E2FM-QX2D1-M1GJ-T 0.3M - Omron Automation and Safety

CSM_E2FM_DS_E_4_7

Proximity Sensor with All-stainless Housing

E2FM

Highly Durable Proximity Sensor for

Tough Environments

• Completely stainless-steel housing

• Aluminum chip immunity

• Embedding installation to metal (steel) fittings

• Chemical resistance certified by Ecolab Europe

• Lineup includes pre-wire models and DC 3-wire NPN output

models with fluororesin coating.

Note: Models with a fluororesin coating also use vinyl chloride for the cable material

and require separate protection.

Features

One-piece completely stainless-steel housing with a face thickness of 0.8 mm

The face thickness is approximately 4 times that of

previous models (E2ES) to enable sensing in even more

severe conditions than ever.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Be sure to read Safety Precautions on

page 9.

0.8 mm

Brush Test Continuous Impact Test Chemical and Detergent Proof

The stainless-steel head

means almost no wear

when cleaned with a

metal brush.

E2FM E2EQ

(Spatter-resistant)

After 3 Minutes

E2ES E2FM

The E2ES with a

top wall thickness

of 0.2 mm was

penetrated after

10,000 impacts.

The E2FM was

not penetrated

after 250,000

impacts (depth:

0.26 mm).

More than 20 times the

durability of the E2ES!

The one-piece completely stainless-

steel housing of the sensing section

withstands the following chemicals

better.

•Sodium chloride

•Gasoline

•Dilute sodium hydroxide

•Dilute hydrochloric acid

•Mineral oil

•Barium hydroxide

Any many others

Note: Cannot be used for explosion-proof

applications.

E2FM

Built-in Chip Immunity

Chip immunity performance has been provided to greatly reduce false

signals caused by spatter accumulation and other causes, almost

eliminating the needs for cleaning, e.g., with metal brushes.

Flush Mounting

The chemical resistance has been certified by Ecolab Europe

Main Performance Comparison to Previous OMRON Products

Face thickness Sensing distance Response frequency Ambient operating temperature

Note: When mounted in steel.

E2ES E2FM

Workpiece

Extension

distance

Not influenced by

surrounding

installation

environment.

E2FM E2ES

M8 0.4 mm ---

M12 0.8 mm ---

M18 0.8 mm 0.2 mm

M30 0.8 mm 0.2 mm

E2FM E2ES

M8 1.5 mm ---

M12 2.0 mm ---

M18 5.0 mm 4.0 mm

M30 10.0 mm 8.0 mm

E2FM E2ES

M8 200 Hz ---

M12 100 Hz ---

M18 100 Hz 12 Hz

M30 50 Hz 8 Hz

E2FM E2ES

−25 to 70°C 0 to 50°C

Ecolab GmbH & Co. OHG

P.O. Box 13 04 06

D-40551 Düsseldorf

certifies that for

OMRON Manufacturing of Germany GmbH

Carl-Benz-Strasse 4

71154 Nufringen

material resistance tests

were performed with cleaning substances P3-topax 56, P3-topax 66, P3-topax 91 and

demineralized water as a zero reference factor.

The material resistance of the tested series

Inductive Proximity Sensor E2FM

to the P3 products used in the test can be considered to be positive according to the

cleaning procedure mentioned overleaf.

Düsseldorf, 14th February 2006

Ecolab GmbH & Co. OHG

i.V. i. V.

Thomas Tyborski Reimund Laaff

This certificate is based on:

documented test procedures (test no.: F&E/P3-E Nr. 40-1)

according to material resistance

defined product descriptions

standardized cleaning procedure

Test procedure

Ecolab-test F&E Nr. 40-1

Dipping test:

• Complete immersion in solutions/liquid

Test period:

• 14 days

Temperature:

• room temperature (constant)

Analysis:

Visual judgement like swelling, brittleness,

discoloring

compared to zero-reference factor

(demineralized water)

Photometric documentation

Product specifications:

P3-topax 56:

Acid foam cleaning substance for food and

beverage industry

P3-topax 66:

Alkaline foam cleaning detergent with active

chlorine for machine cleaning in food and

beverage industry

P3-topax 91:

Neutral disinfection agent based on

quaternary ammonium compounds (QAV) for

the food industry

Cleaning plan for food and beverage industry*

Rinsing with water 40 – 50°C

Rinsing with low pressure. Rinsing from top to bottom in the

direction of the drains. Cleaning of the drains.

