Features * * * * * * * * * * * * Supply Voltage: 8.5V RF Frequency Range: 1400 MHz to 1550 MHz IF Frequency Range: 150 MHz to 250 MHz Enhanced IM3 Rejection Overall Gain Control Range: 30 dB Typically DSB Noise Figure: 10 dB Gain-controlled Amplifier and L-band Mixer Power-down Function for the Analog Part On-chip Gain-control Circuitry On-chip VCO, Typical Frequency 1261.568 MHz Internal VCO Can Be Overdriven by an External LO On-chip Frequency Synthesizer - Fixed LO Divider Factor: 2464 - Nine Selectable Reference Divider Factors: 32, 33, 35, 36, 48, 49, 63, 64, 65 - A Reference Oscillator (Can Be Overdriven by an External Reference Signal) - Tri-state Phase Detector with Programmable Charge Pump - Programmable Deactivation of Tuning Output - Lock-status Indication - Test Interface 1. Description L-band Down-converter for DAB Receivers ATR2730 Preliminary The ATR2730 is a monolithically integrated L-band down-converter circuit fabricated with Atmel(R)'s advanced UHF5S technology. This IC covers all functions of an L-band down-converter in a DAB receiver. The device includes a gain-controlled amplifier, a gain-controlled mixer, an output buffer, a gain control block, a power-save function for the analog part, an L-band oscillator, and a complete frequency synthesizer unit. The frequency synthesizer block consists of a reference oscillator/buffer, a reference divider, an RF divider, a tri-state phase detector, a loop filter amplifier, a lock detector, a programmable charge pump, a test interface, and a control interface. 4903C-DAB-03/07 Figure 1-1. Block Diagram IF TH 17 AGC VCC1 VCC3 VCC4 VCC2 19 3 20 28 6, 7, 8, 21, 22, 23, 24 18 Internal 5V supply voltage for frequency synthesizer U Analog part RF NRF TANK VREF GND 9 26 Voltage stabilizer 14 Bandgap PLCK Lock detector 25 20 k 5 12 RF counter : 2464 VCO CD Tristate phase detector 4 Reference counter : Nref Power save (analog part) Charge pump 200/300 13 PD Lock detector Test interface 2 1 15 16 PSM OSCB OSCE 11 TI Control interface 10 CI 27 SI1 2 SI2 ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] 2. Pin Configuration Figure 2-1. Pinning SSO28 PSM 1 28 VCC4 SI2 2 27 SI1 VCC1 3 26 RF VREF 4 25 NRF TANK 5 24 GND GND 6 23 GND GND 7 22 GND GND 8 21 GND VCC2 9 20 VCC3 CI 10 19 IF TI 11 18 AGC CD 12 17 TH PD 13 16 OSCE PLCK 14 15 OSCB 3 4903C-DAB-03/07 Table 2-1. 4 Pin Description Pin Symbol Function 1 PSM 2 SI2 3 VCC1 Supply voltage VCO 4 VREF Reference pin of VCO 5 TANK Tank pin of VCO 6, 7, 8, 21, 22, 23, 24 GND Ground 9 VCC2 Supply voltage PLL 10 CI Power save mode Control input Control input 11 TI Test interface 12 CD Active filter output 13 PD Tri-state charge pump output 14 PLCK Lock-indication output (open collector) 15 OSCB Input of internal oscillator/buffer 16 OSCE Output of internal oscillator/buffer 17 TH Threshold voltage of comparator 18 AGC Charge-pump output of comparator, AGC input for amplifier and mixer 19 IF 20 VCC3 Intermediate frequency output 25 NRF 26 RF RF input 27 SI1 Control input 28 VCC4 Supply voltage RF input (inverted) Supply voltage ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] 3. Functional Description The ATR2730 is an L-band down-converter circuit covering a gain-controlled amplifier, a gain-controlled mixer, an output buffer, a gain control circuitry, an L-band oscillator, and a frequency synthesizer block. Designed for applications in a DAB receiver, the circuit down-converts incoming L-band signals in the frequency range of 1452 MHz to 1492 MHz to an IF frequency in the range of 190 MHz to 230 MHz, which can be handled by a subsequent DAB tuner. A block diagram of this circuit is shown in Figure 1-1 on page 2. 3.1 Gain-controlled Amplifier RF signals applied to the RF input pin are amplified by a gain-controlled amplifier. The complementary pin NRF is not internally blocked; it is recommended to block this pin carefully by an external capacitor. The gain-control voltage is generated by internal gain-control circuitry. The output signal of this amplifier is fed to a gain-controlled mixer. 