Technical Document LCD Specification LCD Group LQ035Q7DH07 LCD Module Product Specification October 2009 240 x 320 Portrait-mode Transflective QVGA LCD Module featuring 270 nits brightness in Transmissive mode, with contrast ratios of 80:1 in Transmissive mode, and 3:1 in reflective mode. Full specification listing. RECORDS OF REVISION LQ035Q7DH07 SPEC No. DATE PAGE SUMMARY NOTE LD-21910A Oct.2.2009 - - 1 st Issue LD-21910A-1 NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs, such as: *Personal computers *Office automation *Telecommunication equipment *Test and measurement equipment *Industrial control *Audio visual and multimedia equipment *Consumer electronics *PDA The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: *Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) *Traffic signals *Gas leakage sensor breakers *Alarm equipment *Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: *Military and space applications *Nuclear power control equipment *Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. LD-21910A-2 (1) Application This specification applies to LQ035Q7DH07 (2) Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor), named AD-TFT (Advanced TFT). It is practicable in both transmissive-type and reflection-type modes. It is composed of a color TFT-LCD panel, driver ICs, an FPC, a back light, and a back sealed casing. It isn't composed control circuit. Graphics and texts can be displayed on a 240x3x320 dots panel with 262,144 colors by supplying. Optimum view angle is 6 o'clock. An inverted display mode is selective in the vertical or the horizontal direction. (3) Mechanical specifications Table 1 Parameter Specifications Units Screen size (Diagonal) 8.9 [3.52"] Diagonal cm Display active area 53.64(H)x71.52(V) mm 240(H)x320(V) pixels Pixel format Remarks (1 pixel = R+G+B dots) Pixel pitch 0.2235(H)x0.2235(V) Pixel configuration mm R,G,B vertical stripe Unit outline dimension 65.0(W)x86.2(H)x3.2(D) mm Mass 34 g Surface hardness 3H Note 3-1 Excluding protrusion, including FPC cover portion For detailed measurements and tolerances, please refer to Fig. 1. (4) Pixel configuration (240,1) RGB (1,1) Display area FPC (1,320) (240,320) Note3-1 Typ. LD-21910A-3 (5) Input/Output terminal 5-1) TFT-LCD panel driving section Recommendation CNHIROSE FH12A-50S-0.5SH(55) or FH12-50S-0.5SH(55) Table2 Pin No. Symbol I/O 1 VL1 I 2 NC - 3 VL2 4 Description Remarks Power supply for LED (High voltage) I Power supply for LED (Low voltage) VEE - Power supply of gate driver(low level) 5 VSHD - Power supply of digital 6 DGND - Ground(digital) 7 CLS I Clock signal of gate driver 8 DGND - Ground(digital) 9 SPS I Start signal of gate driver 10 U/L I Selection for vertical scanning direction Note5-1 11 MOD I Control signal of gate driver Note5-2 12 VDD - Power supply of gate driver(high level) 13 VCOM I Common electrode driving signal 14 DGND - Ground(digital) 15 SPR I/O 16 DGND - Ground(digital) 17 VSHA - Power supply(analog) 18 LBR I Selection for horizontal scanning direction 19 PS I Power save signal Sampling start signal Note5-3 (Please don't carry out use by "Low" fixation) 20 REV I reverse control signal 21 DGND - Ground(digital) 22 B5 I BLUE data signal(MSB) 23 B4 I BLUE data signal 24 B3 I BLUE data signal 25 B2 I BLUE data signal 26 B1 I BLUE data signal 27 B0 I BLUE data signal(LSB) 28 LP I Data latch signal of source driver 29 DGND - Ground(digital) 30 SPL I/O 31 DGND - Ground(digital) 32 DCLK I Data sampling clock signal 33 DGND - Ground(digital) 34 G5 I GREEN data signal(MSB) 35 G4 I GREEN data signal 36 G3 I GREEN data signal 37 G2 I GREEN data signal 38 G1 I GREEN data signal 39 G0 I GREEN data signal(LSB) Sampling start signal Note5-4 LD-21910A-4 Pin No. Symbol I/O Description Remarks 