FUJITSU MICROELECTRONICS DATA SHEET DS04-27205-7Ea ASSP Power Supplies BIPOLAR Switching Regulator Controller MB3782 DESCRIPTION The FUJITSU MICROELECTRONICS MB3782 is a PWM-type switching regulator controller, designed with opencollector output for connection to external drive transistors and coils, providing a selection of three types of output voltage: step-up, step-down or inverting (inverting output is available on one circuit only). The MB3782 features identical oscillator output waveforms to enable completely synchronous operation and prevent the occurrence of low-frequency beat between channels. Also, the MB3782 features low power dissipation (2.1 mA Typ) and a built-in standby mode (10 A), making possible the configuration of a wide variety of high-efficiency, stable power supplies, even with the use of battery power. The MB3782 is an ideal power supply for high-performance portable devices such as video camcorders and cameras. FEATURES * * * * * * * * * Wide voltage range (3.6 V to 18 V) Low power dissipation (operating mode: 2.1 mA (Typ), standby mode: 10 A (Max) Wide range of oscillator frequencies, high-frequency capability (1 kHz to 500 kHz) On-chip timer-latch type short detection circuit On-chip undervoltage lockout circuit On-chip 2.50 V reference voltage circuit (1.25 V output available at RT pin) Dead time adjustment over full duty cycle range On-chip standby mode (power on/off function) One type of package (SOP-20pin : 1 type) APPLICATIONS * LCD monitor/panel * Surveillance camera etc. Copyright(c)1995-2008 FUJITSU MICROELECTRONICS LIMITED All rights reserved 2006.5 MB3782 PIN ASSIGNMENT TOP VIEW VREF 1 20 VCC CT 2 19 CTL RT 3 18 - IN3 + IN1 4 17 FB3 - IN1 5 16 DTC3 FB1 6 15 OUT3 DTC1 7 14 SCP PUT1 8 13 - IN2 GND 9 12 FB2 OUT2 10 11 DTC2 (FPT-20P-M01) PIN DESCRIPTION Pin No. Pin Name I/O Description 1 VREF O 2.50 V (typ) voltage output: provides load current up to 3 mA, for use as error amplifier reference input and for dead time setting. 2 CT -- Oscillator timing capacity connection: should be used in the capacity range 150 pF to 15000 pF. Oscillator timing resistor connection: should be used in the resistance range 5.1 k to 100 k. This pin can also provide output at voltage level VREF/2, for use as error amplifier reference input. 3 RT -- 4 +IN1 I Error amplifier 1 non-inverting input pin. 5 -IN1 I Error amplifier 1 inverting input pin. 6 FB1 O Error amplifier 1 output pin: connect resistor and capacitor between this pin and the -IN1 pin to set gain and adjust frequency characteristics. I OUT1 dead time setting pin: VREF voltage is divided by an external resistor and applied to set dead time. Also, a capacitor may be connected between this pin and the GND pin to perform soft start operations. 7 DTC1*1 (Continued) 2 MB3782 (Continued) Pin No. Pin Name I/O Description 8 VOUT1 O Open collector type output pin with an emitter connected to GND. Output current may be up to 50 mA. 9 GND -- Ground pin 10 OUT2 O Open collector type output pin with an emitter connected to GND. Output current may be up to 50 mA. 11 DTC2* I Used to set OUT2 pin dead time. VREF voltage is divided by an external resistor and applied to set dead time. Also, a capacitor may be connected between this pin and the GND pin to perform soft start operations. 12 FB2 O Error amplifier 2 output pin: connect resistor and capacitor between this pin and the -IN2 pin to set gain and adjust frequency characteristics. 13 -IN2 I Error amplifier 2 inverting input pin. 1 14 SCP*2 -- Time constant setting capacitor connection for timer-latch type short prevention circuit: a capacitor should be connected between this pin and the GND pin. For details, see " Setting the Time Constant for the Timer-Latch Type Short Prevention Circuit." 