3.2 Gain-controlled Mixer and Output Buffer The purpose of this mixer is to down-convert the L-band signal in the frequency range of 1452 MHz to 1492 MHz to an IF frequency in the range of about 190 MHz to 230 MHz. Like the amplifier, the gain of the mixer is controlled by the gain-control circuitry. The IF signal is buffered and filtered by a one-pole low-pass filter at a 3 dB frequency of about 500 MHz, and then it is fed to the single-ended output pin IF. 3.3 Gain-control Circuitry The gain-control circuitry measures the signal power, compares it with a certain power level and generates control voltages for the gain-controlled amplifier and mixer. An equivalent circuit of this functional block is shown in Figure 10-1 on page 14. In order to meet this functionality, the output signal of the buffer amplifier is weakly band-pass filtered (transition range of about 60 MHz to 550 MHz), rectified, low-pass filtered, and fed to a comparator whose threshold can be defined by an external resistor, RTH, at pin TH. By varying the value of this resistor, a power threshold of about -33 dBm to -20 dBm can be selected. In order to achieve a good intermodulation ratio, it is recommended to keep the power threshold below -25 dBm. An appropriate application is shown in Figure 8-1 on page 12. Depending on the selection made by the comparator, a charge pump charges or discharges a capacitor which is applied to the AGC pin. By varying this capacitor, different time constants of the AGC loop can be realized. The voltage arising at the AGC pin is used to control the gain setting of the gain-controlled amplifier and mixer. The voltage at pin AGC is in the range of 5.75V for maximum gain and 0.3V for minimum gain. This voltage can be use to control a dual-gate GaAs-FET in front of the ATR2730 to achieve an extended AGC range. By applying an external voltage to the AGC pin, the internal AGC loop can be overdriven. 5 4903C-DAB-03/07 3.4 Voltage-controlled Oscillator A voltage-controlled oscillator supplies an LO signal to the mixer. An equivalent circuit of this oscillator is shown in Figure 10-2 on page 14. In the application circuits (Figure 10-3 on page 15 and Figure 11-1 on page 16), a ceramic coaxial resonator is applied to the oscillator's TANK and VREF pins. It should be noted that Vref has to be blocked carefully. Figure 11-1 shows a different application where the oscillator is overdriven by an external oscillator. In either case, a DC path at a low impedance must be established between the TANK and VREF pins. The output signal of the oscillator is fed to the LO divider block of the frequency synthesizer unit which locks the VCO's frequency on the frequency of a reference oscillator. Figure 9-1 on page 13 shows the typical phase-noise performance of the oscillator in locked state. 3.5 Overall Properties of the Signal Path The overall gain of this circuit amounts to 24 dB, the gain-control range is about 30 dB. With a new AGC concept in the amplifier and mixer, the ATR2730 reaches better intermodulation distances (DIM3) at higher IF-output power levels. 3.6 Power Save Mode For VPSM > 2V (pin 1) the power consumption in the analog part (gain-controlled amplifier and mixer and gain-controlled circuitry) is reduced by 80%. The VCO and the PLL is not influenced by the power-down mode. 3.7 Frequency Synthesizer The frequency synthesizer block consists of a reference oscillator, a reference divider, an LO divider in order to divide the frequency of the internal oscillator, a tri-state phase detector, a lock detector, a programmable charge pump, a loop filter amplifier, a control interface, and a test interface. The control interface is accessed by three control pins, CI, SI1 and SI2. The test interface provides test signals which represent output signals of the reference and the LO divider. The purpose of this unit is to lock the frequency fVCO of the internal VCO on the frequency fref of the reference signal applied to the input pin OSCB phase-locked loop according to the following equation: fVCO = SF x fref / SFref where: SF = 2464, SFref is the scaling factor of the reference divider according to Table 3-1 6 ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] Table 3-1. 