40 DGND - Ground(digital) 41 R5 I RED data signal(MSB) 42 R4 I RED data signal 43 R3 I RED data signal 44 R2 I RED data signal 45 R1 I RED data signal 46 R0 I RED data signal(LSB) 47 AGND - Ground(analog) 48 COM O Produce REV signal with the amplitude of AGND-VSHA 49 DGND - Ground(digital) 50 DGND - Ground(digital) Note5-4 Note5-1Selection for vertical scanning direction U/L Scanning direction (Pixel configuration) Low Normal scanning ( X , 1 ) ( X , 320 ) High Inverted scanning ( X , 1) ( X , 320) Note5-2See section(7-1)-(A) " Cautions when you turn on or off the power supply". Note5-3Selection for horizontal scanning direction LBR SPL SPR Scanning direction (Pixel configuration) High Input Output Normal scanning (1,Y) (240,Y) Low Output Input Inverted scanning (1,Y) (240,Y) Note5-4 REV(IN) "" "" "" VSHA COM(OUT) AGND VCOM(IN) "" LD-21910A-5 (6)Absolute Maximum Ratings Table 3 Parameter Symbol Condition Ratings Unit Power supply(source/Analog) VSHA Ta=25C -0.3 to +7.0 V Power supply(source/Digital) VSHD Ta=25C -0.3 to +7.0 V Power supply (gate) VDD Ta=25C -0.3 to +35.0 V Power supply (gate) VDD - VEE Ta=25C -0.3 to +35.0 V VID Ta=25C -0.3 to VSHD+0.3 V Topp - -10 to +70 C Tstg - -25 to +70 C Input voltage (Digital) Operating temperature (panel surface) Storage temperature Remark [Terminal A] Note6 Note6 [Terminal A] MOD,U/L,SPS,CLS,SPL,R0 to R5,G0 to G5,B0 to B5,LP,DCLK,LBR,SPR,PS,REV Note6Humidity: 95%RH Max.(at Ta 40C). Maximum wet-bulb temperature is less than 39C (at Ta > 40C). 70 60 50 40 30 20 10 Humidity guarantee range Wet-bulb temperature:39 100 80 60 40 20 0 0 Relative humidity[%] Condensation of dew must be avoided. Circumference temperature[] The maximum humidity in the temperature LD-21910A-6 (7)Electrical characteristics 7-1) Recommended operating conditions A) TFT-LCD panel driving section Table 4 GND=0V Parameter Symbol Min. Typ. Max. Unit Supply voltage for source driver (Analog) VSHA +4.5 +5.0 +5.5 V Supply voltage for source driver (Digital) VSHD +3.0 +3.3 +3.6 V Supply voltage for gate driver High voltage VDD +14.5 +15.0 +15.5 V Low voltage VEE -10.5 -10.0 -9.5 V Input voltage for Source driver (Low) VILS GND - 0.2VSHD V Note 7-1 Input voltage for Source driver (High) VIHS 0.8VSHD - VSHD V Note 7-1 Input current for Source driver (Low) IILS - - 30 A Note 7-1 IIHS1 - - 30 A Note 7-2 IIHS2 - - 1200 A Note 7-3 Input voltage for Gate driver (Low) VILG GND - 0.2VSHD V Note 7-4 Input voltage for Gate driver (High) VIHG 0.8VSHD - VSHD V Note 7-4 Input current for Gate driver (Low) IILG - - 4 A Note 7-4 Input current for Gate driver (High) IIHG - - 4 A Note 7-4 AC component VCOMAC - 2.5 2.6 VP-P Note 7-5 DC component VCOMDC -0.8 +0.2 +1.2 Input current for Source driver (High) Common electrode driving signal Remarks Note 7-5 V Cautions when you turn on or off the power supply Turn on or off the power supply with simultaneously or the following sequence. The input signal of "MOD" Terminals (Pin No.11) must be low voltage when turning on the power supply, and it is held until more than double vertical periods after DATA are turned on completely. After then, it must be held high voltage until turning off the power supply. (Connect Pin No.11 terminals to the same signal.) VDD 90% VSHA 90% VSHD 90% GND 90% 10% 10% 0T2 0T3 0T1 0T4 VEE 0T7 0T5 90% 0T6 DATA 0T8 90% GND 10% 10% MOD 2VTmod GND 10% 10% Note 7-1DCLK,SPL,SPR,LBR,LP,PS,REV,R0 to R5,G0 to G5 and B0 to B5 terminals are applied. Note 7-2DCLK,SPL,SPR,LBR,LP,REV,R0 to R5,G0 to G5 and B0 to B5 terminals are applied. Note 7-3PS terminal is applied. Note 7-4MOD,CLS,SPS and U/L terminals are applied. Note 7-5VCOMAC should be alternated on VCOMDC every 1 horizontal period and 1 vertical period. VCOMDC bias is adjusted so as to minimize flicker or