Foaming from bottom to top

alkaline: P3-topax 66 2 – 5 % daily

acid: P3-topax 56 2 % on demand

temperature: cold up to 40°C

contact time: 15 min. recommended

Rinsing with water 40 – 50°C

Rinsing from top to bottom with low pressure

Spray disinfection P3-topax 91 1-2 %, 30 -60 minutes

*short description

E2FM

Ordering Information

Sensors [Refer to Dimensions on page 10.]

DC 2-Wire, Pre-wired Models

Note: Models with NC operation are also available. Ask your OMRON representative for details.

* Fluororesin-coated models are also available. The model numbers are E2FM-QX@D1. The cable material, however, is vinyl chloride and requires separate protection.

DC 2-wire Pre-wired Smartclick Connector Models (M12)

DC 3-Wire, Pre-wired Models

Note: Models with NC operation are also available. Ask your OMRON representative for details.

DC 3-Wire, M12 Connector Models

* Fluororesin-coated models are also available. The model numbers are E2FM-QX@B1-M1. The cable material, however, is vinyl chloride and requires separate

protection.

Size Sensing distance Output Operation mode Model

Shielded M8

DC 2-Wire

(polarity) NO

E2FM-X1R5D1 2M *

M12 E2FM-X2D1 2M *

M18E2FM-X5D1 2M *

M30 E2FM-X10D1 2M *

Size Sensing distance Output Operation mode Model

Shielded

M8Polarity Pin allocations: 1-4

E2FM-X1R5D1-M1TGJ 0.3M

M12 Polarity Pin allocations: 1-4 E2FM-X2D1-M1TGJ 0.3M

No polarity Pin allocations: 3-4 E2FM-X2D1-M1TGJ-T 0.3M

M18Polarity Pin allocations: 1-4 E2FM-X5D1-M1TGJ 0.3M

No polarity Pin allocations: 3-4 E2FM-X5D1-M1TGJ-T 0.3M

M30 Polarity Pin allocations: 1-4 E2FM-X10D1-M1TGJ 0.3M

No polarity Pin allocations: 3-4 E2FM-X10D1-M1TGJ-T 0.3M

Size Sensing distance Model

Output configuration: NPN NO Output configuration: PNP NO

Shielded M8E2FM-X1R5C1 2M E2FM-X1R5B1 2M

M12 E2FM-X2C1 2M E2FM-X2B1 2M

M18E2FM-X5C1 2M E2FM-X5B1 2M

M30 E2FM-X10C1 2M E2FM-X10B1 2M

Size Sensing distance Model

Output configuration: NPN NO Output configuration: PNP NO

Shielded M8E2FM-X1R5C1-M1 E2FM-X1R5B1-M1 *

M12 E2FM-X2C1-M1 E2FM-X2B1-M1 *

M18E2FM-X5C1-M1 E2FM-X5B1-M1 *

M30 E2FM-X10C1-M1 E2FM-X10B1-M1 *

1.5 mm

2 mm

5 mm

10 mm

1.5 mm

2 mm

5 mm

10 mm

1.5 mm

2 mm

5 mm

10 mm

1.5 mm

2 mm

5 mm

10 mm

E2FM

Accessories (Order Separately)

Sensor I/O Connectors (M12, Sockets on One Cable End)

(Models for Connectors and with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)

[Refer to XS2, XS5.]

Note: Refer to Introduction to Sensor I/O Connectors for details.