15 OUT3 O Open collector type output pin for emitter connected to GND. Output current may be up to 50 mA. 16 DTC3* I Used to set OUT3 pin dead time. VREF voltage is divided by an external resistor and applied to set dead time. Also, a capacitor may be connected between this pin and the GND pin to perform soft start operations. 17 FB3 O Error amplifier 3 output pin: connect resistor and capacitor between this pin and the -IN3 pin to set gain and adjust frequency characteristics. 18 -IN3 I Error amplifier 3 inverting input pin. 19 CTL I Power supply control pin: low level places the IC in standby mode and reduces power consumption to 10 A or lower. Input level may be driven by TTL or CMOS. 20 VCC -- 1 Power supply pin: voltage range is 3.6 V to 18 V. *1: DTC = Dead Time Control *2: SCP = Short Circuit Protection 3 MB3782 BLOCK DIAGRAM RT CT VREF VCC CLT 3 2 1 20 19 1.25 V 2.5 V Reference voltage source Triangular wave oscillator Error Amp 1 + IN1 4 - IN1 5 FB1 DTC1 6 9 GND 8 OUT1 10 OUT2 15 OUT3 PWM Comp.1 Ch.1 + + + - - 7 Error Amp 2 - IN2 Power on/off control circuit 13 PWM Comp.2 - Ch.2 + + - + 1.25 V FB2 DTC2 12 - IN3 18 11 Error Amp 3 PWM Comp.3 + + - + 1.25 V FB3 17 DTC3 16 SCP Comp. + 2.1 V VREF 1 A SCP 14 S R Latch 4 U.V.L.O. Ch.3 MB3782 FUNCTIONAL DESCRIPTIONS 1. Reference Voltage Source The reference voltage source uses the voltage provided at the VCC pin (pin 20) to generate a temperaturecompensated reference voltage ( 2.50 V), which is used as the operating power supply for the internal circuits of the IC. The reference voltage source can be output through the VREF pin (pin 1). 2. Triangular Wave Oscillator By connecting a timing capacitor and resistor respectively to the CT pin (pin 2) and RT pin (pin 3), the oscillator can provide a triangular waveform at any desired frequency. The waveform has an amplitude of 1.3 V to 1.9 V, and can be connected to the non-inverting input of the onchip PWM comparator and also output through the CT pin (pin 2). 3. Error Amps The error amps are amplifiers that detect the output voltage of the switching regulator and send the PWM control signal. The common-mode input voltage range is 1.05 V to 1.45 V, so that the voltage applied to the non-inverting input pin as a reference voltage should be either the voltage obtained by dividing the IC reference voltage output (recommended value: VREF/2) or the voltage obtained from the RT pin (pin 3) (1.25 V). The non-inverting input for the error amps 1 and 2 is internally connected to VREF/2 voltage. Also, a feedback transistor and capacitor can be connected between the error amp output pin and inverting input pin to provide any desired level of loop gain, enabling stable phase compensation. 4. Timer Latch (S-R Latch) Type Short Prevention Circuit The timer-latch type short prevention circuit detects the output levels from each of the error amps. Whenever one or more error amps produces an output level of 2.1 V or higher, the timer circuit is activated starting the charging of the external protection enabler capacitor. If the error amp output voltage does not return to normal range before the voltage in this capacitor reaches the transistor's base-emitter junction voltage (VBE ( 0.65 V)), the latch circuit will operate to turn the output transistor off and at the same time set the dead time to 100%. Once the prevention circuit is activated, the power must be switched on again to resume normal operation. 