maximum contrast every each module. LD-21910A-7 B) Back light driving section Table 5 Ta=25C Parameter Symbol MIN TYP MAX Units LED voltage VL - 19.2 21.6 V LED current IL - 20 22 mA WL - 0.384 - W Power consumption Remarks terminal Note 7-6 Note 7-6Calculated reference value(ILxVL) 7-2) Timing Characteristics of input signals (VSHA=+5V, VSHD=+3.3V, Ta=25C) Table 6 AC Characteristics (1) Parameter Symbol Min. Typ. Max. Unit Clock frequency of source driver fCK 4.5 - 6.8 MHz Rising time of clock Tcr - - 20 ns Falling time of clock Tcf - - 20 ns Pulse width (High level) Tcwh 40 - - ns Pulse width (Low level) Tcwl 40 - - ns Frequency of start pulse fsp 16.5 - 28 kHz Setup time of start pulse Tsusp 15 - - ns Hold time of start pulse Thsp 10 - - ns Pulse width of start pulse Twsp - - 1.5/fCK ns Setup time of latch pulse Tsulp 20 - - ns Hold time of latch pulse Thlp 20 - - ns Pulse width of latch pulse Twlp 60 - - ns Setup time of PS Tsups 0 - - s Setup time of PS Tsulps 1 - - s Hold time of PS Thps 0 - - s Hold time of PS Thlps 30 - - ns Set up time of data Tsud 15 - - ns R0 to R5,G0 to G5 Hold time of data Thd 10 - - ns ,B0 to B5 fcls 16.5 - 28 kHz Pulse width of clock(Low) Twlcls 5 - (1/fcls)-30 s Pulse width of clock(High) Twhcls 30 - - s Rising time of clock Trcls - - 100 ns Falling time of clock Tfcls - - 100 ns Gate Setup time of clock Tsucls 3 - - s driver Hold time of clock Thcls 0 - - s Frequency of start pulse fsps 58 - 86 Hz Setup time of start pulse Tsusps 100 - - ns Hold time of start pulse Thsps 300 - - ns Rising time of start pulse Trsps - - 100 ns Falling time of start pulse Tfsps - - 100 ns Setup time of Vcom Tsuvcom 0 - - s Hold time of Vcom Thvcom 1 - - s Source driver Clock frequency Vcom Remark DCLK SPL, SPR Note 7-7 LP PS CLS SPS Vcom Note 7-7There must be only one up-edge of DCLK (includes Tsusp and Thsp time) in the period of SPL="Hi". Tch 80% DCLK Tcr 80% 1 20% Twlp 80% 20% 2 240 Tcwl Tcwh Twlp Thlp LP Tsulp Tsusp Thsp SPL Twsp Tsud Thd R0 to R5 G0 to G5 (1,n) (2,n) (1,n+1) (240,n) B0 to B5 Twh Thcls Tsucls CLS Twl Tsups Thps PS Tsulps Thvcom Thlps Tsuvcom VCOM 1 fcls 8 A 0 1 9 1 2 D L Fig.(a) Horizontal timing chart Trcls Twhcls Tfcls Twlcls 80% CLS 20% 80% SPS Tfsps 20% Tsusps 20% 1 20% Thsps 2 80% 20% 8 9 327 1 2 80% 20% Trsps 1 fsps R0 to R5 B0 to B5 Non-display period (1240,1) LINE1 (1240,2) (1240,320) LINE2 LINE320 Non-display period Fig.(b) Vertical timing chart 9 A 0 1 9 1 2 D L G0 to G5 LD-21910A-10 7-3) Power consumption Measurement condition: SPS=60Hz, CLS=15.73kHz, SPL=15.73kHz, DCLK=6.3MHz The term of PS="Lo" in one horizontal period ... 37sec (234DCLK) Ta=25C Table 7 when normal scan mode Parameter Sym Conditions Min. Typ. Max. Unit Remarks Source Analog ISHA VSHA=+5.0V 3.0 6.0 mA Note 7-8 current Digital ISHD VSHD=+3.3V 1.5 3.0 mA Note 7-8 Gate High IDD VDD=+15.0V 0.05 0.10 mA Note 7-9 current Low IEE VEE=-10.0V -0.05 -0.10 mA Note 7-9 Note 7-8Vertical stripe pattern alternating 21 gray scale (GS21) with 42 gray scale (GS42) every 1 dot. Note 7-964-Gray-bar vertical pattern (GS0 to GS63 for horizontal way) LD-21910A-11 (8)Input Signals, Basic Display Color and Gray Scale of Each Color Table 8 Colors & Data signal Gray scale Gray Scale R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 Basic color Gray Scale of red Gray Scale of green Gray Scale of bleu Black - 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue - 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green - 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan - 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red - 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta - 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow - 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Brighter