3.8 Scaling Factors of the Reference Frequency Voltage at Pin SI1 Voltage at Pin SI2 SFref Reference Oscillator Frequency GND OPEN 36 18.432 MHz GND VCC 33 - GND GND 48 24.576 MHz OPEN OPEN 65 - OPEN VCC 63 - OPEN GND 64 32.768 MHz VCC OPEN 35 17.920 MHZ VCC VCC 32 16.384 MHz VCC GND 49 - Reference Oscillator An on-chip crystal oscillator generates the reference signal which is fed to the reference divider. By connecting a quartz crystal to pins OSCE and OSCB according to Figure 11-2 on page 16, this oscillator generates a highly stable reference signal. The ATR2731 (Atmel's one-chip front-end IC) offers the reference signal at pin FREF. This reference signal (LC filtered to suppress harmonics) can be used to overdrive the oscillator. In this application (see Figure 11-3 on page 16) the reference signal has to be applied to the pin OSCB and the pin OSCE must be left open. 3.9 Reference Divider Nine different scaling factors of the reference divider can be selected by different voltage settings at the input pins SI1 and SI2: 32, 33(1), 35, 36, 48, 49(1), 63(1), 64, 65(1). The reference divider factors result in reference oscillator frequencies shown in Table 3-1. Note: 3.10 1. These scaling factors result in an output frequency of the reference divider of 512 kHz. If harmonics of the Bd. 3 VCO fall in the L-band reception band, these spurious signals can influence the AGC of ATR2730, which could be a problem for small incoming signals. In this case it is possible to switch the reference divider from nref to nref + 1. LO Divider The LO divider is operated at the fixed division ratio 2464. Assuming the settings described in the section "Reference Divider" , the oscillator's frequency is controlled to be 1261.568 MHz in the locked state, and the output frequency of the RF divider is 512 kHz. 3.11 Phase Comparator, Charge Pump and Loop Filter The tri-state phase detector causes the charge pump to source or sink current at the output pin PD depending on the phase relation of its input signals, which are provided by the reference and the RF divider respectively. Using the control pin CI, two different values of this current can be selected, and the charge-pump current can be switched off. The input of the high-gain amplifier (output pin CD), which is implemented in order to construct a loop filter as shown in the application circuit, can be switched to GND by means of the control pin CI (see Table 3-2 on page 8). In the application circuit, the loop filter is completed by connecting the pins PD and CD by an appropriate RC network. 7 4903C-DAB-03/07 3.12 Lock Detector An internal lock detector checks if the phase difference of the input signals of the phase detector is smaller than approximately 250 ns in seven subsequent comparisons. If a phase lock is detected, the open collector output pin PLCK is set to HIGH. It should be noted that the output current of this pin must be limited by external circuitry as it is not limited internally. If the voltage at the control pin CI is chosen to be half the supply voltage, or if this control pin is left open, the lock-detector function is deactivated and the logical value of the PLCK output is undefined. 3.13 Test Interface If the input control pin CI is left open (high impedance state), a test signal, which monitors the output frequency of the reference divider, appears at the output pin TI. Analogous to the reference divider, a test signal monitoring the output frequency of the RF divider appears at the test interface output pin TI, if the input control pin CI is connected to VCC/2. Table 3-2. 