which case the rising edge of SYNC

acts as an interrupt and the write sequence is ignored by the DAC.

NC 2, 3 No Connect. There is no internal connection to these pins.

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

Product Folder Links: DAC081S101

I/O

GND

TO INTERNAL

CIRCUITRY

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Absolute Maximum Ratings (1)(2)

Supply Voltage, VA6.5V

Voltage on any Input Pin −0.3V to (VA+ 0.3V)

Input Current at Any Pin(3) 10 mA

Package Input Current(3) 20 mA

Power Consumption at TA= 25°C See(4)

ESD Susceptibility(5)

Human Body Model 2500V

Machine Model 250V

Soldering Temperature, Infrared,

10 Seconds (6) 235°C

Storage Temperature −65°C to +150°C

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see

the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics

may degrade when the device is not operated under the listed test conditions.

(2) All voltages are measured with respect to GND = 0V, unless otherwise specified

(3) When the input voltage at any pin exceeds the power supplies (that is, less than GND, or greater than VA), the current at that pin should

be limited to 10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power

supplies with an input current of 10 mA to two.

(4) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by

TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula

PDMAX = (TJmax −TA) / θJA. The values for maximum power dissipation will be reached only when the device is operated in a severe

fault condition (e.g., when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed).

Obviously, such conditions should always be avoided.

(5) Human body model is 100 pF capacitor discharged through a 1.5 kΩresistor. Machine model is 220 pF discharged through ZERO

Ohms.

(6) See the section entitled "Surface Mount" found in any post 1986 National Semiconductor Linear Data Book for methods of soldering

surface mount devices.

Operating Ratings (1)(2)

Operating Temperature Range −40°C ≤TA≤+105°C

Supply Voltage, VA(3) +2.7V to 5.5V

Any Input Voltage(4) −0.1 V to (VA+ 0.1 V)

Output Load 0 to 1500 pF

SCLK Frequency Up to 30 MHz

(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for

which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see

the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics

may degrade when the device is not operated under the listed test conditions.

(2) All voltages are measured with respect to GND = 0V, unless otherwise specified

(3) To guarantee accuracy, it is required that VAbe well bypassed.

(4) The analog inputs are protected as shown below. Input voltage magnitudes up to VA+ 300 mV or to 300 mV below GND will not

damage this device. However, errors in the conversion result can occur if any input goes above VAor below GND by more than 100 mV.

For example, if VAis 2.7VDC, ensure that −100mV ≤input voltages ≤2.8VDC to ensure accurate conversions.

Package Thermal Resistances

Package θJA

8-Lead VSSOP 240°C/W

6-Lead SOT 250°C/W

Product Folder Links: DAC081S101

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

Electrical Characteristics

Values shown in this table are design targets and are subject to change before product release.

The following specifications apply for VA= +2.7V to +5.5V, RL= 2kΩto GND, CL= 200 pF to GND, fSCLK = 30 MHz, input

code range 4 to 251. Boldface limits apply for TMIN ≤TA≤TMAX: all other limits TA= 25°C, unless otherwise specified.

Units

Parameter Test Conditions Typical (1) Limits (1) (Limits)

STATIC PERFORMANCE

Resolution 8Bits (min)

Monotonicity 8Bits (min)

INL Integral Non-Linearity +0.16 +0.75 LSB (max)

−0.12 −0.75 LSB (min)

+0.04 +0.1 LSB (max)

DNL Differential Non-Linearity −0.02 −0.1 LSB (min)

ZE Zero Code Error IOUT = 0 +3.8 +15 mV (max)

FSE Full-Scale Error IOUT = 0 −0.07 −1.0 %FSR (max)

GE Gain Error All ones Loaded to DAC register −0.10 ±1.0 %FSR (max)

ZCED Zero Code Error Drift −20 µV/°C

VA= 3V −0.7 ppm/°C

TC GE Gain Error Tempco VA= 5V −1.0 ppm/°C

OUTPUT CHARACTERISTICS

0V (min)

