LPR2430 Series 2.4 GHz 802.15.4 Wireless Industrial Transceivers Integration Guide www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 1 of 75 LPR2430 - 06/23/09 Important Regulatory Information RFM Product FCC ID LPR2430: HSW-Z2430 IC 4492A-Z2430 LPR2430A: HSW-Z2430A IC 4492A-Z2430A LPR2430ER: HSW-Z2430HP IC 4492A-Z2430HP LPR2430ERA: HSW-Z2430HPA IC 4492A-Z2430HPA Note: These units have been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their expense. FCC MPE Requirements Information to user/installer regarding FCC Maximum Permissible Exposure (MPE) limits. Notice to users/installers using the following antennas with RFM RF products: Omnidirectional, Patch and Corner Reflector Antennas: The field strength radiated by these antennas, when connected to RFM RF products, may exceed FCC mandated RF exposure limits. FCC rules require professional installation of these antennas in such a way that the general public will not be closer than 20 cm from the radiating aperture of any of these antennas. End users of these systems must also be informed that RF exposure limits may be exceeded if personnel come closer than 20 cm to the apertures of any of these antennas. See Section 3.10 of this manual for regulatory notices and labeling requirements. Changes or modifications to LPR2430, LPR2430A, LPR2430ER or LPR2430ERA modules not expressly approved by RFM may void the user's authority to operate the module. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 2 of 75 LPR2430 - 06/23/09 Table of Contents 1.0 Introduction ......................................................................................................................................... 5 1.1 Features........................................................................................................................................... 6 1.2 Applications...................................................................................................................................... 6 2.0 LPR2430 Series Radio Operation....................................................................................................... 7 2.1 IEEE 802.15.4.................................................................................................................................. 7 2.2 CSMA Channel Access ................................................................................................................... 7 2.3 RF Transmission Error Control ........................................................................................................ 7 2.4 Network Topologies ......................................................................................................................... 7 2.5 Network Formation .......................................................................................................................... 8 2.5.1 Network Association and Registration.......................................................................................... 8 2.5.2 Network Addresses and Leases................................................................................................... 8 2.5.3 Network Relays ............................................................................................................................ 9 2.5.4 Transaction IDs .......................................................................................................................... 10 2.5.5 Broadcast Packets...................................................................................................................... 10 2.3 Security .......................................................................................................................................... 10 2.4 Transparent and Protocol Serial Port Modes ................................................................................ 10 2.4.1 Throughput and Flow Control ..................................................................................................... 11 2.5 Sensor I/O...................................................................................................................................... 11 2.5.1 Automatic Sensor I/O Reporting................................................................................................. 11 2.5.2 I/O Binding .................................................................................................................................. 12 2.6 Sleep Modes .................................................................................................................................. 13 3.0 LPR2430 Series Hardware ............................................................................................................... 15 3.1 Absolute Maximum Ratings ........................................................................................................... 16 3.2 Electrical Specifications ................................................................................................................. 16 3.3 Module Pin Descriptions ................................................................................................................ 16 3.4 RFIO Stripline ................................................................................................................................ 18 3.5 Input Voltages ................................................................................................................................ 19 3.6 ESD and Transient Protection ....................................................................................................... 19 3.7 Interfacing to 5 V Logic Systems ................................................................................................... 20 3.8 Power-On Reset Requirements..................................................................................................... 20 3.9 Mounting and Enclosures .............................................................................................................. 20 3.10 Labeling and Notices ..................................................................................................................... 20 4.0 Serial Protocol................................................................................................................................... 22 4.1 Protocol Message Formats............................................................................................................ 22 4.1.1 Message Types .......................................................................................................................... 23 4.1.2 Message Format Details............................................................................................................. 23 4.1.3 Protocol Escape Sequence ........................................................................................................ 25 4.1.4 Protocol Mode Data Message Example ..................................................................................... 25 4.2 Configuration Registers ................................................................................................................. 26 4.2.1 Bank 0 - Transceiver Setup ........................................................................................................ 26 4.2.2 Bank 1 - System Settings ........................................................................................................... 27 4.2.3 Bank 2 - Status Registers........................................................................................................... 30 4.2.4 Bank 3 - Serial Settings .............................................................................................................. 31 4.2.5 Bank 4 - Host Protocol Settings ................................................................................................. 32 4.2.6 Bank 5 - I/O Peripheral Registers............................................................................................... 33 4.2.7 Bank 6 - I/O Setup ...................................................................................................................... 34 4.2.8 Bank FF - Special Functions ...................................................................................................... 38 4.2.9 Protocol Mode Configuration/Sensor Message Example........................................................... 39 4.2.10 Protocol Mode Event Message Example ................................................................................... 40 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 3 of 75 LPR2430 - 06/23/09 5.0 5.1 5.2 5.3 5.4 5.5 6.0 7.0 7.1 7.2 7.3 7.4 7.5 8.0 LPR2430 Series Developer's Kits..................................................................................................... 41 Items Supplied in a Kit ................................................................................................................... 41 Additional Items Needed................................................................................................................ 41 Developer's Kit Assembly and Testing .......................................................................................... 42 Developer Board Features............................................................................................................. 45 LPRDemo 2.0 Utility Program........................................................................................................ 47 Troubleshooting ................................................................................................................................ 65 Appendices ....................................................................................................................................... 66 Ordering Information...................................................................................................................... 66 Technical Support .......................................................................................................................... 66 LPR2430 Series Mechanical Specifications .................................................................................. 67 Developer Board Schematic, LPR2430A and LPR2430ERA Version........................................... 69 Developer Board Schematic, LPR2430 and LPR2430ER Version ............................................... 72 Warranty............................................................................................................................................ 75 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 4 of 75 LPR2430 - 06/23/09 1.0 Introduction RFM's 2.4 GHz LPR2430 series transceivers provide a low cost solution for point-to-point, point-tomultipoint and peer-to-peer wireless networks. LPR2430 series modules provide the flexibility and versatility to serve applications ranging from cable replacements to sensor networks. Based on the IEEE 802.15.4 wireless standard, LPR2430 series modules are easy to integrate and provide robust wireless communications in applications where full mesh network operation is not required. The LPR2430 series modules include RFM's CNL V2.0 Network Layer firmware, which features a flexible and simple-to-use Application Programming Interface that provides a rich set of module functions. LPR2430 series modules include the LPR2430, which transmits up to 1 mW of RF power. The small footprint and low peak current consumption of the LPR2430 make it ideal for short range applications where small size and low power are required. The LPR2430 is designed for use with an external 2.4 GHz antenna. The LPR2430A adds a chip antenna to the basic LPR2430 circuitry, providing a self contained radio-antenna module. The LPR2430ER transmits up to 63 mW of RF power, making it suitable for longer range applications that are less sensitive to size and power consumption constraints. The LPR2430ER is designed for use with an external 2.4 GHz antenna. The LPR2430ERA adds a chip antenna to the basic LPR2430ER circuitry, providing a self contained radio-antenna module. The RF power level on the LPR2430ER and LPR2430ERA can be readily adjusted to 10 mW for operation under ETSI regulations. All LPR2430 series modules are FCC, Canadian IC and European ETSI certified for unlicensed operation in the world wide 2.4 GHz ISM band. L P R 2 4 3 0 N e tw o rk D ir e c t L P R 2 4 3 0 R e m o te 1 A p p lic a tio n (P C ) L P R 2 4 3 0 B a s e D ir e c t (r e g is tr a tio n ) L P R 2 4 3 0 R e m o te 4 P e e r to P e e r R e la y L P R 2 4 3 0 R e m o te 2 L P R 2 4 3 0 R e m o te 3 Figure 1.0.1 An example LPR2430 network is shown in Figure 1.0.1. An application running on a PC communicates with one or more LPR2430 remote nodes through an LPR2430 series base station. An LPR2430 network supports communications directly between a base and a single remote, referred to as a point-to-point network, or between a base and up to 63 remotes, referred to as point-to-multipoint. Peer-to-peer communications between remotes is also supported following the registration of each remote with the base station. RFM's CNL Network Layer adds an important enhancement to point-to-point and peer-to-peer communications - relay forwarding. One-hop relay forwarding significantly mitigates transmission problems such as multipath fading, but with much less latency and complexity than full mesh network implementations. Thousands of LPR nodes with one-hop relay forwarding have been deployed, demonstrating the robustness it adds to network operation. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 5 of 75 LPR2430 - 06/23/09 An LPR2430 series module is integrated with other components to create a complete node. These components include a host circuit board, a power supply (battery), serial and sensor I/O electronics and/or a host microcontroller, an antenna and a housing. Two common configurations are show in Figure 1.0.2. L P R 2 4 3 0 N o d e w ith H o s t M ic r o c o n tr o lle r L P R 2 4 3 0 N o d e w ith D ir e c t S e n s o r In te r fa c e A D C 0 L P R 2 4 3 0 S e r ie s M o d u le A D C 1 R A D IO _ R X D A D C 2 R A D IO _ T X D A D C _ V D D /H O S T _ R T S L P R 2 4 3 0 S e r ie s M o d u le P W M 0 P W M 1 /H O S T _ C T S G P IO s IN G P IO s O U T G P IO 0 -G P IO 5 R A D IO _ R X D H o s t M ic r o c o n tr o lle r a n d S e n s o r I/O A n a lo g a n d /o r D ig ita l In p u ts A n a lo a n d /o D ig ita O u tp u r g l ts R A D IO _ T X D R S 2 3 2 C o n v e rte r S e r ia l I/O S e r ia l I/O Figure 1.0.2 1.1 Features LPR2430 series modules provide a unique set of features for wireless network applications: * 2.4 GHz world-wide operation * Compliant with IEEE 802.15.4 standard * 128-bit AES data encryption * Relay forwarding for robust, low latency network operation * Low power consumption with sleep mode for long battery life operation * Full -40 to +85 C industrial temperature range operation * Analog and digital I/O plus serial data port * Automatic and/or manual I/O data reporting * Transparent or protocol formatted serial communications * US FCC, Canadian IC and European ETSI certifications * Analog and Digital I/O Binding 1.2 Applications LPR2430 networks are well suited to applications where IEEE 802.15.4 compliance, strong encryption, industrial temperature range operation and long battery life are important. Many applications match these criteria, including: * Encrypted Point-of-Sale Transactions * Security and Access Control Systems * HVAC and other Energy Management Control Systems www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 6 of 75 LPR2430 - 06/23/09 * Industrial Process Control Monitoring * Food and Pharmaceutical Processing 2.0 LPR2430 Series Radio Operation 2.1 IEEE 802.15.4 The radio and media access control technology used by LPR2430 series modules is base on the IEEE 802.15.4 standard as defined for 2.4 GHz operation. Direct sequence spread spectrum (DSSS) using offset quadrature phase shift keying (O-QPSK) modulation is used for RF transmissions. Data is sent over the air at 250 kb/s, carried on a spreading code running at 2 Mc/s. This provides 9 dB of processing gain against interference from other systems in the 2.4 GHz band. 2.2 CSMA Channel Access As specified by the 802.15.4 standard, LPR2430 series modules use carrier sense multiple access (CSMA) to minimize packet collisions on the RF channel. CSMA is used by many data communication systems including Ethernet. In a CSMA radio network, a radio node that has data to transmit first listens to hear if any other node is transmitting. If the channel is clear, the node transmits its packet. If another node is currently transmitting, the first node waits a random period of time and listens again. This listening/waiting cycle continues until the first node detects a clear channel. When it does, it transmits its data. If two radios detect a clear channel and transmit at the same time, the transmissions will collide and not be successfully received. As discussed in Section 2.3, any node that transmits a packet expects to receive an acknowledgement that the packet was received. The absence of an acknowledgment signals a node to retransmit. Because the transmitting nodes each wait random periods of time before transmitting again, the likelihood is low that the two nodes will both attempt to retransmit at precisely the same time. 2.3 RF Transmission Error Control LPR2430 series modules use Automatic Retransmit reQuests (ARQ) for error control. Any node in a LPR2430 network that sends a packet expects to receive an acknowledgement packet (ACK) in response. If an ACK is not received, the packet is resent until an ACK is received, up to a limit set by the ARQ_AttemptLimit parameter (see Section 4.2.1). The ARQ_AttemptLimit parameter can be used twice. If the ARQ_AttemptLimit is reached without a packet being sent directly to the destination node, the sender node will then attempt to send the packet through a relay node until an ACK is received or the ARQ_AttemptLimit is reached again. Acknowledgements are not used with broadcast transmissions. In this case, the BroadcastNumReps parameter sets the number of times each broadcast transmission will be sent regardless of the success or failure of any transmission. Nodes successfully receiving more than one copy of the transmission will discard the duplicates. 