REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add CAGE number 50364 as a supplier for 02 and 03 device types. Add 04 device type. Add CAGE number 1FN41 as a supplier of the K package. Editorial changes throughout entire document. Remove C as a test condition option. 89-08-23 M. A. Frye B Change CI and CO values in Table I. Incorporate power reset feature. Add 05 device. Add CAGE number 65786 for 04K, 04L and 043 devices. Add footnote 7/ to Table I. Editorial changes throughout entire document. 91-11-06 M. A. Frye C Update drawing to current requirements. Editorial changes throughout. - gap 01-11-02 Raymond Monnin D Boilerplate update part of 5 year review. ksr 06-08-18 Raymond Monnin E Corrected IIL and IIH parameters in Table I. ksr 10-03-29 Charles F. Saffle THE ORIGINAL FRONT PAGE HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Jeffery D. Bowling STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY http://www.dscc.dla.mil Charles Reusing APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE Michael A. Frye DRAWING APPROVAL DATE 88-07-27 AMSC N/A REVISION LEVEL E MICROCIRCUIT, MEMORY, DIGITAL, CMOS, ONE-TIME PROGRAMMABLE, PROGRAMMABLE ARRAY LOGIC, MONOLITHIC SILICON SIZE A SHEET DSCC FORM 2233 APR 97 CAGE CODE 67268 1 OF 5962-88670 11 5962-E255-10 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-88670 01 L X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number 01 C22V10 02 C22V10 03 C22V10 04 C22V10 05 C22V10 Circuit function Access time 22-input 10-output and-or-logic array 22-input 10-output and-or-logic array 22-input 10-output and-or-logic array 22-input 10-output and-or-logic array 22-input 10-output and-or-logic array 25 ns 30 ns 40 ns 20 ns 15 ns 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter K L 3 Descriptive designator GDFP2-F24 or CDFP3-F24 GDIP3-T24 or CDIP4-T24 CQCC1-N28 Terminals Package style 24 24 28 Flat package Dual-in-line Leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. 1/ Supply voltage range ........................................................................ Input voltage range .......................................................................... Output voltage applied range ........................................................... Output sink current ........................................................................... Thermal resistance, junction-to-case (JC): ...................................... Maximum power dissipation (PD) 3/ ................................................. Maximum junction temperature (TJ) ................................................. Lead temperature (soldering, 10 seconds maximum) ...................... Storage temperature range .............................................................. Temperature under bias ................................................................... -0.5 V dc to +7.0 V dc -2.0 V dc to +7.0 V dc 2/ -0.5 V dc to +7.0 V dc 2/ 16 mA See MIL-STD-1835 1.2 W +175C +260C -65C to +150C -55C to +125C __________ 1/ All voltages referenced to VSS. 2/ Minimum voltage is -0.6 V dc which may undershoot to -2.0 V dc for pulses of less than 20 ns. Maximum output pin voltage is VCC +0.75 V dc which may overshoot to +7.0 V dc for pulses of less than 20 ns. 3/ Must withstand the added PD due to short circuit test; e.g., IOS. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 2 1.4 Recommended operating conditions. Supply voltage (VCC) ........................................................................ High level input voltage (VIH) ............................................................ Low level input voltage (VIL) ............................................................. Case operating temperature range (TC) ........................................... 4.5 V dc to 5.5 V dc 2.0 V dc minimum 0.8 V dc maximum -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.3.1 Unprogrammed devices. The truth table for unprogrammed devices for contracts involving no altered item drawing shall be as specified on figure 2. When required in groups A, C, or D (see 4.3), the devices shall be programmed by the manufacturer prior to test with a minimum of 50 percent of the total number of gates programmed or to any altered item drawing pattern which includes at least 25 percent of the total number of gates programmed. 3.2.3.2 Programmed devices. The truth tables for programmed devices shall be as specified by an attached altered item drawing. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 3 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator "C" shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator "C" shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result in a wide variety of configurations; two processing options are provided for selection in the contract, using an altered item drawing. 3.10.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.3.1 and table II. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program configuration. 3.10.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 4 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 7/ VSS = 0 V, -55C TC +125C 4.5 V VCC 5.5 V Group A subgroups Device type 1, 2, 3 All 1, 2, 3 All IOZ unless otherwise specified IO = -2.0 mA VIH = 2.0 V VIL = 0.8 V IO = 12.0 mA VIH = 2.0 V VIL = 0.8 V VCC = 5.5 V 1, 2, 3 All IIH VIH = 5.5 V (excludes I/O pins) 1, 2, 3 All IIL VIL = GND (excludes I/O pins) 1, 2, 3 All ICC VCC = 5.5 V, VIN = GND 1, 2, 3 IOS VCC = 5.5 V, VO = 0.5 V Outputs open for unprogrammed device VI = 0 V, VCC = 5.0 V, TA = +25C, f = 1 MHz, (see 4.3.1c) VO = 0 V, VCC = 5.0 V, TA = +25C, f = 1 MHz, (see 4.3.1c) 1, 2, 3 01-03 04, 05 All 4 All High level output voltage Low level output voltage High impedance output leakage current 2/ High level input current Low level input current Standby power supply current Output short circuit current 3/ 4/ VOH Input capacitance 4/ 5/ CI Output capacitance 4/ 5/ CO VOL Functional test Input to output enable tEA Input to output disable tER Input or feedback to nonregistered output tPD Clock to output tCO Min 2.4 Unit Max V 0.5 V 40 A -10 +10 A -10 +10 A -40 -30 100 120 -90 mA mA mA pF 10 4 All pF 10 See footnote 4/ of Table IIA 7,8A,8B All VCC = 4.5 V, CL = 5 pF, See figure 3 (circuit A) and figure 4 9, 10, 11 01 02 03 04 05 01 02 03 04 05 01 02 03 04 05 01, 04 02 03 05 9, 10, 11 VCC = 4.5 V, CL = 50 pF, See figure 3 (circuit B) and figure 4 Limits 9, 10, 11 9, 10, 11 25 30 40 20 15 25 30 40 20 15 25 30 40 20 15 15 20 25 10 ns ns ns ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 5 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 7/ VSS = 0 V, -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified VCC = 4.5 V, CL = 50 pF, See figure 3 (circuit B) and figure 4 Group A subgroups Clock period (tco + ts) tP Clock pulse width 4/ 6/ tW 9, 10, 11 Setup time 4/ 6/ tS 9, 10, 11 Hold time 4/ 6/ tH 9, 10, 11 Maximum clock frequency 4/ 6/ fMAX 9, 10, 11 Asynchronous reset pulse width tAW 9, 10, 11 Asynchronous reset recovery time tAR 9, 10, 11 Asynchronous reset to registered output reset tAP 9, 10, 11 Power-up reset time 1/ 2/ 3/ 4/ 5/ 6/ 7/ 4/ tPR See figure 5 9, 10, 11 9, 10, 11 Device type 01 02 03 04 05 01, 04 02 03 05 01 02 03 04 05 All 01 02 03 04 05 01 02 03 04 05 01 02 03 04 05 01, 04 02 03 05 All Limits Min 33 40 55 32 22 15 20 27 6 18 20 30 17 12 0 Unit Max ns ns ns ns 30 25 18 31 45 25 30 40 20 15 25 30 40 20 15 MHz ns ns 25 30 40 20 1 ns s All voltages are referenced to ground. I/O terminal leakage is the worst case of IIX or IOZ. Only one output shorted at a time. Tested initially and after any design or process changes that affect that parameter, and therefore shall be guaranteed to the limits specified in table I. All pins not being tested are to be open. Test applies only to register outputs. AC testing. Input pulse levels are 0 to 3.0 V with transition times of 5ns or less. Timing reference levels are 1.5 V unless otherwise specified. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 6 Device types Case outlines Terminal number 01, 02, 03, 04, 05 K, L 3 Terminal symbol 1 CP/I NC 2 I CP/I 3 I I 4 I I 5 I I 6 I I 7 I I 8 I NC 9 I I 10 I I 11 I I 12 GND I 13 I I 14 I/O GND 15 I/O NC 16 I/O I 17 I/O I/O 18 I/O I/O 19 I/O I/O 20 I/O I/O 21 I/O I/O 22 I/O NC 23 I/O I/O 24 VCC I/O 25 --- I/O 26 --- I/O 27 --- I/O 28 --- VCC FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 7 Truth table Input pins Output pins CP/I I I I I I I I I I I I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O X X X X X X X X X X X X Z Z Z Z Z Z Z Z Z Z NOTES: 1. Z = 3-state 2. X = don't care FIGURE 2. Truth table (unprogrammed). NOTES: 1. AC testing. Inputs pulse levels are 0 to 3.0 V with transition times of 5 ns or less. Time reference levels are 1.5 V unless otherwise specified. 2. tEA and tER transition are measured 500 mV from steady state voltage. FIGURE 3. Output test circuits. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 8 FIGURE 4. Switching waveforms. NOTE: The power-up reset feature ensures that all flip-flops will be reset to low after the device has been powered up. The following conditions are required: a) The VCC rise must be monotonic. b) After reset occurs, all applicable input and feedback setup times must be met before driving the clock pin high c) The clock signal must remain stable beginning prior to the occurrence of the 10% level and continuing until the end of tPR. FIGURE 5. Power-up reset waveform. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 9 TABLE II. Electrical test requirements. 1/, 2/, 3/, 4/ MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) 1 Final electrical test parameters (method 5004) for unprogrammed devices 1*, 2, 3, 7*, 8A, 8B Final electrical test parameters (method 5004) for programmed devices 1*, 2, 3, 7*, 8A, 8B, 9 Group A test requirements (method 5005) 1, 2, 3, 4**, 7, 8A, 8B, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 2, 3, 7, 8A, 8B 1/ * indicates PDA applies to subgroups 1 and 7. 2/ Any or all subgroups may be combined when using high-speed testers. 3/ ** see 4.3.1c. 4/ Subgroups 7 and 8 functional tests shall also verify that no cells are programmed for unprogrammed devices or that the altered item drawing pattern exists for programmed devices. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroup 4 (CIN and COUT measurement) shall be measured only for the initial test and after process or design changes which may affect input capacitance. Sample size is 15 devices with no failures, and all input and output terminals tested. d. Unprogrammed devices shall be tested for programmability and ac performance compliance to the requirements of group A, subgroups 9, 10, and 11. (1) A sample shall be selected to satisfy programmability requirements prior to performing subgroups 9, 10, and 11. Twelve devices shall be submitted to programming (see 3.2.3.1). If more than two devices fail to program, the lot shall be rejected. At the manufacturer's option, the sample may be increased to 24 total devices with no more than 4 total device failures allowable. (2) Ten devices from the programmability sample shall be submitted to the requirements of group A, subgroups 9, 10, and 11. If more than two devices fail, the lot shall be rejected. At the manufacturer's option, the sample may be increased to 20 total devices with no more than 4 total device failures allowable. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 10 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. c. (1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. For quality conformance inspection, the programmability sample (see 4.3.1d) shall be included in subgroup 1 test. 4.4 Programming procedures. The programming procedures shall be as specified by the device manufacturer. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DSCC-VA. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-88670 A REVISION LEVEL E SHEET 11 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 10-03-29 Approved sources of supply for SMD 5962-88670 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ 5962-8867001KA 5962-8867001LA 5962-88670013A 5962-8867002KA 5962-8867002LA 5962-88670023A 5962-8867003KA 5962-8867003LA 5962-88670033A 5962-8867004KA 5962-8867004LA 5962-88670043A 5962-8867005KA 5962-8867005LA 5962-88670053A Vendor CAGE number 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 3/ 0C7V7 3/ 0C7V7 3/ 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ 0C7V7 3/ Vendor similar PIN 2/ PALC22V10-25KMB AT22V10-25FM/883 PALC22V10-25DMB AT22V10-25GM/883 PALC22V10-25LMB AT22V10-25NM/883 PALC22V10-30KMB AT22V10-30FM/883 PALC22V10-30DMB AT22V10-30GM/883 PALC22V10-30LMB AT22V10-30NM/883 PALC22V10H-30ML883B PALC22V10-40KMB AT22V10-40FM/883 PALC22V10-40DMB AT22V10-40GM/883 PALC22V10H-40MJS883B PALC22V10-40LMB AT22V10-40NM/883 PALC22V10B-20KMB AT22V10-20FM/883 PALC22V10B-20DMB AT22V10-20GM/883 PALC22V10B-20LMB AT22V10-20NM/883 PALC22V10B-15KMB AT22V10-15FM/883 PALC22V10B-15DMB AT22V10-15GM/883 PALC22V10B-15LMB AT22V10-15NM/883 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. 1 of 2 STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued. Vendor CAGE number Vendor name and address 0C7V7 QP Semiconductor 2945 Oakmead Village Court Santa Clara, CA 95051 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. 2 of 2