Output Voltage Range (2) VAV (max)

VA= 3V, IOUT = 10 µA 2.0 mV

VA= 3V, IOUT = 100 µA 5.0 mV

ZCO Zero Code Output VA= 5V, IOUT = 10 µA 3.0 mV

VA= 5V, IOUT = 100 µA 5.4 mV

VA= 3V, IOUT = 10 µA 2.986 V

VA= 3V, IOUT = 100 µA 2.976 V

FSO Full Scale Output VA= 5V, IOUT = 10 µA 4.976 V

VA= 5V, IOUT = 100 µA 4.970 V

RL=∞1500 pF

Maximum Load Capacitance RL= 2kΩ1500 pF

DC Output Impedance 1.3 Ohm

VA= 5V, VOUT = 0V, −63 mA

Input code = FFh

VA= 3V, VOUT = 0V, −50 mA

Input code = FFh

IOS Output Short Circuit Current VA= 5V, VOUT = 5V, 74 mA

Input code = 00h

VA= 3V, VOUT = 3V, 53 mA

Input code = 00h

(1) Typical figures are at TJ= 25°C, and represent most likely parametric norms. Test limits are guaranteed to TI's AOQL (Average

Outgoing Quality Level).

(2) This parameter is guaranteed by design and/or characterization and is not tested in production.

Product Folder Links: DAC081S101

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Electrical Characteristics (continued)

Values shown in this table are design targets and are subject to change before product release.

The following specifications apply for VA= +2.7V to +5.5V, RL= 2kΩto GND, CL= 200 pF to GND, fSCLK = 30 MHz, input

code range 4 to 251. Boldface limits apply for TMIN ≤TA≤TMAX: all other limits TA= 25°C, unless otherwise specified.

Units

Parameter Test Conditions Typical (1) Limits (1) (Limits)

LOGIC INPUT

IIN Input Current(3) ±1 µA (max)

VA= 5V 0.8 V (max)

VIL Input Low Voltage(3) VA= 3V 0.5 V (max)

VA= 5V 2.4 V (min)

VIH Input High Voltage(3) VA= 3V 2.1 V (min)

CIN Input Capacitance(3) 3pF (max)

POWER REQUIREMENTS

VA= 5.5V 256 328 µA (max)

Normal Mode

fSCLK = 30 MHz VA= 3.6V 174 224 µA (max)

VA= 5.5V 221 294 µA (max)

Normal Mode

fSCLK = 20 MHz VA= 3.6V 154 200 µA (max)

VA= 5.0V 142 µA (max)

Normal Mode

fSCLK = 0 VA= 3.0V 107 µA (max)

IASupply Current (output unloaded) VA= 5.0V 83 µA (max)

All PD Modes,

fSCLK = 30 MHz VA= 3.0V 42 µA (max)

VA= 5.0V 56 µA (max)

All PD Modes,

fSCLK = 20 MHz VA= 3.0V 28 µA (max)

VA= 5.5V 0.06 1.0 µA (max)

All PD Modes,

fSCLK = 0 (3) VA= 3.6V 0.04 1.0 µA (max)

VA= 5.5V 1.41 1.80 mW (max)

Normal Mode

fSCLK = 30 MHz VA= 3.6V 0.63 0.81 mW (max)

VA= 5.5V 1.22 1.62 mW (max)

Normal Mode

fSCLK = 20 MHz VA= 3.6V 0.55 0.72 mW (max)

VA= 5.0V 0.71 µW (max)

Normal Mode

fSCLK = 0 VA= 3.0V 0.32 µW (max)

Power Consumption (output

PCunloaded) VA= 5.0V 0.42 µW (max)

All PD Modes,

fSCLK = 30 MHz VA= 3.0V 0.13 µW (max)

VA= 5.0V 0.28 µW (max)

All PD Modes,

fSCLK = 20 MHz VA= 3.0V 0.08 µW (max)

VA= 5.5V 0.33 5.5 µW (max)

All PD Modes,

fSCLK = 0 (3) VA= 3.6V 0.14 3.6 µW (max)

VA= 5V 91 %

IOUT / IAPower Efficiency ILOAD = 2mA VA= 3V 94 %

(3) This parameter is guaranteed by design and/or characterization and is not tested in production.