Ratings and Specifications

DC 2-Wire (E2FM-X@D@)

Appearance Cable length Sensor I/O Connector model number Applicable Proximity Sensor model number

2m XS2F-D421-DC0-F

E2FM-X@C1-M1

E2FM-X@B1-M1

5m XS2F-D421-GC0-F

2m XS2F-D422-DC0-F

5m XS2F-D422-GC0-F

2m XS5F-D421-D80-F E2FM-X@D1-M1TGJ

E2FM-X@D1-M1TGJ-T

5m XS5F-D421-G80-F

Size M8 M12 M18 M30 M12 M18 M30

Shielded Shielded

Item Model

E2FM-X1R5D1-

E2FM-X2D1-@E2FM-X5D1-@

E2FM-X10D1-

E2FM-X2D1-

M1T1GJ-T

E2FM-X5D1-

M1T1GJ-T

E2FM-X10D1-

M1T1GJ-T

Sensing distance 1.5 mm±10% 2 mm±10% 5 mm±10% 10 mm±10% 2 mm±10% 5 mm±10% 10 mm±10%

Set distance 0 to 1.05 mm 0 to 1.4 mm 0 to 3.5 mm 0 to 7 mm 0 to 1.4 mm 0 to 3.5 mm 0 to 7 mm

Differential travel 15% max. of sensing distance

Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 7.)

Standard sensing object

Iron,

1 mm

Iron,

1 mm

Iron,

1 mm

Iron,

1 mm

Iron,

1 mm

Iron,

1 mm

Iron,

1 mm

Response frequency *1200 Hz 100 Hz 100 Hz 50 Hz 100 Hz 100 Hz 50 Hz

Power supply voltage

(operating voltage range)

12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.

Leakage current 0.8 mA max.

Output configuration With polarity No polarity

Control

output

Switching

capacity 3 to 100 mA

Residual

voltage

3 V max.

(Load current: 100 mA max., Cable length: 2 m)

5 V max.

(Load current: 100 mA max., Cable length: 2 m)

Indicators Operation indicator (red LED), Setting/Operation indicator (green LED)

Operation mode

(with sensing object

approaching)

NO *2

Protection circuits Surge suppressor, Load short-circuit protection

Ambient temperature range

Operating/Storage: −25 to 70°C (with no icing or condensation)

Ambient humidity range

Operating/Storage: 35% to 95% (with no condensation)

Temperature influence ±20% max. of sensing distance at 23°C in the temperature range of −25 to 70°C.

Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range

Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case

Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case

Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions

Shock resistance

Destruction:

500 m/s2

10 times each

in X, Y, and Z

directions

Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions

Degree of protection IEC 60529 IP67

Connection method Unmarked: Pre-wired Models (Standard cable length: 2 m)

Models ending with -M1GJ-@: Pre-wired Connector Models (Standard cable length: 300 mm)

Straight

L-shape

Smartclick

Connector Relay

Models (M12)

E2FM

*1. The response frequency of the DC switching section is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the

standard sensing object, and a set distance of half the sensing distance.

*2. NC (normally closed) models are also available. Contact your OMRON representative.

Weight

(packed

state)

Pre-wired

Models (2 m)

Approx. 105 g Approx. 190 g Approx. 215 g Approx. 295 g --- --- ---

Pre-wired

Connector

Models

Approx. 65 g Approx. 85 g Approx. 110 g Approx. 190 g Approx. 85 g Approx. 110 g Approx. 190 g

Materi-

als

Case Stainless steel (SUS303)

Sensing

surface Stainless steel (SUS303)

(thickness) (0.4 mm) (0.8 mm) (0.8 mm)

Clamping

nuts Stainless steel (SUS303)

Cable PVC (flame retardant)

Toothed

washer Zinc-plated iron

Accessories Instruction manual

Size M8 M12 M18 M30 M12 M18 M30

Shielded Shielded

Item Model

E2FM-X1R5D1-

E2FM-X2D1-@E2FM-X5D1-@

E2FM-X10D1-

E2FM-X2D1-

M1T1GJ-T

E2FM-X5D1-

M1T1GJ-T

E2FM-X10D1-

M1T1GJ-T

E2FM

DC 3-Wire (E2FM-X@C@, E2FM-X@B@)

*1. The response frequency of the DC switching section is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the

standard sensing object, and a set distance of half the sensing distance.

