Enpirion(R) Power Datasheet EN5366QI 6A PowerSoC Voltage Mode Synchronous Buck PWM DC-DC Converter with Integrated Inductor External Output Voltage Programming Description Features This Altera Enpirion solution is a Power System on a chip (PowerSoC). It is specifically designed to meet the precise voltage and fast transient requirements of present and future highperformance, low-power processor, DSP, FPGA, ASIC, memory boards and system level applications in a distributed power architecture. Advanced circuit techniques, ultra high switching frequency, and very advanced, high-density, integrated circuit and proprietary inductor technology deliver high-quality, ultra compact, non-isolated DC-DC conversion. Operating this converter requires as few as three external components that include small value input and output ceramic capacitors and a soft-start capacitor. * * * * * * * * * * * * * * The Altera Enpirion integrated inductor solution significantly helps in low noise system design and productivity by offering greatly simplified board design, layout and manufacturing requirements. * All Altera Enpirion products are RoHS compliant and lead-free manufacturing environment compatible. Typical Application Circuit VIN PVIN 47F 1 VOUT AVIN ENABLE PGND 47F XOV XFB Applications * * * * * * * Point of load regulation for low-power processors, network processors, DSPs, FPGAs, and ASICs 90 nm advanced process loads Notebook computers, servers, workstations Broadband, networking, LAN/WAN, optical Low voltage, distributed power architectures with 2.5V, 3.3V or 5V rails DSL, STB, DVR, DTV, Industrial PC Ripple sensitive applications Ordering Information SS 15nF AGND VOUT Integrated INDUCTOR, MOSFETS, Controller Footprint 1/3rd that of competing solutions. Low Part Count: only 3 MLCC Capacitors. Up to 20W continuous output power. Low output impedance optimized for 90 nm Master/slave configuration for paralleling. 5MHz operating frequency. High efficiency, up to 93%. Wide input voltage range of 2.375V to 5.5V. External resistor divider output voltage select. Output enable pin and Power OK signal. Programmable soft-start time. Optimized for low noise/EMI design. Under-Voltage Lockout, Thermal Shutdown, Output Overvoltage, Over Current, and Short Circuit Protection RoHS compliant, MSL level 3, 260C reflow. PGND Figure 1. Simple Schematic Part Number EN5366QI EVB-EN5366QI Temp Rating (C) Package -40 to +85 58-pin QFN T&R QFN Evaluation Board *Optimized PCB Layout file downloadable from www.altera.com/enpirion to assure first pass design success. 03817 October 11, 2013 Rev E EN5366QI Pin Configuration Below is a top view diagram of the EN5366Q package. NOTE: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. Figure 2. Pin Diagram, top view. 2 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Pin Descriptions PIN NAME 1-3 NC 4-5 NC(SW) 6-13 NC 14-20 VOUT 21-22 NC(SW) 23 NC 24-29 PGND 30-35 PVIN 36-37 NC 38 ROCP 39 AVIN 40 AGND 41-42 NC 43 44 XFB XOV 45 NC 46 POK 47 NC 48 SS 49 50 51 EAIN EAOUT COMP FUNCTION NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. NO CONNECT - These pins are internally connected to the common drain output of the internal MOSFETs. NC(SW) pins are not to be electrically connected to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Regulated converter output. Decouple with output filter capacitor to PGND. Refer to layout section for specific layout requirements NO CONNECT - These pins are internally connected to the common drain output of the internal MOSFETs. NC(SW) pins are not to be electrically connected to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Output power ground. Refer to layout section for specific layout requirements. Input power supply. Connect to input power supply. Decouple with input capacitor to PGND. Refer to layout section for specific layout requirements NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Optional Over Current Protection adjust pin. Used for diagnostic purposes only. Place 10k resistor between this pin and AGND (pin 40) to raise the over current trip point to approximately 200% of maximum rated current. Analog voltage input for