Product Folder Links: DAC081S101

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

AC and Timing Characteristics

Values shown in this table are design targets and are subject to change before product release.

The following specifications apply for VA= +2.7V to +5.5V, RL= 2kΩto GND, CL= 200 pF to GND, fSCLK = 30 MHz, input

code range 4 to 251. Boldface limits apply for TMIN ≤TA≤TMAX: all other limits TA= 25°C, unless otherwise specified.

Units

Parameter Test Conditions Typical Limits (Limits)

fSCLK SCLK Frequency 30 MHz (max)

Output Voltage Settling Time 40h to C0h code

tsCL≤200 pF 3 5µs (max)

(1) change, RL= 2kΩ

SR Output Slew Rate 1 V/µs

Glitch Impulse Code change from 80h to 7Fh 12 nV-sec

Digital Feedthrough 0.5 nV-sec

VA= 5V 6 µs

tWU Wake-Up Time VA= 3V 39 µs

1/fSCLK SCLK Cycle Time 33 ns (min)

tHSCLK High time 5 13 ns (min)

tLSCLK Low Time 5 13 ns (min)

Set-up Time SYNC to SCLK Rising

tSUCL −15 0ns (min)

Edge

tSUD Data Set-Up Time 2.5 5ns (min)

tDHD Data Hold Time 2.5 4.5 ns (min)

VA= 5V 0 3ns (min)

tCS SCLK fall to rise of SYNC VA= 3V −21ns (min)

2.7 ≤VA≤3.6 9 20 ns (min)

tSYNC SYNC High Time 3.6 ≤VA≤5.5 5 10 ns (min)

(1) This parameter is guaranteed by design and/or characterization and is not tested in production.

Specification Definitions

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1

LSB, which is VREF / 256 = VA/ 256.

DIGITAL FEEDTHROUGH is a measure of the energy injected into the analog output of the DAC from the digital

inputs when the DAC outputs are not updated. It is measured with a full-scale code change on the data bus.

FULL-SCALE ERROR is the difference between the actual output voltage with a full scale code (FFh) loaded

into the DAC and the value of VAx 255 / 256.

GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Zero and

Full-Scale Errors as GE = FSE - ZE, where GE is Gain error, FSE is Full-Scale Error and ZE is Zero Error.

GLITCH IMPULSE is the energy injected into the analog output when the input code to the DAC register

changes. It is specified as the area of the glitch in nanovolt-seconds.

INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a straight line

through the input to output transfer function. The deviation of any given code from this straight line is measured

from the center of that code value. The end point method is used. INL for this product is specified over a limited

range, per the Electrical Tables.

LEAST SIGNIFICANT BIT (LSB) is the bit that has the smallest value or weight of all bits in a word. This value is

LSB = VREF / 2n(1)

where VREF is the supply voltage for this product, and "n" is the DAC resolution in bits, which is 8 for the

DAC081S101.

MAXIMUM LOAD CAPACITANCE is the maximum capacitance that can be driven by the DAC with output

stability maintained.

Product Folder Links: DAC081S101

DB15 DB0

SCLK

DIN

SYNC

tSYNC tSUCL

tSUD

tDHD

tLtHtCS

|||

1 2 13 14 15 16

fCLK

OUTPUT

VOLTAGE

DIGITAL INPUT CODE

00 255

FSE

GE = FSE - ZE

FSE = GE + ZE

255 x VA

256

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

MONOTONICITY is the condition of being monotonic, where the DAC has an output that never decreases when

the output code increases.

MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is

1/2 of VA.

POWER EFFICIENCY is the ratio of the output current to the total supply current. The output current comes from

the power supply. The difference between the supply and output currents, is the power consumed by the device

without a load.

SETTLING TIME is the time for the output to settle within 1/2 LSB of the final value after the input code is

updated.

WAKE-UP TIME is the time for the output to settle to within 1/2 LSB of the final value after the device is

commanded to the active mode from any of the power down modes.

ZERO CODE ERROR is the output error, or voltage, present at the DAC output after a code of 00h has been

entered.

Transfer Characteristic

Figure 1. Input / Output Transfer Characteristic

Timing Diagram

Figure 2. DAC081S101 Timing

Product Folder Links: DAC081S101

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

Typical Performance Characteristics

fSCLK = 30 MHz, TA= 25C, Input Code Range 4 to 251, unless otherwise stated

DNL at VA= 3.0V DNL at VA= 5.0V

Figure 3. Figure 4.

INL at VA= 3.0V INL at VA= 5.0V

Figure 5. Figure 6.

TUE at VA= 3.0V TUE at VA= 5.0V

Figure 7. Figure 8.

Product Folder Links: DAC081S101

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Typical Performance Characteristics (continued)

fSCLK = 30 MHz, TA= 25C, Input Code Range 4 to 251, unless otherwise stated

DNL INL

vs. vs.

VAVA

Figure 9. Figure 10.

3V DNL 5V DNL

vs. vs.

fSCLK fSCLK

Figure 11. Figure 12.

3V DNL 5V DNL

vs. vs.

Clock Duty Cycle Clock Duty Cycle

Figure 13. Figure 14.

Product Folder Links: DAC081S101

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

Typical Performance Characteristics (continued)

fSCLK = 30 MHz, TA= 25C, Input Code Range 4 to 251, unless otherwise stated

3V DNL 5V DNL

vs. vs.

Temperature Temperature

Figure 15. Figure 16.

3V INL 5V INL

vs. vs.

fSCLK fSCLK

Figure 17. Figure 18.

3V INL 5V INL

vs. vs.

Clock Duty Cycle Clock Duty Cycle

Figure 19. Figure 20.

Product Folder Links: DAC081S101

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Typical Performance Characteristics (continued)

fSCLK = 30 MHz, TA= 25C, Input Code Range 4 to 251, unless otherwise stated

3V INL 5V INL

vs. vs.

Temperature Temperature

Figure 21. Figure 22.

Zero Code Error Zero Code Error

vs. vs.

fSCLK Clock Duty Cycle

Figure 23. Figure 24.

Zero Code Error Full-Scale Error

vs. vs.

Temperature fSCLK

Figure 25. Figure 26.

Product Folder Links: DAC081S101

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

Typical Performance Characteristics (continued)

fSCLK = 30 MHz, TA= 25C, Input Code Range 4 to 251, unless otherwise stated

Full-Scale Error Full-Scale Error

vs. vs.

Clock Duty Cycle Temperature

Figure 27. Figure 28.

Supply Current Supply Current

vs. vs.

VATemperature

Figure 29. Figure 30.

5V Glitch Response Power-On Reset

Figure 31. Figure 32.

Product Folder Links: DAC081S101

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Typical Performance Characteristics (continued)

fSCLK = 30 MHz, TA= 25C, Input Code Range 4 to 251, unless otherwise stated

3V Wake-Up Time 5V Wake-Up Time

Figure 33. Figure 34.

Product Folder Links: DAC081S101

To Output Amplifier

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

FUNCTIONAL DESCRIPTION

DAC SECTION

The DAC081S101 is fabricated on a CMOS process with an architecture that consists of switches and a resistor

string that are followed by an output buffer. The power supply serves as the reference voltage. The input coding

is straight binary with an ideal output voltage of:

VOUT = VAx (D / 256) (2)

where Dis the decimal equivalent of the binary code that is loaded into the DAC register and can take on any

value between 0 and 255.