2.4 Network Topologies An LPR2430 series radio network is a point-to-multipoint star configuration consisting of a one base and one to 63 associated remotes. The base always uses the network address of 0x0000. Remotes are assigned network addresses in the range of 0x0001 to 0x003F by the base. A point-to-point system consists of a base and a single remote. Peer-to-peer routing between remotes in a point-to-multipoint network is also supported by LPR2430 series modules. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 7 of 75 LPR2430 - 06/23/09 2.5 Network Formation A network is identified by its PAN ID. Remotes may be configured to join either a specific PAN ID or to join any PAN they find. Multiple networks operating in the same area must be assigned different PAN IDs. When the base is first turned on, it will tune to one of the channels specified in its ChannelList (see Section 4.2.2) and detect if there is already a network with its PAN ID on this channel. If there is, the base will go to another channel in the list and keep trying until it finds an available channel or exhausts its list of channels. The first channel the base finds that is available will be used by the base. The base remains tuned to the channel and listens for requests to join its PAN. Every time the base finds a channel that already has a PAN established with its PAN ID, the base generates an Announce packet indicating that a conflict was detected along with the channel on which the conflict occurred and the PAN ID of the conflict (see Section 4.1.2). If the base cycles through its entire channel list and finds conflicts on every channel, it will repeatedly cycle through its list until an available channel is found or its PAN ID and/or channel mask is reconfigured. It will continue to generate Announce packets as it cycles through the list. Note that the order the base cycles through its ChannelList is indeterminate. When a remote is first turned on, it will tune to the first frequency in its channel mask (see Section 4.2.2), transmit a join request, and listen for a response for 250 ms. If there is more than one frequency enabled in its channel mask, it will loop through transmitting a join request on each frequency and listening for a response. Once this scanning phase is complete, the remote will attempt to associate with the first base it hears that also meets a minimum receive power level set by the NwkFormThreshold parameter (see Section 4.2.2). If no viable responses are received, the scan phase is repeated indefinitely. 2.5.1 Network Association and Registration The normal 802.15.4 association process is used to initially admit remotes to the network. The CNL firmware initiates a registration handshake between the base and remote, and announce packets are generated on both sides to notify their respective hosts that a connection has been made. The base assigns each remote a 16-bit address with the lower 6-bits containing the relevant network address. The base keeps a persistent table of network addresses it has assigned to each remote so that it can assign the same address if a remote leaves the network and comes back. th If a 64 remote attempts to join the network, the base will deny the registration request. The remote will resume the scanning loop, but does not remember a base that denied it, and may request to register again if it encounters it. 2.5.2 Network Addresses and Leases As specified in the 802.15.4 standard, each LPR2430 series radio has a 64-bit MAC address (IEEE address) permanently assigned at the factory, and a 16-bit network address that it receives when it joins a network. All network traffic except association is identified and delivered using network addresses. MAC addresses are only used to uniquely identify radios when they first register. It is the responsibility of the host to keep track of which MAC address corresponds to a given network address, if this information is needed. Each LPR2430 series remote receives a 16-bit network address from the base, of which only the lower 6 bits are used. The address assigned to a given remote is static - it will not change if the remote drops link and rejoins, or if any of the radios in the network are power cycled. The table of network addresses in the base can be cleared if desired by writing to the AddressWipe register. Previously registered nodes will need to be reset or power cycled, at which time they will be assigned new network ad- www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 8 of 75 LPR2430 - 06/23/09 dresses. This is typically used in networks with large numbers of remotes that come and go from the network to allow new remotes to register in place of remotes that have left the area or have otherwise been serviced. A remote will also get a new network address if it joins a different base. Note that 0xFFFF is the broadcast address used to send a message to all nodes. See section 2.5.5. All LPR2430 series remotes including sleeping remotes can be configured to send periodic heartbeat packets. These heartbeats serve the following purposes: * To inform their base that they are still present in the network. The base will generate an Announce message to the host whenever a remote fails to report in. * To control the state of the LINK output signal on a remote. The LINK output is held high when heartbeats are being acknowledged by the base. When a remote sends a heartbeat packet, its base will respond with a heartbeat reply. The interval between heartbeats is derived from the LeasePeriod parameter (analogous to a DHCP lease time) as follows: Normal Heartbeat Interval = one-half the lease period plus a random factor 0 to 511 ms Fast Heartbeat Interval = one-tenth the lease period plus a random factor 0 to 511 ms If the LeasePeriod parameter is set to zero, heartbeats are disabled. In this case the base cannot inform its host that a remote has left the network, and remotes will only drop their LINK signal and look for a new base after being reset or power cycled. Each heartbeat interval is offset by a random factor of 0 to 511 ms to prevent remotes from sending heartbeat packets in lockstep. If the base fails to respond to a heartbeat, the remote will continue to attempt to communicate with its base using relays. If this fails, the remotes period between heartbeats will accelerate from normal to fast until either the base responds or it fails to respond to three heartbeats in a row, at which point the remote will reenter scan mode and attempt to find another base. If the unlinked remote is in protocol mode, an announce packet is issued to its host that the connection has failed. A base maintains a list of lease timers for its network addresses. Whenever a remote's lease timer expires, the base issues an Announce message to its host that the remote has left the network. As mentioned, the address assignment table can be manually cleared by writing to the AddressWipe register. If this operation is performed, none of the remote's networks address will be valid any longer. It is the responsibility of the user to reboot all of the remotes in the network in order for them to receive new network addresses. Otherwise erratic network operation can occur. 2.5.3 Network Relays LPR2430 series modules include one-hop relay packet forwarding to enhance network performance. One-hop relay forwarding mitigates transmission problems such as multipath fading and temporary obstructions without introducing the latency and complexity inherent in a full mesh network. When a remote first joins a network, it is not aware of its neighbors and has not selected a relay node to assist with its communications. To collect this information, a remote scans for other remotes and evaluates their relay potential as a background task. A remote then reports its current relay node selection to the base for use in the base station's relay table. This allows the base to transmit to a remote using the appropriate relay node when necessary. Each remote takes the following actions to update and report its relay selection: * Periodically pings all other remotes and obtains the following scores: www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 9 of 75 LPR2430 - 06/23/09 - Path strength between its base and the candidate remote, as reported by the candidate. - Path strength between itself and the candidate remote, as directly measured. * Ranks the candidate remotes according to the two path strength scores and selects the top score for its relay. * Reports the currently chosen relay to the base with a relay status packet. 2.5.4 Transaction IDs A Transaction ID is an identifier supplied by the host device when sending commands and protocol mode packets to distinguish replies from multiple messages that may be in process. The host application must supply a new value for each packet it sends, preferably using a sequence counter that increments for each new command. Transaction IDs for commands and replies are paired - the reply will return the same ID that was sent with the command. Packets such as RxEvent and Announce are not produced in response to a command, but are generated automatically. A separate transaction ID counter is maintained in LPR2430 series modules for events, which is initialized to 0x80 at startup and counts over a range of 0x80 to 0xFF. It is the responsibility of the host application to distinguish the transaction IDs for these packets from the ones that it supplies. This is easily accomplished by the host limiting its transaction IDs to the range 0x00 to 0x7F. 2.5.5 Broadcast Packets Network address 0xFFFF is used for broadcast packets. Since ARQ is not practical for broadcasts, a broadcast packet is sent multiple times. The number of times a broadcast packet is sent is controlled by the BroadcastNumReps parameter (default value of 4). To reduce the chance of a collision with other network packets, a random delay of 0 to BroadcastMaxBackoff is observed between broadcast transmissions (default value is 250 ms). See Section 4.2.2 for more broadcast parameter details. Note that sleeping remotes cannot receive broadcasts. While broadcast packets are intended primarily for use by the base station, they may be originated by a remote if necessary. The same distribution rules apply. 2.3 Security LPR2430 series modules provide optional security from eavesdropping and unauthorized access by scrambling messages with a 128-bit AES key. Nodes that do not have the same security settings cannot communicate with each other. All nodes in a network must have the same security settings. Security keys must be commissioned on a node-by-node basis, either through the serial interface or through the RF interface. When using the RF interface, note that transmitting new keys over the air to a node that does not yet have security enabled makes the keys vulnerable to interception, so this should only be performed in a secure location. Note that a change to a security key does not take effect immediately but requires a restart to take effect. RF packets that are encrypted include RxData, RxEvent, GetRemoteRegister, GetRemoteRegisterReply, SetRemoteRegister, and SetRemoteRegisterReply. Only the payload sections of these packets are encrypted, not the headers. JoinRequest and JoinReply RF packets are not encrypted. 2.4 Transparent and Protocol Serial Modes LPR2430 series modules can work in one of two serial port data modes: transparent or protocol. Transparent mode requires no formatting and is simply the raw user data. Protocol mode formatting includes a start-of-packet framing character, length byte, addressing, command bytes, etc. Transparent mode operawww.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 10 of 75 LPR2430 - 06/23/09 tion is especially useful in point-to-point systems that act as simple cable replacements or in multipoint systems that use an application addressing scheme. In point-to-multipoint systems where the base needs to send data specifically to each remote, protocol formatting must be used. Protocol formatting is also required for configuration commands and responses, and sensor I/O commands and responses. Protocol mode can be used at the base radio while transparent mode is used at the remotes. Protocol formatting details are covered in Section 4. 2.4.1 Throughput and Flow Control LPR2430 series modules can support continuous bidirectional streaming of serial data within the throughput limits of the of the RF channel. For applications that use streaming or operate in encrypted mode, it is recommended that the HOST_CTS signal be observed to avoid overrunning the transmit buffer (flow control is disabled by default). It takes 5 ms to send a transmission independent of the payload data length, and 5 ms to return an ACK. This sets an upper limit of 100 acknowledged transmissions per second. Packets without encryption can carry up to 87 bytes, and packets with encryption can carry up to 66 bytes. The network capacity is 100 x 87 x 10 = 87 kb/s for non-encrypted data and 100 x 66 x 10 = 66 kb/s for encrypted data. These throughputs are maximums, and the actual throughputs will be less due to retries and channel contention. Where individual message streams can be longer than 66 bytes when using encryption or longer than 87 bytes when not using encryption, flow control is recommended to avoid transmit buffer overruns and lost data. 2.5 Sensor I/O In addition to serial I/O, LPR2430 series modules include analog and digital I/O to support sensor network applications. Three ADC inputs, two PWM (DAC) outputs and six general purpose digital I/O ports are provided. LPR2430 series modules include commands to read each of the three ADC inputs individually. Commands are also provided to set each of the two PWM (DAC) outputs individually, plus commands to set the initial value of each PWM output at power up. To support the six digital GPIO ports, LPR2430 series modules include commands to set digital I/O direction, read inputs, write outputs and set the outputs at power up and when sleeping. When configured as inputs, four of the GPIO lines can be configured as interrupts to the module. Any combination of these four lines can be enabled as interrupts simultaneously. 