8 Control Interface (CI) Settings CI PD PLCK TI GND 200 A Ok - Vs 300 A Ok - VCC/2 0 A Undefined RF divider Open Connected to GND Undefined Reference divider ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] 4. Absolute Maximum Ratings Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameters Pins Symbol Value Unit Supply voltage 3, 9, 20 and 28 VCC -0.3 to +9.5 V RF input voltage 25 and 26 VRF 750 mVpp Voltage at pin AGC 18 VAGC 0.5 to 6 V Voltage at pin TH 17 VTH -0.3 to +4.0 V Input voltage at pin TANK (internal oscillator overdriven) 5 VTANK 1 Vpp Current at IF output 19 IIF 4.0 mA Reference input voltage (diff.) 15 Control input voltage 1, 2, 10 and 27 OSCB 1 Vpp CI, SI1, SI2, PD -0.3 to +9.5 V PLCK output current 14 IPLCK 0.5 mA PLCK output voltage 14 VPLCK -0.3 to +5.5 V Junction temperature Tj 125 C Storage temperature Tstg -40 to +125 C Symbol Value Unit VCC 8 to 9.35 V Tamb -40 to +85 C Symbol Value Unit RthJA 50 K/W 5. Operating Range Parameters Pins Supply voltage 3, 9, 20 and 28 Ambient Temperature 6. Thermal Resistance Parameters Junction ambient SSO28 (mod.) 9 4903C-DAB-03/07 7. Electrical Characteristics Operating conditions: VCC = 8.5V, Tamb = 25 C unless otherwise specified. (See application circuit Figure 10-3 on page 15.) No. Parameters Test Conditions 1.1 Supply current (max. gain) pRF = -60 dBm VPSM < 0.5V 1.2 Supply current (min. gain) 1.3 Supply current (power-save mode) 2 Pin Symbol Typ. Max. Unit Type* IS,MAX 40 48 mA A pRF = -10 dBm VPSM < 0.5V IS,MIN 41 50 mA B pRF = -10 dBm VPSM > 2V IS,PD 20 24 mA A 24 dB A -8 dB B 26 19 Amplifier Mixer Pin 26 2.1 Maximum conversion gain pRF = -60 dBm gc,max 2.2 Minimum conversion gain pRF = -15 dBm gc,min 2.3 AGC range 2.4 Third-order 2-tone intermodulation ratio pRF1 + pRF2 = -10 dBm pRF1 + pRF2 = -15 dBm 2.5 DSB noise figure (50 system) Maximum gain Minimum gain 3 RF Input 3.1 Frequency range 3.2 Maximum input power 3.3 Input impedance 4 Min. 20 gc 28 32 dB A dim3 30 35 35 40 dB dB B A 10 30 dB dB D MHz C NF 26 fin,RF dim3 20 dB IF Output 1400 1550 pin,max,RF -6 dBm C Zin,RF 200 || 1 || pF D MHz C D 19 150 250 4.1 Frequency range fout,IF 4.2 Output impedance Zout,IF 50 4.3 Voltage standing wave ratio VSWRIF 2.0 100 5 5.1 5.2 Gain Control Threshold adjustment Charge pump current k D 125 A A -100 -75 A A 0.1 0.6 V A V A External resistor 17 RTH pRF = -10 dBm VAGC = 3.5V 18 ICP,P 75 100 ICP,N -125 pRF = -60 dBm VAGC = 3.5V 5.3 Minimum gain control voltage pRF = -10 dBm 18 VAGCmin 5.4 Maximum gain control voltage pRF = -60 dBm 18 VAGCmax 5.5 5.75 fLO 1000 1261.568 6 VCO 5 6.1 Frequency 6.2 Phase noise 1 kHz distance 6.3 Minimum input power 6.4 Maximum input power VCO overdriven, see "Application Circuit" (Figure 10-3 on page 15) 7 7.1 D 1500 MHz L1kHz -75 dBc/Hz C pLO,MIN -11 dBm C pLO,MAX -5 dBm C SF 2464 Frequency Synthesizer RF divide factor A *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter 10 ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] 7. Electrical Characteristics (Continued) Operating conditions: VCC = 8.5V, Tamb = 25 C unless otherwise specified. (See application circuit Figure 10-3 on page 15.) No. Parameters Test Conditions 7.2 Reference divide factor SI1 = GND, SI2 = GND SI1 = GND, SI2 = VCC SI1 = GND, SI2 = open SI1 = VCC, SI2 = GND SI1 = VCC, SI2 = VCC SI1 = VCC, SI2 = open SI1 = open, SI2 = GND SI1 = open, SI2 = VCC SI1 = open, SI2 = open Pin Symbol 7.3 Input frequency range Input sensitivity 15 Vrefs fref 7.5 Maximum input signal 15 Vrefmax 7.6 Input impedance Zref 8 Phase Detector Single-ended 8.1 Charge-pump current 13 Pin CI connected to VCC Pin CI connected to VCC/2 Output voltage PD 8.3 Internal reference frequency 8.4 Typical tuning voltage range 12 Lock Indication PLCK 14 13 Leakage current VPLCK = 5.5V 9.2 Saturation voltage IPLCK = 0.25 mA 10 Control Inputs SI C mVrms C 300 mVrms C 2.7k || 2.5 k || pF D IPD1 240 300 360 A A 100 nA A 0.3 V A kHz B 5 V C IPLCK 10 A A VPLCK,sat 0.5 V A 0.1 VCC A VPD Vtune 512 0.3 2 and 27 VM 10.3 Pin connected to VCC 12 MHz 30 A Pin open 0 Open A VH 0.9 1 VCC A Pin connected to GND VL 0 0.1 VCC A Pin connected to VCC/2 VM VCC A Control Input CI 11.4 50 A 10.2 Input voltage 11.3 A 240 VL Input voltage Type* 200 Pin connected to GND 11.2 Unit 160 10.1 11.1 Max. IPD2 fPD 9.1 11 5 IPD1,tri 8.2 9 Pin CI