5. Low Input Voltage Fault Prevention Circuit (Under Voltage Lock-Out (UVLO) function) When power is switched on, excess power or momentary drops in power line current can cause operating faults in the controller IC, which can in turn lead to damage or deterioration in systems. The low input voltage fault prevention circuit detects the internal reference voltage level with respect to the power supply voltage level and acts to reset the latch circuit, thereby turning the output transistor off and at the same time setting the dead time to 100% and holding the SCP pin (pin 14) at "low." Operation returns to normal when the power supply voltage reaches or exceeds the UVLO threshold voltage level. 6. PWM Comparator The PWM comparator is a voltage comparator with one inverting and two non-inverting inputs, which acts as a voltage to pulse width converter controlling the on-time of the output pulse according to the input voltage level. When the triangular waveform produced by the oscillator is lower than either the error amp output or the DTC pin voltage, the output transistor is switched on. It is also possible to use the DTC terminal to provide a soft start function. 7. Output Transistor The output is open-collector type, with the emitter of the output transistor connected to the GND pin. The power transistor for external switching can carry a base current of up to 50 mA. 8. Power Supply Control Power supply on/off control is enabled through the CTL pin (pin 19). (In standby mode, power supply current is 10 A or less.) 5 MB3782 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Condition Power supply voltage VCC Error amp input voltage Dead time control input voltage Rating Unit Min Max -- -- 20 V VIN -- -0.3 +10 V Vdt -- -0.3 +2.8 V Control input voltage VCTL -- -0.3 +20 V Collector output voltage VOUT -- -- 20 V Collector output current IOUT -- -- 75 Allowable loss Operating ambient temperature Storage temperature Ta +25C D 1 P * SOP Version mA -- 740* mW 2 Ta -- -30 +85 C Tstg -- -55 +125 C *1: For operation in conditions where Ta > +25C, and the SOP version should be derated by 7.4 mW/C. *2: When mounted on a 4 cm-square dual-sided epoxy board. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. RECOMMENDED OPERATING CONDITIONS Parameter Symbol Condition Power supply voltage VCC Error amp input voltage Value Unit Min Typ Max -- 3.6 6.0 18.0 V VIN -- 1.05 -- 1.45 V Control input voltage VCTL -- 0 -- 18 V Collector output voltage VOUT -- -- -- 18 V Collector output current IOUT -- 0.3 -- 50 mA Reference voltage output current IREF -- -3 -1 0 mA Timing capacitance CT -- 150 -- 15000 pF Timing resistance RT -- 5.1 -- 100 k fOSC -- 1 -- 500 kHz Ta -- -30 +25 +85 C Oscillator frequency Operating ambient temperature WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their representatives beforehand. 6 MB3782 ELECTRICAL CHARACTERISTICS Dead time controller Triangular wave Short circuit protection Undervoltage lock oscillator (DTC) (SCP) out circuit (UVLO) Reference voltage Parameter Symbol Conditions Output voltage VREF IOR = -1 mA Output voltage temperature variation VRTC Input stability Load stability Short output current Threshold voltage Hysteresis width Reset voltage (VCC) Min (VCC = 6 V, Ta = +25C) Value Unit Typ Max 2.45 2.50 2.55 V Ta = -30C to +85C -2 0.2 +2 % Line VCC = 3.6 V to 18 V -- 2 10 mV Load IOR = -0.1 mA to -1 mA -- 1 7.5 mV -30 -10 -3 mA IOS VREF = 2 V VtH IOR = -0.1 mA -- 2.72 -- V VtL IOR = -0.1 mA -- 2.60 -- V VHYS IOR = -0.1 mA 80 120 -- mV VR -- 1.5 1.9 -- V Input threshold voltage VtPC -- 0.60 0.65 0.70 V Input standby voltage VSTB No pull-up -- 50 100 mV Input latch voltage VIN No pull-up -- 50 100 mV Input source current Ibpc -1.4 -1.0 -0.6 A Comparator threshold voltage VtC Pin 6, pin 12, pin 17 -- 2.1 -- V Oscillator frequency fOSC CT = 330 pF, RT = 15 k 160 200 240 kHz Frequency deviation fdev CT = 330 pF, RT = 15 k -- 5 -- % Frequency deviation (VCC) fdV VCC = 3.6 V to 18 V -- 