2.5.1 Automatic Sensor I/O Reporting LPR2430 series remotes are capable of automatically sending reports of their current digital and analog I/O readings in response to a set of programmable trigger conditions. When a trigger occurs, the remote sends an RxEvent message containing the contents of the I/O Register Bank (see Section 4.2.6) from GPIO0 up to and including the EventFlags, but not the PWM settings which are outputs only. When a base receives an RxEvent message it automatically forwards it to its host. The normal ARQ process applies to the sending of an RxEvent message, so while the report is sent multiple times it is possible that an RxEvent may not be received. If timer sleep mode is enabled, an I/O report trigger will wake the radio to send the report message. Sleep mode is not required, however, and automatic I/O reporting may be enabled for non-sleeping remotes. Automatic I/O reporting is enabled by setting one or more I/O triggers using the IO_ReportTrigger register. The IO_ReportTrigger register is a bitmask containing bits to enable each of the following trigger sources: www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 11 of 75 LPR2430 - 06/23/09 I/O Reporting Trigger Sources: bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 ADC2 high/low thresholds ADC1 high/low thresholds ADC0 high/low thresholds Periodic report timer GPIO3 falling edge GPIO2 falling edge GPIO1 falling edge GPIO0 falling edge Each of these triggers has some additional settings. The periodic report timer period is set by the IO_ReportInterval register, the ADCs sample period set by the ADC_SampleInterval, the individual high and low ADC trigger thresholds are set by ThresholdLo and ThresholdHi parameters, and GPIOs falling edge triggers are enabled on the GPIO_ EdgeTrigger register (see Section 4.2.7). When a trigger fires, only a single I/O report is generated. If the condition persists, as in the case of a GPIO being held low or an ADC input continuing to exceed a threshold value, recurring reports are not generated. Each respective GPIO or ADC must return to its non-triggered condition before it can fire again. Each trigger source is independent. For instance, if a report is generated in response to an ADC trigger and the ADC remains above the threshold, a subsequent GPIO edge trigger can generate another report. Should additional events occur while an event report is being sent, flags for these events will be accumulated and sent as a follow on report. 2.5.2 I/O Binding I/O binding configures a module to map the states of GPIO0 and GPIO1, and the value of ADC0 contained in an I/O report sent to it by another module to its GPOI2, GPIO3 and PWM0 outputs. The mapping is shown in Table 2.5.2.1. This function can be enabled independently from the other I/O reporting functions that control when a module transmits its reports. An LPR2430 module can send its I/O report to only one other module address. I/O binding is typically used in a point-to-point application with a single base and remote, although other topologies are possible. A module that receives an I/O report from another module can have its I/O report sent back to that module, to a different module, or to the base. It is only necessary to configure I/O binding on a module that will map its I/O to another module's I/O report. Received I/O Mapped to Output I/O GPIO0 GPIO2 GPIO1 GPIO3 ADC0 PWM0 Table 2.5.2.1 When I/O binding is enabled on a module, GPIO0 and GPIO1 are forced to be inputs, GPIO2 and GPIO3 are forced to be outputs, and the GPIO_Dir and GPIO_Alt settings are ignored for GPIO0..GPIO3. I/O binding requires the sending module to have one or more automatic I/O reporting triggers enabled, as discussed in Section 2.5.1. The receiving module must be awake for reliable operation. The sending module can be awake or in one of the sleep modes discussed in Section 2.6. If a sleep mode is being used at the sending node, its WakeDuration timer must be set long enough to receive a response if that is a system requirement. The periodic report timer is used to send I/O mapping updates from the transmitting node that are independent of ADC threshold and GPIO edge trigger events. The minimum practical report timer period is 100 ms, and this setting will consume most of the modules' resources, making other www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 12 of 75 LPR2430 - 06/23/09 traffic such as configuration commands slow. A commonly used configuration is to enable the edge triggers on GPOI0 and GPIO1 and the threshold triggers on ADC0 on the transmitting node to map the onset of an alarm event, and using the report timer set at an interval of several seconds or more to clear the alarm event mapping. This provides fast mapping of an alarm event at the receiving node, with a delay of up to several seconds in mapping the clearing of the event, which is often not critical information. This configuration provides adequate network resources to responsively transmit configuration commands, routine data, etc., in addition to the I/O mapping. 2.6 Sleep Modes To facilitate battery operation, LPR 2430 series modules includes two low power sleep modes, periodic sleep (wake on periodic report timer or I/O triggers), and deep sleep (wake on GPIO triggers only). When a sleep mode is enabled, an LPR2430 series module will stay in a low-power state and only wake up in response to its allowed I/O report triggers. The sleep mode is set by the SleepMode parameter (see Section 4.2.1).The following explains the rules that sleeping remotes follow: * In periodic sleep, the module will wake up when the periodic report timer or any enabled I/O report trigger fires. * In deep sleep, the module will only wake up when an enabled GPIO report trigger fires. * When any of the ADC triggers are enabled in periodic sleep, the module will wake up every ADC_SampleInterval just long enough to sample the ADCs and compare the values against the thresholds and then go back to sleep. The module does not wake up to sample the ADCs in deep sleep. * A remote with either sleep mode enabled will not enter sleep mode until it has associated and registered with a base and has at least one trigger enabled. * After a remote has received an acknowledgement for its I/O report, a WakeDuration timer is started before the remote goes back to sleep. The purpose of this timer is to allow the base a window of time to send a message back to the remote. Note that the only notification the base application will have that a remote is awake is its I/O report packet. In order to send it data, the base application must ensure that the message is transmitted and received before the remote's WakeDuration timer elapses. If this function is not needed, the WakeDuration may be set to zero to disable it. A remote will resend an I/O report if an acknowledgement is not received from the base, until it reaches the ARQ_AttemptLimit. The remote will then remain awake for the duration set by the WakeDuration timer, and go back to sleep. To summarize, while a remote is awake, the following list of checks are used to determine if and when it will go back to sleep: * If the remote receives an acknowledgement for a packet it has sent, it resets the WakeResponseTime timer to remain awake, or if WakeResponseTime is zero it goes back to sleep. * So long as a GPIO for which edge triggered I/O reporting is enabled remains at a logic low, the remote will remain awake. * The remote will remain awake while it still has any ARQ attempts left for a queued transmit packet of any type. * The remote will remain awake while it is has serial characters in its buffer left to transmit to its local host, plus whatever time is required for the last transmitted character to clear the TXD pin. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 13 of 75 LPR2430 - 06/23/09 Sleep functions are controlled by the following registers (see Section 4.2.1): SleepMode - Enables/disables sleep modes WakeDuration - Amount of time that a remote will wait for a response after sending an I/O report Behavior of the GPIO pins during sleep is configured by the GPIO_ SleepMode, GPIO_SleepDir, and GPIO_SleepState parameters. If a module's host application requires a way to monitor whether the module is awake or not, the HOST_CTS signal (alternate function of GPIO4) may be used. HOST_CTS will usually be low (active) when the module is awake and high (internal pullup) when the module is asleep. Alternatively, a user may configure any GPIO to function in a similar way using the GPIO_SleepMode, GPIO_SleepDir and GPIO_SleepState parameters. For example, to configure GPIO3 to generate a logic low when the module is awake, GPIO3 is initialized as a logic low output, the GPIO3 GPIOSleepDir is set to an output, and the GPIO3 GPIO_SleepState is set to a logic high. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 14 of 75 LPR2430 - 06/23/09 3.0 LPR2430 Series Hardware The block diagram of the LPR2430 and LPR2430A is shown in Figure 3.0.1, and the block diagram of the LPR2430ER and LPR2430ERA is shown in Figure 3.0.2. L P R 2 4 3 0 & L P R 2 4 3 0 A B lo c k D ia g r a m 3 2 .7 6 8 k H z G N D 1 A C T IV IT Y 3 2 M H z 2 L IN K 3 G P IO 0 (A D C _ R E F ) 4 R A D IO _ T X D 5 R A D IO _ R X D 6 /H O S T _ C T S (G P IO 4 ) 7 /H O S T _ R T S (G P IO 5 ) 8 2 8 P W M 0 9 G P IO 2 (P W M 1 ) 1 0 G P IO 1 1 1 G P IO 3 (R S 4 8 5 _ E N ) 1 2 P W M 1 (G P IO 2 ) 1 3 F ilte r V C C 1 4 R e g G N D 1 5 C C 8 0 2 R a d M ic r o c F ilte r 2 4 .1 io o n T X /R X C o m b in e r 3 0 5 .4 a n d tr o lle r 2 9 R F IO 3 0 A n L P R 2 4 3 0 r e q u ir e s a n e x te r n a l a n te n n a c o n n e c te d to P in 2 9 a s s h o w n a b o v e . A n L P R 2 4 3 0 A in c lu d e s a n in te g r a l c h ip a n te n n a . N o c o n n e c tio n is m a d e to P in 2 9 . + 3 .3 V 2 4 2 5 2 6 2 7 N C 2 3 A D C _ V D D A D C 1 2 2 N C A D C 0 2 1 A D C 2 G N D /R E S E T 2 0 R S D V 1 9 R S D V 1 8 R S D V 1 7 R S D V 1 6 Figure 3.0.1 L P R 2 4 3 0 E R & L P R 2 4 3 0 E R A B lo c k D ia g r a m 3 2 .7 6 8 k H z G N D 1 A C T IV IT Y + 3 .3 V 3 2 M H z 2 L IN K S w itc h 3 G P IO 0 (A D C _ R E F ) 4 5 R A D IO _ R X D 6 /H O S T _ C T S (G P IO 4 ) 7 /H O S T _ R T S (G P IO 5 ) 8 P W R R A D IO _ T X D 2 8 P W M 0 9 G P IO 2 (P W M 1 ) 1 0 G P IO 1 1 1 G P IO 3 (R S 4 8 5 _ E N ) 1 2 P W M 1 (G P IO 2 ) 1 3 F ilte r V C C 1 4 R e g G N D 1 5 C C 8 0 2 R a d M ic r o c F ilte r 2 4 .1 io o n T X /R X C o m b in e r 3 0 5 .4 a n d tr o lle r T /R T /R F ilte r 2 9 3 0 R F IO P R E A n L P R 2 4 3 0 E R r e q u ir e s a n e x te r n a l a n te n n a c o n n e c te d to P in 2 9 a s s h o w n a b o v e . A n L P R 2 4 3 0 E R A in c lu d e s a n in te g r a l c h ip a n te n n a . N o c o n n e c tio n is m a d e to P in 2 9 . + 3 .3 V 2 5 2 6 2 7 N C R S D V 2 4 A D C _ V D D 2 3 N C 2 2 A D C 2 2 1 R S D V 2 0 R S D V 1 9 R S D V G N D /R E S E T 1 8 A D C 0 1 7 A D C 1 1 6 Figure 3.0.2 The major hardware component of the LPR2430 series modules is the CC2430 IEEE 802.15.4 compliant transceiver with integrated 8051 microcontroller. The LPR2430 series modules operate in the frequency band of 2405 to 2475 MHz. The LPR2430ER and LPR2430ERA include a low noise preamplifier in the receiver path and a power amplifier in the transmitter path, greatly increasing the operating range of the CC2430. Two crystals are provided to operate the CC2430, a 32 MHz crystal for normal operation and a 32.768 kHz crystal for precision sleep mode operation. The LPR2430 series modules provide a variety of application hardware interfaces including a UART interface, three 11-bit ADC inputs, two PWM (DAC) outputs, and six general purpose digital I/O ports. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 15 of 75 LPR2430 - 06/23/09 3.1 Absolute Maximum Ratings Rating Sym Input/Output Pins Except ADC Inputs Value -0.5 to +3.63 Non-Operating Ambient Temperature Range -40 to +85 Units V o C Table 3.1.1 3.2 Electrical Specifications Characteristic Sym Minimum Operating Frequency Range 2405 Operating Frequency Tolerance -300 Spread Spectrum Method Typical Maximum Units 2475 MHz 300 kHz 120 ppm Direct Sequence Modulation Type O-QPSK Number of RF Channels 15 RF Data Transmission Rate 250 Symbol Rate Tolerance RF Channel Spacing kb/s 5 MHz 10E-5 BER Receiver Sensitivity, LPR2430/A -92 dBm 10E-5 BER Receiver Sensitivity, LPR2430ER/ERA -95 dBm Upper Adjacent Channel Rejection, +5 MHz 41 dB Lower Adjacent Channel Rejection, -5 MHz 30 dB Upper Alternate Channel Rejection, +10 MHz 55 dB Lower Alternate Channel Rejection, -10 MHz 53 dB RF Transmit Power, LPR2430 0 dBm RF Transmit Power, LPR2430A 0 dBm RF Transmit Power, LPR2430ER 18 dBm RF Transmit Power, LPR2430ERA 18 dBm Transmit Power Adjustment, LPR2430/A 26 dB Transmit Power Adjustment, LPR2430ER/ERA 20 dB Optimum Antenna Impedance ADC Input Range 3.3 ADC Input Resolution 11 ADC Input Impedance 55 PWM Output Resolution* 8 Data Serial Port Baud Rates 50 0 V bits M 16 1.2, 2.4, 4.8, 9.6 (default), 19.2, 28.8, 38.4, 57.6, 76.8, 115.2 bits kb/s *PWM0 has 8-bit resolution, PWM1 has 16-bit resolution. Built in PWM output filters suppress ripple to 7 bits. Additional filtering can be added externally. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 16 of 75 LPR2430 - 06/23/09 Characteristic Sym Minimum Typical Maximum Units Digital I/O: Logic Low Input Level -0.3 0.5 V Logic High Input Level 2.8 3.6 V Input Pull Up/Down Resistor 20 Logic Low Output Level 0 0.4 V Logic High Output Level 2.4 3.3 V +3.3 +5.5 Vdc 10 mVP-P Power Supply Voltage Range VCC K Power Supply Voltage Ripple Receive Mode Current, LPR2430/A 27 mA Receive Mode Current, LPR2430ER/ERA 33 mA Transmit Mode Current, LPR2430/A 28 mA Transmit Mode Current, LPR2430ER/ERA 130 Sleep Mode Current mA 3 A Operating Temperature Range -40 85 o Operating Relative Humidity Range, Non-condensing 10 90 % C Table 3.2.1 3.3 Module Pin Descriptions Pin Name I/O 1 GND - Power supply and signal ground. Connect to the host circuit board ground. All ground pins must be connected. 2 ACTIVITY O RF activity indicator. Output pulses high when a packet is sent or received. 3 LINK O Link indicator. Output is high when the radio has successfully joined a network. 4 GPIO0 (ADC_REF) I/O Configurable digital I/O port 0. When configured as an output, the power-on state is also configurable. This pin can also be configured as a reference voltage input for the ADCs, 0 to 3.3 V, 1.25 V typical. 5 RADIO_TXD O Serial data output (UART) from the radio to the host. 6 RADIO_RXD I Serial data input (UART) from the host to the radio. 7 GPIO4 (/HOST_CTS ) I/O Configurable digital I/O port 4. When configured as an output, the power-on state is also configurable. Also configurable as UART flow control output. The LPR2430 sets this line low to indicate it is ready to accept data from the host on the RADIO_RXD input. When the LPR2430 sets this line high, the host must stop sending data. The default state is GPIO4. 8 GPIO5 (/HOST_RTS) I/O Configurable digital I/O port 5. When configured as an output, the power-on state is also configurable. Also configurable as UART flow control input. The host sets this line low to allow data to flow from the RADIO_TXD pin. When the host sets this line high, the LPR2430 will stop sending data to the host. The default state is GPIO5 9 PWM0 O Pulse-width modulated output 0 with internal low-pass filter. Provides a DAC function, 0 to 3.3 V. 10 GPIO2 (PWM1) I/O Configurable digital I/O port 2. When configured as an output, the power-on state is also configurable. This pin is connected to the input of the low-pass filter driving Pin 13, and is also configurable as a PWM output. The default setting is for GPIO2. www.RFM.com (c)2009 by RF Monolithics, Inc. Description Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 17 of 75 LPR2430 - 06/23/09 I/O Configurable digital I/O port 1. When configured as an output, the power-on state is also configurable. 12 GPIO3 (RS485_EN) I/O Configurable digital I/O port 3. When configured as an output, this high current port can sink up to 20 mA. The power-on output state is also configurable. Can also be configured as active low transmit enable for controlling an RS485 or other half-duplex bus driver. The default state is GPIO3. 13 PWM1 (GPIO2) O GPIO2 (Pin 10) drives this pin through a low-pass filter. Provides a DAC function when GPIO2 is configured as a PWM output. The default settings is for GPIO2. 14 VCC I Power supply input, +3.3 to +5.5 Vdc. 15 GND - Power supply and signal grounds. Connect to the host circuit board ground. All ground pins must be connected. 16 GND - Power supply and signal grounds. Connect to the host circuit board ground. All ground pins must be connected. 17 /RESET I Active low module hardware reset. Hold this input low when the power supply input is less than 3.3 Vdc. The module firmware boots up and will accept commands about 3 seconds after this input goes high. 18 ADC0 I 7-bit to 12-bit ADC input 0. ADC full scale reading can be referenced to the module's +3.3 V regulated supply, the ADC's internal +2.5 V reference, or ADC_REF (Pin 4). 19 ADC1 I ADC input 1. Same configuration options as ADC0. 20 RSVD - Reserved pin. Leave unconnected. 21 RSVD - Reserved pin. Leave unconnected. 22 RSVD - Reserved pin. Leave unconnected. 23 RSVD - Reserved pin. Leave unconnected. 24 ADC2 I ADC input 2. Same configuration options as ADC0. 25 ADC_VDD O Module's +3.3 V regulated supply, used for ratiometric ADC readings. Current drain should be less than 5 mA. 26 NC - No connection. 27 NC - No connection. 28 GND - RF ground. Connect to the host circuit board ground plane, and to shield when using a coaxial cable. All ground pins must be connected. 29 See Text I/O RFIO port on LPR2430 and LPR2430ER. No connection on LPR2430A and LPR2430ERA. For the LPR2430 and LPR2430ER, connect the antenna to this port with a 50 ohm stripline or semi-rigid coaxial cable. 