RESISTOR STRING

The resistor string is shown in Figure 35. This string consists of 4096 equal valued resistors with a switch at each

junction of two resistors, plus a switch to ground. The code loaded into the DAC register determines which switch

is closed, connecting the proper node to the amplifier. This configuration guarantees that the DAC is monotonic.

Figure 35. DAC Resistor String

OUTPUT AMPLIFIER

The output buffer amplifier is a rail-to-rail type, providing an output voltage range of 0V to VA. All amplifiers, even

rail-to-rail types, exhibit a loss of linearity as the output approaches the supply rails (0V and VA, in this case). For

this reason, linearity is specified over less than the full output range of the DAC. The output capabilities of the

amplifier are described in the Electrical Tables.

SERIAL INTERFACE

The three-wire interface is compatible with SPI, QSPI and MICROWIRE as well as most DSPs. See the Timing

Diagram for information on a write sequence.

A write sequence begins by bringing the SYNC line low. Once SYNC is low, the data on the DIN line is clocked

into the 16-bit serial input register on the falling edges of SCLK. On the 16th falling clock edge, the last data bit is

clocked in and the programmed function (a change in the mode of operation and/or a change in the DAC register

contents) is executed. At this point the SYNC line may be kept low or brought high. In either case, it must be

brought high for the minimum specified time before the next write sequence as a falling edge of SYNC is used to

initiate the next write cycle.

Product Folder Links: DAC081S101

DATA BITS

0 0 Normal Operation

0 1 1 k to GND

1 0 100 k to GND

1 1 High Impedance

MSB

X X PD1 PD0 D7 D6 D5 D4 D3 D2 D1 D0 X X X X

Power-Down Modes

LSB

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Since the SYNC and DIN buffers draw more current when they are high, they should be idled low between write

sequences to minimize power consumption.

INPUT SHIFT REGISTER

The input shift register, Figure 36, has sixteen bits. The first two bits are "don't cares" and are followed by two

bits that determine the mode of operation (normal mode or one of three power-down modes). The contents of the

serial input register are transferred to the DAC register on the sixteenth falling edge of SCLK. See Timing

Diagram, Figure 2.

Figure 36. Input Register Contents

Normally, the SYNC line is kept low for at least 16 falling edges of SCLK and the DAC is updated on the 16th

SCLK falling edge. However, if SYNC is brought high before the 16th falling edge, the shift register is reset and

the write sequence is invalid. The DAC register is not updated and there is no change in the mode of operation

or in the output voltage.

POWER-ON RESET

The power-on reset circuit controls the output voltage during power-up. Upon application of power the DAC

made to the DAC.

POWER-DOWN MODES

The DAC081S101 has four modes of operation. These modes are set with two bits (DB13 and DB12) in the

control register.

Table 2. Modes of Operation

DB13 DB12 Operating Mode

0 0 Normal Operation

0 1 Power-Down with 1kΩto GND

1 0 Power-Down with 100kΩto GND

1 1 Power-Down with Hi-Z

When both DB13 and DB12 are 0, the device operates normally. For the other three possible combinations of

these bits the supply current drops to its power-down level and the output is pulled down with either a 1kΩor a

100KΩresistor, or is in a high impedance state, as described in Table 2.

The bias generator, output amplifier, the resistor string and other linear circuitry are all shut down in any of the

power-down modes. However, the contents of the DAC register are unaffected when in power-down, so when

coming out of power down the output voltage returns to the same voltage it was before entering power down.

Minimum power consumption is achieved in the power-down mode with SCLK disabled and SYNC and DIN idled

low. The time to exit power-down (Wake-Up Time) is typically tWU µsec as stated in the A.C. and Timing

Characteristics Table.

APPLICATION INFORMATION

The simplicity of the DAC081S101 implies ease of use. However, it is important to recognize that any data

converter that utilizes its supply voltage as its reference voltage will have essentially zero PSRR (Power Supply

Rejection Ratio). Therefore, it is necessary to provide a noise-free supply voltage to the device.