1 -- % Frequency deviation (Ta) fdT Ta = -30C to +85C -4 -- +4 % Vt0 Duty cycle = 0 % 1.05 1.3 -- V Duty cycle = 100 % -- 1.9 2.25 V Vdt = VR/1.45 V 55 65 75 % -- 0.2 1 A Input threshold voltage Vt100 -- ON duty cycle Dtr Input bias current Ibdt Latch mode sink current Idt Vdt = 2.5 V 150 500 -- A Latch input voltage Vdt Idt = 100 A -- -- 0.3 V -- (Continued) 7 MB3782 (Continued) Parameter Error amps PWM comparator Control block Conditions Min Input offset voltage VIO VOUT = 1.6 V -6 -- +6 mV Input offset current IIO VOUT = 1.6 V -100 -- +100 nA Input bias current IB VOUT = 1.6 V -500 -100 -- nA VCC = 3.6 V to 18 V 1.05 -- 1.45 V 70 80 -- dB -- 0.8 -- MHz Common mode input voltage range Entire Output device block Symbol (VCC = 6 V, Ta = +25C) Value Unit Typ Max VICR Voltage gain Av Frequency bandwidth BW Common mode rejection ratio -- Av = 0 dB CMRR -- 60 80 -- dB Maximum output voltage range VOM+ -- VREF -0.3 -- -- V VOM- -- -- 0.7 0.9 V Output sink current IOM+ VOUT = 1.6 V -- 1.0 -- mA Output source current IOM- VOUT = 1.6 V -- -60 -- A Vt0 Duty cycle = 0 % 1.05 1.3 -- V Input threshold voltage Vt100 Duty cycle = 100 % -- 1.9 2.25 V Input sink current IIN+ Pin 6, pin 12, pin 17 -- 1.0 -- mA Input source current IIN- Pin 6, pin 12, pin 17 -- -60 -- A Input OFF conditions VOFF -- -- -- 0.7 V Input ON conditions VON -- 2.1 -- -- V Control pin current ICTL VCTL = 10 V -- 200 400 A Output leak current Leak VOUT = 18 V -- -- 10 A Output saturation voltage VSAT IOUT = 50 mA -- 1.1 1.4 V Standby current ICCS VCTL = 0 V -- -- 10 A Average feed current ICCa VCTL = VCC, no output load -- 2.1 3.2 mA Notes : * Voltage control on channel 1 may be positive or negative. * The non-inverting input to the error amps on channel 2 and channel 3 is internally connected to VREF/2, and therefore voltage control is positive only. * VREF/2 output can be obtained from the RT pin. 8 MB3782 SETTING THE TIME CONSTANT FOR THE TIMER-LATCH TYPE SHORT PREVENTION CIRCUIT Figure 1 shows the configuration of the protection latch circuit. The output lines from the error amps are each connected to the inverting input lines of the short protection comparator, which constantly compares them with the reference voltage of approximately 2.1 V connected to the non-inverting input. When load conditions in the switching regulator are stabilized, there is no variation in the output from the error amps, and therefore the short prevention controls are held in equilibrium. In this situation, voltage at the SCP pin (pin 14) is held at approximately 50 mV. When load conditions change rapidly, as in the case of a load short, high potential signal (greater than 2.1V) from the error amps is input to the inverting signal input of the short protection comparator, and the short protection comparator outputs a "low" level signal. The transistor Q1 is consequently switched off, so that short protection capacitor CPE externally connected to the SCP pin voltage is then charged according to the following formulas. VPE = 50 mV + tPE x 10-6/CPE 0.65 = 50 mV + tPE x 10-6/CPE CPE = tPE/0.6 (F) When the short protection capacitor is charged to a level of approximately 0.65 V, the SR latch is set and the low input voltage fault prevention circuit is enabled, turning the output drive transistor off. At the same time, the dead time is set to 100% and the SCP pin (pin 14) is held "low." This closes the S-R latch input and then discharges the capacitor CPE 2.50 V 1 A S.C.P.Comp. Error Amp 1 Error Amp 2 Error Amp 3 + 14 CPE Q1 Q3 S PWM Comp. R Latch Out U.V.L.O. 2.1 V Figure 1 Protection Latch Circuit 9 MB3782 SETTING OUTPUT VOLTAGE The following diagrams show the connections used to set the output voltage. Because the power supply to