GS61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GS62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Red GS63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 Brighter GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 GS62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 Green GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 Brighter GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 Bleu GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0: Low level voltage 1: High level voltage Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. LD-21910A-12 (9)Optical characteristics 9-1)Not driving the Back light condition Table 9 (VSHA=+5V, VSHD=+3.3V, VDD=+15V, VEE=-10V, Ta=25C) Parameter Symbol Condition Min. Typ. Max. Unit 35 50 - degree 35 50 - degree 35 50 - degree 2 3 - - 30 60 ms 0.273 50 0.323 100 0.373 ms y 0.303 0.353 0.403 x 0.310 0.360 0.410 y 0.267 0.317 0.367 x 0.257 0.307 0.357 y 0.322 0.372 0.422 x 0.194 0.244 0.294 y 0.222 0.272 0.322 2.5 4 - 21,22 Viewing angle range 11 CR1.5 12 Contrast ratio Response Rise r time Fall d White chromaticity Red chromaticity Green chromaticity Blue chromaticity Reflection ratio =0 CRmax =0 x =0 R Remarks [Note 9-1,2] [Note 9-2,4] [Note 9-3] [Note 9-4] % [Note 9-5] * The measuring method of the optical characteristics is shown by the following figure. * A measurement device is Otsuka luminance meter LCD5000. (With the diffusion reflection unit.) Normal line Photodetector (with luminosity correction system) Chemical coated surface (Optical diffusion treatment) A diffusion beam A diffusion beam A beam (through an optical fiber) LCD module Center of display Measuring method (a) for optical characteristics LD-21910A-13 9-2)Driving the Back light condition Table 10 (VSHA=+5V, VSHD=+3.3V, VDD=+15V, VEE=-10V, Ta=25C) Parameter Symbol Condition 21,22 Viewing angle range 11 CR2 12 Contrast ratio Crmax = 0 Min Typ Max Unit 30 40 - degree 40 50 - degree 30 40 - degree 50 80 - Rise r - 30 60 ms time Fall d 50 0.300 100 0.350 ms x 0.250 y 0.280 0.330 0.380 x 0.470 0.520 0.570 y 0.280 0.330 0.380 x 0.280 0.330 0.380 y 0.430 0.480 0.530 x 0.110 0.160 0.210 y 0.140 0.190 0.240 Red chromaticity Green chromaticity Blue chromaticity [Note 9-1,2,6] [Note 9-2] Response White chromaticity Remarks [Note 9-3] Brightness Y = 0 180 250 - cd/m IL=20mA LED life time LL IL=20mA 5,000 hour [Note 9-7] * The measuring method of the optical characteristics is shown by the following figure. * A measurement device is TOPCON luminance meter BM-5(A) (Viewing cone 1) or SR-3. Photodetector(including luminosity facter) LCD module Center Measuring method (c) for optical characteristics LD-21910A-14 [Note 9-1] Viewing angle range is defined as follows. Normal line 22 12 11 21 o'clock direction Definition for viewing angle [Note 9-2] Definition of contrast ratio: The contrast ratio is defined as follows: Photodetecter output with all pixels white(GS63) Contrast ratio (CR) Photodetecter output with all pixels black(GS0) VCOMAC=5.0VP-P [Note 9-3] Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". White Black White 100% 90% Photodetecter output (arbitrary unit) 10% 0% r d Time [Note 9-4] A measurement device is Minolta CM-2002. [Note 9-5] Definition of reflection ratio: Light detected level of the reflection by the LCD module Reflection ratio Light detected level of the reflection by the standard white board [Note 9-6] A measurement device is ELDIM EZContrast [Note 9-7] This is the reference value. The White-LED life time is defined as a time when brightness not to become under 50% of the original value. (at Ta=25C) LD-21910A-15 (10) Display quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standards for TFT-LCD. (11) Mechanical characteristics 11-1) External