Technical Support: (888) 41-ASTEC or (407) 241-2752
Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662
121
Special Features
Electrical Specs
175 Watts
LPQ170 Series
Total Power: 110-175 Watts
Input Voltage: 85-264 VAC
120-300 VDC
# of Outputs: Quad
• Active power factor correction
• IEC EN61000-3-2 compliance
• Adjustable outputs on 1, 3 & 4
Remote sense on main output
• Single wire current sharing
• Power fail and remote inhibit
• Built-in EMI filter
• Low output ripple
• Overvoltage protection
• Overload protection
• Thermal overload protection
• DC power good
• 5 V standby output
• Adjustable floating 4th output
• Optional cover (-C suffix)
Operating temperature: 0° to 50°C ambient
Low temperature start -20°C
Derate each output at 2.5% per degree from
50° to 70°C (except for -C version)
Electromagnetic susceptibility: designed to
meet EN61000-4, -2, -3, -4, -5, -6, -8, -11,
Level 3
Humidity: Operating; non-condensing
5% to 95%
Vibration: Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major
resonances 0.75 G peak 5 Hz to 500 Hz,
operational
Storage temperature: -40° to 85°C
Temperature coefficient: ± .04% per °C
MTBF demonstrated: >550,000 hours at full
load and 25°C ambient conditions
Input
Input range 85-264 VAC, 120-300 VDC
Frequency 47-63 Hz
Inrush current 38 A max, cold start @ 25°C
Efficiency 75% typical at full load
EMI filter Meets FCC Class B conducted
CISPR 22 Class B conducted
EN55022 Class B conducted
VDE 0878 PT3 Class B conducted
Power factor 0.99 typical
Safety ground leakage
current 1.0 mA @ 50/60 Hz, 264 VAC input
Output
Maximum power 110 W convection (75 W with cover LPQ172)
85 W convection - LPQ173
175 W with 30 CFM forced air
(130 W with cover - LPQ172 only)
Adjustment range 3.3 - 5.5V on main; -12 - 15V on 3rd output
3.3 - 25 V on 4th output- LPQ172
3.3 - 5.5V on 4th output on LPQ173
Hold-up time 20 ms @175 W load at nominal line
Overload protection Short circuit protection on all outputs. Case
overload protected @ 110-145% above peak
rating
Overvoltage protection Tracks outputs 1, 3 & 4; 15 to 35%
Standby output 5 V @ 200 mA regulated ±5%
Logic Control
AC power failure TTL logic signal goes high 100 - 500 msec
after V1 output; It goes low at least 4 msec
before loss of regulation
Remote inhibit Requires contact closure to inhibit outputs
Remote sense Compensates for 0.5 V lead drop min. Will
operate without remote sense connected.
Reverse connection protected.
DC-OK TTL logic signal goes high after main output
is in regulation. It goes low when there is a
loss of regulation
Environmental
Safety
VDE 0805/EN60950/IEC60950
UL 60950
CB Certificate and report
CSA CSA 60950 Level 3
CE Mark (LVD)
NEMKO EN 60950/EMKO-TSE
rev 09.20.04
EUROPE
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
AMERICAS
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
122
www.astecpower.com
Ordering Information
ASIA
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Model Output Minimum Maximum Load with Maximum Load with Peak Regulation2 Ripple
Number Voltage Load Convection Cooling 30 CFM Forced Air Load P/P(PARD)3
LPQ172 5 V (3.3 - 5.5 V) 0 A 15 A 30 A 32 A ±2% 50 mV
12 V 0 A 6 A 8 A 10 A ±3% 120 mV
-12 V (-12 -15 V) 0 A 1.5 A 3 A 3.5 A ±3% <1%
±3.3-25 V 0.5 A* 2 A 5 A 5.5 A ±3% <50mV or 1%
LPQ173 5 V (3.3 - 5.5 V) 0 A 10 A 24 A 26 A ±2% 50 mV
12 V 0 A 6 A 8 A 10 A ±3% 120 mV
-12 V (-12 -15 V) 0 A .2 A 3 A 3.5 A ±3% <1%
5 V (3.3 - 5.5 V) 0 A 10A 24 A 26 A ±2% 50mV
1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4. 4th output adjustable 3.3-25 V factory set at 5 V.
5. *Minimum loads are required when output set below 5 Volts
6. Remote inhibit resets OVP latch
7. LPQ173-C has no convection rating.
Note: -C suffix added to the model number indicates cover option and is limited to 50C operation.
Connector LPQ172 LPQ173
SK1 PIN 1 N/C V4 SWP
PIN 2 5V Standby 5V Standby
PIN 3 N/C +V4 Sense
PIN 4 V1 SWP V1 SWP
PIN 5 Common Common
PIN 6 +V1 sense +V1 sense
PIN 7 Sense common Sense common
PIN 8 Remote inhibit Remote inhibit
PIN 9 DC power good DC power good
PIN 10 POK POK
SK2 PIN 1,2 +12 V +12V
PIN 3,4,5 Common Common
PIN 6 -12 V -12V
PIN 7 POK POK
PIN 8 +3.3 V to +25 V (Float) N/C
PIN 9 Common (Float) N/C
SK3 TB-1, 3 COMMON COMMON
TB-2 +5 V (3.3V to 5.5V) +5V (3.3V to 5.5V)
TB-4 N/C +5 (3.3V to 5.5V)
SK4 PIN 1 GROUND GROUND
PIN 3 LINE LINE
PIN 5 NEUTRAL NEUTRAL
Mating Connectors
(SK4) AC Input: Molex 09-50-8051 (USA)
Molex 09-91-0500 (UK)
PINS: 08-58-0111
(SK3) Main output:
Molex BB-124-08
(SK2) Aux DC Output/Power fail:
Molex 09-50-8091 (USA)
Molex 09-91-0900 (UK)
PINS: 08-58-0111
(SK1) Control Signals:
Molex 90142-0010 (USA)
PINS: 90119-2110 or
Amp: 87977-3
PINS: 87309-8
Astec connector kit #70-841-015, includes all of the above.
Pin Assignments
LPQ170 Series
EUROPE
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
AMERICAS
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
123
www.astec.com
Mechanical Drawing
ASIA
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Notes:
1. Specifications subject to change
without notice.
2. All dimensions in inches (mm),
tolerance is ±0.02”.
3. Specifications are for convection rating at
factory settings unless otherwise stated.
4. Mounting screw maximum insertion
depth is 0.12”.
5. Warranty: 1 year
6. Weight: 2 lb / 0.91 kg
SK2 SK1 SK3
LPQ170 Series