the error amps is provided by the same reference voltage circuit used for the other internal circuits, the common-mode input voltage range is set at 1.05 V to 1.45 V. The reference voltage input to the +IN and -IN pins should be set at 1.25 V (VREF/2). The method of connection for channel 1 is different from channel 2 and channel 3. In addition, channel 1 is capable of picking up both positive and negative voltages, while channel 2 and channel 3 can pick up only positive output voltages. VREF V0 + R V0 + = VREF x (R1 + R2) 2R2 R1 + - R R2 pin 6 RNF Figure 2 Error amp (channel 1) connection: Output voltage VO positive VREF VREF V0 - = - 2xR2 x (R1 + R2) + VREF R R1 + - R R2 pin 6 RNF V0 - Figure 3 Error amp (channel 1) connection: Output voltage VO positive 10 MB3782 V0 + V0 + = 1.25 x (R1 + R2) R2 R1 + - R2 pin 12,17 RNF 1.25 V Figure 4 Error amp (channel 2, channel 3) connection The non-inverting input to the error amps on channel 2 and channel 3 is internally connected to VREF/2, and therefore cannot be configured for inverting output. ch.1 ch.2 ch.3 Step up Step down Inverting x x 11 MB3782 USING THE RT PIN The triangular waves, as shown in Figure 5, act to set the oscillator frequency by charging and discharging the capacitor connected to the CT pin using the current value of the resistor connected to the RT pin. In addition, when voltage level VREF/2 is output to external circuits from the RT pin, care must be taken in making the external circuit connections to adjust for the fact that I1 is increased by the value of the current I2 to the external circuits in determining the oscillator frequency (see Figure 6). ICT = IRT Triangular wave oscillator = VREF 2RT VREF 2 2 1 IRT ICT CT RT Figure 5 No VREF/2 connection to external circuits from RT pin ICT = IRT Triangular wave generator = I1 + I2 = VREF 2 2 VREF + I2 2RT 1 IRT ICT To external circuits IRT I1 RT Figure 6 12 CT VREF/2 connection to external circuits from RT pin MB3782 TREATMENT OF UNUSED ERROR AMPS Any error amps that are not used should be handled as follows. Note that failure to apply proper treatment to error amps will cause the SCP circuit to activate and disable the switching regulator output. 1. Error Amp (channel 1) Not In Use 1 VREF 3 5 RT + IN1 - IN1 7 DTC1 9 GND 4 Note: Pin 6 and pin 8 shoud be left open. 2. Error Amp (channel 2) Not In Use 1 VREF 9 - IN2 GND DTC2 13 11 Note: Pin 10 and pin 12 shoud be left open. 3. Error Amp (channel 3) Not In Use 1 VREF - IN3 18 DTC3 16 9 GND Note: Pin 15 and pin 17 shoud be left open. 13 MB3782 TREATMENT OF UNUSED SCP PIN When the timer latch short protection circuit is not used, the SCP pin (pin 14) should be connected to the GND by the shortest possible path. SCP 14 14 MB3782 TEST CIRCUIT OUTPUT OUTPUT 4.7 k 4.7 k 1 20 2 19 3 18 4 17 TEST 5 16 INPUT 6 15 7 14 8 13 9 12 TEST 10 11 INPUT VCC 330 pF CTL 150 k 4.7 k TEST OUTPUT INPUT CPF 15 MB3782 TIMING CHART (INTERMAL WAVEFORMS) CT pin wavefoms Short protection comparator reference input Dead time,PWM input voltage 2.1 V 1.9 V 1.6 V 1.3 V Error amp output "High" PWM comparator output Output transistor-collector waveforms "Low" Dead time 100 % "High" "Low" 0.6 V SCP pin waveforms 0V tPE "High" Short protection comparator output "Low" Power ON Power OFF 2.1 V Control pin voltage (VCTL: minimum value) 0V 3.6V Power supply voltage (VCC: minimum) 0V 16 Protection enable time tPE 0.6 x 106 x CPE (s) MB3782 EXAMPLE OF APPLICATION 16 k 5.6 k 9.1 k 1 F 1.8 k 1 F 1 F 5.6 H 10 k 4.7k 10 k 2.4 k 10 k 4.7 k V IN (6V) CTL 4.7 k 4 +IN1 4.7 k 0.033 F 150 k 1 VREF 7 DTC1 11 DTC2 16 20 19 DTC3 VCC CTL 330 OUT1 8 5 -IN1 330 120 H 6 FB1 1.8 k 330 0.033 F 150 k 1.8 k 0.033 F 150 k OUT2 10 13 -IN2 12 FB2 + 220 F - 120 H 220 F + - 