the controller circuits. Connect this pin to PVIN using a 1 Ohm resistor. Analog ground for the controller circuits. NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Feedback pin for external voltage divider network. Over voltage programming feedback pin. NO CONNECT: This pin should not be electrically connected to any other NC pin, or to any external signal, voltage, or ground. This pin may be connected internally. Power OK is an open drain transistor for power system state indication. POK is a logic high when VOUT is with -10% to +20% of VOUT nominal. Size pull-up resistor to limit current to 4mA when POK is low. NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Soft-Start node. The soft-start capacitor is connected between this pin and AGND. The value of this capacitor determines the startup timing. Optional Error Amplifier input. Allows for customization of the control loop. Optional Error Amplifier output. Allows for customization of the control loop. Optional Error Amplifier Buffer output. Allows for customization of the control loop. 3 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI PIN NAME FUNCTION 52 ENABLE 53 PWM 54 NC 55 M/S 56-58 NC Input Enable. Applying a logic high, enables the output and initiates a soft-start. Applying a logic low disables the output. PWM input/output. Used for optional master/slave configuration. When M/S pin is asserted "low", PWM will output the gate-drive PWM waveform. When the M/S pin is asserted "high", the PWM pin is configured as an input for PWM signal from the "master" device. PWM pin can drive up to 3 slave devices. NOTE: Leave this pin open when not using parallel mode. NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Optional Master/Slave select pin. Asserting pin "low" places device in Master Mode for current sharing. PWM pin (53) will output PWM drive signal. Asserting pin "high" will place the device in Slave Mode. PWM pin (53) will be configured to input (receive) PWM drive signal from "Master" device. NOTE: Leave this pin open when not using parallel mode. NO CONNECT: These pins should not be electrically connected to each other or to any external signal, voltage, or ground. One or more of these pins may be connected internally. Block Diagram POK PVIN power Good Logic UVLO Thermal Limit ROCP Current Limit Over Voltage VOUT Over Voltage XOV NC(SW) P-Drive VOUT (-) N-Drive PWM Comp (+) PGND Compensation Network Sawtooth Generator Voltage Selector (-) Error Amp (+) ENABLE SS XFB Reference Voltage selector Soft Start Bandgap Reference EAIN EAOUT COMP Figure 3. System block diagram. 4 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Absolute Maximum Ratings CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond recommended operating conditions is not implied. Stress beyond absolute maximum ratings may cause permanent damage to the device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. PARAMETER SYMBOL MIN MAX UNITS VIN -0.5 -0.5 -0.5 -0.5 -0.5 -0.5 -65 7.0 VIN 2.5 2.5 3.0 VIN + 0.3 150 260 2000 V V V V V V C C V Input Supply Voltage Voltages on: ENABLE, Voltage on XFB, XOV Voltages on: EAIN, EAOUT, COMP Voltages on: SS, PWM Voltages on: POK Storage Temperature Range Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020A ESD Rating (based on Human Body Model) TSTG Recommended Operating Conditions PARAMETER Input Voltage Range Output Voltage Range Operating Ambient Temperature Operating Junction Temperature SYMBOL MIN MAX UNITS VIN VOUT TA TJ 2.375 0.75 -40 -40 5.5 3.3 +85 +125 V V C C SYMBOL TYP UNITS 20 1.5 +150 20 C/W C/W C C Thermal Characteristics PARAMETER Thermal Resistance: Junction to Ambient (0 LFM) (Note 1) Thermal Resistance: Junction to Case (0 LFM) Thermal Overload Trip Point Thermal Overload Trip Point Hysteresis JA JC TJ-TP NOTES: 1. Based on a four-layer board and proper thermal design in line with JEDEC EIJ/JESD 51 Standards. 