*2. NC (normally closed) models are also available. Contact your OMRON representative.

Size M8 M12 M18 M30

Shielded Shielded

Item Model E2FM-X1R5@E2FM-X2@E2FM-X5@E2FM-X10@

Sensing distance 1.5 mm±10% 2 mm±10% 5 mm±10% 10 mm±10%

Set distance 0 to 1.05 mm 0 to 1.4 mm 0 to 3.5 mm 0 to 7 mm

Differential travel 15% max. of sensing distance

Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 7.)

Standard sensing object Iron, 8

1 mm Iron, 12

1 mm Iron, 30

1 mm Iron, 54

1 mm

Response frequency *1200 Hz 100 Hz 100 Hz 50 Hz

Power supply voltage

(operating voltage

range)

12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.

Current consumption 10 mA max.

Output configuration PNP open collector output

Control

output

Switching ca-

pacity 200 mA max.

Residual

voltage 2 V max. (Load current: 200 mA, Cable length: 2 m)

Indicators Operation indicator (yellow LED)

Operation mode

(with sensing object

approaching)

C1 Models: NPN open collector, NO (normally open) *2

B1 Models: PNP open collector, NO (normally open) *2

Protection circuits Reversed power supply polarity protection, Surge suppressor, Load short-circuit protection, and Reversed output po-

larity protection (except the E2FM-X1R5B1-M1)

Ambient temperature

range Operating/Storage: −25 to 70°C (with no icing or condensation)

Ambient humidity range Operating/Storage: 35% to 95% (with no condensation)

Temperature

influence ±20% max. of sensing distance at 23°C in the temperature range of −25 to 70°C.

Voltage influence ±1% max. of sensing distance in the rated voltage ±15% range (using the sensing distance at the rated voltage as

standard)

Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case

Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case

Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions

Shock resistance

Destruction: 500 m/s2

10 times each in X, Y, and Z

directions

Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions

Degree of protection IEC 60529 IP67

Connection method Unmarked: Pre-wired Models (Standard cable length: 2 m)

Models ending with -M1: Connector Models

Weight

(packed

state)

Pre-wired

Models (2 m) --- Approx. 170 g Approx. 190 g Approx. 275 g

Pre-wired

Connector

Models

Approx. 45 g Approx. 55 g Approx. 75 g Approx. 160 g

Materi-

als

Case Stainless steel (SUS303)

Sensing sur-

face Stainless steel (SUS303)

(thickness) (0.4 mm) (0.8 mm)

Clamping

nuts Stainless steel (SUS303)

Toothed

washer Zinc-plated iron

Accessories Instruction manual

E2FM

Engineering Data (Reference Value)

Sensing Area Influence of Sensing Object Size and Material

E2FM-X@E2FM-X1R5@E2FM-X2@

Leakage Current

E2FM-X5@E2FM-X10@E2FM-X@D1-M1TGJ (-T)

Residual Output Voltage

E2FM-X@C@/B@E2FM-X@D1-M1TGJ (-T)

E2FM-X2D@

E2FM-X10@

E2FM-X1R5@

E2FM-X5@

Distance X (mm)

−25 −15−20 −10 −50 5 10152025

Distance Y (mm)

2.5

2.0

1.5

1.0

0.5

0.0

0 5 10 15 20 25

Distance X (mm)

Stainless

steel

(SUS304)

Aluminum

Brass

Copper

Iron

Side length of sensing object: d (mm)

3.0

2.5

2.0

1.5

1.0

0.5

0.0

01015202530355

Distance X (mm)

Iron

Aluminum

Brass

Copper

Stainless

steel

(SUS304)

Side length of sensing object: d (mm)

020406080

Distance X (mm)

Stainless

steel

(SUS304)

Iron

Brass

Aluminum

Copper

Side length of sensing object: d (mm)

0 102030405060 809070

Distance X (mm)

Side length of sensing object: d (mm)

Stainless

steel

(SUS304)

Iron

Brass

Aluminum

Copper

E2FM-X10D1-M1TGJ(-T)

