STANDARD
Resistive Touch Panel Specification
FID-550 7-Wire Series
■ PART NUMBERS
Touch Panels:
■ FEATURES
• Superior long life, using a unique construction method offering improved life over typical
technologies; by sensing data input only on the glass layer, typically a 10x improvement in
product life is achived.
• Excellent specification and high quality
- Anti-Newton ring technology
- High reliability materials
• Pen/Finger, Pen Only, Finger Only,
Light Touch types available
• Transparency 80% - typical
rebmuNtraPeziSepyT
203T-0150-010N"71regniF/neP
112T-0150-010N"51regniF/neP
319T-0550-010N"3.31regniF/neP
117T-0550-010N"1.21regniF/neP
242T-1550-010N"1.21)epythcuotthgil(regniF/neP
118T-0550-010N3.11regniF/neP
106T-0550-010N"4.01ylnoneP
116T-0550-010N"4.01regniF/neP
126T-0550-010N"4.01)epythcuotthgil(regniF/neP
115T-0550-010N"5.9regniF/neP
143T-0550-010N"4.8regniF/neP
Input Panel Panel Drive
change over
switch
Noise Filter
MCU
Control
Section
A/D
converter
Interface
■ PART NUMBERS
Controller Boards:
■ PART NUMBERS
Interface Controller Chips:
rebmuNtraPepyT
220V-9550-010N232SR,eriW-7
5100-02114CNBSU,eriW-7
rebmuNtraPepyT
042B-8550-B61N232SR,eriW-7
027B-8550-B61NBSU,eriW-7
2
FID-550 SERIES
AB
C
■ DETAILED SPECIFICATION
■ 1.0 APPLICATION
This specification applies to the 10.4" (inch) standard Touch Panel (Pen/Finger type). P/N is N010-0550-T611.
■ 2.0 ADDITIONAL APPLICATIONS
Control IC specifications and Control PCB, complete Touch Panel Specifications are also applicable.
■ 3.0 DISCRIPTION AND BLOCK DIAGRAM
This panel in combination with a control IC chip is used to transfer the co-ordinates of the touched position to
the host system (see block diagram above).
■ 4.0 DRAWING
(Please see the diagram above.)
Definitions of the major dimensions indicated on this diagram:
Effective Input Area (A) Area guaranteed to meet all the
characteristics detailed in this specification
View / Transparent Area (B) The area inside the adhesive zone
or electrode pattern.
Anti-input Area (C) An insulating area allowed to protect
the touch panel from giving false
readings when an enclosure touches
the panel.
■ 5.0 CHARACTERISTICS
■ 5.1 MECHANICAL
Operating Force 0.05~0.49 N (5 ~ 50gF) Measured with
a Silicon Measurement Rod R 8
(Round type 8mm) Silicon Rubber
Hardness 60˚C
Hardness of Surface Pencil hardness 3H minimum against
specification JIS K-5400
■ 5.2 OPTICAL
Transparency 78% min measured in the effective input area to JIS K 7105 using a
MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter. Typically 80%.
Haze 5% measured in the effective input area using a MURAKAMI
SHIKISAI KENKYUSHO type IIR 100 meter with an Anti Glare treated
surface.
Force
Silicon Rubber Rod
Unit: mm
93.70
123.75
(3.50)
162.40
215.10
213.10 (input area)
( )
16.00
Bottom
Left
Top
(8.00)
(
22.00
12.5
1
0.5
180.40
(
3.50
)
236.80
1
7
164.40 (transparent area)
(11.50)
217.10 (transparent area)
( )
187.40
( )
243.802.0
±
±
1.0
±
1.0
±
1.0
3.50
23.20
47.00
47.0 x 3=141.00
90.5
±
1.0
±
±
■ DIMENSION EXAMPLE (10.4” SHOWN)
3
FID-550 SERIES
■ 5.3 ELECTRICAL
Location Accuracy: ±2.5mm Measured over 9 points (See note 1)
Linearity: 1.5%
Current Consumption: 20mA max at DC 5V when applying 5VDC between pins 3 & 5
Switch Bounce (Chattering): 10ms min when using the silicon rubber measurement rod.
Insulation resistance: 10MΩ minimum at 25KV DC applied between pins 3 & 7 or
between 5 and 7
Dielectric Strength: 25KV DC for 1 minute
Note 1:
Measurement condition of linearity is corrected within the
control IC. In general the location accuracy is specified
as follows:
Actual co-ordinate point - theoretical co-ordinate point
= location accuracy.
In general a 9 point co-ordinate calibration system is used
to adjust the micro controller accuracy. (20 point can be
used in combination with an EEPROM design).
Note 2:
Pins 3, 5 and 7 are the glass and film connection points.
■ 5.4 ENVIRONMENTAL
Operating Temperature (*): -5˚C to 60˚C
Storage Temperature: -30˚C to 70˚C
Operating Humidity: 20% to 90% RH with a Maximum wet bulb temperature of 38˚C
Storage Humidity: 10% ~ 90% RH with a Maximum wet bulb temperature of 38˚C
Chemical Resistance: Coating with the following chemicals and storing at room temperature for 2
hours gives no problems. 10% NaCl-water solution, ethyl-acetate, ethyl-
alcohol, toluene, methyl-ethyl-ketone.
■ 5.5 PEN LIFE
Character Writing life: 1,000,000 words minimum
Touch Input life : 10,000,000 times minimum
Note 1:
Words are written in the notes area and the size of the word is
7.5mm x 6.75mm. A word is any Alphabet / Number / Mark.
The pen is as shown below and applies a force of 250g.
A failure is judged to happen when the current consumption or
insulation resistance or dielectric strength are not met as
shown in 5.3. The location accuracy with 9 point calibration
must be ±4.4 mm max.