5 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Electrical Characteristics NOTE: VIN=5.5V over operating temperature range unless otherwise noted. Typical values are at TA = 25C. PARAMETER SYMBOL Input Voltage Output Regulation VIN Feedback Pin Voltage VOUT Feedback Pin Voltage VOUT TEST CONDITIONS MIN TYP 2.375 2.375V VIN 5.5V, ILOAD = 1A; T A = 25C 2.375V VIN 5.5V, 0A ILOAD 6A -40 C T A +85 C Transient Response (IOUT = 0% to 100% or 100% to 0% of Rated Load) VIN = 5V, 1.2V < VOUT < 3.3V Peak Deviation VOUT COUT=50uF Under Voltage Lockout Under Voltage Lock VIN Increasing VUVLO out threshold VIN Decreasing Switching Frequency Switching F SWITCH Frequency Load Characteristics Maximum Continuous Output IOUT (Note 2) Current Current Limit IOCP_TH Threshold Supply Current Shut-Down Supply IS ENABLE=0V Current MAX UNITS 5.5 V 0.735 0.750 0.765 V 0.725 0.750 0.773 V 3 % 2.2 2.1 V 5 MHz 6 A 9 A 50 A Enable Operation Disable Threshold VDISABLE Enable Threshold Enable Pin Current VENABLE IEN Max voltage to ensure the converter is disabled 2.375V VIN 5.5V VIN = 5.5V 6 03817 October 11, 2013 0.8 1.8 50 V V A www.altera.com/enpirion Rev E EN5366QI PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS 0.8 V VIN V Voltage Select Operation Logic Low Threshold VSX-Low Logic High Threshold Threshold voltage for Logic Low Threshold voltage for Logic High (internally pulled high; can be left floating to achieve logic high) VIN = 5.5V VSx = GND VSx = VIN VSx = Open VSX-High VSx Pin Current IVSX 1.8 50 0 0 A 120 90 0.4 VIN % % V % +25 % Power OK Operation (Open Drain) POK threshold High POK threshold low POK Low Voltage POK High Voltage Output Rise Time Percentage of VOUT Nominal Percentage of VOUT Nominal IPOK = 4 mA (Max sink Current) VOUT Rise Time Accuracy TRISE = Css* 75K; 10nF CSS 30nF T RISE -25 (Note 3) Parallel Operation With 2 - 4 converters in parallel, the difference between any 2 parts. VIN < 50mV; RTRACE < 10m. IOUT Current Balance +/-10 % NOTES: 2. Maximum output current may need to be de-rated, based on operating condition, to meet TJ requirements. 3. Parameter not production tested but is guaranteed by design. Rise time begins when AVIN > V UVLO and Enable=HIGH. Typical Performance Characteristics 95 95 90 VOUT=3.3V 85 VOUT=2.5V VOUT=2.5V 85 VOUT=1.8V 80 VOUT=1.5V 75 VOUT=1.2V 70 VOUT=1.8V 80 Efficiency (%) Efficiency (%) 90 VOUT=1.5V 75 VOUT=1.2V 70 65 65 60 60 55 55 VIN=5.0V VIN=3.3V 50 50 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 0 0.5 2 2.5 3 3.5 4 4.5 5 5.5 Efficiency vs. Load, VIN = 5.0V.; Load = 0-6A. 7 03817 1.5 Load Current (A) Load Current (A) Efficiency vs. Load, VIN = 3.3V.; Load = 0-6A. 1 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Ripple Voltage, 5.0VIN/1.2VOUT, IOUT=6A, COUT = 3x22uF. Ripple Voltage, 3.3VIN/1.2VOUT, IOUT=6A, COUT = 3x22uF. Transient Response 5.5VIN/1.2VOUT, 0-6A, 10A/uS. COUT=50uF. Transient Response 5.5VIN/3.3VOUT, 0-6A, 10A/uS. COUT=50uF Start up waveforms VIN=5.0V, VOUT=1.2V, CSS=15nF, Ch 1 = VOUT, Ch 3 = ENABLE, Ch 4 = POK. Start up waveforms VIN=5.0V, VOUT=3.3V, CSS=15nF, Ch 1 = VOUT, Ch 3 = ENABLE, Ch 4 = POK. 8 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Theory of Operation Synchronous Buck Converter The EN5366 is a synchronous, programmable power supply with integrated power MOSFET switches and integrated inductor. The nominal input voltage range is 2.4-5.5V. The output voltage is programmed using an external resistor divider network. The feedback control loop is a type III voltage-mode and the part uses a lownoise PWM topology. Up to 6A of continuous output current can be drawn from this converter. The 5MHz operating frequency enables the use of small-size input and output capacitors. The power supply has the following protection features: * Programmable over-current protection (to protect the IC from excessive load current). * Short Circuit protection. * Thermal shutdown with hysteresis. * Programmable over-voltage protection. * Under-voltage lockout circuit to disable the converter output when the input voltage is less than approximately 2.2V values be ~2k. Use the following equation to set the resistor Ra1 for the desired output voltage: (Vout - 0.75V ) * Rb1 0.75V Ra1 = If over-voltage protection is desired, use the following equation to set the resistor Ra2 for the desired OVP trip-point: Ra 2 = (OVPtrip - 0.90V ) * Rb2 0.90V By design, if both resistor dividers are the same, the