Product Folder Links: DAC081S101

68HC11 DAC081S101

PC7

SCK

MOSI

SCLK

DIN

SYNC

80C51/80L51 DAC081S101

P3.3

TXD

RXD

SCLK

DIN

SYNC

ADSP-2101/

ADSP2103 DAC081S101

TFS

SCLK

DIN

SCLK

SYNC

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

DSP/MICROPROCESSOR INTERFACING

Interfacing the DAC081S101 to microprocessors and DSPs is quite simple. The following guidelines are offered

to hasten the design process.

ADSP-2101/ADSP2103 Interfacing

Figure 37 shows a serial interface between the DAC081S101 and the ADSP-2101/ADSP2103. The DSP should

be set to operate in the SPORT Transmit Alternate Framing Mode. It is programmed through the SPORT control

Transmission is started by writing a word to the Tx register after the SPORT mode has been enabled.

Figure 37. ADSP-2101/2103 Interface

80C51/80L51 Interface

A serial interface between the DAC081S101 and the 80C51/80L51 microcontroller is shown in Figure 38. The

SYNC signal comes from a bit-programmable pin on the microcontroller. The example shown here uses port line

P3.3. This line is taken low when data is to transmitted to the DAC081S101. Since the 80C51/80L51 transmits 8-

bit bytes, only eight falling clock edges occur in the transmit cycle. To load data into the DAC, the P3.3 line must

be left low after the first eight bits are transmitted. A second write cycle is initiated to transmit the second byte of

data, after which port line P3.3 is brought high. The 80C51/80L51 transmit routine must recognize that the

80C51/80L51 transmits data with the LSB first while the DAC081S101 requires data with the MSB first.

Figure 38. 80C51/80L51 Interface

68HC11 Interface

A serial interface between the DAC081S101 and the 68HC11 microcontroller is shown in Figure 39. The SYNC

line of the DAC081S101 is driven from a port line (PC7 in the figure), similar to the 80C51/80L51.

The 68HC11 should be configured with its CPOL bit as a zero and its CPHA bit as a one. This configuration

causes data on the MOSI output to be valid on the falling edge of SCLK. PC7 is taken low to transmit data to the

DAC. The 68HC11 transmits data in 8-bit bytes with eight falling clock edges. Data is transmitted with the MSB

first. PC7 must remain low after the first eight bits are transferred. A second write cycle is initiated to transmit the

second byte of data to the DAC, after which PC7 should be raised to end the write sequence.

Figure 39. 68HC11 Interface

Microwire Interface

Figure 40 shows an interface between a Microwire compatible device and the DAC081S101. Data is clocked out

on the rising edges of the SCLK signal.

Product Folder Links: DAC081S101

LM4050-4.1

LM4050-5.0

DAC081S101

DIN

SCLK

SYNC VOUT = 0V to 5V

0.47 PF

Input

Voltage

LM4130-4.1

DAC081S101

DIN

SCLK

SYNC VOUT = 0V to 4.080V

0.1 PFC2

2.2 PF

Input

Voltage

MICROWIRE

DEVICE

DAC081S101

SCLK

DIN

SYNC

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Figure 40. Microwire Interface

USING REFERENCES AS POWER SUPPLIES

Recall the need for a quiet supply source for devices that use their power supply voltage as a reference voltage.

Since the DAC081S101 consumes very little power, a reference source may be used as the supply voltage. The

advantages of using a reference source over a voltage regulator are accuracy and stability. Some low noise

regulators can also be used for the power supply of the DAC081S101. Listed below are a few power supply

options for the DAC081S101.