9 mm
10 mm
Notes
Effective input area
Distance
Co-ordinate Point
Theoretical
Actual
Error
3.5
Ø6.0
Ø2.0
9.01.0
110.0±1.03.01.5
Ø 4.6
Ø 2.0
R 0.8
4
FID-550 SERIES
■ 5.6 FINGER LIFE
A finger is simulated by a silicon rubber plunger
R8 (Round type 8mm size) hardness 60˚C at 200g
at frequency 5Hz.
A failure is judged to happen when the current
consumption or insulation resistance or dielectric
strength are not met as shown in 5.3. The location
accuracy with 9 point calibration must be ±4.4 mm max.
Typical operating force is 150g max.
■ 5.7 INFORMATION ON THE PANEL
The panel part number is visible from the film side
The production information is visible from the glass side.
Production year 99 00 etc.
1 2 3 4 5 6 7 8 9 X Y Z or 1 2 3 4 5 6 7 8 9 X Y Z January Production
2 3 4 5 6 7 8 9 X Y Z or 2 3 4 5 6 7 8 9 X Y Z February Production
December Production
■ 6 PACKAGING
■ 6.1 PACKING SPECIFICATION
Vibration: 10~55 Hz at 1 Octave per minute 10G 20 cycles with one side 0.75mm
Drop test: 60cm Drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time
After the test no glass: flaw or crack is seen, and no dent or scratch on the film.
Also glass and film must not separate.
Z or 1 2 3 4 5 6 7 8 9 Y Z
■ 6.1 PACKING DETAILS
Each touch panel is placed into a plastic bag and is
held in place by a slit cut into the side of the card-
board. A second insertion piece is placed into the
carton to again add stability. The qty is written on
the side of the box. For example the T611 has 26
pieces per box. Insert
Touch panel with bag
Slit in cardboard
5
FID-550 SERIES
■ 7.0 REJECT CRITERIA
noitpircseDairetirCtcejeR
tneDmliF
mm1.0aerA
2
mm50.0aerA
2
mm1.0<aera&
2
mm50.0<aerA
2
orezebot:
stniop5.xamebot:
deificepsenon:
ngieroF
lairetam
neewteb
mlifdnassalg
epyttoD
mm1.0>aerA
2
mm50.0aerA
2
mm1.0<aera&
2
mm50.0<aerA
2
orezebot:
stniop5.xamebot:
deificepsenon:
epyteniL
mm1.0aerA mm01<htgneldnamm1.0<htdiw&mm30.0aerA
mm50.0<aerA
orezebot:
tniop1.xamebot:
deificepsenon:
hctarcS
mm1.0aerA mm08<htgnelhtiwmm1.0<htdiw&mm30.0aerA mm03<htgnelhtiwmm1.0<htdiw&mm30.0<aerA
orezebot:
tniop1.xamebot:
deificepsenon:
taocdrahrorulbtoD
gnissim
mm5.0aerA
2
mm30.0aerA
2
mm5.0<aera&
2
mm50.0<aerA
2
orezebot:
stniop5.xamebot:
deificepsenon:
gniRnotweN 3(pmaltnecseroulfarednuedismliflenaPmorfneesebtontsumesehT .edisssalgmrofdeifirevebottoN.)pmalepythtgnelevaw
walfssalG ehT.margaidgniwollofehtninwohstahtnahtreggibsihcihwwalfoneboT
.deificepstonsiswalfforebmun
■ 8.0 GENERAL POINTS OF CAUTION
Touch panels are made of glass, so care must be taken in handling them. Do not stress, pile, bend, lift by the
cable or put any stress on the film, for example moving by film face vacuum. In order to clean wring dry a
cloth which has been emersed in a natural detergent. DO NOT use any organic solvent, acid or alkali solu-
tion. Watch the edge of the panel when cleaning, again for safety reasons.
≥
≥
≥
≥
≥
≥
≥
≥
≥
2mm 2mm
5mm
3mm
6
FID-550 SERIES
■ 9.0 CONNECTION AND MOUNTING
The details below indicate the recommended mounting structure for panel and enclosure. The enclosure
support to fix the touch panel must be over 1.0mm I width and must be outside the view (Transparent area).
Also ensure that the enclosure does not cause miss input by touching the view area.
The following diagram shows that the enclosure edge must be between the View area and the guaranteed
active area. Ensure space is allocated for the diodes, and we recommend that the material to fix the panel
and enclosure is elastic. Special design would be required to stop water ingress. The corners of the touch
panel are conductive so do not touch any metal parts after mounting.
Location Detect
1. Right/ Upper Glass
2. Right/ Upper Glass
3. Each side Glass
4. Left/ Lower Glass
5. Each side Glass
6. Left/ Lower Glass
7. All Film
Bottom View (Drawing, with conductive side up)
(Mating connector type FCI or equivalent SFW15R-1ST: for FPC)
0.8 mm min.
Connector
LCD
1.0 to 3.0 mm
Circuit Board
Transparent Area
Anti-input Area
Shock absorber to protect
the panel (eg rubber)
Upper Case
Input Area
Shock absorber
for protection
View Area
Input PanelWiring Area
Cut-out / avoidance of
550 surface mount diodes
Conductive Face
FPC-type cableContact Section View
Laminate Film
Stiffener Board
0.3±0.05
2.0
1.1
1.2
0.73.35
2.0
Top View (Picture, with conductive
side down)
7
FID-550 SERIES
■ 10.0 PANEL THICKNESS
2.6 Max
1.4
Thickness of glass 1.1mm
Stiffener Board
Conductive Face
© 2005 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 05/09/2005.
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 375-8560
Fax: (65) 273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
Fujitsu Components
International
Headquarter
Offices