appearance See Fig. 1 11-2) FPC (for LCD panel) characteristics (1)Specific connector FH12A-50S-0.5SH(55) or FH12-50S-0.5SH(55) (HIROSE) (2) Bending endurance of the bending slits portion No line of the FPC is broken for the bending test (Bending radius=0.6mm and angle=90) in 30 cycles. (12) Handling Precautions 12-1) Insertion and taking out of FPCs (1) Be sure to turn off the power supply when inserting or disconnecting the FPC. (2) Please insert FPC in the connector carefully so that the tension should not hang. 12-2) Handling of FPCs The FPC for LCD panel shall be bent only slit portion. The bending slit shall be bent uniformly on the whole slit portion with bending radius larger than 0.6mm, and only inner side (back side of the module). Don't bend it outer side (display surface side). Don't give the FPCs too large force, for example, hanging the module with holding FPC. 12-3) Installation of the module On mounting the module, be sure to fix the module on the same plane. Taking care not to warp or twist the module. 12-4) Precautions when mounting (3) If water droplets and oil attaches to it for a long time, discoloration and staining occurs. Wipe them off immediately. (4) Glass is used for the TFT-LCD panel. If it is dropped or bumped against a hard object, it may be broken. Handle it with sufficient care. (5) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling. Observe all other precautionary requirements in handling components. 12-5) Others (1) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such environment. The panel characteristic might be deteriorated and the display fineness decrease when strong light is irradiated to the liquid crystal panel. (2) If it is kept at a temperature below the rated storage temperature, it becomes coagulated and the panel may be broken. Also, if it is kept at a temperature above the rated storage temperature, it becomes isotropic liquid and does not return to its original state. Therefore, it is desirable to keep it at room temperature as much as possible. (3) If the LCD breaks, don't put internal liquid crystal into the mouth. Rinse it as soon as possible if it gets inside your eye or mouth by mistake. When the liquid crystal sticks to the hands, feet and clothes, wash it out immediately. (4) Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or spots. (5) Observe general precautions for all electronic components. (6) VCOM must be adjusted on condition of your final product. No adjustment causes the deterioration for display quality. (7) Static image should not be displayed more than 5 minutes in order to prevent from occurrence of afterimage. (8) Since the front polarizer is easily damaged, pay attention not to scratch it. Blow away dust on the polarizer with antistatic 2 blow. It is undesirable to wipe off because a polarizer is sensitive. It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer. When unavoidable, wipe off carefully with a cloth for wiping lenses. (9) In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which degrades LD-21910A-16 display quality. (10) When handling LCD modules and assembling them into cabinets, that long-terms storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, causes corrosion and discoloration of the modules. Therefore, please avoid these uses. Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and oxime series), tray forming agent (azo compound) etc, in the cabinet or the packing materials may induce abnormal display with polarizer film deterioration regardless of contact or no contact to polarizer film. Be sure to confirm the component of them. (11) The LED used for this product is very sensitive to the temperature. Luminance decreases rapidly when it issued for a long time under the environment of the high temperature. Please consult our company when it is used under the environment like the above mentioned. (12) Notice: Never dismantle the module, because it will cause failure. Moreover, please do not peel off the tapes other than the creped paper tape (yellow tape) of a protection film pasted to the product. (13) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan. LD-21910A-17 (13) Reliability Test Conditions for TFT-LCD Module Table 11 No. Test items Test conditions 1 High temperature storage test Ta=+70C 240h 2 Low temperature storage test Ta=-25C 240h 3 High temperature and high humidity Tp=+40C , 95%RH 240h operating test (But no condensation of dew) 4 High temperature operating test Tp=+70C 240h 5 Low temperature operating test Tp=-10C 240h 6 Electro static discharge test 200V/200pF(0) to Terminals(Contact) (1 time for each terminals) 8kV/150pF(330) to Housing bezel (Contact) 15kV/150pF(330) to Housing bezel(in Air) 7 Shock tset 980 m/s, 6 ms X, Y, Z 3 times for each direction (JIS C0041, A-7 Condition C) 8 Vibration test Frequency range: 10Hz to 55Hz Stroke: 1.5 mm Sweep: 10Hz to 55Hz X,Y,Z 2 hours for each direction (total 6 hours) (JIS C0040,A-10 Condition A) 9 Heat shock test Ta=-25 to +70C / 5 cycles (1h) 10 FPC Bending Test (1h) Bending 30 times by bending radius R0.6mm and angle=90 (LCD FPC) NoteTa = Ambient temperature, Tp = Panel temperature Check items Test No.1 to 9: In the standard condition, there shall be no practical problems that may affect the display function. (14) Others 14-1) Indication of lot number The lot number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions). LQ035Q7DH07 N model No. lot No. 14-2) Used Regulation of Chemical Substances Breaking Ozone Stratum Substances with the object of regulating: CFCS, Carbon tetrachloride, Halon 1,1,1-Trichloro ethane (Methyl chloroform) (a) This LCD module, Constructed part and Parts don't contain the above substances. (b) This LCD module, Constructed part and Parts don't contain the above substances in processes of manufacture. 14-3) If some problems arise about mentioned items in this document and other items, the user of the TFT-LCD module and SHARP will cooperate and make efforts to solve the problems with mutual respect and good will. LD-21910A-18 (15) Forwarding form (See Fig.2 Package Form) a) Piling number of cartons : Max 8 b) Package quality in one cartons : 100pcs c) Carton size : 575mm x 332mm x 209mm d) Total mass of 1 carton filled with full modules: 7450g Conditions for storage Environment (1)Temperature: 0 to 40C (2)Humidity: 60%RH or less (at 40C) No dew condensation at low temperature and high humidity. (3)Atmosphere: Harmful gas, such as acid or alkali which bites electronic components and/or wires, must not be detected. (4)Period: about 3 months (5)Opening of the package: In order to prevent the LCD module from breakdown by electrostatic charges, please control the room humidity over 50%RH and open the package taking sufficient countermeasures against electrostatic charges, such as earth, etc Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328 CHINA Sharp Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com JAPAN Sharp Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com SINGAPORE Sharp Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855 HONG KONG Sharp-Roxy (Hong Kong) Ltd. Level 26, Tower 1, Kowloon Commerce Centre, No. 51, Kwai Cheong Road, Kwai Chung, New Territories, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 602-603, 6/F., International Chamber of Commerce Tower, 168 Fuhua Rd. 3, CBD, Futian District, Shenzhen 518048, Guangdong, P.R. China Phone: (86) 755-88313505 Fax: (86) 755-88313515 KOREA Sharp Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage. LD-21910A