E2FM-X5D1-M1GJ(-T)

E2FM-X2D1-M1TGJ(-T)

E2FM-X1R5D1-

1.0

0.8

0.6

0.4

0.2

0.0

0 5 10 15 20 25 30

Leakage current (mA)

Power supply voltage (V)

1.5

0.5

1 10 50 100 200 1,000

E2FM-X1R5

E2FM-X2

E2FM-X5

E2FM-X10

Residual output voltage (V)

Load current (mA)

1 3 5 1 0 30 50 100

E2FM-X@D1-M1TGJ-T

E2FM-X@D1-@

Residual output voltage (V)

Load current (mA)

E2FM

I/O Circuit Diagrams

DC 2-Wire Models

DC 3-Wire Models

Operation

mode Model Timing chart Output circuit

E2FM-

X@D1-@

E2FM-

X@D1-

M1TGJ-T

Opera-

tion

mode

Output

config-

uration

Model Timing chart Output circuit

NPN

open-

collector

model

E2FM-

X1R5C@

E2FM-

X2C@

E2FM-

X5C@

E2FM-

X10C@

PNP

open-

collector

model

E2FM-

X1R5B@

E2FM-

X2B@

E2FM-

X5B@

E2FM-

X10B@

100 0

Non-sensing area

Sensing object

Unstable

sensing

area

Set position

Stable sensing

area

Proximity sensor

Rated

sensing

distance

OFF

Setting

indicator

(green)

Operation

indicator

(red)

Control

output

(%) 70 (TYP)

0 V

Proximity

sensor

main

circuit

Note: The load can be connected to either the +V or 0 V side.

Load

12 to 24 VDC

Connector Pin

Arrangement

Note: Pins 2 and 3

are not used.

Brown

Blue

Load

12 to 24VDC

Note1. The load can be connected to either the +V or 0 V side.

Proximity

sensor

main

circuit

Note: Pins 1 and 2 are

not used.

Connector Pin

Arrangement

The E2FM-X@@1-M1TGJ-T has no polarity. There is no need to be concerned

about the polarity of pins 3 and 4.

100 0

Non-sensing area Sensing area

Sensing object

Rated

sensing

distance

Proximity senso

OFF

Operation

indicator

(yellow)

Control

output

(%)

0 V

Proximity

sensor

main

circuit

Load

Connector Pin

Arrangement

Note: For Connector Models, the

connection between pins 1, 4 and 3

uses an NO contact, and the

connection between pins 1, 2 and 3

uses an NC contact.

Brown

Black

Blue

* There is no reversed output polarity protection diode.

0 V

Proximity

sensor

main

circuit

DC12 to 24VDC

Load

Connector Pin

Arrangement

Note: For Connector Models, the

connection between pins 1, 4 and 3

uses an NO contact, and the

connection between pins 1, 2 and 3

uses an NC contact.

Brown

Black

Blue

* There is no reversed output polarity protection diode.

E2FM

Safety Precautions

This product is not designed or rated for ensuring

safety of persons. Do not use it for such purposes.

Never use this product with an AC power supply.

Otherwise, explosion may result.

The following precautions must be observed to ensure safe operation.

1. Do not use the Sensor in an environment where inflammable or

explosive gas is present.

2. Do not attempt to disassemble, repair, or modify any Sensors.

3. Power Supply Voltage

Do not use a voltage that exceeds the rated operating voltage

range. Applying a voltage that is higher than the operating voltage

range may result in explosion or fire.

4. Incorrect Wiring

Be sure that the power supply polarity and other wiring is correct.

Incorrect wiring may cause explosion or fire.

5. Connection without a Load

If the power supply is connected directly without a load, the internal

elements may explode or burn. Be sure to insert a load when

connecting the power supply.

Do not use the Sensor under ambient conditions that exceed the

ratings.