3.9 k 17 FB3 VO+ (+5V) 330 MB3782 18 -IN3 820 pF VO- (-5V) 120 H VO+ (+12V) 100 OUT3 15 2 CT 8.2 k 0.1 F 3 RT GND 9 14 SCP 17 MB3782 TYPICAL CHARACTERISTICS CURVES Reference voltage vs. Power supply voltage 3.0 Ta = +25C Average feed current (mA) Reference voltage VREF (V) 5.0 Average feed current vs. Power supply voltage 2.5 Ta = +25C 1.5 0 0 0 4 8 12 16 0 20 4 Reference voltage vs. Operating ambient temperature 2.51 VCC = VCTL = 6 V IOR = -1 mA 2.50 2.49 2.48 2.47 2.46 2.45 - 40 8 12 16 20 Power supply voltage VCC (V) Triangular wave maximum amplitude voltage vs. Timing capacitance 2.2 Triangular wave maximum amplitude voltage (V) Reference voltage VREF (V) Power supply voltage VCC (V) VCC = 6 V RT = 15 k Ta = +25C 2.0 1.8 1.6 1.4 1.2 1.0 0.8 - 20 0 + 20 + 40 + 60 + 80 + 100 Operating ambient temperature Ta (C) 104 103 102 Timing capacitance CT (pF) 2.0 VCC = 6 V Ta = +25C 1.5 1.0 0.5 0 0 10 20 30 40 50 Error amp maximum output voltage amplitude (V) Collector saturation voltagre VOL (V) Collector saturation voltage vs. Sink current Error amp maximum output voltage amplitude vs. Frequency 3.0 VCC = 6 V Ta = +25C 2.0 1.0 0 100 500 1 k 5 k 10 k 50 k 100 k 500 k Fequency f (Hz) Sink current IOL (mA) (Continued) 18 MB3782 Oscillator frequency vs. Timing resistance VCC = 6 V Ta = +25C Triangular wave period vs. Timing capacitance 100 VCC = 6 V RT = 15 k Ta = +25C 100 k CT = 150 pF 10 k Triangular wave period (s) Oscillator frequency fOSC (Hz) 1M 10 CT = 1500 pF 1 102 CT = 15000 pF 103 104 105 Timing capacitance CT (pF) 1k 1k 5 k 10 k 50 k 100 k 500 k Timing resistance RT () Frequency variation vs. Operating ambient temperature ON duty cycle vs. Oscillator frequency 0 ON duty Cycle Dtr (%) 100 VCC = 6 V CT = 330 pF RT = 15 k VCC = 6 V CT = 1330 pF RT = 15 k Ta = +25C 80 60 40 20 0 -10 -40 -20 0 +20 +40 +60 5k +80 +100 +120 10 k 50 k 100 k 500 k 1 M Oscillator frequency (Hz) Operating ambient temperature Ta (C) Reference voltage vs. Control input voltage Control input current vs. Control input voltage VCC = 6 V CT = +25C 5.0 Control input current ICTL (A) Reference voltage VREF (V) Frequency variation fDT (%) 10 2.5 0 VCC = 6 V CT = +25C 500 250 0 0 1 2 3 4 Control input voltage VCTL (V) 5 0 4 8 12 16 20 Control input voltage VCTL (V) (Continued) 19 MB3782 0 0 -20 -90 -40 -180 100 1k 10 k 100 k 90 0 0 -20 -90 1M -180 10 100 1k 10 k 100 k Frequenncy f (Hz) Frequenncy f (Hz) Voltage gain and phase vs. Frequenncy Voltage gain and phase vs. Frequenncy CNF = 470 pF 40 20 180 90 AV 0 0 -20 -90 -40 10 AV 20 -40 -180 100 1k 10 k 100 k AV 20 180 90 0 0 -20 -90 -40 1M 1M CNF = 4700 pF 40 Phase (deg) 10 Voltage gain AV (dB) 90 Phase (deg) 20 CNF = 0.047 pF 180 40 Voltage gain AV (dB) Voltage gain AV (dB) 180 AV Phase (deg) CNF = open 40 Voltage gain AV (dB) Voltage gain and phase vs. Frequenncy Phase (deg) Voltage gain and phase vs. Frequenncy -180 10 100 Frequenncy f (Hz) 1k 10 k 100 k 1M Frequenncy f (Hz) Test Circuit VREF VREF CNF 4.7 k 4.7 k 240 k 4 IN 10 F - + 4.7 k 6 OUT 5 + 4.7 k Error amp (Continued) 20 MB3782 (Continued) Allowable loss PD (mW) Allowable loss vs. Operating ambient temperature 1200 1110 1000 800 740 600 SOP version 400 200 0 -30 -20 -10 0 +10 +20 +30 +40 +50 +60 +70 +80 +85 Operating ambient temperature Ta (C) 21 MB3782 CONCERNING EQUIVALENT SERIES RESISTANCE AND STABILITY OF SMOOTHING CAPACITORS In DC/DC converters, the equivalent series resistance value (ESR) of smoothing capacitors has a major influence on loop phase characteristics. The ESR is a means by which phase characteristics approximate phase relationships to ideal capacitors in highfrequency bands (see Graph 1), thus improving system stability. At the same time, the use of smoothing capacitors