OV trip-point will be 20% above the nominal output voltage. VIN PVIN POK VOUT VOUT Ra2 47F Ra1 XOV AVIN 47F XFB SS Rb2 CSS AGND Rb1 PGND Additional features include: * * Figure 4. VOUT and OVP resistor divider networks. Soft-start circuit, to limit the in-rush current when the converter is powered up. Power good circuit (POK) indicating whether the output voltage is between 90% of nominal VOUT and the OVP trip point. Output Voltage Programming The EN5366 output voltage is programmed using a simple resistor divider network. Figure 4 shows the resistor divider configuration. The EN5366 output voltage and over voltage thresholds are determined by the voltages presented at the XFB and XOV pins respectively. These voltages are set by way of resistor dividers between VOUT and AGND with the midpoint going to XFB and XOV. Input Capacitor Selection The EN5366QI requires about 40-50uF of input capacitance. Low ESR ceramic capacitors are required with X5R or X7R dielectric formulation. Y5V or equivalent dielectric formulations must not be used as they lose capacitance with frequency, temperature and bias voltage. In some applications, lower value ceramic capacitors maybe needed in parallel with the larger capacitors in order to provide high frequency decoupling. Recommended Input Capacitors. Description 22uF, 10V, X5R, 1206 (2 capacitors needed) MFG Murata Taiyo Yuden P/N GRM31CR61A226ME19L LMK316BJ226ML-T It is recommended that Rb1 and Rb2 resistor 9 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI 47uF, 10V, X5R, 1210 (1 capacitor needed) Murata GRM32ER61A476KE20L Taiyo Yuden LMK325BJ476MM-T Output Capacitor Selection The EN5366QI has been optimized for use with approximately 50F of output capacitance. Low ESR ceramic capacitors are required with X5R or X7R dielectric formulation. Y5V or equivalent dielectric formulations must not be used as these lose capacitance with frequency, temperature and bias voltage. Recommended Output Capacitors. Description 22uF, 6.3V, 10% X5R, 1206 (3 capacitors needed) 47uF, 10V, 10% X5R, 1210 47uF, 6.3V, 10% X5R, 1210 (1 capacitor needed) MFG Murata P/N GRM31CR60J226KE19L Taiyo Yuden JMK316BJ226KL-T Murata GRM32ER61A476KE20L AVX 12106D476KAT2 Output ripple voltage is primarily determined by the aggregate output capacitor impedance. At the 5MHz switching frequency output impedance, denoted as Z, is comprised mainly of effective series resistance, ESR, and effective series inductance, ESL: Z = ESR + ESL. Placing output capacitors in parallel reduces the impedance and will hence result in lower ripple voltage. 1 Z Total = 1 1 1 + + ... + Z1 Z 2 Zn the use of a type 3 compensation network and is optimized for use with about 50F of output capacitance and will provide excellent loop bandwidth and transient performance for most applications. Voltage mode operation provides high noise immunity at light load. Further, Voltage mode control provides superior impedance matching to sub 90nm loads. In some cases modifications to the compensation may be required. The EN5366QI provides the capability to modify the control loop to allow for customization for a given application. For more information, contact Altera Power Applications support. Enable Operation The ENABLE pin provides a means to shut down the device, or enable normal operation. A logic low will disable the converter and cause it to shut down. A logic high will enable the converter into normal operation. When the ENABLE pin is asserted high, the device will undergo a normal soft start. Soft-Start Operation The SS pin in conjunction with a small capacitor between this pin and AGND provides the soft start function to limit the in-rush current during start-up. During start-up of the converter the reference voltage to the error amplifier is gradually increased to its final level by an internal current source of typically 10uA charging the soft start capacitor. The typical soft-start time for the output to reach regulation voltage, from when AVIN > VUVLO and Enable crosses its logic high threshold, is given by: TSS = CSS * 75K (seconds) Typical ripple versus capacitor arrangement is given below: Output Ripple vs Capacitor