1. Do not use the Sensor in the following locations.

(1) Outdoor locations directly subject to sunlight, rain, snow, or

water droplets

(2) Locations subject to atmospheres with chemical vapors, in

particular solvents and acids

(3) Locations subject to corrosive gas

2. The Sensor may malfunction if used near ultrasonic cleaning

equipment, high-frequency equipment, transceivers, cellular

phones, inverters, or other devices that generate a high-frequency

electric field. Refer to the Technical Guide Photoelectric Sensors

for typical measures.

3. Laying the Sensor wiring in the same conduit or duct as high-

voltage wires or power lines may result in incorrect operation and

damage due to induction. Wire the Sensor using a separate

conduit or independent conduit.

4. Cleaning

Never use thinner or other solvents. Otherwise, the Sensor surface

may be dissolved.

● Design

Influence of Surrounding Metal

When the Proximity Sensor is embedded in metal, make sure that the

clearances given in the following table are maintained. The values

depend on the type of nuts used for mounting. Be sure to use the

supplied nuts (SUS303).

(Unit: mm)

Note: The influence from other non-magnetic surrounding metals is nearly the

same as that from aluminum.

Mutual Interference

When installing two or more Sensors face-to-face or side-by-side,

ensure that the minimum distances given in the following table are

maintained.

Chips from Cutting Aluminum

Normally, chips from cutting aluminum or cast iron will not cause a

detection signal to be output even if it adheres to or accumulates on

the detection surface. In the following cases, however, a detection

signal may be output. Remove the cutting chips in these cases.

● Mounting

Do not tighten the nut with excessive force. A washer must be used

with the nut. Do not use tightening force that exceeds the values in the

following table.

WARNING

Precautions for Safe Use

Precautions for Correct Use

d dia.

Item

l d D m n

Model Embedding

material

E2FM-X1R5@Iron 0

4.5 30

Aluminum

10 50 10

4.5

E2FM-X2@Iron 0

840

Aluminum

16 70 16

E2FM-X5@Iron 01802060

Aluminum 16 80 16 20 80

E2FM-X10@Iron 030040100

Aluminum 24 120 24 40 120

(Unit: mm)

Model Item A B

E2FM-X1R5@35 30

E2FM-X2@40 35

E2FM-X5@65 60

E2FM-X10@110 100

1. If d ≥D at the center of the detection

surface where d is the cutting chip size

and D is the detection surface size

2. If the cutting chips are pressed down

Model Dimension

(mm)

E2FM-X1R5@6

E2FM-X2@10

E2FM-X5@16

E2FM-X10@28

DDetection surface

Cutting chip

Cutting chips

Pressed down

Model Torque

E2FM-X1R5@9 N·m

E2FM-X2@30 N·m

E2FM-X5@70 N·m

E2FM-X10@180 N·m

E2FM

Dimensions

Sensors

Pre-wired Models

Pre-wired Connector Models

(Unit: mm)

Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.

M8 × 1

15 dia.

Two clamping

nuts Operation indicators

* 4-dia. vinyl-insulated round cable with 2 conductors

(Conductor cross section: 0.2 mm2, Insulator diameter: 1.4 mm)

4-dia. vinyl-insulated round cable with 3 conductors

(Conductor cross section: 0.2 mm2, Insulator diameter: 1.2 mm)

4-dia. vinyl-insulated round cable (flame

retardant), Standard length; 2 m *

Toothed washer

E2FM-X1R5@

M12 × 1

21 dia.

Two clamping

nuts Operation indicators

* 6-dia. vinyl-insulated round cable with 2 conductors

(Conductor cross section: 0.5 mm2, Insulator diameter: 1.75 mm)

6-dia. vinyl-insulated round cable with 3 conductors

(Conductor cross section: 0.5 mm2, Insulator diameter: 1.75 mm)

6-dia. vinyl-insulated round cable (flame

retardant), Standard length; 2 m *

Toothed washer

E2FM-X2@

M18 × 1

410

29 dia.

Two clamping

nuts Operation indicators

* 6-dia. vinyl-insulated round cable with 2 conductors

(Conductor cross section: 0.5 mm2, Insulator diameter: 1.75 mm)

6-dia. vinyl-insulated round cable with 3 conductors

(Conductor cross section: 0.5 mm2, Insulator diameter: 1.75 mm)

6-dia. vinyl-insulated round cable (flame

retardant), Standard length; 2 m *

Toothed washer

E2FM-X5@

63.5

M30 × 1.5

510

42 dia.