open Typ. 48 33 36 49 32 35 64 63 65 SFref 7.4 Pin CI connected to GND Min. 10 Pin open Open Vopen VH Pin connected to VCC Test Interface TI 0.5 0.9 A 1 VCC A 11 Pin CI open ftest,ref 512 kHz B 12.2 LO test frequency Pin CI = VCC/2 ftest,LO 512 kHz B 12.3 Voltage swing Rload 1 M, Cload 15 pF, Pin CI open or VCC/2 Vsw 400 mVpp C V A V A 12.1 Reference test frequency 13 Power-save Mode PSM 1 13.1 PSM not active VPSM 13.2 PSM active VPSM 0.6 2.0 *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter 11 4903C-DAB-03/07 8. Gain Control Characteristics Operating conditions: VCC = 8.5V, Tamb = 27 C, fRF = 1490 MHz, FLO = 1261.568 MHz Figure 8-1. IF Output Power (Pin 19) -10 -15 pIF (dBm) -20 -25 Rth = 100 k -30 -35 -40 -60 -50 -40 -30 -20 -10 0 -10 0 pRF (dBm) Figure 8-2. Gain Control Voltage (Pin 11) 6 5 Rth = 100 k VAGC (V) 4 3 2 1 0 -60 -50 -40 -30 -20 pRF (dBm) 12 ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] 9. Phase-noise Performance Measurement conditions: Values acquired at pin 19 with HP 70000 spectrum analyzer. RF input (pin 26) is blocked with 100 pF to GND. A low phase-noise signal generator (Marconi(R) 2042) was taken as PLL reference. Figure 9-1. Phase-noise Performance Operating Conditions: fREF = 17.92 MHz, -10 dB, IPD = 200 A RL -29.29 dBm ATTEN 10 dB 10.00 dB/DIV < -75 dBc/Hz Center 1.261 568 GHz RB 100 Hz VB 100 Hz Span 50.00 kHz ST 15.00 sec 13 4903C-DAB-03/07 10. Equivalent Circuits Figure 10-1. AGC Control Circuit Gain controlled mixer Gain controlled amplifier VRef1 550 MHz IF output 60 MHz VRef2 AGC TH Rth Figure 10-2. VCO Circuit VCC VTune 47 k BBY51 1.8 pF 15 pF TANK Resonator 1 pF VREF 100 pF Resonator: Ceramic coaxial resonator Murata(R) 3 x 3 mm, 1.6 GHz DRR030 KE1R600TC 14 ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] Figure 10-3. Application Circuit VAGC 3.3 F + 8.5V RF 8.5V IF 1 nF 100 pF 100 k Quartz crystal 100 pF 100 pF 1 nF 100 pF RF NRF GND GND 21 20 19 18 17 16 15 68 pF OSCB SI1 22 OSCE 23 33 pF TH 24 IF 25 VCC3 26 GND 27 GND 28 VCC4 10 nF AGC 100 pF 10 nF 18 pF SI2 VCC1 VREF TANK GND GND GND VCC2 CI TI CD PD PLCK Power save PSM ATR2730 1 2 3 4 5 6 7 8 9 10 11 12 13 14 5V 100 pF 1 pF 10 nF Lock indication 10 nF 56 k 100 pF 1) 100 pF 100 pF 8.5V 47 k 1 nF 15 pF 1 nF 8.5V 1.8 pF D1 1 k 1 k 3.3 nF 1) 3.3 nF 1) 1) optional Example: reference divider factor = 35, fREF = 17.92 MHz, charge-pump current = 200 A 15 4903C-DAB-03/07 11. Application Circuit for External LO Signal With an external LO signal it is possible to overdrive the VCO. In this case, the internal VCO acts as an LO buffer. Figure 11-1. Application Circuit for External LO Signal External LO signal (50 signal gen.) PLO = -10 dBM TANK 100 pF 470 nH 50 VREF 1 nF Figure 11-2. Reference Oscillator Operation 68 pF OSCB Reference divider 33 pF OSCE Quartz crystal 18 pF Figure 11-3. Reference Oscillator Overdriven OSCB Reference signal L1 Reference divider C1 OSCE 16 ATR2730 [Preliminary] 4903C-DAB-03/07 ATR2730 [Preliminary] 12. Ordering Information Extended Type Number Package Remarks ATR2730-TLSY SSO28 Tube, Pb-free ATR2730-TLPY SSO28 Taped and reeled according to IEC 286-3, 180 m size, Pb-free ATR2730-TLQY SSO28 Taped and reeled according to IEC 286-3, 330 m size, Pb-free 13. Package Information 5.40.2 0.650.05 1.30.05 0.05+0.1 0.250.05 6.450.15 0.150.05 4.40.1 9.35-0.25 8.450.05 28 15 Package: SSO28 Dimensions in mm technical drawings according to DIN specifications 1 14 Drawing-No.: 6.543-5056.03-4 Issue: 1; 10.03.04 14. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. History 4903C-DAB-03/07 * Put datasheet in a new template * Section 12 "Ordering Information" on page 17 changed 17 4903C-DAB-03/07 Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-47-50 Fax: (33) 4-76-58-47-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743 Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2007 Atmel Corporation. All rights reserved. Atmel (R), logo and combinations thereof, Everywhere You Are(R) and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 4903C-DAB-03/07