30 GND - RF ground. Connect to the host circuit board ground plane, and to shield when using a coaxial cable. All ground pins must be connected. 11 GPIO1 Table 3.3.1 3.4 RFIO Stripline To maintain the RF performance of the LPR2430 series modules, the PCB trace running from the RFIO pin of the module to the RF connector or antenna must have an impedance of 50 ohms. This is easily accomplished by controlling the width of the trace. Referring to Figure 3.4.1, the required width of the stripline depends on the dielectric constant and the thickness of the circuit board between the stripline www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 18 of 75 LPR2430 - 06/23/09 and the groundplane. For FR-4 type circuit board materials (dielectric constant of 4.7), the width of the stripline is equal to 1.75 times the thickness of the circuit board. Note that other circuit board traces should be spaced away from the stripline to prevent signal coupling, as shown in Table 3.4.1. The stripline trace should be kept short to minimize its insertion loss. C ir c u it B o a r d S tr ip lin e T r a c e D e ta il C o p p e r S tr ip lin e T ra c e C o p p e r G ro u n d P la n e F R -4 P C B M a te r ia l F o r 5 0 o h m im p e d a n c e W = 1 .7 5 * H Figure 3.4.1 Trace Separation from 50 ohm Microstrip Length of Trace Run Parallel to Microstrip 100 mil 125 mill 150 mil 200 mil 200 mil 290 mil 250 mil 450 mil 300 mil 650 mil Table 3.4.1 3.5 Input Voltages LPR2430 series radio modules can operated from an unregulated DC input (Pin 14) in the range of 3.3 V (trough) to 5.5 V (peak) with a maximum ripple of 5% over the temperature range of -40 to 85 C. Applying AC, reverse DC, or a DC voltage outside the range given above can cause damage and/or create a fire and safety hazard. Further, care must be taken so logic inputs applied to the radio stay within the voltage range of 0 to 3.3 V. Signals applied to the analog inputs must be in the range of 0 to ADC_REF (Pin 25). Applying a voltage to a logic or analog input outside of its operating range can damage the module. 3.6 ESD and Transient Protection LPR2430 series circuit boards are electrostatic discharge (ESD) sensitive. ESD precautions must be observed when handling and installing these components. Installations must be protected from electrical transients on the power supply and I/O lines. This is especially important in outdoor installations, and/or where connections are made to sensors with long leads. Inadequate transient protection can result in damage and/or create a fire and safety hazard. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 19 of 75 LPR2430 - 06/23/09 3.7 Interfacing to 5 V Logic System All logic signals including the serial ports on LPR2430 series modules are 3.3 V signals. To interface to 5 V signals, the resistor divider network shown in Figure 3.8.1 below must be placed between the 5 V signal outputs and the LPR2430 signal inputs. The output voltage swing of the LPR2430 3.3 V signals is sufficient to drive 5 V logic inputs. 5 V L o g ic D N LPR2430 T 5 0 0 2 .2 K 4 .3 K Figure 3.8.1 3.8 Power-On Reset Requirements When applying power to an LPR2430 series module, the /RESET pin should be held low until the power supply voltage reaches 3.3 volts for 100 milliseconds. The module firmware boots up and will accept commands about 3 seconds after this input goes high. 3.9 Mounting and Enclosures LPR2430 series modules are mounted by reflow soldering them to a host circuit board. Refer to Section 7.3 and the LPR2430, LPR2430A, LPR2430ER and LPR2430ERA Data Sheets for mounting details. Enclosures for the LPR2430 series modules must be made of plastics or other materials with low RF attenuation to avoid compromising antenna performance where the antennas are internal to the enclosure. Metal enclosures are not suitable for use with internal antennas as they will block antenna radiation and reception. Outdoor enclosures must be water tight, such as a NEMA 4X enclosure. 3.10 Labeling and Notices LPR2430, LPR2430A, LPR2430ER, and LPR2430ERA FCC Certifications - The LPR2430, LPR2430A, LPR2430ER, and LPR2430ERA hardware has been certified for operation under FCC Part 15 Rules, Section 15.247. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. LPR2430, LPR2430A, LPR2430ER, LPR2430ERA FCC Certification FCC Notices and Labels - This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. A clearly visible label is required on the outside of the user's (OEM) enclosure stating "Contains FCC ID: HSW-Z2430" for the LPR2430, or "Contains HSW-Z2430A" for the LPR2430A, or "Contains FCC ID: HSW-Z2430HP" for the LPR2430ER or "Contains FCC ID: HSW-Z2430HPA" for the LPR2430ERA. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 20 of 75 LPR2430 - 06/23/09 WARNING: This device operates under Part 15 of the FCC rules. Any modification to this device, not expressly authorized by RFM, Inc., may void the user's authority to operate this device. Canadian Department of Communications Industry Notice - IC: 4492A-Z2430 for the LPR2430, IC: 4492A-Z2430A for the LPR2430A, IC: 4492A-Z2430HP for the LPR2430ER, IC: 4492A-Z2430HPA for the LPR2430ERA This apparatus complies with Health Canada's Safety Code 6 / IC RSS 210. ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par Industrie Canada. ETSI EN 300 328 LPR2430 series modules have passed ETSI EN 300 328 testing conducted by an independent test laboratory. USE IN THE EU The LPR2430 series modules are intended for use in the European Union under the following condition: The Effective Isotropic Radiated Power (EIRP), which is the module's RF transmit power plus any antenna gain, must not exceed 12.7 dBm. LPR2430-based products must have the RF transmit power of the module set to meet this requirement, and cannot allow end users of the products to change the module RF transmit power in such a way to exceed the EIRP limit. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 21 of 75 LPR2430 - 06/23/09 4.0 Serial Protocol 4.1 Protocol Message Formats LPR2430 series modules can work in one of two serial port data modes - transparent or protocol. Transparent mode requires no formatting and is simply the raw user data. Protocol mode formatting includes a start-of-packet framing character, length byte, addressing, command bytes, etc. In point-to-multipoint systems where the base needs to send data specifically to each remote, protocol formatting must be used. Protocol formatting is also required for configuration commands and responses, and sensor I/O commands and responses. The configuration of an LPR2430 module is stored in a set of variable length registers. Most registers are read-write, with a few read-only or write-only. Changes made to the register settings are temporary until a MemorySave (to EEPROM) command is executed. Resetting or power-cycling the module will clear any changes that have not been saved to permanent memory using the MemorySave command. LPR2430 series modules can be configured to start in protocol mode at power-up, in which case the EnterProtocolMode command is not required. All protocol messages have a common header format as shown in Figure 4.1.1: 0 1 2 3 4... SOP Length TransID PktType variable number of arguments ... Figure 4.1.1 The scale above is in bytes. * The Start-of-Packet (SOP) character, 0xFB, is used to distinguish the beginning of a message and to assure synchronization in the event of a glitch on the serial port at startup. * The Length byte is defined as the length of the remainder of the message following the length byte itself (or the length of the entire message - 2). * The Packet Type (PktType) byte specifies the type of message. It is a bitfield-oriented specifier, decoded as follows: Bits 7..5 Bit 4 Bits 3..0 Reserved for future use Reply - this bit is set to indicate a packet is a reply Type - these bits indicate the packet type The lower 4 bits (3..0) specify a message type. Bit 4 is a modifier indicating that the message is a command (0) or a reply (1). A reply message has the original command type in bits 3..0. * The transaction ID (TransID) is an identifier supplied by the host device to distinguish replies from multiple commands that may be in process. The host application must supply a new value for each packet it sends, preferably using a sequence counter that increments for each new command. Transaction IDs for commands and replies are paired - the reply will return the same TransID that was sent with the command. Packets such as RxEvent and Announce are not produced in response to a command, but are generated automatically. A separate transaction ID counter is maintained in LPR2430 series modules for events, which is initialized to 0x80 at startup and counts over a range of 0x80 to 0xFF. It is the responsibility of the host to distinguish the transaction IDs for these packets from the ones that it supplies. This is usually accomplished by the host limiting its transaction IDs to the range 0x00 to 0x7F. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 22 of 75 LPR2430 - 06/23/09 * Arguments vary in size and number depending on the type of packet and whether it is a packet sent from the user or a reply from the module. See Table 4.1.2.1 below. Packets that are generated on the serial interface by the user are referred to as host packets. Packets that are generated by the module are referred to as reply packets. For many packet types, there is a reply packet that corresponds to a host packet. For example, when the host sends a TxData packet, the radio will reply to indicate the status of the transmission, whether it succeeded or failed. Some packet types are host-only or reply-only as shown in Table 4.1.2.1. 4.1.1 Message Types Each message generally has two forms, a command from the host and a reply from the module. Depending on the direction, they have different arguments as shown in Table 4.1.2.1. Event messages from the module such as received data packets or status announcements make up a third category of messages. To assist in interpreting the command-reply data flow, the direction is indicated by the high nibble in the message type. For example, an EnterProtocolMode command from the host is a message type 0x00, and the EnterProtocolModeReply from the radio is a message type 0x10. Event messages, including RxData, RxEvent and Announce packets are indicated by 0x20 in the high nibble of the type byte. If multiple arguments are to be provided, they are to be concatenated in the order shown. Little-Endian byte format is used for all multi-byte arguments, where the lowest order byte is the left-most byte of the argument and the highest order byte in the right-most byte of the argument. 4.1.2 Message Format Details Command Reply Event Description Direction Arguments 0x00 - - EnterProtocolMode from Host LPR2400 (ASCII characters) - 0x10 - EnterProtocolModeReply from Radio none 0x01 - - ExitProtocolMode from Host none - 0x11 - ExitProtocolModeReply from Radio none 0x02 - - SoftwareReset from Host none none - 0x12 - SoftwareResetReply from Radio 0x03 - - GetRegister from Host Reg, Bank, Span - 0x13 - GetRegisterReply from Radio Reg, Bank, Span,Val 0x04 - - SetRegister from Host Reg, Bank, Span, Val - 0x14 - SetRegisterReply from Radio none 0x05 - - TxData from Host Addr, Data - 0x15 - - - 0x26 TxDataReply from Radio TxStatus, LQI RxData from Radio Addr, LQI, Data - - 0x27 Announce from Radio AnnStatus, additional fields - - 0x28 RxEvent from Radio Addr, LQI, Data 0x0A - - GetRemoteRegister from Host Addr, Reg, Bank, Span - 0x1A - GetRemoteRegisterReply from Radio 0x0B - - SetRemoteRegister from Host Addr, Reg, Bank, Span, Val - 0x1B - SetRemoteRegisterReply from Radio TxStatus, Addr, LQI - - JoinRequest from Radio MacAddr, NwkAddr, DeviceMode, SleepMode - 0x1C JoinReply from Host PermitStatus 0x2C - TxStatus, Addr, LQI, Reg, Bank, Val Table 4.1.2.1 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 23 of 75 LPR2430 - 06/23/09 Arguments: Reg = Register location (1 byte) Bank = Register bank: provides a logical separation from other data regions (1 byte) Span = Number of bytes of register data to get or set; must align to a parameter boundary (1 byte)) Val = Value to read from or write to register (see Table 4.1.2.1 for size and acceptable range) Data = User data (variable size) Addr = Network address of sender or recipient (2 bytes) MacAddr = MAC address of sender or recipient (8 bytes) TxStatus = Result of last TxData operation (1 byte) 0 = Acknowledgement received 1 = No acknowledgement received 2 = (Remote) Not linked LQI = LQI measurement, 0x01 to 0xFE; values of 0x00 and 0xFF have special meanings: (1 byte) 0x00 = No LQI measured because no ACK was received 0xFF = No LQI measured because packet was relayed PanID = Network identifier of network joined (2 bytes) Channel = Channel number were a PanID conflict was detected (1 byte) AnnStatus = Status announcement (1 byte); additional fields are also reported depending on the status code: Additional fields Status code A0 = Radio has completed startup initialization none A1 = Base: PAN has been formed, ready for data PanID A2 = Base/router: a remote has joined me MacAddr, Addr A3 = Remote/router: joined a PAN, ready for data PanID, Addr A4 = Remote/router: exited PAN (out of range) none A5 = Base: node has left the network Addr A7 = Base: PanID conflict detected PanID, Channel Status codes for error conditions Additional fields E0 = Protocol error - invalid packet type none E1 = Protocol error - invalid argument none E2 = Protocol error - general error none E3 = Protocol error - parser timeout none E4 = Protocol error - register is read-only none E5 = Routing error - unknown destination address none E8 = Serial error - UART receive buffer overflow none E9 = Serial error - UART receive overrun none EA = Serial error - UART framing error none PermitStatus = Permission for new node to join: 0x00 = denied, 0x01 = permitted (1 byte) www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 24 of 75 LPR2430 - 06/23/09 4.1.3 Protocol Escape Sequence The escape sequence is a string of bytes that is input in transparent mode to switch an LPR2430 series module to protocol mode. The escape sequence provides a means of switching between sending transparent data and configuring an LPR2430 series module. The EnterProtocolMode command is used as the escape sequence. The escape sequence must be preceded and followed by a six-character time gap, and must be entered with no interval between characters greater than TransparentModeTimeout interval in order to be accepted. Otherwise, the packet will be sent over-the-air as transparent data. 4.1.4 Protocol Mode Data Message Example In this example, ASCII text Hello is sent from the base to a remote using a TxData command. The network address of the remote is 0x0010. The transaction ID used is 0x02. The protocol formatting for the host message is: SOP Length TransID PktType Addr Addr "H" "e" "l" "l" "o" 0xFB 0x09 0x02 0x05 0x10 0x00 0x48 0x65 0x6C 0x6C 0x6F There are 9 bytes following the length byte, so the length byte is set to 0x09. Note that the 0x0010 network address is entered in Little-Endian byte order 0x10 0x00. When an ACK to this message is received from the remote, the base outputs a TxDataReply message to its host: SOP Length TransID PktType TxStat LQI 0xFB 0x04 0x02 0x15 0x00 0x35 The 0x00 TxStatus byte value indicates the ACK reception from the remote. The LQI value of the received ACK is 0x35, indicating a received signal strength of approximately -70 dBm on an LPR2430 or LPR2430A or -82 dBm on an LPR2430ER or LPR2430ERA. If the remote is in protocol mode, the message is output in the following format: SOP Length TransID PktType Addr Addr LQI "H" "e" "l" "l" "o" 0xFB 0x0A 0x02 0x26 0x00 0x00 0x35 0x48 0x65 0x6C 0x6C 0x6F The message is output as an 0x26 RxData event. The address field contains the sender's address, 0x00 0x00, which is the base. The LQI value 0x35 is the signal strength of the received message. The data following the LQI value is the Hello text. If the remote is in transparent mode, only the Hello text is output. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 25 of 75 LPR2430 - 06/23/09 4.2 Configuration Registers A summary of the configuration registers supported by the LPR2430 series modules is presented in Sections 4.2.1 - 4.2.8 below. Note that registers are organized into banks according to similarity of function. 