with low ESR reduces system stability, so that care must be taken when using semiconductor electrolytic capacitors (OS-CONTM*) or tantalum capacitors with low ESR. * : OS-CON is a trademark of Sanyo Electric Co., Ltd. L Tr Rc VIN D RL C Figure 7 Basic circuit for step-down voltage DC/DC converter Phase vs. frequency Gain vs. frequency 0 20 - 20 - 40 - 60 10 Phase (deg) Gain (dB) 0 2 1 : Rc = 0 1 : Rc = 0 1 2 : Rc = 31 m 100 2 - 90 1k 10 k - 180 100 k 10 100 Frequency f (Hz) 1k Frequency f (Hz) Graph 1 22 1 2 : Rc = 31 m Gain and phase vs. frequency 10 k 100 k MB3782 * Reference data Changing the smoothing capacitor from an aluminum electrolytic capacitor (RC 1.0) to a lower-ESR semiconductor electrolytic capacitor (OS-CONTM: RC 0.2 ) decreases the phase margin (see Graphs 2, 3). V out V0 + CNF AV and phase characteristics measured between these points - IN - FB + IN + VIN R2 R1 VREF/2 Error amp Figure 8 Measurement of DC/DC Capacitor AV and Phase () Characteristics DC/DC converter + 5 V output Gain and Phase vs. Frequency Graph 2 60 Vcc = 10 V RL = 25 Cp = 0.1 F Gain (dB) Av 180 V0 + 20 90 62 0 0 - 20 Phase (deg) 40 + - Aluminum electrolytic capacitor 220 F (16 V) RC 1.0 : fosc = 1 kHz - 90 - 40 10 100 1k - 180 100 k 10 k Frequency f (Hz) Graph 3 DC/DC converter + 5 V output Gain and Phase vs. Frequency 60 180 90 20 0 27 + - OS-CONTM 22 F (16 V) RC 0.2 : fosc = 1 kHz - 90 - 20 - 40 10 0 Phase (deg) 40 Gain (dB) Vcc = 10 V RL = 25 Cp = 0.1 F Av 100 1k 10 k - 180 100 k Frequency f (Hz) 23 MB3782 NOTES ON USE * Take account of common impedance when designing the earth line on a printed wiring board. * Take measures against static electricity. - For semiconductors, use antistatic or conductive containers. - When storing or carrying a printed circuit board after chip mounting, put it in a conductive bag or container. - The work table, tools and measuring instruments must be grounded. - The worker must put on a grounding device containing 250 k to 1 M resistors in series. * Do not apply a negative voltage - Applying a negative voltage of -0.3 V or less to an LSI may generate a parasitic transistor, resulting in malfunction. ORDERING INFORMATION Part number Package Remarks MB3782PF- 20 pin plastic SOP (FPT-20P-M01) Conventional version MB3782PF-E1 20 pin plastic SOP (FPT-20P-M01) Lead Free version RoHS Compliance Information of Lead (Pb) Free version The LSI products of Fujitsu Microelectronics with "E1" are compliant with RoHS Directive , and has observed the standard of lead, cadmium, mercury, Hexavalent chromium, polybrominated biphenyls (PBB) , and polybrominated diphenyl ethers (PBDE) . The product that conforms to this standard is added "E1" at the end of the part number. MARKING FORMAT (Lead Free version) MB3782 XXXX XXX E1 SOP-20 INDEX Lead Free version 24 MB3782 LABELING SAMPLE (Lead free version) Lead free mark JEITA logo MB123456P - 789 - GE1 (3N) 1MB123456P-789-GE1 1000 (3N)2 1561190005 107210 JEDEC logo G Pb QC PASS PCS 1,000 MB123456P - 789 - GE1 2006/03/01 ASSEMBLED IN JAPAN MB123456P - 789 - GE1 1/1 0605 - Z01A 1000 1561190005 Lead Free version 25 MB3782 MB3782PF-E1 RECOMMENDED CONDITIONS OF MOISTURE SENSITIVITY LEVEL Item Condition Mounting Method IR (infrared reflow) , Manual soldering (partial heating method) Mounting times 2 times Storage period Before opening Please use it within two years after Manufacture. From opening to the 2nd reflow Less than 8 days When the storage period after opening was exceeded Please processes within 8 days after baking (125 C, 24H) 5 C to 30 C, 70%RH or less (the lowest possible humidity) Storage conditions [Temperature Profile for FJ Standard IR Reflow] (1) IR (infrared reflow) H rank : 260 C Max 260 C 255 C 170 C to 190 C (b) RT (a) (a) Temperature Increase gradient (b) Preliminary heating (c) Temperature Increase gradient (d) Actual heating (d') (e) Cooling (2) Manual soldering (partial heating method) Times 26 : 5 s max/pin (d) (e) (d') : Average 1 C/s to 4 C/s : Temperature 170 C to 190 C, 60s to 180s : Average 1 C/s to 4 C/s : Temperature 260 C Max; 255 C or more, 10s or less : Temperature 230 C or more, 40s or less or Temperature 225 C or more, 60s or less or Temperature 220 C or more, 80s or less : Natural cooling or forced cooling Note : Temperature : the top of the package body Conditions : Temperature 400 C Max (c) MB3782 PACKAGE DIMENSION 20-pin plastic SOP (FPT-20P-M01) 20-pin plastic SOP (FPT-20P-M01) Lead pitch 1.27 mm Package width x package length 5.3 x 12.7 mm Lead shape Gullwing Sealing method Plastic mold Mounting height 2.25 mm MAX Weight 0.28 g Code (Reference) P-SOP20-5.3x12.7-1.27 Note 1) *1 : These dimensions include resin protrusion. Note 2) *2 : These dimensions do not include resin protrusion. Note 3) Pins width and pins thickness include plating thickness. Note 4) Pins width do not include tie bar cutting remainder. +0.25 +.010 +0.03 *112.70 -0.20 .500 -.008 0.17 -0.04 +.001 20 .007 -.002 11 *2 5.300.30 7.800.40 (.209.012) (.307.016) INDEX Details of "A" part +0.25 2.00 -0.15 +.010 .079 -.006 1 "A" 10 1.27(.050) 0.470.08 (.019.003) 0.13(.005) (Mounting height) 0.25(.010) 0~8 M 0.500.20 (.020.008) 0.600.15 (.024.006) +0.10 0.10 -0.05 +.004 .004 -.002 (Stand off) 0.10(.004) C 2002 FUJITSU LIMITED F20003S-c-7-7 Dimensions in mm (inches). Note: The values in parentheses are reference values. 27 FUJITSU MICROELECTRONICS LIMITED Shinjuku Dai-Ichi Seimei Bldg. 7-1, Nishishinjuku 2-chome, Shinjuku-ku, Tokyo 163-0722, Japan Tel: +81-3-5322-3347 Fax: +81-3-5322-3387 http://jp.fujitsu.com/fml/en/ For further information please contact: North and South America FUJITSU MICROELECTRONICS AMERICA, INC. 1250 E. Arques Avenue, M/S 333 Sunnyvale, CA 94085-5401, U.S.A. Tel: +1-408-737-5600 Fax: +1-408-737-5999 http://www.fma.fujitsu.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD. 151 Lorong Chuan, #05-08 New Tech Park, Singapore 556741 Tel: +65-6281-0770 Fax: +65-6281-0220 http://www.fujitsu.com/sg/services/micro/semiconductor/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Pittlerstrasse 47, 63225 Langen, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://emea.fujitsu.com/microelectronics/ FUJITSU MICROELECTRONICS SHANGHAI CO., LTD. Rm.3102, Bund Center, No.222 Yan An Road(E), Shanghai 200002, China Tel: +86-21-6335-1560 Fax: +86-21-6335-1605 http://cn.fujitsu.com/fmc/ Korea FUJITSU MICROELECTRONICS KOREA LTD. 206 KOSMO TOWER, 1002 Daechi-Dong, Kangnam-Gu,Seoul 135-280 Korea Tel: +82-2-3484-7100 Fax: +82-2-3484-7111 http://www.fmk.fujitsu.com/ FUJITSU MICROELECTRONICS PACIFIC ASIA LTD. 10/F., World Commerce Centre, 11 Canton Road Tsimshatsui, Kowloon Hong Kong Tel: +852-2377-0226 Fax: +852-2376-3269 http://cn.fujitsu.com/fmc/tw All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU MICROELECTRONICS device; FUJITSU MICROELECTRONICS does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU MICROELECTRONICS assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU MICROELECTRONICS or any third party or does FUJITSU MICROELECTRONICS warrant non-infringement of any third-party's intellectual property right or other right by using such information. FUJITSU MICROELECTRONICS assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU MICROELECTRONICS will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws. The company names and brand names herein are the trademarks or registered trademarks of their respective owners. Edited Strategic Business Development Dept.