Configuration. Output Capacitor Configuration 1 x 47uF 3 x 22 uF Typical Output Ripple (mVp-p) (as measured on EN5366QI Evaluation Board) 30 15 Compensation The EN5366 is internally compensated through Where the soft-start time TSS is in seconds and the soft-start capacitance CSS is in Farads. Typically, a capacitor of around 15nF is recommended. During the soft-start cycle, when the soft-start capacitor reaches 0.75V, the output has reached its programmed regulation range. Note that the soft-start current source will continue to operate, and during normal operation, the soft-start capacitor will charge up to a final value of 2.5V. 10 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI POK Operation The POK signal is an open drain signal from the converter indicating the output voltage is within the specified range. The POK signal will be a logic high when the output voltage is within 90% 120% of the programmed output voltage. If the output voltage goes outside of this range, the POK signal will be a logic low until the output voltage has returned to within this range. In the event of an over-voltage condition the POK signal will go low and will remain in this condition until the output voltage has dropped to 95% of the programmed output voltage before returning to the high state. POK signal goes low. When the output voltage drops below 95% of the programmed output voltage, normal PWM operation resumes and POK returns to its high state. Thermal Overload Protection Thermal shutdown will disable operation when the Junction temperature exceeds approximately 150C. Once the junction temperature drops by approx 20C, the converter will re-start with a normal soft-start. Input Under-Voltage Lock-Out The internal POK FET is designed to tolerate up to 4mA. The pull-up resistor value should be chosen to limit the current from exceeding this value when POK is logic low. Circuitry is provided to ensure that when the input voltage is below the required voltage level (VUVLO) for normal operation, the converter will not start-up. Circuits for hysteresis and input deglitch are included to ensure high noise immunity and to prevent false tripping. Over-Current Protection Parallel Device Operation The current limit function is achieved by sensing the current flowing through a sense P-MOSFET. When the sensed current exceeds the current limit, both NFET and PFET switches are turned off. If the over-current condition is removed, the over-current protection circuit will re-enable the PWM operation. If the over-current condition persists, the circuit will continue to protect the load. The EN5366QI is capable of paralleling up to a total of four converters to provide up to 24A of continuous current. Please consult Paralleling Circuit Design with EN5365/66 for more details and recommendations. The OCP trip point is nominally set to 150% of maximum rated load. For diagnostic purposes, it is possible to increase the OCP trip point to approximately 200% of the maximum rated load by connecting a 10k resistor between the ROCP pin (pin 38) and AGND (pin 39). This is intended for troubleshooting purposes only and the specification is not guaranteed. Over-Voltage Protection When the output voltage exceeds 120% of the programmed output voltage, the PWM operation stops, the lower N-MOSFET is turned on and the Power-Up/Down Sequencing During power-up, ENABLE should not be asserted before PVIN, and PVIN should not be asserted before AVIN. The PVIN should never be powered when AVIN is off. During power down, the AVIN should not be powered down before the PVIN. Tying PVIN and AVIN or all three pins (AVIN, PVIN, ENABLE) together during power up or power down meets these requirements . Pre-Bias Start-up The EN5366QI does not support startup into a pre-biased condition. Be sure the output capacitors are not charged or the output of the EN5366QI is not pre-biased when the EN5366QI is first enabled. 