LM4130

The LM4130 reference, with its 0.05% accuracy over temperature, is a good choice as a power source for the

DAC081S101. Its primary disadvantage is the lack of 3V and 5V versions. However, the 4.096V version is useful

if a 0 to 4.095V output range is desirable or acceptable. Bypassing the LM4130 VIN pin with a 0.1µF capacitor

and the VOUT pin with a 2.2µF capacitor will improve stability and reduce output noise. The LM4130 comes in a

space-saving 5-pin SOT23.

Figure 41. The LM4130 as a power supply

LM4050

Available with accuracy of 0.44%, the LM4050 shunt reference is also a good choice as a power regulator for the

DAC081S101. It does not come in a 3 Volt version, but 4.096V and 5V versions are available. It comes in a

space-saving 3-pin SOT-23.

Figure 42. The LM4050 as a power supply

Product Folder Links: DAC081S101

LP2980

DAC081S101

DIN

SCLK

SYNC VOUT = 0V to 5V

1 PF

Input

Voltage ON / OFF

VIN VOUT

LP3985

DAC081S101

DIN

SCLK

SYNC VOUT = 0V to 5V

1 PF0.1 PF

Input

Voltage

0.01 PF

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

The minimum resistor value in the circuit of Figure 42 should be chosen such that the maximum current through

the LM4050 does not exceed its 15 mA rating. The conditions for maximum current include the input voltage at

its maximum, the LM4050 voltage at its minimum, the resistor value at its minimum due to tolerance, and the

DAC081S101 draws zero current. The maximum resistor value must allow the LM4050 to draw more than its

minimum current for regulation plus the maximum DAC081S101 current in full operation. The conditions for

minimum current include the input voltage at its minimum, the LM4050 voltage at its maximum, the resistor value

at its maximum due to tolerance, and the DAC081S101 draws its maximum current. These conditions can be

summarized as

R(min) = ( VIN(max) −VZ(min) / (IA(min) + IZ(max)) (3)

and R(max) = ( VIN(min) −VZ(max) / (IA(max) + IZ(min) ) (4)

where VZ(min) and VZ(max) are the nominal LM4050 output voltages ± the LM4050 output tolerance over

temperature, IZ(max) is the maximum allowable current through the LM4050, IZ(min) is the minimum current

required by the LM4050 for proper regulation, IA(max) is the maximum DAC081S101 supply current, and IA(min)

is the minimum DAC081S101 supply current.

LP3985

The LP3985 is a low noise, ultra low dropout voltage regulator with a 3% accuracy over temperature. It is a good

choice for applications that do not require a precision reference for the DAC081S101. It comes in 3.0V, 3.3V and

5V versions, among others, and sports a low 30 µV noise specification at low frequencies. Since low frequency

noise is relatively difficult to filter, this specification could be important for some applications. The LP3985 comes

in a space-saving 5-pin SOT-23 and 5-bump DSBGA packages.

Figure 43. Using the LP3985 regulator

An input capacitance of 1.0µF without any ESR requirement is required at the LP3985 input, while a 1.0µF

ceramic capacitor with an ESR requirement of 5mΩto 500mΩis required at the output. Careful interpretation

and understanding of the capacitor specification is required to ensure correct device operation.

LP2980

The LP2980 is an ultra low dropout regulator with a 0.5% or 1.0% accuracy over temperature, depending upon

grade. It is available in 3.0V, 3.3V and 5V versions, among others.

Figure 44. Using the LP2980 regulator

Product Folder Links: DAC081S101

DAC081S101

DIN

SCLK

SYNC VOUT

0.1 PF

10 PF

+5V

-5V

+5V

±5V

10 pF

DAC081S101

www.ti.com

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

Like any low dropout regulator, the LP2980 requires an output capacitor for loop stability. This output capacitor

must be at least 1.0µF over temperature, but values of 2.2µF or more will provide even better performance. The

ESR of this capacitor should be within the range specified in the LP2980 data sheet. Surface-mount solid

tantalum capacitors offer a good combination of small size and ESR. Ceramic capacitors are attractive due to

their small size but generally have ESR values that are too low for use with the LP2980. Aluminum electrolytic

capacitors are typically not a good choice due to their large size and have ESR values that may be too high at

low temperatures.