Two clamping

nuts

Operation indicators

* 6-dia. vinyl-insulated round cable with 2 conductors

(Conductor cross section: 0.5 mm2, Insulator diameter: 1.75 mm)

6-dia. vinyl-insulated round cable with 3 conductors

(Conductor cross section: 0.5 mm2, Insulator diameter: 1.75 mm)

6-dia. vinyl-insulated round cable (flame

retardant), Standard length; 2 m *

Toothed washer

E2FM-X10@

Toothed washer

M8 × 1

M12 × 1

15 dia.

Two clamping

nuts Indicator *2

*1. 4-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm

*2. Operation indicator (red/green)

Settin

indicator

reen

)

E2FM-X1R5D@-M1TGJ-@

21 dia.

Tw o

clamping nuts

Toothed washer

Indicator *2

*1. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm

*2. Operation indicator (red/green)

Setting indicator (green)

M12 × 1

E2FM-X2D@-M1TGJ-@

410

M18 × 1

29 dia.

Two clamping

nuts

Toothed washer

Indicator *2 *1

M12 × 1

*1. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm

*2. Operation indicator (red/green)

Settin

indicator

reen

)

E2FM-X5D@-M1TGJ-@

63.5

510

M30 × 1.5

42 dia.

Toothed washer

Two clamping

nuts Indicator *2

M12 × 1

*1. 6-dia. vinyl-insulated round cable (flame retardant), Standard length; 300 mm

*2. Operation indicator (red/green)

Setting indicator (green)

E2FM-X10D@-M1TGJ-@

E2FM

M12 Connector Models

34.5

53.5

15 dia.

Tw o

clamping

nuts

Toothed washer

Four operation indicators (yellow)

M12 × 1

M8 × 1

E2FM-X1R5@@-M1

21 dia.

Two clamping

nuts

Toothed washer

M12 × 1

Four operation indicators (yellow)

M12 × 1

E2FM-X2@@-M1

29 dia.

M18 × 1

Two clamping

nuts

Toothed washer

M12 × 1

Four operation indicators (yellow)

E2FM-X5@@-M1

63.5

510

42 dia.

Two clamping

nuts

Toothed washer

Four operation indicators (yellow)

M30 × 1.5

M12 × 1

E2FM-X10@@-M1

Mounting Hole Dimensions

Dimension M8 M12 M18 M30

F (mm) 8.5 dia. 12.5 dia. 18.5 dia. 30.5 dia.

+0.5

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2014.10

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:

E2FM-X10B1-M1 E2FM-X1R5B1-M1 E2FM-X2B1-M1 E2FM-X5B1-M1 E2FM-QX5D1-M1GJ 0.3M E2FM-X10C1

2M E2FM-X10C1-M1 E2FM-X10D1 2M E2FM-X1R5B1 2M E2FM-X1R5C1 2M E2FM-X1R5C1-M1 E2FM-X1R5D1

2M E2FM-X2C1 2M E2FM-X2C1-M1 E2FM-X5C1 2M E2FM-X5C1-M1 E2FM-QX10D1 2M E2FM-QX10D1-M1GJ

0.3M E2FM-QX10D1-M1GJ-T 0.3M E2FM-QX1R5B1-M1 E2FM-QX1R5D1 2M E2FM-QX1R5D1-M1GJ 0.3M E2FM-

QX2B1-M1 E2FM-QX2D1 2M E2FM-QX2D1-M1GJ 0.3M E2FM-QX2D1-M1GJ-T 0.3M E2FM-QX5D1 2M E2FM-

QX5D1-M1GJ-T 0.3M E2FM-X10B1 2M E2FM-X1R5D1 5M E2FM-X2B1 2M E2FM-X2D1 2M E2FM-X5B1 2M

E2FM-X5D1 2M E2FM-X5D1 5M