4.2.1 Bank 0 - Transceiver Setup Size in Bank Reg 00 00 00 00 00 00 00 00 00 00 00 01 03 04 06 08 0A 0B 0C 1C Name DeviceMode InitialPanID SleepMode Reserved WakeDuration Reserved TxPower Reserved Reserved UserTag R/W R/W/R R/W R/W R R/W R/W R/W R R R/W bytes 1 2 1 2 2 2 1 1 16 16 Range Default 0..2 0..2 0 (remote) - must reset after write 0xFFFF 0 (always on) full 0x0000 (disabled) 0..25 0x00 (high power) LPR2430 (ASCII string) Data is specific to each module. The R/W/R designation indicates a reset is required to activate a parameter change. DeviceMode - this parameter selects the operating mode of the LPR2430 series module: 0 = Remote 1 = Reserved 2 = Base The radio module must be reset before a device mode change takes effect. There can be only one base radio for a network. The other device mode setting is reserved for future use. InitialPanID - this parameter is the ID of the PAN a base will use to set up a network or a remote is allowed to join. A value of 0xFFFF instructs a remote to operate in "promiscuous mode" and join any network it finds. A base will use the last two bytes of its MAC address if this parameter is set to 0xFFFF. SleepMode - this parameter enables sleep mode, which may be used in conjunction with the automatic I/O reporting feature to wake up on specified triggers. Sleep mode is only available for remotes. 0 = Always awake 1 = Periodic sleep (wake on periodic timer or any I/O trigger) 2 = Deep sleep (wake on GPIO triggers only) Current consumption is lowest in deep sleep mode, at the expense of having fewer wakeup choices. To prevent the possibility of putting a remote to sleep with no means of waking it back up again, a remote will not go to sleep unless at least one bit of the IO_ReportTrigger register is set. WakeDuration - in sleep mode, this parameter sets the length of time that a remote will wait for a response after sending an I/O report before going back to sleep, from a minimum of 1 ms to a maximum of 65 s. Parameter scaling is 1 ms/count. WakeDuration allows a host application at the base time to respond to a remote before it goes back to sleep. If this capability is not needed, setting this value to 0 will disable the function. TxPower - this parameter sets the level of transmit output power attenuation. Only the values shown in Table 4.2.1.1 are valid: www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 26 of 75 LPR2430 - 06/23/09 TxPower Setting (hex/dec) Relative Output Power Nominal Output Power (0 dBm reference assumed for LPR2430/A) Nominal Output Power (+18 dBm reference assumed for LPR2430ER/A) 0x00 / 0 0 dB 0 dBm 18 dBm 0x01 / 1 -1 dB -1 dBm 17 dBm 0x03 / 3 -3 dB -3 dBm 15 dBm 0x04 / 4 -4 dB -4 dBm 14 dBm 0x05 / 5 -5 dB -5 dBm 13 dBm 0x08 / 8 -7 dB -7 dBm 11 dBm 0x0B / 11 -10 dB -10 dBm 8 dBm 0x0F / 15 -15 dB -15 dBm 3 dBm 0x13 / 19 -19 dB -19 dBm -1 dBm 0x19 / 25 -25 dB -25 dBm -7 dBm Table 4.2.1.1 Power in milliwatts may be related to dBm as follows: (Power in dBm / 10) Power in mW = 10 For operation in regions of Europe where the regulatory limit is 12.7 dBm (18.6 mW), a TxPower setting of 0x05 must be selected on the LPR2430ER/A to ensure compliance. 4.2.2 Bank 1 - System Settings Bank Reg 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 00 01 11 13 14 15 16 17 18 19 1D 1E 20 22 23 Name SecurityMode NetworkKey ChannelList ARQ_AttemptLimit NwkFormThreshold Reserved Reserved BroadcastNumReps BcastMaxBackoff LeasePeriod RemoteLeaseEnable RelayScanRateNorm RelayScanRateFast Reserved Reserved R/W R/W/R W/R R/W R/W R/W R R R/W R/W R/W R/W R/W R/W R R Size in bytes 1 16 2 1 1 1 1 1 1 4 1 2 2 1 1 Range Default 0..1 full 0..32767 0..16 full 0 (security disabled) - must reset after write all 16 bytes 0x00 (NULL) 0x7FFF (all channels 2405 to 2475 MHz) 4 attempts 0x1B (-80 dBm) full 4 0xFA (250 ms) 0x0000EA60 (60 s) 1 (enabled) 0x7530 (30 s) 0x07D0 (2 s) full 0..1 full full Data is specific to each module. The R/W/R designation indicates a reset is required to activate a parameter change. SecurityMode - this parameter enables or disables the security function to encrypt over-the-air packets. A value of 1 enables encryption, a value of 0 disables encryption. The base and all remotes in a network must have the same SecurityMode setting. NetworkKey - this parameter sets the 128-bit AES encryption key that is used to encrypt data, event reports, and GET/SET packets containing data values. All LPR2430 series radios in the network must be configured with the same key in order to interoperate. To protect the key, it is a write-only parameter for www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 27 of 75 LPR2430 - 06/23/09 the user. Refer to Section 2.3 on security for further information. A change to this parameter requires a restart to take effect. ChannelList - this 15-bit bitmask parameter sets the list of channels that an LPR2430 series module is allowed to use. Refer to Table 4.2.1.1 for a list of channels. Note the most significant bit is not used and must be set to 0 for proper operation. For a base radio, it is recommended that only one channel be selected in the ChannelList mask. This provides a known channel for frequency planning purposes. If more than one channel is enabled, the base will pick one of them at random at startup, and not switch from it unless the radio is reset or power-cycled. For a remote, the channel mask specifies which channels it will look for a base on. For greatest flexibility, it is useful to set remotes for all channels, so that the entire network does not need to be reconfigured if it is necessary to assign the base to a new frequency. For faster link time, select as few channels as are required. If a radio loses link, is reset or is power cycled, it will rescan all of the channels in its ChannelList mask continually until its base is found. Bit 0 in the ChannelList mask corresponds to 2405 MHz. Bit 14 corresponds to 2475 MHz. Channel (MHz) ChannelList Bit Mask 2405 0000 0000 0000 0001 2410 0000 0000 000 00010 2415 0000 0000 000 00100 2420 0000 0000 0000 1000 2425 0000 0000 0001 0000 2430 0000 0000 0010 0000 2435 0000 0000 0100 0000 2440 0000 0000 1000 0000 2445 0000 0001 0000 0000 2450 0000 0010 0000 0000 2455 0000 0100 0000 0000 2460 0000 1000 0000 0000 2465 0001 0000 0000 0000 2470 0010 0000 0000 0000 2475 0100 0000 0000 0000 Table 4.2.2.1 ARQ_AttemptLimit - This sets the maximum number of attempts that will be made to send a data packet on the RF link. This number applies to both the direct path and the relay path transmit attempts, so the total number of attempts is effectively twice this limit when a relay is present. A radio will exhaust all of its direct path attempts before switching to the relay path. NwkFormThreshold - This parameter specifies the minimum link quality index (LQI) for a remote to consider acceptable in selecting a base. LQI is related to received signal strength as shown in the table below. The difference in values between the low-power LPR2430/LPR2430A modules and the high-power LPR2430ER/LPR2430ERA modules reflect the additional gain of the extra receiver amplifier. RFM recommends leaving this value at its default setting. Changing it may result in unexpected network operational issues. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 28 of 75 LPR2430 - 06/23/09 Received signal strength in dBm (LPR2430/A) Received signal strength in dBm (LPR2430ER/ERA) LQI (decimal) LQI (hex) special special 255 FF 10 -2 254 FE 5 -7 242 F2 0 -12 229 E5 -5 -17 217 D9 -10 -22 204 CC -15 -27 191 BF -20 -32 179 B3 -25 -37 166 A6 -30 -42 154 9A -35 -47 141 8D -40 -52 128 80 -45 -57 116 74 -50 -62 103 67 -55 -67 90 5A -60 -72 78 4E -65 -77 65 41 -70 -82 53 35 -75 -87 40 28 -80 -92 27 1B -81 -93 25 19 -85 - 15 0F -90 - 2 02 -91 - 1 01 special special 0 00 Table 4.2.1.2 All signal strength values above should be considered approximate ( 3 dB). Values of 0x00 and 0xFF have special meanings. 0x00 = No LQI measured because no ACK was received. 0xFF = No LQI measured because packet was relayed. BroadcastNumReps - this parameter specifies the number of times a broadcast packet will be repeated. Legal values are 0x01 to 0xFF. Setting to 0x00 will have the same effect as setting to 0x01. LeasePeriod - when remote lease periods are enabled, remotes will periodically send a heartbeat to the base to renew their network registration. The base monitors these heartbeat packets to determine when a remote has left the network and to notify its host. The lease period parameter scaling is 1 ms/count. Remotes normally transmit heartbeats to the base at an interval of one-half the LeasePeriod. If a remote does not receive an answer from the base on a given heartbeat attempt, it will switch to a shorter heartbeat interval of one-tenth the LeasePeriod. Generally, the base will notify the host application that a remote has left the network with a latency of less than two-thirds of the LeasePeriod. Setting this value to 0 is equivalent to setting RemoteLeaseEnable to 0. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 29 of 75 LPR2430 - 06/23/09 RemoteLeaseEnable - When set to 1, this parameter enables the remote lease function for a network, allowing it to monitor the connection to each remote in the network and to notify the host application with an announce message whenever a remote leaves the network. This value must be set identically for all radios in the network - base and remotes. RelayScanRateNorm - this parameter specifies the normal period between relay scans. The parameter scaling is 1 ms/count. LPR2430 series modules include one-hop relay packet forwarding to enhance network performance. One-hop relay forwarding mitigates transmission problems such as multipath fading and temporary obstructions without introducing the latency and complexity inherent in a full mesh network. When a remote first joins a network, it is not aware of its neighbors and has not selected a relay node to assist with its communications. To collect this information, a remote scans for other remotes and evaluates their relay potential as a background task. A remote then reports its current relay node selection to the base for use in the base station's relay table. Since conditions often change over time, LPR2430 series modules scan periodically to keep their relay selections current. RelayScanRateFast - When a remote is first turned on, it performs a fast scan of all possible network addresses to initially populate its table of potential relay partners, This parameter specifies the period between relay scans in fast mode. Parameter scaling is 1 ms/count. 4.2.3 Bank 2 - Status Registers Bank Reg 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 00 08 0A 0C 0D 0E 0F 10 12 13 14 15 17 19 20 40 Name MacAddress CurrNwkAddress CurrPanID CurrChannel LinkStatus HardwareVersion FirmwareVersion FirmwareBuildNum Reserved LQI_Last RSSI_Last Reserved Reserved Reserved Reserved Reserved R/W R R R R R R R R R R R R R R R R Size in bytes 8 2 2 1 1 1 1 2 1 1 1 2 2 1 32 64 Range Default full full full 0..16 0..1 full full full factory assigned base = 0xFFFF remote = 0xFFFF 0xFFFF 0x0E (2475 MHz) 0x00 (not joined) 0x00 0x20 0x002F full full Bank 2 contains read-only status registers. Data is specific to each module. MacAddress - this parameter returns the radio's unique 64-bit IEEE MAC address. CurrNwkAddress - this parameter is the module's current network address. Two special values should be noted. The base always reports 0x0000. If a remote does not have a network address assigned it reports 0xFFFF. CurrPanID - this parameter returns the PAN ID of the network the LPR2430 series module is currently connected to. A value of 0xFFFF means the radio is in promiscuous mode and scanning for a network but has not yet joined one. CurrChannel - this parameter returns the current RF channel that the radio is operating on. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 30 of 75 LPR2430 - 06/23/09 LinkStatus - this parameter returns the module's current connection status to the network. The following codes are defined: 0 = not currently part of a network 1 = successfully started or joined a network HardwareVersion - this parameter returns an identifier indicating the LPR2430 series module type. FirmwareVersion - this parameter returns the firmware version of the module in 2-digit BCD format: x.y. FirmwareBuildNum - this parameter returns the firmware build number, in binary format. LQI_Last - this parameter returns the last LQI measurement made during the receipt of an RF packet with a valid CRC. Used for diagnostic purposes and troubleshooting. RSSI_Last - this parameter returns the last RSSI measurement made during receipt of an RF packet with a valid CRC. Used for diagnostic purposes and troubleshooting. 4.2.4 Bank 3 - Serial Settings Bank Reg 03 03 00 01 Name SerialRate SerialParams Size in bytes R/W R/W R/W 1 1 Range Default full 0..56 0x06 (9.6 kb/s) 0x00 (8, n, 1) Data is specific to each module. SerialRate - this parameter selects the UART baud rate. The allowed values are: Hex Value Baud Rate 0x03 1200 0x04 2400 0x05 4800 0x06 9600 0x07 19200 0x08 38400 0x09 57600 0x0A 76800 0x0B 115200 Table 4.2.4.1 SerialParams - this parameter selects the UART parity and stop bit options: Hex value Parity Stop bits 0x00 none 1 0x08 none 2 0x20 even 1 0x28 even 2 0x30 odd 1 0x38 odd 2 other values reserved reserved Table 4.2.4.2 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 31 of 75 LPR2430 - 06/23/09 Note that 8-bit data with no parity is capable of carrying 7-bit data with parity for compatibility without loss of generality for legacy applications that may require it. 4.2.5 Bank 4 - Host Protocol Settings Bank Reg 04 04 04 04 04 04 04 04 00 01 02 03 04 05 06 07 Name ProtocolMode ProtocolOptions TxTimeout Reserved Reserved TransLinkAnnEn EscapeSequenceEn TransDefaultAddr R/W R/W R/W R/W R R R/W R/W R/W Size in bytes 1 1 1 1 1 1 1 2 Range Default 0..2 0..3 full 0x00 (host protocol for point-to-point) 0x03 (Error and Announce packets enabled) 0x32 (50 ms) 0..1 0..1 full 0x00 (<LINK> and <DROP> text inserts disabled) 0x01 (escape sequence enabled at any time) 0xFFFF for a base, 0x0000 for a remote This bank contains options for the host serial protocol. Data is specific to each module. ProtocolMode - this parameter selects transparent point-to-point (0x00), transparent point-to-multipoint (0x01), or protocol mode (0x02). The default is 0x00, transparent point-to-point mode, meaning the LPR2430 series module transmits the characters sent to it transparently, without requiring the host to understand or conform to the LPR2430's serial protocol. This setting is recommended for point-to-point applications such as wire replacements where another serial protocol may already exist. Transparent mode also works well in applications where the data being sent includes addressing information to allow host devices connected to LPR2430 nodes to determine if the data is for them. Setting the base for transparent point-to-multipoint in this environment will cause all of the remotes to receive the data and send it their local host. The local hosts will parse the data to determine if it is for them. Setting this parameter to 0x02 enables the LPR2430 protocol mode, which is the most efficient mode for point-to-multipoint applications. In protocol mode, the module network addresses are used to send specific packets of data to specific remotes. It is not necessary to use the same protocol mode for all LPR2430 modules in a network. For example, it is frequently useful to configure all the remotes for transparent mode and the base for protocol mode. Since by default, data from a remote is sent to the base, there is no need to explicitly address a transmission to the base. It is also possible to establish transparent communications between two remotes by changing the TransDefaultAddr parameter at each remote to the other remote's network address. Note that the host can switch a module from transparent mode to protocol mode and back by using the Enter Protocol Mode escape sequence. See Section 4.1.3 for more information. ProtocolOptions - this parameter is a bitmask that selects various options for the protocol mode. The default is 0x03: bits 2..7 bit 1 bit 0 Reserved Enable error packets Enable announce packets TxTimeout - when a module is in transparent mode, this parameter specifies the length of time of no activity on its RxD line that the module will wait before deciding the message is complete and sending it over the RF link. This is used to prevent any application packet from being unnecessarily split into multiple RF packets. The value is entered in milliseconds. Generally, this value should be set to at least twice the length of a serial character at the currently selected baud rate. If the user's host application is subject to occasional gaps in data that it sends this value should be set higher. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 32 of 75 LPR2430 - 06/23/09 TransLinkAnnEn - this parameter enables a link announcement function for transparent mode. Whenever a link is acquired or dropped, the strings "<LINK>" or "<DROP>" are sent to the host. EscapeSequenceEn - this parameter enables or disables the escape sequence (EnterProtocolMode command) which can be used to switch from transparent mode to protocol mode. Valid settings are 0 = one chance at startup, 1 = enabled at any time. Enabled at anytime is the default. TransDefaultAddr - when an LPR2430 series module is configured for transparent mode, this parameter sets the address where the module will send data packets. For a base, the default will be 0xFFFF, for a remote the default will be 0x0000. To send data from one remote to another remote while in transparent mode, enter the network address of the desired remote into this parameter location. 4.2.6 Bank 5 - I/O Peripheral Registers Bank Reg 05 05 05 05 05 05 05 05 05 05 05 05 05 05 00 01 02 03 04 05 06 08 0A 0C 0E 0F 11 13 Name GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 ADC0 ADC1 ADC2 ADCBatt Temperature EventFlags PWM0 PWM1 R/W R/W R/W R/W R/W R/W R/W R R R R R R R/W R/W Size in bytes 1 1 1 1 1 1 2 2 2 2 1 2 2 2 Range 0..1 0..1 0..1 0..1 0..1 0..1 0..2047 0..2047 0..2047 0..2047 0..255 0..255 full full Default 0x00 (0 V output) 0x00 (0 V output) Data is specific to each module. This bank controls the LPR2430's user-configurable I/O. Values are refreshed upon reading of any register in the bank, and any time any IO is affected, such as event reporting, ADC interval sampling, etc. To simplify block write operations, writes to the read-only ADC0..2, ADCBatt, Temperature and EventFlags registers are ignored and do not generate an error. GPIO0..5 - writing to these registers sets the output states of pins that are configured as outputs. Reading these registers returns the current levels detected on the corresponding pins. ADC0..2 - reading one of these registers returns the latest ADC measurement in 11-bit unsigned integer format. The ADC sampling interval is set by ADC_SampleInterval. Manually reading any one of these registers also refreshes the values of all three ADCs. ADCBatt - reading this register returns an ADC reading of the module's supply voltage (VBatt), in 11-bit unsigned integer format. The actual voltage may be derived from the ADC reading according to the following equation: VBatt = (3.750 * ADCBatt) / 2047 Temperature - reading this register returns the value of the CC2430's internal temperature sensor, in degrees Celsius. Relative error over temperature is 2 C. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 33 of 75 LPR2430 - 06/23/09 EventFlags - when using the automatic I/O reporting feature, this register indicates which I/O events were triggered since the last report message by setting the appropriate flag bits to 1. Once the report is sent, the flags are cleared to 0: bits 15..8 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Reserved ADC2 high/low thresholds ADC1 high/low thresholds ADC0 high/low thresholds Periodic report timer GPIO3 falling edge GPIO2 falling edge GPIO1 falling edge GPIO0 falling edge These flags provide an indication of which triggers generated the current report. This is useful when multiple triggers fire before the report is sent. This reduces unnecessary RF traffic by permitting only one report to be sent. Sending one report also provides better battery life. PWM0..1 - these registers set the PWM outputs. Both PWM registers are 16-bit. However, only the upper 8 bits of PWM0 are significant. All of the bits of PWM1 are significant. The two PWMs also have different periods, 1.024 ms for PWM0 and 2.048 ms for PWM1. Thus each bit of PWM0 = 1.024 ms/256 = 4 s while each bit of PWM1 = 2.048 ms/65,536 = 30 ns. Thus a PWM0 value of 0x80 will produce a 50% duty cycle square wave with a period of 1.024 ms, but it takes a PWM1 value of 0x8000 to produce a 50% duty cycle square wave with a period of 2.048 ms. A simple onboard low-pass filter is provided on the module for both of these outputs, but for best results, these outputs should be buffered and provided with additional filtering. Note that PWM1 shares a pin with GPIO2 and is only enabled when the appropriate bit is set in the GPIO_Alt register. 4.2.7 Bank 6 - I/O Setup Bank Reg 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 00 01 02 03 04 05 06 07 09 0B 0C 0E 10 12 14 16 18 1A 1E 1F 21 22 Name GPIO_Dir GPIO_Init GPIO_Alt GPIO_EdgeTrigger GPIO_SleepMode GPIO_SleepDir GPIO_SleepState PWM0_Init PWM1_Init ADC_Mode ADC_SampleInterval ADC0 ThresholdLo ADC0 ThresholdHi ADC1 ThresholdLo ADC1 ThresholdHi ADC2 ThresholdLo ADC2 ThresholdHi IO_ReportInterval IO_ReportTrigger IO_ReportAddress IO_ReportMode IO_BindingEnable R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Size in bytes 1 1 1 1 1 1 1 2 2 1 1 2 2 2 2 2 2 4 1 2 1 1 Range 0..63 0..63 0..63 full 0..1 0..63 0..63 10 10 0..2 full 0..2047 0..2047 0..2047 0..2047 0..2047 0..2047 full full full 0..1 0..1 Default 0x00 (all inputs) 0x00 (all zeros) 0x00 (no alternate functions) 0x01 (GPIO0 falling edge trigger enabled) 0x00 (all GPIOs inputs/internal pull-ups when sleeping) 0x00 (all inputs) 0x00 (all zeros) 0x0000 (0 V output) 0x0000 (0 V output) 0x00 (VDD referenced full scale) 0x00 (automatic sampling disabled) 0x0000 (0 V) 0x07FF (ADC full scale) 0x0000 (0 V) 0x07FF (ADC full scale) 0x0000 (0 V) 0x07FF (ADC full scale) 0x00007530 (30 s) 0x01 (GPIO0) 0x0000 (base station) 0x01 (send report as an RxEvent packet) 0x00 (RF mapping of I/O disabled) This bank contains setup options for user-configurable I/O. Data is specific to each module. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 34 of 75 LPR2430 - 06/23/09 GPIO_DIR - this parameter is a bitmask that sets whether each GPIO is an input (0 bit) or an output (1 bit). The default is all inputs, 0x00. GPIO_Init - this parameter is a bitmask that sets the initial value for GPIOs set as outputs. GPIO_Alt - this parameter is used to enable alternate GPIO pin functions, such as RS-485 driver enable. Bit Option 7 - 6 - 5 GPIO5 /HOST_RTS 4 GPIO4 /HOST_CTS 3 GPIO3 RS-485 driver 2 GPIO2 PWM1 1 Reserved 0 GPIO0 ADC_REF Table 4.2.7.1 GPIO5 /HOST_RTS: a 1 in this bit position causes GPIO5 to be used as a flow control input from the host to the module to start or stop serial data flow from the module's UART. Note that per convention, the RTS signal (request to send) is active low - a bit value of 0 enables data flow from the module. GPIO4 /HOST_CTS: setting this bit position to 1 causes GPIO4 to be used as a flow control output to the host from the module to start or stop serial data flow from the host. Note that per convention, the CTS signal (clear to send) is active low; a bit value of 0 enables data flow from the host. GPIO3 RS-485 TX Enable: setting this bit position to 1 causes GPIO3 to be used as an active low transmit enable suitable for controlling an RS-485 or other half-duplex bus driver. When enabled, GPIO3 will go low at the beginning of the first start bit, and return to an idle high state at the end of the last stop bit. GPIO2 PWM_1: setting this position to 1 configures GPIO2 as a second PWM output controlled by the PWM1 register. GPIO0 ADC_REF: setting this bit position to 1 configures GPIO0 as a voltage reference input for the ADC. The appropriate ADC mode must also be selected in the ADC_Mode register (discussed later in this section) for the input to be functional. GPIO_EdgeTrigger - this bit mask parameter enables any combination of GPIO0..3 to be used as interrupts to wake a sleeping module: bit 7..4 bit 3 bit 2 bit 1 bit 0 Reserved 0 - disabled; 1 - GPIO3 falling edge enabled 0 - disabled; 1 - GPIO2 falling edge enabled 0 - disabled; 1 - GPIO1 falling edge enabled 0 - disabled; 1 - GPIO0 falling edge enabled For each enabled GPIO, a falling edge wakes up the module and holding the GPIO low keeps the module awake. To have the interrupt generate an IO_Report, the appropriate bit in the IO_ReportTrigger must be set. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 35 of 75 LPR2430 - 06/23/09 GPIO_SleepMode - when this parameter is set to 0x01, it enables the use of the GPIO_SleepDir and GPIO_SleepState registers to configure a direction and state for each GPIO whenever a device is asleep. This function is disabled by default, in which case all GPIOs will be set as inputs with internal pull-ups whenever the module is asleep. GPIO_SleepDir - when GPIO_SleepMode is enabled, the six LSBs of this byte are used to set the direction of the GPIOs during a device's sleep period. A 0 bit value sets a GPIO as an input when sleeping, a 1 bit value sets a GPIO as an output when sleeping. This enables the user to provide alternate configurations during sleep that help minimize current consumption, etc. Bits 0..5 correspond to GPIO0..GPIO5. GPIO_SleepState - when GPIO_SleepMode is enabled, the six LSBs of this byte are used to set the state of any GPIOs configured as outputs by the GPIO_SleepDir parameter during sleep. This enables the user to specify alternate configurations during sleep that help minimize current consumption, etc. Bits 0..5 correspond to GPIO0..GPIO5. PWM0_Init - This sets the initial value for PWM0 at startup. PWM1_Init - This sets the initial value for PWM1 at startup (assuming PWM1 is enabled). ADC_Mode - This register selects the reference voltage that will be used for the internal ADCs. Hex Value ADC Reference 0x00 Internal VDD (3.3 V) 0x01 Internal VREF (2.5 V) 0x02 External VREF (GPIO0) other values Reserved Table 4.2.7.2 If the external VREF is selected, it must also be enabled in the GPIO_Alt register for proper operation. ADC_SampleInterval - this parameter sets the interval at which the ADC will be sampled and threshold levels will be checked for purposes of triggering an I/O event. Parameter scaling is 1 ms/count. Setting the parameter to 0x00 disables automatic sampling. This parameter is different than the IO_ReportInterval in that no report is generated on this interval unless the ADC sample value causes an interrupt to be generated. As long as the ADC threshold triggers are not set or the ADC values are within the ADC threshold limits, the module will return to sleep after taking the samples. ADC0..2_ThresholdLo/Hi - these parameter values define thresholds to trigger an I/O report based on ADC measurements. If I/O reporting is enabled, a single RxEvent report containing the contents of the I/O bank is generated whenever a threshold is crossed. Reporting is edge-triggered with respect to threshold boundaries, not level-triggered. If the measurement remains there, additional reports are not triggered until the value exceeds the threshold again. A second interrupt is not generated when the signal returns to the allowed range. The thresholds are met whenever one of the following inequalities is satisfied: ADCx < ADCx_ThresholdLo ADCx > ADCx_ThresholdHi www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 36 of 75 LPR2430 - 06/23/09 IO_ReportTrigger - when a selected trigger source is enabled, a trigger event will cause the remote to send an RxEvent message to its base containing the entire current values of the I/O Register Bank from GPIO0 up to and including the EventFlags, but not the PWM settings which are output only. bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 ADC2 high/low thresholds ADC1 high/low thresholds ADC0 high/low thresholds Periodic report timer GPIO3 falling edge GPIO2 falling edge GPIO1 falling edge GPIO0 falling edge To avoid inadvertently making an LPR2430 series module non-responsive, a remote will not sleep unless at least one bit in the IO_ReportTrigger register is set. Note that the GPIOs must have first been enabled in the GPIO_EdgeTrigger parameter for them to wake a sleeping module and send a report. IO_ReportInterval - When the periodic timer trigger for I/O reporting is enabled, it sets the interval between reports. The value is entered in milliseconds, and the default is once every 30 seconds. The practical minimum is 100 ms, and the maximum interval is over 49 days. See Section 2.5.2 for details of using the periodic report timer with I/O binding. IO_ReportAddress - Sets the network address that I/O event packets will be sent to (default is the base, 0x0000). Normally, this should be left at the default. However, if the IO_BindingEnable feature is enabled, this should be set to the address of the radio to which it is intended to be bound. IO_ReportMode - When I/O reporting is enabled, this function is used to control the type of report that is sent whenever a GPIO is triggered. This register is a bit field with the following individually selectable switches: bits 7..3 bit 1 bit 0 Reserved LocalReportEnable ReportType LocalReportEnable: a 1 in this bit position causes a remote to output a report on its local serial port as well as sending an RF message. The default is a bit value of 0 (off). ReportType: Controls the type of message sent when an I/O trigger occurs. A 1 in this bit position causes an RxEvent packet to be sent containing an I/O report. A 0 in this bit position causes a registration packet to be sent with no I/O report. The default is a bit value of 1. Note that only GPIO triggers are supported by this function. Timer and ADC triggers always send an RxEvent report, and never produce a local serial report or a registration packet. IO_BindingEnable - setting this parameter to 0x01 configures a module to map the states of GPIO0 and GPIO1, and the value of ADC0 in an I/O report addressed to it from another module to its GPOI2, GPIO3 and PWM0 outputs, as shown in Table 4.2.7.3. This function can be enabled independently from the other I/O reporting functions that control when a module transmits its reports. An LPR2430 module can send its I/O report to only one other module address. IO_BindingEnable is typically used in a point-topoint application with a single base and remote, although other topologies are possible. A module that receives an I/O report from another module can have its I/O report addressed back to that module, to a www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 37 of 75 LPR2430 - 06/23/09 different module, or to the base. It is only necessary to set the IO_BindingEnable on modules that will map another module's I/O report. Received I/O Mapped to Output I/O GPIO0 GPIO2 GPIO1 GPIO3 ADC0 PWM0 Table 4.2.7.3 When I/O binding is enabled on a module, GPIO0 and GPIO1 are forced to be inputs, GPIO2 and GPIO3 are forced to be outputs, and the GPIO_Dir and GPIO_Alt settings are ignored for GPIO0..GPIO3. I/O binding is useful in creating "wireless" analog voltage and switch connections. For example, assume that a remote with network address 0x0002 has a alarm (logic level) connected to GPIO1. To monitor this alarm at another remote with the network address of 0x0005: 1. Connect the alarm signal to GPIO1 on remote 0x0002 2. Set the IO_ReportTrigger on remote 0x0002 to 0x02 (trigger on input GPIO1) 3. Set the IO_ReportMode on remote 0x0002 to 0x01 (send I/O report as RxEvent packet) 4. Set the IO_ReportAddress on remote 0x0002 to 0x0005 (send I/O report to remote 0x0005) 5. Set IO_BindingEnable on remote 0x0005 to 0x01 (enable I/O binding) 6. Monitor the alarm signal on remote 0x0005 output GPIO3 See Section 2.5.2 for addition details on using I/O binding. 4.2.8 Bank FF - Special Functions Bank Reg FF FF FF 00 05 FF Name UcReset AddressWipe MemorySave R/W W R/W/R W Size in bytes 1 1 1 Range Default 0 full 0..1 write 0x00 to reset module any write wipes address after reset write 0x00 to load factory defaults write 0x01 to save to EEPROM This bank contains three user-accessible functions, UcReset, MemorySave and AddressWipe. No attempt should be made to read or write to other parameters in this bank. The functions are specific to each module. UcReset - writing a value of 0x00 to this location forces a software reset of the module's microcontroller causing the module to execute a soft reboot. Writing any other value returns an error. No reply packet, either local or over-the-air, is generated. AddressWipe - on a base, writing any value to this register will clear its table of MAC address - network address associations for remotes. A reset of all radios in the network must be performed after this operation in order to assign new addresses to the remotes. Writing to this register has no effect on a remote. MemorySave - writing a 0x00 to this location restores all registers to factory defaults. Writing a 0x01 to this location commits the current register settings to EEPROM. When programming registers, all changes are temporary until this command is executed. This includes restoring the factory defaults - they are only temporary until 0x01 is written to this location. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 38 of 75 LPR2430 - 06/23/09 4.2.9 Protocol Mode Configuration/Sensor Message Examples In this example, the host configures the base through the serial port to transmit 10 dBm (10 mW) of RF power using the SetRegister command, 0x04. A transaction ID of 0x05 is used. The TxPower parameter is stored in bank 0x00, register 0x0A. A one-byte parameter value of 0x08 selects the 10 dBm (10 mW) power level. The protocol formatting for the command is: SOP Length TransID PktType Reg Bank Span Val 0xFB 0x06 0x05 0x04 0x0A 0x00 0x01 0x08 Note the order of the bytes in the command argument: register, bank, span, parameter value. When the base receives the command it updates the parameter setting and returns a SetRegisterReply message as follows: SOP Length TransID PktType 0xFB 0x02 0x05 0x14 In order for this new RF power setting to persist through a base power down, MemorySave must be invoked. This is done by setting the one-byte parameter in register 0xFF of bank 0xFF to 0x01 with another SetRegister command, with the transaction ID incremented by one: SOP Length TransID PktType Reg Bank Span Val 0xFB 0x06 0x06 0x04 0xFF 0xFF 0x01 0x01 The base will write the current parameter values to EEPROM and return a SetRegisterReply message: SOP Length TransID PktType 0xFB 0x02 0x06 0x14 The change will not take effect until the module is reset or power-cycled. In this example, the base host requests an ADC1 reading from a remote using the GetRemoteRegister command, 0x0A. A transaction ID of 0x07 is used. Since this request is being sent over the air, the network address of the remote is used to address the request - in this example the remote network address is 0x0008. The current ADC1 measurement is read from register 0x08 in bank 0x05. The ADC reading spans two bytes. The protocol formatting for this command is: SOP Length TransID PktType Addr Addr Reg Bank Span 0xFB 0x07 0x07 0x0A 0x08 0x00 0x08 0x05 0x02 Note the remote network address 0x0008 is entered in Little-Endian byte order, 0x08 0x00. The ADC reading is returned in a GetRemoteRegisterReply message: SOP Length TransID PktType TxStatus Addr Addr LQI Reg Bank Lo Val Hi Val 0xFB 0x0A 0x07 0x1A 0x00 0x08 0x00 0x35 0x08 0x05 0xFF 0x02 Substantial information is returned in the message. The last two byes of the message give the ADC reading in Little-Endian format, 0xFF 0x02. The ADC reading is thus 0x02FF. The LQI value is the byte following the address, 0x35, indicating a received signal strength of -70 dBm on an LPR2430 or -82 dBm on an LPR2430ER or LPR2430ERA. The TxStatus byte to the right of the GetRemoteRegisterReply Packet Type is 0x00, showing the packet was acknowledged on the RF channel. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 39 of 75 LPR2430 - 06/23/09 4.2.10 Protocol Mode Event Message Example In this example, the IO_ReportInterval is set to 10 seconds and the periodic report timer bit in the IO_ReportTrigger parameter is set on. The network address of the remote is 0x0008. This causes event messages to be sent from this remote every 10 seconds. The IO_ReportInterval and the IO_ReportTrigger parameters are loaded using SetRemoteRegister commands. The command to set the IO_ ReportInterval to 10 seconds a using transaction ID of 0x09 is: SOP Length TransID PktType Addr Addr Reg Bank Span Lo Val Val Val Hi Val 0xFB 0x0B 0x09 0x0B 0x08 0x00 0x1A 0x06 0x04 0x10 0x27 0x00 0x00 The IO_ReportInterval parameter starts in location 0x1A of bank 0x06. The report interval scaling is 1 ms/count, so a 10 second report interval is 10,000 units or 0x00002710 (Little-Endian format 10 27 00 00). The IO_ReportInterval parameter is updated and SetRemoteRegisterReply is returned: SOP Length TransID PktType TxStat Addr Addr LQI 0xFB 0x06 0x09 0x1B 0x00 0x08 0x00 0x35 The command to set the periodic report timer bit in IO_ReportTrigger using a transaction ID of 0x0A is: SOP Length TransID PktType Addr Addr Reg Bank Span Val 0xFB 0x08 0x0A 0x0B 0x08 0x00 0x1E 0x06 0x01 0x10 The periodic report timer bit in IO_ReportTrigger is located in bit position four (00010000b) or 0x10. The IO_ReportTrigger parameter is updated and SetRemoteRegisterReply is returned: SOP Length TransID PktType TxStat Addr Addr LQI 0xFB 0x06 0x0A 0x1B 0x00 0x08 0x00 0x35 The remote will start sending event messages on 10 second intervals as shown in the log records below: FB FB FB FB 16 16 16 16 80 81 82 83 28 28 28 28 08 08 08 08 00 00 00 00 35 35 35 35 00 00 00 00 01 01 01 01 00 00 00 00 01 01 01 01 0x01 0x00 00 00 00 00 7A 7C 7B 7B 04 04 04 04 36 36 35 35 05 05 05 05 21 25 20 23 01 01 01 01 09 09 08 06 SOP Length TransID PktType Addr Addr LQI 0xFB 0x16 0x80 0x28 0x08 0x00 0x35 GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 0x00 00 00 00 00 0x01 0x00 0x00 ADC0 0x7A 0x04 ADC1 0x36 0x05 07 07 07 07 ADC2 0x21 0x01 1C 1C 1C 1C 10 10 10 10 00 00 00 00 Data BATT 0x09 Temp 0x07 0x1C Flags 0x10 0x00 The IO_ReportTrigger generates RxEvent messages (PktType 0x28). The message payload consists of the first 17 bytes in Bank 5, including the state of GPIO0 through GPIO5, the input voltages measured by ADC0 through ADC2, the battery voltage, the temperature, and the state of the event flags. Note the ADC readings and the event flags are presented in Little-Endian order. The remote is assumed to be always on in this example. If the remote is placed in periodic sleep mode (SleepMode = 1), a suitable value of the WakeDuration parameter should be set to allow the base application to analyze the I/O report and send back a command to the remote as needed. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 40 of 75 LPR2430 - 06/23/09 5.0 LPR2430 Series Developer's Kits Figure 5.1.1 5.1 Items Supplied in a Kit: * * * * * * * Four LPR2430, LPR2430A, LPR2430ER, or LPR2430ERA radios, two of which are installed on developer boards, labeled Base and Remote Two patch antennas, and two dipole antennas with MMCX to SMA-R adaptor cables, LPR2430 and LPR2430ER only (antennas are built into the LPR2430A and LPR2430ERA radios) Two 9 V wall-plug power suppliers, 120/240 VAC, plus two 9 V batteries Two RJ-11 cables with DB-9F adaptors, LPR2430 and LPR2430ER kits Two Cat 5 Ethernet cables with RJ-45/DB-9F adaptors, LPR2430A and LPR2430ERA kits Two A/B USB cables One LPR2430DK/LPR2430ADK/LPR2430ERDK/LPR2430ERADK documentation and software CD 5.2 Additional Items Needed: * One PC with Microsoft Windows XP or Vista Operating System Figure 5.3.1 www.RFM.com (c)2009 by RF Monolithics, Inc. Figure 5.3.2 Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 41 of 75 LPR2430 - 06/23/09 5.3 Developer Kit Setup and Testing: 1. Observe ESD precautions when handling the LPR2430 series developer boards. The developer boards can be powered with either the 9 V wall-plug power supplies or the 9 V batteries. If using the wallplug power supplies, install an AC plug on each supply and connect the power supplies to the developer boards. See Figure 5.3.1 for the location of the power connector. Do not plug in the power supplies at this time. If using the batteries, do not install them yet. 2. For the LPR2430 and LPR2430ER kits, referring to Figures 5.3.1 and 5.3.2, install a patch antenna on each developer board antenna connector. The antenna "snaps" onto the connector with moderate pressure. Antennas are built into the radio modules for the LPR2430A and LPR2430ERA kits. 3. As shown in Figure 5.3.1, there are two serial connectors on the developer boards. The RJ-45 connector or RJ-11 connector provides an RS232 interface. The USB connector provides an optional interface. Labels on the bottom of the boards indicate which board is the Base and which is the Remote. 4a. If the PC has a serial port, use one of the Cat 5 cables with an RJ-45/DB-9F adaptor or one of the RJ11 cables to make a connection to the Base. Then power up the Base by plugging in the power supply or installing the battery. If using a USB connection, follow step 4b instead of 4a. 4b. The USB interface is based on an FT232RL serial-to-USB converter IC manufactured by FTDI. The FT232RL driver files are located in the i386 and AMD64 folders on the kit CD, and the latest version of the drivers can be downloaded from the FTDI website, www.ftdichip.com. The drivers create a virtual COM port on the PC. Power up the Base by plugging in its power supply or installing a battery. Then connect the Base to the PC with one of the USB A/B cables. The PC will find the new USB hardware and open a driver installation dialog window. Enter the letter of the PC drive holding the kit CD and click Continue. The installation dialog will run twice to complete the driver installations. Figure 5.3.3 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 42 of 75 LPR2430 - 06/23/09 5. Copy LPRDemo2.exe from the Programs folder on the kit CD to a convenient folder on the PC. This program runs using ordinary Window's resources and does not require any framework installations, registry entries, etc., to run. Start LPRDemo2. The start-up window is shown in Figure 5.3.3. Figure 5.3.4 6. Click on the Connect button in the lower left of the main LPRDemo2 window to open the Comm Port Settings dialog window, as shown in Figure 5.3.4. Set the Baudrate to 9600 b/s. Set the Comm Port to match the serial port connected to the Base, either the RS232 serial port or the USB virtual serial port. Then click OK to activate the serial connection. Figure 5.3.5 7. At this point the program will collect and display data from the Base under Current Settings on the left side of the main window, as shown in Figure 5.3.5. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 43 of 75 LPR2430 - 06/23/09 Figure 5.3.6 8. Next power up the Remote by plugging in its power supply or installing a battery. Click on the Poll I/O tab. Figure 5.3.6 shows the Poll I/O screen. Select the Remote's network address, 0001, in the Network Address drop-down box for Radio 1. If the address is not present, wait a few seconds to give the remote time to register with the base. 9. Click on the Start button. Data from the Remote will be displayed under Radio 1, including bar graphs of received signal strength (RSSI), and percent of successful requests-replies (%). Note that turning the pot on the Remote developer board will change the Potentiometer (ADC1) reading, and holding Switch 0 down will change the Switch 0 (GPIO0) state to 0. Setting LED 0 (GPIO2) to a 1 state will turn on LED 0. The developer kit is now ready for use. If any difficulty is encountered in setting up your LPR2430 Series Developer's Kit, contact RFM's module technical support group. The phone number is +1.678.684.2000. Phone support is available from 8:30 AM to 5:30 PM US Eastern Time Zone, Monday through Friday. The E-mail address for module technical support is tech_sup@rfm.com. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 44 of 75 LPR2430 - 06/23/09 5.4 Developer Board Features A schematic of the LPR2430/LPR2430ER developer board is provided in the Appendix Section 7.4. The location of key components is shown in Figures 5.4.1 and 5.4.2. Figure 5.4.1 Momentary-contact buttons S1 and S2 set the logic input states to GPIO0 and GPIO1 respectively. Pressing a button presents a logic low to its GPIO input, otherwise the input is logic high. Button S3 provides a hardware reset to the radio. Potentiometer R9 provides an adjustable voltage to the input of ADC1. The voltage to ADC1 decreases as the R9 is turned clockwise. Thermistor RT1 is part of a voltage divider that provides a temperature dependent voltage to the input of ADC0. The voltage to ADC0 decreases with increasing temperature. The Link LED D3 lights on a base station when it finds a clear channel to set up its network (PAN). On remotes, the Link LED illuminates when communication is established with the base. The Activity LED D4 blinks on a base or remote when a packet is transmitted or received. Power LED D11 illuminates when the developer board is receiving adequate voltage for normal operation. The Power LED will go off and the Low Battery LED D12 will illuminate as the input voltage to the developer board drifts toward it lower operating limit. Note that the silkscreen on some developer boards have the label for D11 and D12 switched. LED D5 is illuminated when GPIO3 is configured as a logic high output, and LED D6 is illuminated when GPIO2 is configured as a logic high output. The main silkscreen label on the LPR2430A and LPR2430ERA developer board is "802.15.4 Developer Kit, LPR2430." The label on the LPR2430 and LPR2430ER developer board is "ZigBee Developer Kit, ZMN2430". The LPR2430 and LPR2430ER modules on the developer boards have a different form factor than the LPR2430 and LPR2430ER modules included in the kit but are otherwise identical. Note that while the LPR2430A and LPR2430ERA developer boards support hardware flow control through the RJ-45 RS-232 connector, the LPR2430 and LPR2430ER developer boards only support www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 45 of 75 LPR2430 - 06/23/09 hardware flow control through JP-1 pins 9 (RTS) and 10 (CTS) since they use a 4-pin RJ-11 connector for the RS-232 interface. Hardware flow control is the alternate function for GPIO4 and GPIO5 and must be enabled through bits 4 and 5 of the GPIO_Alt parameter. Figure 5.4.2 There are a number of jumper-configurable options on the developer board, and two jumper strips that provide access to the radio's I/O pins. Removing the jumper on JP-3 disconnects Pot R9 from ADC1, allowing an external signal to be applied to ADC1 on JP-2. Removing the jumper on JP-4 disconnects the thermistor voltage divider from ADC0, allowing an external signal to be applied to ADC0 on JP-2. Note that on some developer boards, ADC0 is labeled ADCX, and ADC1 is labeled ADCY. Removing the jumper on JP-6 disconnects the radio's serial output (UART) from the developer board's RS232/USB circuitry, allowing a direct connection to this logic level signal on JP-2. Likewise, removing the jumper on JP-11 disconnects the radio's serial input (UART) from the developer board's RS232/USB circuitry, allowing a direct connection to this logic level signal on JP-2. GPIO4 and GPIO5 can be configured to provide CTS/RTS hardware flow control. If hardware flow control is not used, removing the jumpers on JP-12 and JP-13 disconnects them from the developer board's RS232/USB circuitry, allowing them to be used for other purposes by connecting to them on jumper strip JP-1. The radio's current consumption can be monitored by removing the jumper on JP-14 and connecting a current meter to its pins. The developer board is normally powered through the power connector or with a 9 V battery, even when communicating through the USB port. The developer board can be optionally powered through the USB port by moving the jumper on JP-12 to the two pins toward the middle of the circuit board, and adding a jumper to J1. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 46 of 75 LPR2430 - 06/23/09 5.5 LPRDemo 2.0 Utility Program LPRDemo2.exe is a Windows-based utility that allows LPR2430 series modules to be configured and exercised. LPRDemo2 configures the modules using the commands detailed in Section 4 of this manual. It is important to note that LPRDemo2 uses protocol mode for all functions except sending and receiving data through the Wincom tab, where transparent mode is used. If the developer board is disconnected from the PC while LPRDemo2 is still running, the module on the developer board will still be in protocol mode. Closing LPRDemo2 before disconnecting the developer board will return the module to transparent mode. Figure 5.5.1 LPRDemo2 starts up displaying the Serial tab, as shown in Figure 5.5.1. Connect PCs to both the Base and the Remote for serial communication testing. Figure 5.5.2 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 47 of 75 LPR2430 - 06/23/09 Pressing the Transmit button on this screen sends the message in the Data to Transmit text box to the selected Network Address. Data sent to the local radio is displayed in the Received Data text box. Received data can be displayed as ASCII or in hexadecimal format (default) by checking the Hex Mode check box. When the Transmit Interval is set to zero, Data to Transmit is sent once when the Transmit button is clicked. When the Transmit Interval is set to a positive number, Pressing the Transmit button once will cause a transmission each transmit interval (seconds) until the button is pressed again. Figure 5.5.3 Figure 5.5.3 shows Received Data in ASCII mode. The Network Address column in the Received Data text box lists the node that sent the message. Figure 5.5.4 Figure 5.5.4 shows Data Received with Hex Mode checked. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 48 of 75 LPR2430 - 06/23/09 Figure 5.5.5 A Packet Builder dialog window can be called from the Options menu. The dialog window facilitates building protocol formatted messages, as discussed in Section 4.0. The four configurations of this dialog window are shown in Figures 5.5.6 through 5.5.9 below. Figure 5.5.6 The Packet drop-down box on the left of Figure 5.5.6 allows the OP Code for any protocol command to be selected and the command transmitted. Figure 5.5.7 After selecting the OP Code as shown in Figure 5.5.6, switch to the Raw Packet tab to see the components of the protocol command. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 49 of 75 LPR2430 - 06/23/09 Figure 5.5.8 The Packet Reply tab displays the OP Code in the response to the transmitted command, and a description of the response message. Figure 5.5.9 After receiving a Packet Reply as shown in Figure 5.5.8, switching to the Raw Packet Reply tab to shows the key components of the protocol replay message. The information shown in these windows should be read from top left to right. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 50 of 75 LPR2430 - 06/23/09 Figure 5.5.10 The Events Tab displays network events useful in understanding network operation. An event message related to a remote joining the PAN network is shown in Figure 5.5.10 above. Figure 5.5.11 LPRDemo2 also has a built-in terminal program, Wincom, which is especially useful for transparent mode communications. Use the F8 key to switch the Wincom screen display from ASCII to hexadecimal. Note that the keyboard does not echo to the terminal program window. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 51 of 75 LPR2430 - 06/23/09 Figure 5.5.12 Figure 5.5.12 shows a text message received by Wincom in ASCII display mode. Figure 5.5.13 Figure 5.5.13 shows a text message received by Wincom in hexadecimal display mode. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 52 of 75 LPR2430 - 06/23/09 Figure 5.5.14 The Poll I/O tab provides an alternate display that shows data on four remotes instead of the Base and three remotes. Clicking on the check box just to the right of the Current Settings text in Figure 5.5.14 switches to the display in Figure 5.5.15. Clicking on the check box to the left of the Serial tab in Figure 5.5.15 switches back to the default display shown in Figure 5.5.14. Figure 5.5.15 A multi-tab Device Config dialog window can be accessed for the Base and each Remote in the network by clicking the radio's Config button. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 53 of 75 LPR2430 - 06/23/09 Refresh, Apply and Cancel buttons are located below the set of tabs on the Device Config dialog window. Clicking the Refresh button loads a copy the configuration parameters currently running in the radio into the tabs on the Device Config window. The Apply button writes all changes made on all the tabs into the radio's EEPROM. The Cancel button closes the Device Config window without writing any changes made on the tabs to the radio. However, once the Apply button has been clicked, Cancel will not undo those changes. Figure 5.5.16 The radio's basic setup can be viewed and configured on the Transceiver Setup tab. The Device Mode drop-down box allows Base or Remote operating mode to be selected. The Initial Pan ID text box displays the current initial PAN ID and accepts changes. Wake Duration specifies how long a Remote stays awake after sending an I/O report in sleep mode. The TX Power text box displays the current transmitter power setting and accepts changes. The User Tag text box displays the current tag and accepts changes. The Sleep Mode drop-down box allows the sleep mode to be viewed and/or changed - Always On, Timer Sleep or Deep Sleep. The radio must be reset in order for some changes, such as device mode, to take effect. Click on Apply, then on Reset to process these changes. Refer to Section 4 to determine which changes require resets. The Defaults button sets all configuration parameters back to their factory default values. Click on Defaults, Apply and then Reset to begin running on factory defaults. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 54 of 75 LPR2430 - 06/23/09 The System tab allows basic system parameters to be viewed and set, as shown in Figure 5.5.17. The Channel Set box specifies the channels the system can use. The Base will establish its network on the first clear channel it finds and will remain there, even if the channel degrades, until it is reset. Specifying the channels a Base can use allows overlapping networks to be coordinated and known noisy channels to be avoided. To enable encryption, set the 128-bit (16 byte) AES Encryption Key and check Enable Encryption. This must be done for all radios in the network. All radios must use the same Encryption Key. The key cannot be read back, so care must be used in setting the keys. The Base uses the Lease Period to detect when a remote has left the network. ARQ Attempt Limit sets the number of transmission retries for an unacknowledged packet. Broadcast Attempts sets the number of times a broadcast packet transmission is repeated. The Relay Scan Rate Normal and Relay Scan Rate Fast parameters set the normal and fast scan intervals for a Remote to update its relay partner table. Figure 5.5.17 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 55 of 75 LPR2430 - 06/23/09 Figure 5.5.18 The Status tab provides read-only status information, as shown in Figure 5.5.18. Figure 5.5.19 The Serial tab provides serial port configuration drop-down boxes that allow the baud rate, parity and number of stop bits to the set. Hardware flow control is set up on the right-most I/O Setup tab. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 56 of 75 LPR2430 - 06/23/09 Figure 5.5.20 The Protocol tab is shown in Figure 5.5.20. The Protocol Mode drop-down box allows the selection of Transparent Multi (point-to-multipoint), Transparent Pt-Pt (point-to-point) and Protocol mode. The Escape Sequence drop-down box allows either Once (one chance at startup) or Unlimited (anytime) to be selected. The TX Timeout and Minimum Packet Length parameters control when transparent data is sent, as discussed in Section 4.2.5. Transparent Default Addr sets the destination address for transparent mode operation. The default for a base is the 0xFFFF network broadcast address. The default for a remote is 0x0000, the base network address. The Startup Announce Enable checkbox enables announce messages. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 57 of 75 LPR2430 - 06/23/09 Figure 5.5.21 Figure 5.5.21 shows the I/O Peripherals tab contents. All GPIO ports are shown configured as inputs (the GPIO ports are configured as inputs or outputs on the left I/O Setup tab). Ports GPIO0-4 have logic high inputs, GPIO5 has a logic low. When a GPIO is defined as an output, its state can be set with its GPIO Value radio buttons. The 11-bit Module Voltage (module power supply voltage), Junction Temperature (module internal temperature) and ADC0, ADC1 and ADC2 readings are given in hexadecimal. The PWM output settings can be read and adjusted in the PWM0 Value (8-bit) and PWM1 Value (16-bit) text boxes. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 58 of 75 LPR2430 - 06/23/09 Figure 5.5.22 Figure 5.5.22 shows the first I/O Setup tab contents. This tab allows the direction of the GPIO ports to be set both for active and sleep modes, and in the case of GPIO outputs, the initial power up states can be set in the GPIO Init column and the sleep mode states can be set in the Sleep I/O State column (check Use Sleep I/O States). The I/O Report Mode, I/O Reporting Interval and I/O Report Address are also configured on this tab. The Enable Binding check box allows specific analog and digital input values from the I/O Report of the base or another remote (I/O Report Address) to be mapped as I/O outputs on this remote. See Table 4.2.7.3 for additional details. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 59 of 75 LPR2430 - 06/23/09 Figure 5.5.23 Figure 5.5.23 shows the second I/O Setup tab contents. The ADC Sample Interval and the Threshold Low and High limits for each ADC channel can be set on this tab, plus the event reporting triggers for each ADC channel. The ADC Mode drop-down box selects the ADC full scale reference. PWM0 Init and PWM1 Init set the start-up output values for each PWM channel. When GPIO0-3 are configured as inputs, I/O Report Triggers can be set for each of them with check boxes. GPIO Alt Functions can also be set under this tab. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 60 of 75 LPR2430 - 06/23/09 Figure 5.5.24 Figure 5.5.24 displays diagnostic information useful for network tuning and troubleshooting. The Diag tab is particularly helpful in coordinating serial data flow rates with RF packet delivery rates, and evaluating the robustness and stability of the RF link between this node and the rest of the network. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 61 of 75 LPR2430 - 06/23/09 Figure 5.5.25 The File drop-down menu is shown in Figure 5.5.25. This menu provides an alternate access to the Connect dialog window, allows the configuration of LPRDemo2 to be saved (not the module settings), plus a conventional Windows program Exit. Figure 5.5.26 The View drop down menu is shown in Figure 5.5.26. Enabling Show Comm Errors causes a dialog window to appear if the serial connection experiences an overrun, underrun, or framing error. Show Setting in Hex performs the same function at the F8 key for the WinCom terminal program, allowing received data to be shown as either hexadecimal or ASCII data. Log Data creates a log file of the communication between LPRDemo2 and the radio module. The log file name is logfile.dat, and is created in the same directory as LPRDemo2. The file is ASCII text. A sample of a logfile.dat is shown below: Sent Data : FB 08 A3 Recv Data : FB 06 A3 Sent Data : FB 08 A4 Recv Data : FB 06 A4 Sent Data : FB 07 A5 Recv Data : FB 35 A5 FF FF FF FF FF FF FF 00 00 00 (Get Remote 0B 01 00 1B 00 01 0B 01 00 1B 00 01 0A 01 00 1A 00 01 FF FF FF Register 02 05 01 00 (Set Remote Register) 00 58 (Set Remote Register Reply) 03 05 01 00 (Set Remote Register) 00 58 (Set Remote Register Reply) 00 00 2C (Get Remote Register) 00 58 00 00 2C 00 FF FF 00 64 00 00 00 64 00 00 02 FF FF FF FF FF FF 4C 50 52 32 34 33 30 00 00 00 00 00 00 Reply) Figure 5.5.27 The Options drop-down menu includes access to Packet Builder, as discussed in the text associated with Figures 5.5.6 through 5.5.9 above. The Diagnostics menu item provides one of two dialog windows, depending on whether the radio is operating as a base or a remote. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 62 of 75 LPR2430 - 06/23/09 Figure 5.5.28 The diagnostic window for the Base is shown in Figure 5.5.28 above. Checking a network address in the Poll column adds it to the diagnostic data. A logging option is provided to capture the diagnostic data. The name of the file is diagfile.dat. It is created in the same directory as LPRDemo2. Figure 5.5.29 The diagnostic window for a Remote is shown in Figure 5.5.29 above. A logging option is also provided to capture diagnostic data. The name of the file is diagfile.dat. It is created in the same directory as LPRDemo2. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 63 of 75 LPR2430 - 06/23/09 Figure 5.5.30 The Help drop-down menu provides an About item that shows the version number, etc., of LPRDemo2. Figure 5.5.31 Clicking the Upgrade button under the Base Current Settings data on the main LPRDemo2 window launches the Upgrade Firmware dialog base shown in Figure 5.5.31. Contact RFM module technical support before attempting an update. See Section 7.2. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 64 of 75 LPR2430 - 06/23/09 6.0 Troubleshooting LPR2430 series radio not responding - make sure the /RESET line is not asserted (logic low). Logic high brings the radio out of reset mode. Cannot enter protocol mode - make sure the host data rate is correct. LPR2430 series radios default to 9.6 kb/s. If using the EnterProtocolMode command, send the complete protocol format for this command. Range is extremely limited - this is usually a sign of a poor antenna connection or the wrong antenna. Confirm that the 50 ohm stripline connecting the radio to the antenna or antenna connector complies with Section 3.4. Check that the antenna is firmly connected. If possible, remove any obstructions near the antenna. www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 65 of 75 LPR2430 - 06/23/09 7.0 Appendices 7.1 Ordering Information LPR2430: 1 mW low current 802.15.4 module for solder reflow mounting LPR2430A: 1 mW low current 802.15.4 module with integral antenna for solder reflow mounting LPR2430ER: 63 mW high power 802.15.4 module for solder reflow mounting LPR2430ERA: 63 mW high power 802.15.4 module with integral antenna for solder reflow mounting 7.2 Technical Support For LPR2430 series module technical support call RFM at (678) 684-2000 between the hours of 8:30 AM and 5:30 PM Eastern Time www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 66 of 75 LPR2430 - 06/23/09 7.3 LPR2430 Series Mechanical Specifications L P R 2 4 3 0 O u tlin e a n d M o u n tin g D im e n s io n s 0 .8 0 .0 5 0 .0 4 1 5 1 0 .0 3 T o p V ie w 0 .9 8 5 1 6 3 0 0 .1 2 D im e n s io n s in in c h e s Figure 7.3.1 L P R 2 4 3 0 A O u tlin e a n d M o u n tin g D im e n s io n s 1 .0 5 0 .0 5 1 5 0 .0 4 0 .0 5 1 0 .0 3 T o p V ie w 1 6 0 .9 8 5 3 0 0 .1 2 D im e n s io n s in in c h e s Figure 7.3.2 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 67 of 75 LPR2430 - 06/23/09 L P R 2 4 3 0 E R O u tlin e a n d M o u n tin g D im e n s io n s 1 .2 0 .0 4 0 .0 5 1 5 1 0 .0 3 0 .9 8 5 T o p V ie w 1 6 3 0 0 .1 1 D im e n s io n s in in c h e s Figure 7.3.3 L P R 2 4 3 0 E R A O u tlin e a n d M o u n tin g D im e n s io n s 0 .3 0 1 .1 5 0 .0 4 0 .0 5 1 5 0 .0 3 1 1 6 0 .9 8 5 A n te n n a T o p V ie w 3 0 0 .1 2 0 .1 1 D im e n s io n s in in c h e s Figure 7.3.4 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 68 of 75 LPR2430 - 06/23/09 7.4 Developer Board Schematic, LPR2430A & LPR2430ERA Version www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 69 of 75 LPR2430 - 06/23/09 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 70 of 75 LPR2430 - 06/23/09 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 71 of 75 LPR2430 - 06/23/09 7.5 Developer Board Schematic, LPR2430 & LPR2430ER Version www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 72 of 75 LPR2430 - 06/23/09 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 73 of 75 LPR2430 - 06/23/09 www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 74 of 75 LPR2430 - 06/23/09 8.0 Warranty Seller warrants solely to Buyer that the goods delivered hereunder shall be free from defects in materials and workmanship, when given normal, proper and intended usage, for twelve (12) months from the date of delivery to Buyer. Seller agrees to repair or replace at its option and without cost to Buyer all defective goods sold hereunder, provided that Buyer has given Seller written notice of such warranty claim within such warranty period. All goods returned to Seller for repair or replacement must be sent freight prepaid to Seller's plant, provided that Buyer first obtain from Seller a Return Goods Authorization before any such return. Seller shall have no obligation to make repairs or replacements which are required by normal wear and tear, or which result, in whole or in part, from catastrophe, fault or negligence of Buyer, or from improper or unauthorized use of the goods, or use of the goods in a manner for which they are not designed, or by causes external to the goods such as, but not limited to, power failure. No suit or action shall be brought against Seller more than twelve (12) months after the related cause of action has occurred. Buyer has not relied and shall not rely on any oral representation regarding the goods sold hereunder, and any oral representation shall not bind Seller and shall not be a part of any warranty. THE PROVISIONS OF THE FOREGOING WARRANTY ARE IN LIEU OF ANY OTHER WARRANTY, WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL (INCLUDING ANY WARRANTY OR MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE). SELLER'S LIABILITY ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF THE GOODS OR THEIR USE OR DISPOSITION, WHETHER BASED UPON WARRANTY, CONTRACT, TORT OR OTHERWISE, SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY BUYER FOR THE GOODS. IN NO EVENT SHALL SELLER BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES ARISING OUT OF THE MANUFACTURE, SALE OR SUPPLYING OF THE GOODS. THE FOREGOING WARRANTY EXTENDS TO BUYER ONLY AND SHALL NOT BE APPLICABLE TO ANY OTHER PERSON OR ENTITY INCLUDING, WITHOUT LIMITATION, CUSTOMERS OF BUYERS. Part # M-2430-0002, Rev A www.RFM.com (c)2009 by RF Monolithics, Inc. Technical support +1.678.684.2000 E-mail: tech_sup@rfm.com Page 75 of 75 LPR2430 - 06/23/09