BIPOLAR OPERATION

The DAC081S101 is designed for single supply operation and thus has a unipolar output. However, a bipolar

output may be obtained with the circuit in Figure 45. This circuit will provide an output voltage range of ±5 Volts.

A rail-to-rail amplifier should be used if the amplifier supplies are limited to ±5V.

Figure 45. Bipolar Operation

The output voltage of this circuit for any code is found to be

VO= (VAx (D / 256) x ((R1 + R2) / R1) - VAx R2 / R1) (5)

where D is the input code in decimal form. With VA= 5V and R1 = R2,

VO= (10 x D / 256) - 5V (6)

A list of rail-to-rail amplifiers suitable for this application are indicated in Table 3.

Table 3. Some Rail-to-Rail Amplifiers

AMP PKGS Typ VOS Typ ISUPPLY

PDIP-8

LMC7111 0.9 mV 25 µA

SOT-23-5

SO-8

LM7301 0.03 mV 620 µA

SOT-23-5

LM8261 SOT-23-5 0.7 mV 1 mA

LAYOUT, GROUNDING, AND BYPASSING

For best accuracy and minimum noise, the printed circuit board containing the DAC081S101 should have

separate analog and digital areas. The areas are defined by the locations of the analog and digital power planes.

Both of these planes should be located in the same board layer. There should be a single ground plane. A single

ground plane is preferred if digital return current does not flow through the analog ground area. Frequently a

single ground plane design will utilize a "fencing" technique to prevent the mixing of analog and digital ground

current. Separate ground planes should only be utilized when the fencing technique is inadequate. The separate

ground planes must be connected in one place, preferably near the DAC081S101. Special care is required to

guarantee that digital signals with fast edge rates do not pass over split ground planes. They must always have a

continuous return path below their traces.

The DAC081S101 power supply should be bypassed with a 10µF and a 0.1µF capacitor as close as possible to

the device with the 0.1µF right at the device supply pin. The 10µF capacitor should be a tantalum type and the

0.1µF capacitor should be a low ESL, low ESR type. The power supply for the DAC081S101 should only be

used for analog circuits.

Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the

board. The clock and data lines should have controlled impedances.

Product Folder Links: DAC081S101

DAC081S101

SNAS323C –JUNE 2005–REVISED FEBRUARY 2013

www.ti.com

REVISION HISTORY

Changes from Revision B (February 2013) to Revision C Page

• Changed layout of National Data Sheet to TI format .......................................................................................................... 19

Product Folder Links: DAC081S101

PACKAGE OPTION ADDENDUM

www.ti.com 1-Nov-2013

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

DAC081S101CIMK NRND SOT DDC 6 1000 TBD Call TI Call TI -40 to 105 X65C

DAC081S101CIMK/NOPB ACTIVE SOT DDC 6 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X65C

DAC081S101CIMKX/NOPB ACTIVE SOT DDC 6 3000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X65C

DAC081S101CIMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X64C

DAC081S101CIMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X64C

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

PACKAGE OPTION ADDENDUM

www.ti.com 1-Nov-2013

Addendum-Page 2

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

DAC081S101CIMK SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

DAC081S101CIMK/NOPB SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

DAC081S101CIMKX/NOP

BSOT DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3

DAC081S101CIMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

DAC081S101CIMMX/NOP

BVSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 23-Sep-2013

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

DAC081S101CIMK SOT DDC 6 1000 210.0 185.0 35.0

DAC081S101CIMK/NOPB SOT DDC 6 1000 210.0 185.0 35.0

DAC081S101CIMKX/NOP

BSOT DDC 6 3000 210.0 185.0 35.0

DAC081S101CIMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0

DAC081S101CIMMX/NOP

BVSSOP DGK 8 3500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 23-Sep-2013

Pack Materials-Page 2

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265