11 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Layout Recommendations Compensation Test Points AGND Test Points High-Frequency Noise Suppression Vias VOUT(+) Copper Local Ground Copper Thermal Pad Vias and Soldermask Opening VIN(+) Copper Vout Slit separating input local ground from output local ground PGND Copper Slit Vin Figure 5. Layout of power and ground copper. Figure 6. Use of thermal & noise suppression vias. Recommendation 1: Input and output filter capacitors should be placed as close to the EN5366QI package as possible to reduce EMI from input and output loop currents. This reduces the physical area of the Input and Output AC current loops. These vias can be the same size as the thermal vias discussed in recommendation 3. Recommendation 5: The system ground plane referred to in recommendations 3 and 4 should be the first layer immediately below the surface layer. This ground plane should be continuous and un-interrupted below the converter and the input/output capacitors shown in figure 6. Recommendation 2: Place a slit in the input/output capacitor ground copper starting just below the common connection point of the device GND pins as shown in figures 5 and 6. Recommendation 6: As with any switch-mode DC/DC converter, do not run sensitive signal or control lines underneath the converter package. Recommendation 3: The large thermal pad underneath the component must be connected to the system ground plane through as many vias as possible. The drill diameter of the vias should be less than 0.33mm, and the vias must have at least 1 oz. copper plating on the inside wall, making the finished hole size around 0.26mm. This connection provides the path for heat dissipation from the converter. Please see figures 6, 7, and 8. Please refer to the Gerber files and summarized layout notes available at www.altera.com/enpirion for more layout details. NOTE: Figures 5 and 6 show only the critical components and traces for a minimum footprint layout. ENABLE, Vout-programming, and other small signal pins need to be connected and routed according to the specific application. Recommendation 4: Multiple small vias should be used to connect ground terminal of the input capacitor and output capacitors to the system ground plane as shown in figure 6. 12 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Design Considerations for Lead-Frame Based Modules Exposed Metal on Bottom Of Package Lead frame offers many advantages in thermal performance, in reduced electrical lead resistance, , and in overall foot print. However, they do require some special considerations. In the assembly process lead frame construction requires that, for mechanical support, some of the lead-frame cantilevers be exposed at the point where wire-bond or internal passives are attached. This results in several small pads being exposed on the bottom of the package. Only the large thermal pad and the perimeter pads are to be mechanically or electrically connected to the PC board. The PCB top layer under the EN5366QI should be clear of any metal except for the large thermal pad. The "grayed-out" area in Figure 7 represents the area that should be clear of any metal (traces, vias, or planes), on the top layer of the PCB. Figure 8 demonstrates the recommended PCB footprint for the EN5366QI. Figure 9 shows the shape and location of the exposed metal pads as well as the mechanical dimension of the large thermal pad and the pins. Ground copper my extend under this pad. However, DO NOT CONNECT (NC) Figure 7. Lead-Frame exposed metal. Grey area highlights exposed metal that is not to be mechanically or electrically connected to the PCB. 13 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Figure 8: EN5366QI PCB Footprint (Top View) The solder stencil aperture for the thermal pad is shown in blue and is based on Enpirion power product manufacturing specifications. 14 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Package Dimensions Figure 9. Package dimensions. 15 03817 October 11, 2013 www.altera.com/enpirion Rev E EN5366QI Contact Information Altera Corporation 101 Innovation Drive San Jose, CA 95134 Phone: 408-544-7000 www.altera.com (c) 2013 Altera Corporation--Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. 16 03817 October 11, 2013 www.altera.com/enpirion Rev E Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Altera: EN5366QI EVB-EN5366QI